Home

E-GO 0854331005018

image

Contents

1. YUNA AVIATION TECHNOLOGY IMDEX INDEX O2 sa INTRODUCTION GEAR 08 CHARGE SETUP OG SYNCING CONTROLLER AND BOARD 10 FEATURES SPECIFICATIONS 12 SAFETY WARNINGS AND TIPS rena TROUBLESHOOTING SPARE PARTS 20 INSTALLATION GUIDE INTRODUCTION Congratulations you have purchased an E GO You are now the owner of a portable eco friendly mode of transport that is incredibly fun to use Integrating state of the art motor technology developed by YUNEEC for use in the aviation industry E GO brings to the streets an experience and convenience that was never available in the past Setting aside dated conventions E GO focuses on what is essential to the design of a sustainable trans port unit that functions in todays urban areas Combining high performance with low consumption the E GO CRUISER allows you to travel up to 30Km 18Mi one full charge Its lightweight design and compact dimensions make the E GO the perfect wingman wherever you go simply pick up your board and step into a taxi bus train or indoor location Boarding is often linked to extreme sports activities like surfing skating or snowboarding and there are definitely similarities in the amount of freedom experienced when moving through space However E GO is foremost a city transport uni
2. 6 7 8 9 11 motor cover drive belt cover drive belt cover screw drive belt drive wheel washer drive wheel nut gt front truck screws battery pack screws ECU screws rear truck screws GARAGE MAKE SURE THE E GO IS POWERED OFF WHEN DOING MAINTENANCE OR REPLACING COMPONENTS DRIVE WHEEL AND BELT DEFORMING THE DRIVE BELT MIGHT DAMAGE IT REPLACE THE GRIP IT IS ADVICED TO CONSULT YOUR LOCAL SKATE SHOP 23 24 25 26 27 28 wheel nut washer bearing spacer truck axle wheel WHEELS AND BEARINGS TRUCKS AND 12 13 14 15 16 TZ king pin nut 18 top cup washer 19 top bushing 20 truck 21 bottom bushing 22 bottom cup washer BUSHINGS king pin baseplate nut baseplate baseplate rubber truck screw APPLY EQUAL PRESSURE ON THE OUTER RINGS OF THE BEARINGS TO PUSH THEM OUT OF AND INTO THE WHEEL TO AVOID DAMAGING THEM BATTERY 28 29 28 ECU Electronic Control Unit 29 battery pack 30 30 battery pack rubber PACK 29 AND ECU 31 lt lt 28 31 JST RCY connector 32 EC3 connector INSTALLATION GUIDE FRONT TRUCK SET EGOCRO11 1 Unscrew the front wheel bolts Dismount the front wheels from the truck s axle 3 Unscrew the top screws connecting the front baseplate to the deck 44 Replace the complete assem bly with the replacement part and reinstall E
3. reference troubleshoot page 19 10 11 12 13 THE TRUCK TOOL To keep your E GO s performance up to maximum you will need to do regular main tenance checks for more info on mainte nance please check page 17 making sure the board is not obstructed by dirt and all nuts and bolts are properly tightened To 15 tighten and loosen these nuts and bolts your E GO comes with a specific tool the truck tool that allows you to do that In 17 general you should make sure all parts are screwed on there nice and tight with the exception of the kingpin nut which can be adjusted according to your personal riding style hex tool 15 phillips tool 16 nut tool 17 kingpin nut tool START button axle nut tool throttle brake flash light 16 battery status indicator cS ae DINER 0 riding mode switch 11 speed mode switch 12 torch light switch Tightening the kingpin will give a more stable 13 mini USB port rigid ride Loosening the kingpin nut will make the board more maneuverable and decreases the diame ter of your turn radius allowing sharper turns charge status indicator red charging green charged Charge lead depending on sales area THE USB Use the USB to connect the wireless controller to the board s USB port to any computer or any other USB port for recharging purposes THE CHARGER The E GO charger allows you to fully recharge
4. DO NOT TAKE ANY PASSENGERS WITH YOU ON THE E GO DO NOT TAKE A CHILD IN YOUR ARMS OR IN A CHILD CARRIER WHILE RIDING DO NOT RIDE UNDER THE INFLUENCE OF DRUGS OR ALCOHOL DO NOT ATTEMPT TO RIDE IF YOU CAN NOT COMPLY FULLY WITH THE INSTRUCTIONS AND WARNING IN THIS GUIDE Te RIDER TIPS WHILE RIDING KEEP YOUR BACK STRAIGHT AND USE YOUR ARMS TO MAINTAIN BALANCE BENDING YOUR KNEES LOWERS YOUR BODY S CENTER OF GRAVITY WHICH INCREASES STABILITY SHIFT YOUR BODY WEIGHT TO THE FRONT WHEN ACCELERATING SHIFT YOUR BODY WEIGHT TO THE BACK WHEN BRAKING TO TURN CARVE DISPLACE YOUR BODY WEIGHT AND EXERT PRESSURE ON THE HEEL AND TOE SIDES OF THE BOARD YOUR TURNING RADIUS DEPENDS ON THE AMOUNT OF PRESSURE YOU EXERT ON THE SIDE OF THE BOARD MORE PRESSURE MEANS SHARPER TURNING CARVING WILL SLOW DOWN YOUR SPEED AND MAKES FOR AN ENERGY EFFICIENT WAY OF BRAKING BE MINDFUL WHEN TURNING CARVING AT HIGH SPEED YOU CAN ADJUST MANEU VERABILITY BY TIGHTENING OR LOOSENING THE KINGPIN NUTS ADJUST YOUR RIDING STYLE WHEN RIDING AT NIGHT OR IN CONDITIONS WITH LOW VISIBILITY ADAPT YOUR SPEED TO YOUR RIDING SKILL AND ENVIRONMENT DO NOT RIDE WHEN INTOXICATED BEWARE THAT WET FROZEN OILY OR UNPAVED SURFACES ARE UNSUITED FOR RIDING ON BEWARE THAT BRAKING DISTANCES VARY ACCORDING TO SURFACE TEXTURE HUMIDITY TEMPERATURE ETC AVOID RIDING OVER GUTTERS THIS MIGHT DAMAGE THE BOARD DO NOT EXPOSE E GO TO WATER DO NOT RIDE WHEN RAINING D
5. EXPOSE THE BATTERY TO FIRE OR WATER YUNEEC MADE IN CHINA AVIATION TECHNOLOGY INSTALLATION GUIDE BUSHING SET EGOCRO005 1 Unscrew the kingpin nut from the kingpin 9 Replace the bushing 3 Remount the truck and bushing on the baseplate axle H Screw on and tighten the king pin nut BEARING SET 8 Pcs EGOCRO007 T Unscrew the wheel bolt Dismount the wheel from the truck s axle 3 Replace the bearing in the wheel with the spare part by applying equal pressure on the outer rings of the bearings Mount the wheel back onto the truck axle Screw on the wheel nut and tighten THIS MANUAL IS SUBJECT TO CHANGE WITH FUTURE REVISIONS PLEASE VISIT WWW YUNEEC COM WHEEL SET WITH PRE INSTALLED BEARINGS EGOCRO006 T Unscrew the wheel bolt Dismount the wheel from the truck s axle and replace it with the replacement part 3 Screw on and tighten the wheel bolts BATTERY PACK EGOCRO14 1 Unscrew the screws connecting the battery pack to the deck Tilt the battery pack out of its slot with the ECU 3 Disconnect the wires connec ting the battery pack to the ECU and reconnect the ECU s wires to the replace ment part H Slide the replacement part in its slot with the ECU Screw in the deck screws connecting the battery pack to the deck
6. Mount the wheels back on the truck s axle and tighten the screws REAR TRUCK SET WITH MOTOR EGOCRO 2 T Unscrew the rear wheel nuts Dismount the rear wheels from the truck s axle 3 Unscrew the top screws connecting the rear baseplate to the deck M Replace the complete assembly with the replacement part and reinstall 5 Mount the wheels back on the truck s axle and tighten the screws ELECTRONIC CONTROL UNIT EGOCRO13 T Unscrew the screws connecting the ECU to the deck Slide the ECU from the battery pack 3 Disconnect the wires connecting the ECU to the battery pack H Reconnect the battery packs wires to the replacement part Slide the replacement part in it s slot with the battery pack amp Screw in the deck screws connecting the ECU to the deck MOTOR COVER EGOCR003 T Unscrew the five screws securing the motor cover Remove the motor cover and replace it with the replace ment part 3 Screw on the motor cover screws and tighten DRIVE BELT EGOCRO004 T Unscrew the drive wheel bolt Dismount the rear wheels from the trucks axle 3 Unscrew the drive belt cover screws 4 Replace the belt with the replacement part Screw on and tighten the drive belt cover screws amp Mount the drive wheel back onto the truck s axle Z Screw on the drive wheel nut and tighten E GO CRUISER CE FE X c wens FCCID 2ABBSYUNEECGSFKRX18 ICID 11554A Cruiser CAUTION DO NOT SHORT CIRCUIT DISASSEMBLE OR
7. customer service YOU CAN CONTACT THE E GO CUSTOMER SERVICE AT rUMEEC COM 18 SPARE PARTS EGOCRO001AU E GO CRUISER WITH AU CHARGER EGOCROOTEU CRUISER WITH EU CHARGER EGOCR001UK CRUISER WITH UK CHARGER EGOCROOTUS wA E GO CRUISER WITH US CHARGER EGOCR002 mia GRIP TAPE E GO CRUISER EGOCR0O03 iia MOTOR COVER E GO CRUISER EGOCRO04 waa DRIVE BELT E GO CRUISER EGOCR0O05 BUSHING SET E GO CRUISER EGOCRO06 eer WHEEL SET WITH PRE INSTALLED BEARINGS E GO CRUISER EGO CROO7 ii BEARING SET E GO CRUISER EGOCROOS wa COMPLETE HARDWARE SET E GO CRUISER EGOCRO09 u REMOTE CONTROL WITH USB CABLE E GO CRUISER EGOCROT1OAU AU CHARGER E GO CRUISER EGOCROTOEU ror sa EU CHARGER E GO CRUISER EGOCROT1OUXK iore UK CHARGER E GO CRUISER EGOCROTOUS eios US CHARGER E GO CRUISER EGO CRO 1 keiserens FRONT TRUCK SET E GO CRUISER EGOCRO 12 REAR TRUCK SET WITH MOTOR E GO CRUISER EGOCROT3 ELECTRONIC CONTROL UNIT ECU E GO CRUISER EGOCR014 sre BATTERY PACK E GO CRUISER EGOCROT15AU see CHARGE LEAD WITH AU PLUG E GO CRUISER EGOCROT5EU eese true CHARGE LEAD WITH EU PLUG E GO CRUISER EGOCROT15UMK iiem CHARGE LEAD WITH UK PLUG E GO CRUISER EGOCROT15US CHARGE LEAD WITH US PLUG E GO CRUISER EGOCR018 ise RES DECK WITH GRIP TAPE E GO CRUISER EGOCROT17 ose cs T TOOL WITH PIN TOOL E GO CRUISER 19 DECK 5
8. COMES WITH USING PERSONAL ELECTRONIC TRANSPORTER PET IT SHOULD BE CLEAR THAT READING THIS MANUAL WILL ONLY REDUCE AND NOT ELIMINATE THE RISK INHERENT TO USING PERSON AL ELECTRIC TRANSPORT IF YOU EXCEED THE ABILITY OF YOURSELF OR YOUR E GO BY RIDING OVER OBSTACLES OR ANY OTHER UNSUITABLE SURFACES THIS MIGHT POTENTIALLY LEAD TO COLLISIONS OR FALLS IN TURN LEADING TO SERIOUS OR FATAL INJURY OR THE DAMAGING OF YOUR E GO RIDERS FIRST TIME USING E GO START BY RIDING IN THE LOW SPEED MODE INEXPERIENCED RIDERS ARE BEST TO FIRST PRACTICE IN A SPACIOUS NON TRAFFIC ZONE INEXPERIENCED RIDERS SHOULD BE ASSISTED BY MORE EXPERIENCED RIDER DO NOT LET NEW RIDERS OPERATE THE E GO OUTSIDE OF YOUR SUPERVISION UNLESS THEY HAVE READ THIS GUIDE YOU SHOULD NOT ALLOW ANYONE TO STEP ONTO YOUR E GO FOR THE FIRST TIME UNLESS YOU ARE THERE TO SUPPORT THEM ASSIST NEW RIDERS UNTIL THEY ARE COMFORTABLE WITH THE BASIC OPERATION OF THE E GO RIDER PROFILE E GO IS DESIGNED FOR HUMAN RIDERS E GO IS DESIGNED FOR RIDERS 14 YEARS AND OLDER THE E GO IS DESIGNED FOR RIDERS WITH BODY WEIGHT UNDER 100 KG 220 LBS THE E GO IS NOT DESIGNED FOR CARGO TRANSPORTA TIONS E GO IS DESIGNED FOR RIDERS IN GOOD PHYSICAL HEALTH DO NOT RIDE THE E GO WHEN SICK AS WITH ANY OTHER PERSONAL ELECTRIC TRANSPORTATION DEVICE YOU MUST BE MENTALLY ALERT TO SAFELY RIDE AN E GO THE E GO IS NOT DESIGNED FOR TANDEM USE
9. M E GO WHEN CHARGING DO NOT KEEP THE BATTERY ON CHARGE ONCE IT IS FULLY CHARGED STOP USE OF THE PRODUCT OR CHARGING UNIT IF ANY WIRES ARE WORN OR DAMAGED DO NOT MODIFY THE ELECTRICAL CONTROLS OR WIRING ONLY USE MOTOR BATTERY OR CHARGING UNIT SUPPLIED OR APPROVED BY E GO DO NOT USE THE E GO S BATTERY TO POWER ANY OTHER EQUIPMENT 1H BATTERY SAFETY LITHIUM ION BATTERIES CAN EXPLODE OR CAUSE A FIRE IF THEY ARE USED INCORRECTLY OR IF THEY ARE DEFECTIVE THEREFORE YOU ARE RECOMMENDED TO READ THE FOLLOWING INSTRUCTIONS VERY CAREFULLY EACH TIME BEFORE USING THE BATTERY CAREFULLY CHECK THE BATTERY PACK AND IN PARTICULAR THE PROTECTIVE SEAL CASING TO MAKE SURE THAT IT 15 UNDAMAGED AND INTACT IF IN DOUBT TAKE THE BATTERY TO A CHEMICAL WASTE DISPOSAL FACILITY AND OR CONTACT YUNEEC CUSTOMER SUPPORT IMMEDIATELY ALWAYS HANDLE THE BATTERY WITH CARE NEVER DROP THE BATTERY STORE THE BATTERY IN A SAFE AND DRY PLACE AND KEEP THE BATTERY AWAY FROM ALL METAL OBJECTS NEVER EXPOSE THE BATTERY TO TEMPERATURES ABOVE 100 DEGREES CELSIUS ONLY USE OFFICIAL YUNEEC E GO CHARGERS THAT HAVE BEEN SPECIALLY BEEN DESIGNED FOR USE WITH LITHIUM ION BATTERIES WHEN CHARGING BATTERIES KEEP THE CHARGER AWAY FROM HIGHLY FLAMMABLE MATERIALS OR PRODUCTS AND NEVER LEAVE THE CHARGER UNATTENDED WHEN IN USE WHEN CHARGING THE CHARGER CAN GET HOT DO NOT PLACE THE CHARGER ON DAMAGABLE SURFACES IF YOU ARE NOT PLANNING ON USING THE BATTERY FO
10. O NOT RIDE THROUGH PUDDLES ALWAYS WEAR PROTECTIVE GEAR WHEN RIDING ALWAYS WEAR A HELMET WHEN RIDING USE AN APPROVED SKATEBOARD BICYCLE OR FULL FACE MOTORCYCLE HELMET THAT PROPERLY FITS WITH THE CHIN STRAP SECURELY FASTENED USE DIRECT HAND CONTACT WHEN OPERATING THE HANDHELD REMOTE WEARING GLOVES OR AN UNUSUAL GRIP MIGHT INTER FERE WITH YOUR ABILITY TO ACCURATELY USE THE CONTROLS DO NOT WEAR LOOSE CLOTHING THAT CAN GET STUCK IN THE WHEELS OR DRIVE BELT BE AWARE THAT A STRONG ELECTROMAGNETIC FIELD IN YOUR AREA MIGHT INTERFERE WITH THE FUNCTION OF THE REMOTE CONTROLLER BRAKE WHEN GOING DOWNHILL TO MODERATE YOUR SPEED TAKING ON INCLINES OVER 10 MIGHT OVERHEAT THE ECU AND CAUSE INTERMITTENT POWER LOSS OR EVEN SHUT DOWN THE ECU DO NOT RIDE E GO DOWNHILL MORE THAN 2 TO AVOID ECU OVERHEATING REGULAR SHORT BURST OF FULL POWER AND BRAKING HEAVILY WILL DRAIN THE BATTERY FASTER THAN RIDING AT A MODERATE CONSISTENT SPEED BEWARE OF WHEEL STOPS THAT CAN OCCUR WHEN THE E GO S WHEELS ENCOUNTER AN OBSTACLE OR TERRAIN CHANGE THAT PREVENT THEM FROM MOVING THIS WILL BRING THE E GO TO AN ABRUPT STOP AND ARE LIKELY TO CAUSE A FALL NEVER RIDE ON STAIRS ELEVATORS OR THROUGH REVOLVING DOORS DO NOT ATTEMPT JUMPS OR OTHER STUNTS THIS MIGHT LEAD TO INJURY OR DEATH AND MIGHT DAMAGE YOUR E GO ALWAYS BE ALERT AND AWARE OF YOUR SURROUNDINGS WHEN RIDING 13 RIDING OUTSIDE OF YOUR PRIVATE PROPERTY ABIDE BY THE LAWS AND REGULATIONS IN YOUR S
11. R ABOUT 6 MONTHS OR LONGER FIRST CHARGE IT FULLY AND THEN RECHARGE IT ONCE A YEAR THIS IS BECAUSE A LITHIUM ION BATTERY THAT HAS BEEN LEFT EMPTY FOR TOO LONG CAN NO LONGER BE CHARGED 15 TROUBLESHOOTING MY BOARD DOESN T Check if the board is activated on When turning on the board you should START hear two beeps and its status indicator light should come on Check if the controller is powered ON When turning ON the controller its blue light should start flashing If both the board and controller are powered ON and the wireless controller s green light is not flashing it means the board and controller are not syn chronized see page 10 If both board and controller are powered ON and both the controller s blue and green light are flashing but you don t hear a beep and the board does not start turn off the board and turn it on again If the board and controller are synchronized and the controller s blue light is followed by a red flashing light and vibration it means the board s battery is low and needs to be recharged If board and controller are synchronized and the controller s green light is followed by a a red flashing light and vibration it means the controller s battery is low and needs to be recharged MY BOARD IS MOVING i Check if the board is in slow speed mode If so move the controller s AT LOW SPEED speed mode switch to fast speed mode If during your ride the controller s blue light is flashing foll
12. S THAT RECYCLES POWER USED WHEN BRAKING TO RECHARGE THE BATTERY BE AWARE THAT RBS STOPPING PERFORMANCE VARIES DEPENDING ON RIDER WEIGHT AND CONDITIONS AT JUST 6 3 KG 13 9 LBS THE E GO IS LIGHTWEIGHT AND PORTABLE WHICH WORKS IN COMBINATION WITH AN ARRAY OF PUBLIC TRANSPORTATION 10 PERFORMANCE Max User Weight 100kg 220bs Max Range 18mi 30km High Speed Mode Max 12 5mph 20km h Low Speed Mode Max 8mph 13km h CHARGER Input AC 100 240V 50 60HZ 1 5A Max Output 29 5V 2A Charge Indicator Red when charging Green when charged CONTROLLER Material ABS Plastic Dimensions 125 41 33mm Weight 609 Battery Type Lithium Battery Capacity 240mAH Battery Charging Time 50 minutes Wireless Connection 2 4GHz Vibration Yes BOARD Deck Material Canadian Maple Wood Deck Dimensions 960 240mm Wheel Material Polyurethane Wheel Size 90mm diameter 52mm width Battery Type Li ion Battery Capacity 7 8 AH Battery Cell Quantity 21 pcs Battery Charging Time 3 5 hours depending on ambient temperature Motor Type Brushless Direct Current Motor Power Max 400W Ave Power 150W Transmission Model Synchronous Belt Drive Board Weight 13 9165 6 3kg sSPECFICATIONMS 11 SAFETY WARNINGS AND TIPS ABOUT THE SAFETY GUIDELINES BEFORE RIDING THE E GO IT IS STRONGLY ADVISED TO READ THROUGH AND FOLLOW ALL TIPS INSTRUCTIONS AND WARNINGS LISTED UNDERNEATH THIS CAN REDUCE THE RISKS THAT
13. TATE OR COUNTRY RESPECT OTHER DRIVERS AND PEDESTRIANS ON THE ROAD AVOID RIDING ON BUSY ROADS AND CROWDED AREAS ADJUST YOUR SPEED WHEN RIDING ON THE SIDEWALK DO NOT PARK YOUR E GO IN A WAY THAT BLOCKS PEOPLE OR TRAFFIC AS IT CREATES A SAFETY HAZARD CROSS ROADS AT DESIGNATED CROSSWALKS OR SIGNALED INTERSECTIONS DO NOT JAYWALK RIDE WHEN RIDING WITH OTHER E GO RIDERS YOU SHOULD KEEP A SAFE DISTANCE FROM EACH OTHER AND OTHER TRANSPORT DEVICES WHEN RIDING WITH OTHER E GO RIDERS YOU SHOULD NOT RIDE SIDE BY SIDE UNLESS THERE IS PLENTY OF ROOM LEFT FOR PEDESTRIANS AND OTHER POTENTIAL TRAFFIC IDENTIFY AND KEEP A SAFE DISTANCE FROM HAZARDS AND OBSTACLES ON THE ROAD DO NOT RIDE YOUR E GO ON PRIVATE PROPERTY INSIDE OR OUTSIDE UNLESS YOU HAVE OBTAINED PERMISSION TO DO SO MAINTAIN CONTROL OF YOUR EQUIPMENT STORAGE AND MAINTENANCE DO FREQUENT MAINTENANCE CHECKS BEFORE RIDING MAKE SURE ALL SCREWS ARE TIGHT AND YOUR E GO IS IN PERFECT WORK ING ORDER CLEAN THE BOARD S BEARINGS REGULARLY TO CLEAN THE WHEELS IT IS ADVISED TO REMOVE THEM FROM THE AXLE TURN OFF E GO AND WIRELESS CONTROLLER WHEN NOT IN USE CHOOSE A COOL ENVIRONMENT FOR STORING THE E GO AND ITS CHARGER KEEP YOUR BATTERY FULLY CHARGED WHEN NOT IN USE RECHARGE THE BATTERY IN A WELL VENTI LATED AREA DO NOT RECHARGE THE BATTERY IN AN AREA THAT MIGHT ALLOW E GO OR ITS CHARGING UNIT TO BECOME WET DO NOT LEAVE E GO CHARGING UNATTENDED KEEP CHILDREN AWAY FRO
14. in clines greater than recommended If during your ride the board stops and the controller s blue light is flashing one to four times followed by four yellow flashes and is accompanied by vibration this indicates a motor malfunction Please check if the motor plugs are tightly is well connected to the lead of the battery compartment If after this the board stops again please contact the E GO customer service 17 If during your ride you hear beep the board stops and only the controller s blue light is flashing it means the control signal is lost Turn the controller off and then on again to reconnect Control signal loss will occur when the distance between your board and controller becomes too great To reconnect close the distance between the two MY BOARD DOESN T Check if the charge cable is connected to the board and if the charger is connected to a standard A C power source If the connection is good and CHARGE the board is charging the charger s battery status indicator will turn red When fully charged it should turn green In any other situation please contact the E GO customer service MY CONTROLLER I Check if the USB cable is well connected to the controller and the charge DOESN T CHARGE port and if the board is powered on If the connection is good and the controller is charging the controller s red light will turn on When fully charged the red light will turn off In any other situation please contact the E GO
15. n and stability on an array of 6 into H reliable urban transport system kingpin nut baseplate nut SS axle nut THE TRUCKS Connecting the wheels to the deck are two alloy trucks made of the highest grade materials available The trucks can be adjusted using the truck tool For more on the truck tool see page 7 THE CONTROLLER A key feature of the E GO is without doubt its sleek pocket sized wireless controller which allows you to intuitively control its movements by simply sliding the throttle brake 7 up and down The battery status indicator s light 9 indicates the wireless controller s and board s battery status Green light indicates the board s battery status Blue light indicates the controller s battery status Each light blinks 1 2 3 or 4 times in series Each blink indicates 2596 of the total battery capacity When the board or controllers battery goes under 2596 of its maximum capacity the controller vibrates its light will turn red and blink 1 time When charging with the control ler connected to the board a red light indicates that the controller s battery charge is less 100 Example when activated but not charging the board s battery is completely empty and the controller s battery has less than 7596 of its full charge capacity left 1 red blink will be followed by 2 blue blinks For more information on the yellow and purple warning lights
16. owed by a red flashing light and accompanied by vibration it means the board s battery is low and needs to be recharged MY BOARD STOPS AUTOMATICALLY If during your ride the board stops and the controller s blue light is flashing followed by a red flashing light and accompanied by vibration it means the board s battery is low and needs to be recharged If during your ride the board stops and the controller s green light is flashing followed by a red flashing light and accompanied by vibration it means the controller s battery is low and needs to be recharged If during your ride the board stops and the controller s blue light is flashing one to four times followed by one yellow flash and is accompanied by vibration it means the board s ECU has overheated Let it cool down for ten minutes and retry If after this the board stops again please contact the E GO customer service If during your ride the board stops and the controller s blue light is flashing one to four times followed by two yellow flashes and is accompanied by vibration it means the board s battery has overheated Let it cool down for 10 minutes and retry If after this the board stops again please contact the E GO customer service If during your ride the board stops and the controller s blue light is flashing one to four times followed by three yellow flashes and is accompanied by vibration it means the board has been overloaded or is being used on
17. switching the power switch on The board should now beep two times and its battery status indicator should be flashing fast Slide down the wireless controller s throttle brake to the lowest possible position and hold it there At the same time press and release the start button while the throttle brake is still held down After 7 seconds the controller will show 8 green flashes followed by blue flashes At this point release the throttle brake The board should now beep again indicating a successful synchronization Q FEATURES THE E GO FEATURES 2 SPEED MODES SLOW MODE OR BEGINNER MODE WITH LIMITED SPEED OF 13 KM H OR 8 MPH AND A FAST MODE WITH A MAXIMUM SPEED OF 20 KM H OR 12 5 MPH THE E GO ALSO FEATURES 2 RIDING MODES THE ECO MODE WITH LOWER ACCELERATION CURVE AND THE SPORT MODE WITH A HIGHER ACCELERATION CURVE RIDING IN ECO MODE WILL DEMAND LESS POWER FROM THE BATTERY THUS MAXIMIZING THE EGO S RANGE THE E GO WILL TAKE YOU UP INCLINES OF UP TO 10 FOR A LIMITED DISTANCE VARIABLES LIKE WEIGHT OF RIDER INCLINE AMBIENT TEMPERATURE AND ROAD SURFACE MAY CAUSE THE ECU TO OVERHEAT AND PERFORM TEM PORARY CONTROLLED SHUTDOWN TO FULLY CHARGE THE E GO S BATTERY CHARGE TIME OF 3 TO 5 HOURS FROM STANDARD A C POWER SOURCE IS NEEDED TO FULLY CHARGE THE WIRELESS CONTROLLER CHARGE TIME OF ABOUT 50 MINUTES FROM ANY USB PORT IS NEEDED THE E GO FEATURES REGENERATIVE BRAKING SYSTEM RB
18. t and distinguishes itself as such through features such as its advanced braking system giving the rider more control over his her vehicle which is required to ensure the safety of other people as well as his her own Keeping the latter in mind we would like to suggest you read through this users manual to ensure you understand fully how to properly set up and use your E GO and what general common sense to apply when riding in a public area The general rule to follow Ride with consideration and style We hope you enjoy your E GO experience GEAR THE DECK The E GO features 13mm eight layered composite wood deck making it flexible durable and strong all the qualities a rider looks for in board The deck surface is finished with griptape to avoid slipping THE BATTERY E GO s sleek low profile multi cell battery pack is located under the deck and utilises Yuneec s latest patented battery technology Its flexible battery casing allows the deck to bend while riding charge port 2 power switch 3 power status indicator 4 USB port S 5 2 4GHz bluetooth switch Electronic Control Unit ECU THE MOTOR By integrating technology developed by Yuneec for use in the aviation industry the brushless 400 watt motor provides reliable and efficient power for your E GO THE WHEELS The E GO s 90mm wheels surfaces turning the E GO bearing x provide tractio
19. the E GO and the controller s battery in 3 to 5 hours depending on charge left and ambient temprature giving you a maximum riding range of 30 km 18 miles depending on weight road conditions riding style etc THE PIN TOOL Also included with the E GO is a small pin shaped object which allows you to access the speed mode switch on the controller and the bluetooth switch on the the board CHARGE SETUP The board needs to be power ed on in order to charge the wireless controller through the usb port Charge lead depending on sales area To ensure a healthy battery life recharge the battery for 6 hours straight before first use This will condition the battery and give better long term performance S rNCING CONTROLLER AND BOARD Use the pin tool page 8 to slide the speed switch positioned on the left side of the controller fully down Begin with the BLUETOOTH switch flipped toward the right closest to the motor Immediately after powering the board ON move the BLUETOOTH switch to the left furthest away from the motor and back to the right closest to the motor Then the battery status indicator should go from flashing fast to flashing more slowly Slide down the riding mode switch Make sure the BLUETOOTH switch ill 4 is positioned on the left side of the wireless switched to the side closest to the motor controller to ECO mode then turn on the board by

Download Pdf Manuals

image

Related Search

Related Contents

report - Student Projects  COBY electronic NBPC1028 User's Manual    Sony WEGA KLV-17HR1 17 in. LCD Television  Mode d`emploi 555 610  Bartsch  neMESYS Handbuch Hard  Manual – equipamentos  /é January 2015  Hiver 2007, volume 9 - Syndicat de Champlain  

Copyright © All rights reserved.
Failed to retrieve file