Qccess Air@-EL300
Contents
1. special attention in handling bracket to avoid injuries from sharp edges Please use safety gloves Air EL Series Names of Components Optical Lens Body Permanent magnetic base 4 Screw knobs for adjusting body angle DC Power Input UTP Cable Connector for DVR Receiver Only Signal Indicator Green LED Power Indicator Red LED RCA Connector Transmitter Video Input Receiver Video Output 00 60080 How to install Air EL Series under the elevator car Transmitter Receiver Mounting Bracket Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Move the elevator car to the lowest position where it is easy to work under the outer surface of the bottom of the elevator car Install CCTV camera inside the elevator car Run video coaxial cable and the Transmitter power cable along the exterior wall of elevator car Use a conduit from CCTV camera to the Transmitter to avoid any friction or damage The power of CCTV camera must be connected according to the camera specifications Place the Transmitter with magnetic base on the bottom of shaft Connect video coaxial cable to the Transmitter Position of the Receiver and the Transmitter must be well planned before the installation Connect the power cable to the Transmitter Confirm that the Laser light is emitted Adjust the diameter of circular reflection on floor where the Receiver will be installed Use the weig2. C FE User Manual and Installation Guide Air EL Series Air EL150 Air EL300 Laser Optical Video Transmission system for Elevator CCTV DANGER AVOID DIRECT EYE EXPOSURE AVOID POINTING THE LASER AT PEOPLE OR AIRCRAFT Qc C ess Air EL is a Trademark of Qccess Co Ltd htto www qccess com Made In Korea What is in the box Laser Optical Laser Optical 2 AC DC Power Adapters Mounting Bracket Video Transmitter Video Receiver AC 100 240V 50 60Hz 0 3A for the Receiver Output DC 12V 1A Safety Warning 1 Air EL Series is a laser device DO NOT STARE AT THE LASER WARNING LIGHT DIRECTLY or through the optical system when the device Is on It may be harmful to your eyes 2 Air EL Series is a precise optical device Installation requires professional knowledge Please consult with a professional who has knowledge and experience in elevator and CCTV for maintenance 3 Elevator safety is critically relevant to human life When installing Air EL Series pay special attention to elevators operation mechanism Passenger access MUST be restricted or prohibited until the installation is completed Any problems in wiring Sensors and switches can result in safety accident including death 4 Air EL Series is not water proof Do not place the transmitter and receiver on wet surface or near the water Rain snow or humidity can damage the equipment 5 Air EL Series comes with a mounting bracket made of metal Pay
3. e user will be required to correct the interference at his own expense Warning Changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment
4. ht and 4 corner screws to fine tune the angle Laser light reflection must be a circular shape not oval Shape Using the Laser light reflection as guide install the metallic Mounting Bracket on the floor The Mounting Bracket and the Receiver should be olaced in the center of the Laser light reflection Place the Receiver on the Mounting Bracket Use the leveler and 4 corner screws to make the Receiver horizontal Step 7 Connect the power cable to the Receiver Use field monitor to test video transmission Check the condition of video quality while moving the elevator up floor by floor If you notice any video noise or disruption adjust the angle of Receiver with 4 corner screws The alignment between Transmitter and Receiver must be corrected until the video transmission is good at the highest floor Repeat adjustment until good video quality is confirmed at all floor levels Step 8 After fine tuning of the alignment is complete connect the coaxial cable from the Receiver to DVR or display equioment in control room If the DVR supports UTP use UTP cable to connect the Receiver to the DVR Test video monitoring during a regular elevator operation Optical axis alignment method between Transmitter and Receiver It is extremely important to align optical axis between the Transmitter and the Receiver for optimal image transmission since Air EL Series is an image data transmission device which uses Laser light The Receiver needs t
5. lens has excessive amount of dust Check the optical axis alignment between the Transmitter and the Receiver again Dust on the Receiver Check CCTV camera and power adapter first Check power adapter of the Air EL Series Check the power indicator and signal indicator on the Transmitter and the Receiver of Air EL Series It is recommended to clean the lens during the safety Inspection lens Use a camera lens cleaning brush and do not touch the Receiver body EtC Please consult with the distributor for further technical assistance FCC Verification This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Information to the user This equipment has been tested and found to comply with the limits for a Class A digital device oursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equioment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used In accordance with the instruction manual may cause harmful interference to radio Communications Operation of this equioment in a residential area is likely to cause harmful interference in which case th
6. o be installed where the center of the Receiver lens can be aligned with the center of the Laser light circle from the Transmitter Please follow the Alignment Instructions How to install Air EL Series above the elevator car Step 1 Step 2 Mounting Bracket Receiver Step 3 Transmitter Step 4 Step 5 Step 6 Move the elevator car to the highest position where it is easy to work on the outer surface on the roof top of the elevator car Install CCTV camera inside the elevator car Run video coaxial cable and the Transmitter power cable through the elevator roof top Use a conduit from CCTV camera to the Transmitter to avoid any friction or damage The power of CCTV camera must be connected according to the camera specifications Place the Transmitter with magnetic base on the roof top of the elevator car Connect video coaxial cable to the Transmitter Position of the Receiver and the Transmitter must be well planned before the Installation Connect the power cable to the Transmitter Confirm that the Laser light is emitted Adjust the diameter of circular reflection on the ceiling where the Receiver will be installed Use the 4 corner screws to fine tune the angle The Laser light reflection must be a circular shape not oval shape Using the Laser light reflection as guide install metallic Mounting Bracket on the ceiling The Mounting Bracket and the Receiver should be placed in the center of
7. ptical Axis alignment between the Transmitter and the Receiver 4 Screw knobs Magnetic base Warranty I 1 The limited warranty period of Air EL Series is 3 years from the date of purchase 2 This warranty does not apply to a Products subject to abnormal use or conditions accident mishandling neglect Unauthorized alteration misuse improper installation or repair or improper storage bo Products whose label has been removed altered or defaced c Damage from exposure to excessive moisture humidity temperature d Products damaged from external causes such as fire flood sand theft or improper usage of any electrical source Specifications Data Format VO Signal Video Format S Video NTSC or PAL Composite CVBS Max l Wome 7S Ohi Transmitter 250g Bit Error Rate lt 10 Light Source inGaAIP Laser Diode Laser Wavelength 658nm Output Power 30mW Beam Divergence 18mrad Receiver 2579 Detector Silicon Pin PD of Air EL150 Diameter 5mm Gain gt ABM Receiver 257g Detector Si APD of Air EL300 Diameter 5mm Gain gt 45d0dBm Power Supply Input AC 100 240V 50 60Hz Output DOAN TA Operating Temperature Dimensions How to solve a problem Symptoms If there is no image on the monitor or No Signal on the DVR monitor If severe noise appears on the screen 4 158 F 20 70 C 3 9 x 3 9 x 5 5 inches W D H Troubleshooting Check CCTV camera Check if the Receiver optical
8. the Laser light reflection Place the Receiver on Mounting Bracket Use the leveler and corner screws to make the Receiver horizontal Step 7 Connect the power cable to the Receiver Use the power outlet in the mechanical room for Receivers power supply Usually there are holes between the mechanical room and elevator hoist way Use a conduit for running power cable from mechanical room to the Receiver on the ceiling Step 8 After fine tuning of the alignment is complete connect the coaxial cable from the Receiver to DVR or display equipment in control room If the DVR supports UTP use UTP cable to connect the Receiver to the DVR Step 9 Test video monitoring during a regular elevator operation Using field monitor to test video transmission check the condition of video quality while moving the elevator down floor by floor If you notice any video noise or disruption adjust the angle of Receiver with 4 corner screws The alignment between the Transmitter and the Receiver must be corrected until the video transmission is good at the lowest floor Repeat adjustment until good video quality is confirmed at all floor levels Recommended Operational Distance Elevator s running distances Air EL150 max up to 150m 495ft Air EL300 max up to 300m 990ft Good Alignment Bad Alignments Transmitter Laser Beam Fine adjustment for alignment Use 4 screw knobs on the magnetic base for fine adjustment of the o
Download Pdf Manuals
Related Search