Bugatti Italy Vera
Contents
1. 17 Always ensure that you pour out boiling water slowly and carefully taking care not to tilt the spout too rapidly 18 To prevent burns avoid to opening the lid when the water is being boiled or just after the kettle has switched off Be careful when opening the lid if the kettle is still hot and you wish to refill it with water Boiling water can cause burns 19 Move the appliance with extreme care when it contains hot water CAUTION Do not move the kettle while is switched on 20 Only clean the appliance using a damp cloth when it has cooled down 21 To disconnect verify that the kettle is switched off and remove plug from wall outlet Always unplug the appliance by holding the plug not the cord 22 Unplug the power cord from the wall outlet when the kettle is not in use and before cleaning Allow the kettle to cool before cleaning it 23 Note Remove plug from wall outlet when you are not using the kettle Always unplug the appliance by holding the plug not the cord 24 CAUTION To prevent damages to the appliance do not use alkaline cleaning agents when cleaning use a soft cloth and a mild detergent For conversion table for Fahrenheit and altitude s temperature difference see the inner cover 20 Installation and starting up The original packaging has been designed for dispatch by post Keep it in case you need to return the kettle to the supplier Before installing the kettle comply with all the points of the s2. 5 is well connected to the wall socket Check that there is electricity in your system Remeber before operating the kettle please fully charge the battery for 12 hours Make the RESET function for the display as per Special instruction of this manual Make the RESET function for the display as per Special instruction of this manual and if the problem does not leave make the descaling as per point b of the Cleaning and maintenance chapter Make the descaling as per point b of the Cleaning and maintenance chapter We suggest to change the residual water after each boiling cycles Rinse the kettle sufficient time in order to remove completely the descaling product Fill the kettle with water till on the display the blue light of the level ml minimum stop to blink and the blue light of the level 800ml is on Have a look to the third cover page instruction ALTITUDE WATER BOILING TEMPERATURE during the BOIL FUNCTION For conversion table for Fahrenheit and altitude s temperature difference see the inner cover ARRANTY 1 Awarranty is deemed to be the replacement or repair free of charge of the parts making up the kettle that were faulty at the time of purchase due to manufacturing faults 2 In the case of irreparable or repeated faults which are due to manufacturing faults as above at the amp manufacturer s sole discretion the machine will be replaced 3 The warranty does not cover damage due t
3. IONS CAREFULLY 1 TO PREVENT SERIOUS INJ URIES ELECTRIC SHOCKS AND FIRE TO PEOPLE DO NOT IMMERSE CORDS PLUGS POWER BASE OR THE KETTLE ITSELF IN WATER OR OTHER LIQUIDS EITHER PARTIALLY OR TOTALLY WARNING DANGER OF BURNS PAY ATTENTION TO HOT SURFACES Do not touch hot surfaces Use only the handle to pick up the kettle Use an oven glove when touching hot parts such as body 4 lid 1 and all surfaces of the kettle DANGER OF BURNS 2 The kettle has been designed for HOU SE HOLD U SE ONLY Use kettle only for its intended use Do not make any technical modifications that might cause risks 3 Close supervision is necessary when any appliance is used near children The appliance can be used by children aged from 12 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use the appliance in a safe way and understand the hazards involved 4 Never touch live electrical parts They may cause electric shocks and serious personal injury Connect the power base unit 5 to a wall socket having the appropriate voltage The voltage must correspond to the voltage indicated on the rating plate underneath the kettle 4 Make sure that the socket that you are using is earthed F Do not use the kettle with bare or wet feet 5 Figure A power cord with plug A short power cord with plug is supplied to reduce the risk of becoming
4. Manuale d istruzioni Owner s Guide Manuel d instructions Bedienungsanleitung Instrucciones para el uso Manual de instru es Gebruiksaanwijzing VHCTpyKUMA NO MpuMeHeHuto Navod k pouziti Manual de instructiuni Kayttoohjeet Brugsanvisning DAHTMEZ XPH2H2 Instukcja obslugi Kullanma kilavuzu H Pf Fa Tia BUGiZANW UU o oe IMPORTANT NOTICES Dear Customer thank you for choosing Vera the electronic kettle from Casa Bugatti Like any domestic appliance this kettle must be used with care and attention to prevent people getting burnt and the kettle getting damaged BEFORE USING THE KETTLE FOR THE FIRST TIME READ ALL THE INSTRUCTIONS ON INSTALLATION USE AND MAINTENANCE AND THE SAFETYINSTRUCTIONS CAREFULLY DO NOT USE THE KETTLE UNLESS YOU ARE THOROUGHLY FAMILIAR WITH THE INSTRUCTIONS WARNING No liability is accepted for damage due to incorrect use or use other than for its intended purpose using the kettle continuously without any water repairs carried out by unauthorised persons use of non original spare parts or accessories plug in Vera kettle in a non earthed socket Instruction for use For further information or in the event of problems that have not been sufficiently addressed in these instructions contact Customer Care at CASA BUGATTI SAVE THESE INSTRUCTIONS CAREFULLY ani remember to pass them on to those who will use the kettle after you If t
5. afety instructions on the previous pages After removing the kettle from its packaging make sure that it is in perfect condition and make sure that no kind of matter packaging material warranty sheets or the like have accidentally fallen inside the kettle during transport or when opening the packaging The plastic bag in which the kettle is packaged should be kept out of reach of children as it poses a suffocation hazard In order to remove dust that may have accumulated on the kettle simply dust it off with a dry soft cloth After you have carried out the above steps and have strictly followed the safety standards proceed to connect to the power supply Connecting to power supply electric current can kill Follow safety instructions Plug the power cord 6 of the Vera kettle into a power socket the voltage of which corresponds to the voltage indicated on the rating plate underneath the kettle To disconnect make sure that the kettle is not running and if it is running press the on off button 14 to stop all the heating operation Do not unplug the kettle from the power point by pulling on the cord Always unplug the appliance by holding the plug 6 The Vera kettle will show that it is connected to the power when the display is on To switch off completely the kettle plug 6 has to be removed from the socket Make sure that the electric socket that you are using is suitably earthed Never use faulty or damaged power cords Use an extens
6. emperature difference see the inner cover 22 Advice and recommendations on use Heating Boiling function a Place the kettle on the power base unit 5 and press the on off button 14 When the kettle starts boiling heating the temperature symbol mark C Celsius Degrees is on and the number grow up showing on the display the average temperature of the water inside the kettle b When the kettle is heating the segments 9 on the display 2 runs clockwise this indicates that the kettle is working and is ON c When the water temperature reaches 100 C the kettle switches off automatically and the boil word 10C flash on the display 2 for about 10 seconds then the display change to show the current average water temperature C inside the kettle d At any time the function boiling water can be stopped by pressing the On Off button 14 ATTENTION If the button on off is pressed two times consecutively after the boil function the kettle will restart again to boil only after the display shows the temperature of 95 C e POURING OUT WATER Remove the kettle from the power base unit 5 holding it by its handle 3 Ensure that the kettle body remains level while lifting it from the power base unit 5 Pour the water from the spout with the lid 1 closed ATTENTION boiling water can cause scalds Always ensure that you pour out boiling water slowly and carefully taking care not to tilt the sp
7. entangled in objects to prevent people for tripping over it and to prevent the cord from wrapping around a longer cord Long detachable power cords or extension cords are available but they may be used only if a QUALIFIED ELECTRICIAN can confirm that they comply with wiring regulations DO NOT USE plug socket adapters If a long detachable power cord or extension cord is used For conversion table for Fahrenheit and altitude s temperature difference see the inner cover 18 IMPORTANT SAFEGUARDS a The electrical rating of the detachable power cord or extension cord should be at least as great as the electrical rating of the kettle indicated underneath the kettle itself b The extension cord must be of the 3 wire pole type and must be earthed Along cord or extension cord must never protrude from furniture or over counter tops or table tops where it may be pulled on by children or tripped over c Do not place kettle or cords on or near a hot gas ring or electric hotplate or in or near the oven d Do not use outdoors Do not let the cords hang over the edge of the table or counter or touch hot surfaces Do not operate the kettle with a damaged cord or plug or after the appliance develops faults or has been damaged in any manner Return appliance to the nearest authorized service facility for examination or repair The use of accessory attachments not recommended by the appliances manufacturer may result in fire electric shock or serious injurie
8. er 12 hours charge we suggest to reset the panel by pressing the reset buttons on the back of the handle following the steps shown into the SPECIAL INSTRUCTION paragraph at point C When take off the kettle from the power base 5 the kettle will de activate all functions shows the water level the time and the P preset function if it is activated ols 3 Sja a ES 8 3 paw uw Dl eee JM U mana alee M N N ogo a Y E o OLA v Pa u 5 When the plug 6 of the power base unit 5 isinserted into the socket Vera Display will illuminate The display indicates the clock and the water level ml minimum will flash to inform the user that the kettle is empty at the minimum level under 800ml the kettle needs to be filled by water 6 Filling the kettle a remove the kettle body from the power base unit Hold it by the handle 3 b open the lid 1 press on the rubber point picture a on the lid 1 and press down firmly tl n picture b Then release picture c and the lid will open automatically The lid is not removable and the max opening is shown in the picture d c fill the kettle with water directly under the tap or fill it by pouring water from a bottle jug or jar to the needed level attention the minimum level that allow the kettle to operate is 800 ml Do not add water past the maximum fill level On the display 2 in the water level sector 11 t
9. ettle s original packing for dispatch Important If the nonconforming product is to be serviced by someone other than contact an authorised BUGATTI dealer please remind the service to call our Consumer Service Center to ensure that the problem is properly diagnosed the product serviced with the correct parts and to ensure that the product is still under warranty DISPOSAL OF THE PRODUCT IN CONFORMITY TO EUROPEAN DIRECTIVE 2002 96 EC mmm At the end of its working life the product must not be disposed of alongside urban waste It can be delivered to local authority separated waste collection centres or to dealers who provide this service Separated disposal of a household appliance enables possible negative consequences for the environment and health arising from improper disposal to be eliminated and enables the materials of which it is made to be recovered in order to make significant power and resource savings The symbol of a moveable waste bin marked with a cross displayed on the product indicates that as a household appliance it must be disposed of separately For conversion table for Fahrenheit and altitude s temperature difference see the inner cover 28
10. he instructions are lost before you use the kettle request the instruction booklet from Customer Care at CASA BUGATTI or send an e mail to diva casabugatti it or download it from www casabugatti it PFI A On the first page of the cover you will find a gt gt B ttt m the illustrations relating to the text Keep Bis a the first page open as you read the gt instructions on use i HAS 15 For conversion table for Fahrenheit and altitude s temperature difference see the inner cover Conversion table 4 Contents Celsius Fahrenheit 0 C o F o C 0 F Pag 17 Technical features 45 113 0173 163 4 46 114 8 74 165 2 Pag Description of kettle parts 47 116 6 75 167 0 48 118 4 76 168 8 i 49 120 2 77 170 6 Pag Kettle Function 50 1220178 1724 51 123 8 79 174 2 Pag 18 20 Important safeguards 52 125 6 80 176 0 53 127 4 81 177 8 54 129 2 82 179 6 Pag 21 Installation and starting up 55 1310183 1814 56 132 8 84 183 2 Pag 21 25 Advice and recommendations on use 57 134 6 85 185 0 Pag 21 22 a T868 Pag 23 60 140 0 88 190 4 Pag 23 24 61 141 8 89 192 2 Pag 23 24 2 ae 90 194 0 Pag 25 a E Pag 25 65 149 0 93 199 4 66 150 8 94 201 2 Pag 26 Cleaning and maintenance 67 152 6 95 203 0 68 154 4 196 204 8 69 156 2 97 206 6 Pag 27 Troubleshooting 70 1580198 208 4 71 159 8 99 210 2 Pag 27 28 For conversion table for Fahrenheit and altitude
11. he water level is shown by the level lights The blue levels are ml mimimum between 0 and 800ml 800ml about 22 oz 1250ml about 35 oz 1500ml about 40 oz and the red level is 1750ml about 470z While the kettle is being filled with water the lights will illuminate one after the other as each level is reached If the water inside the kettle is over 1750ml about 470z and less than 1950ml about 540z only the top red light level is illuminate If the water level is over 1950ml about 540z the top red light level starts to flash showing that the kettle is over filled and the kettle will not operate If the water level is under then 800ml about 220z the blue ml minimum light level will be blink showing that the kettle is nearly empty In this case for safety reason and heating element protection the kettle will not operate because the water level is too low check and eventually fill the kettle with water till on the display the blue light of the level ml minimum stop to blink and the blue light of the level 800ml is on Only in this way the kettle can start to operate In case the battery is not charged or does not work the water level sectors 11 are not shown on the display 2 ATTENTION to avoid to overfill of water the kettle make sure that never the water level is over the mark 8 inside the kettle CAUTION Do not move the kettle while is switched on For conversion table for Fahrenheit and altitude s t
12. heats Should the kettle ever boil dry during operation you must leave it to cool for 10 minutes before refilling it with cold water Pull up the kettle from the power base after cooling down The safety cut off will reset automatically once the kettle has cooled B Before using Vera kettle Clean the inside of Vera kettle before using it for the first time by filling it completely to the MAX level with water boiling the water following the BOILING FUNCTION and then discarding the water Repeat this operation two times and any time that the kettle has not been used for long time C Display reset If the display is not showing correctly the functions need to be reset This is for safety to refresh all MCU memory inside Place the Vera kettle on the power base unit 5 Plug it in Press the reset button 18 by using a part of a metal clip or by toothpick for 5 seconds The display will be back to the original settings and all pre set settings clock timer and temperature will be lost A8 25 For conversion table for Fahrenheit and altitude s temperature difference see the inner cover Cleaning and maintenance CAUTION Always disconnect the kettle from the electrical outlet before cleaning Before cleaning be sure the kettle is cold g Clean the exterior surface of the kettle with a clean damp cloth to preserve its original highly polished finish Dry and polish with a soft cloth Do not use abrasive cleansers or scou
13. ion cord only after making sure that it is in perfect condition adhere strictly to the safety instructions specified in point 5 Never allow parts carrying live voltage to come into contact with water it may cause a short circuit follow all the safety instructions specified on page 4 point 3 and page 5 points 6 13 15 Advice and recommendations on use Setting up the kettle and battery back up 1 the Vera Kettle is an electronic kettle and all functions are controlled by the Controls on the handle The functions selected are shown on the Display Panel on the handle 3 a The display shows the water level b Use the controls to set the temperature of the water needed c Use the controls to set the timer You can heat water to be ready at a pre set time d The display panel has a clock 2 Follow all safety and operating instructions specified in this manual 3 Place the power base unit 5 and kettle 4 on a stable flat surface which is not hot and do not place near a heat source The surface must be dry Keep the appliance and its cord out of reach of children During use do not place the base unit on a metal tray or a metal surface 4 Vera kettle is fitted with a back up battery to remember your settings Before operating the kettle please fully charge the battery for 12 hours For more information see page 12 point c 21 For conversion table for Fahrenheit and altitude s temperature difference see the inner cover Aft
14. liminate the fault by following the instructions in this manual contact Customer Care at CASA BUGATTI Repairs carried out incorrectly expose the user to grave danger No liability is accepted for damage or injury caused by repairs carried out incorrectly and in such cases warranty rights are voided Trouble The display on handle doesn t switch on Il display does not show proper information The watel level light are on without water inside the kettle The kettle does not work properly or stops before boiling If the water tastes bad The kettle after pressing the button on off 14 does not start to heat The water inside the kettle during the heating comes to the boil but the 2mperature shown on the display on the handle is lower than 99 C 27 Possible Cause is not well positioned on the power base 5 and the plug 6 is not well insert in the socket The rechargeable battery is still not correctly charged The kettle does not work for long time There is lime scale on the water level sensors There is lime scale into the kettle Water is in the kettle for more then 12 hours The kettle is not well washed after the descaling cycle The water level inside the kettle is lower than 800ml and the blue light ml minimum on the display on handle blinks The kettle is used at an altitude over 500 1000 meter on the sea level Solution Check if the plug 6 of the power base
15. n will be off see the point o at the end of this paragraph I when the kettle is heating the segments 9 on the display runs clockwise It indicates that the kettle is working and it is ON m To cancel reset the setting program boil heat temperature and timer press the setting button A for 3 seconds The red P icon will be off Then by pressing the on off button Vera kettle starts to boil the water see the BOILING FUNCTION n To turn the display on clock 10B or temperature 10A press one time the setting button A 16 This operation can be done when the Vera kettle is not heating or boiling o ATTENTION The timer temperature function is not a permanent function For safety reasons the setting timer temperature function has to be set each time the kettle is used The water temperature shown on the display correspond to an average temperature of the water inside the kettle Tolerance 3 C For conversion table for Fahrenheit and altitude s temperature difference see the inner cover 24 Advice and recommendations on use Clock setting The Clock setting 24 hours can be set when Vera does not heat or boil water Place Vera on the power base unit 5 and set the time very easily by following these simple steps a Press the mode button 15 for 3 Seconds until the icon and hour numbers on the display start flashing b Press the setting button A 16 to set the h
16. o a incorrect or faulty use b defects caused by accidental breakages or carelessness c failure to follow instructions and warnings incorrect installation cleaning and maintenance d maintenance and or modifications performed by unauthorised personnel e use of non original spare parts f carriage g using any kettle function without water continuously h any other circumstance that cannot be ascribed to manufacturing faults Any claims not envisaged by law are excluded 4 The warranty does not cover damage due to improper use and in particular due to non domestic use 5 The manufacturer accepts no liability for any direct or indirect harm or injury to persons things and domestic animals that may arise from failure to abide by all the safety instructions contained in this manual especially failure to abide by the instructions on installation use and maintenance of the kettle 6 Replacement or repair shall not extend the warranty period The warranty does not cover the replacement of consumables such as the resistances battery etc 7 The warranty runs from the date of receipt of evidence of purchase and of receipt of the warranty card by CASA BUGATTI SERVICE CENTRE In the event of a kettle fault contact an authorised BUGATTI dealer who will return the kettle to the manufacturer The purchaser is responsible for all carriage and or dispatch costs for all repairs covered or not covered by warranty If possible keep the k
17. ons on the descaler package By the way BUGATTI suggests the following natural way if acommercial descaler is not available fill the kettle with 500 ml 16 90 US oz 17 59 UK oz white vinegar and 500 ml 16 90 US oz 17 59 UK oz water Use a soft brush together with vinegar to clean the plastic water level sensor holder in order to remove the chalky deposit Bring the vinegar to a boil You may need to repeat this several times with cooled vinegar to remove the calcium build up completely When the descaling process is complete empty the kettle and rinse out several times with clean water c Battery The battery can be removed and replaced by user because it is placed inside the handle 3 The battery life is over 2 years After that period the battery still has 70 capacity When the display 2 cannot stay ON while the kettle 4 is removed from the power base 5 means that the battery has reached its minimum level capacity Contact an authorised Bugatti Customer Service Center in order to change the battery the service center will send you the battery pack and its replacement instruction Attention remember that the batteries are consumable parts and they are out of warranty eee u ee ee ee ee ee For conversion table for Fahrenheit and altitude s temperature difference see the inner cover 26 Troubleshooting If the Vera kettle develops faults or defects or if irregularities are suspected unplug it immediately If you cannot e
18. ore cleaning The kettle must be cleaned with a dry or slightly dampened non abrasive cloth soaked with a few drops of neutral non corrosive detergent never use solvents or alkaline cleaning agents Clean the outside surfaces of the kettle ONLY 11 Do not use the kettle under or near flammable material such as curtains wallpaper walls and the like 12 In the event of faults defects or suspected faults after a fall unplug the kettle immediately Never start up a faulty appliance The repairs must be carried out by the CASA BUGATTI Service Centre Contact your dealer and or contact Customer Care at CASA BUGATTI or send an e mail to diva casabugatti it In the event of fire use carbon dioxide CO2 extinguishers Do not use water or powder extinguishers 13 The kettle is only to be used with the stand provided 14 Never fill the kettle with water when it is positioned on the power base unit 15 Never fill the kettle above the MAX mark on the control display panel 2 The kettle has a safety system that will not permit it to switch on if the level is over at 1 75 litres 47 fl oz By the way if the kettle is overfilled of water when boiling water may be ejected 15a CAUTION Do not operate the kettle unless the heating element placed into the kettle is fully immersed 16 Never boil water with the lid open 19 For conversion table for Fahrenheit and altitude s temperature difference see the inner cover IMPORTANT SAFEGUARDS
19. our One click corresponds to one hour and if the setting button A 16 is keep pressed the number rises continuously until the required time is reached c To set the minutes press the mode button 15 one time again and minute numbers start flashing d Press the setting button A to set the minutes One click corresponds to one minute and if the setting button A 16 is kept pressed the number rises continuously until the required time is reached e After setting the minute press mode button 15 for 3 Seconds to finish the setting f To turn the display on clock 10B or temperature 10A press one time the setting button A 16 This operation can be done when the Vera kettle is not heating or boiling Special instruction A Safety cut off Vera is protected against damage resulting from use with an insufficient volume of water In case user press the button on off 14 and on the kettle display the blue light ml minimum blink the kettle will not operate and eventually fill the kettle with water till on the display the blue light of the level ml minimum stop to blink and the blue light of the level 800ml is on Only in this way the kettle can start to operate In case user press the button on off 14 and the kettle is empty or nearly empty and for wrong water level signal the kettle start to heat a safety cut off will automatically disconnect the power supply if the heating element over
20. out too rapidly f To turn the display to the clock 10B or temperature 10A display press the setting button A 16 one time This operation can be done when the Vera kettle is not heating boiling g The water temperature shown on the display correspond to an average temperature of the water inside the kettle Temperature and timer setting functions Vera kettle can heat the water to the temperature required between 45 C and 98 C Tolerance 3 C Vera kettle can switch on at the desired time too J ust follow these simple instructions a Press the mode button 15 for 1 second to enter the temperature setting function and then you will see the blue C icon turn on and the red P icon starts flashing b Press the button A 16 to set the temperature The temperature setting cannot be set higher than 98 C and cannot be set lower than 45 C One click corresponds to 1 C If the A setting button 16 is pressed continuously the temperature number rises until the required temperature has been reached When 98 C is reached and the A setting button 16 is still pressed the temperature numbers start again form 45 C If you need to set only the temperature you can go to the instruction g of this paragraph If you need to set the timer please continue with the instruction c of this paragraph 23 For conversion table for Fahrenheit and altitude s temperature difference see the inner cove
21. r c After setting the temperature press the mode button 15 one time again to set the timer function and then you will see the blue C icon turn off and hour icon will turn and the hours numbers will start flashing d Press the setting button 4 16 to set the hour One click corresponds to one hour and if the setting button A 16 is kept pressed the number rises continuously until the required time is reached e To set the minutes press the mode button 15 one time again and minute numbers being flashing f Press the setting button A to set the minutes One click corresponds to one minute and if the setting button A 16 is kept pressed the number rises continuously until the required time is reached g After setting the temperature or temperature and time you have to press the mode button 15 for 4 seconds to confirm the setting Red P and blue icons turn on and the display will change to show the current time clock h The kettle waits for the heat boil setting time When Vera achieves the set time it starts to heat boil at the set temperature and the red P icon will be off see the point 0 at the end of this paragraph 1 If only the setting of the temperature is required press the on off button 14 the Vera kettle begins to heat boil the water at the set temperature When Vera starts to heat boil at the set temperature the red P ico
22. ring agents of any kind on the interior or exterior of the kettle Do not immerse the kettle or power base in water or other liquid and be sure that the electric kettle plug 6 and connector 5a of the power base 5 is kept dry a Filter 7 Scale or calcium is a natural substance that forms when hard water is boiled The filter serves to retain the calcium in the water kettle It is important to clean the filter regularly The filter clips into the spout and can be removed by pulling it up from the spout It can be cleaned by gently brushing with a soft brush under running water ATTENTION This operation can be perfomed only when the kettle is not working and when the kettle has cooled down DO NOT REMOVE THE FILTER WHEN VERA KETTLE IS WORKING AND WHEN THE SUFACE IS HOT BOILED WATER AND STEAM CAN BURN b Decalcification Decalcification refers to removing the calcium deposits which may form in the interior metal parts of the kettle TO GET THE BEST PERFORMANCE FROM YOUR VERA KETTLE DECALCIFY YOUR UNIT FROM TIME TO TIME Frequency depends on the hardness of your tap water and how often you use the kettle We y suggest to do it every 100 200 boiling cycles or every ee er two weeks or every time you see white spots on the internal bottom surface of the kettle it means that there is limestone sediment We suggest use of a kettle descaler in order to dissolve these chalky deposits or lime build up Follow the instructi
23. s temperature difference see the inner cover 16 TECHNICAL FEATURES Power supply Power rating Dimensions Body Weight Length of power supply cord Thermal overload protection Display Battery kettle capacity Certifications Warranty See rating plate underneath machine See rating plate underneath machine 220 x 180 x h 300 mm 8 1 2 x 7 x 11 3 4 approximately Pressed Solid 18 10 Stainless Steel 1 7 Kg 37 5 Pounds approximately 0 75 meter 30 inches approximately Built in Built in rechargeable 1 75 litres 47 fl oz See rating plate underneath machine As per attached certificate DESCRIPTION OF THE KETTLE PARTS Lid Electronic display Stay cool handle 18 10 stainless steel kettle Power base unit Connector Plug Filter Water maximum level mark CPQO_IOSEHO KETTLE ELECTRONIC CONTROLS Electronic display Segment indication Kettle is heating boling Clock timer Temperature Celsius Degree Program icons Water level display Clock Temperature Timer display on off button mode button A Setting button reset button 0A Temperature display OB Clock Timer display 00 Heating Boiling display ee 17 For conversion table for Fahrenheit and altitude s temperature difference see the inner cover IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS CAREFULLY THE d KETTLE MUST BE USED ONLY BY ADULTS WHO HAVE BEEN TRAINED IN ITS USE SAVE THESE INSTRUCT
24. s to persons e If the power cable or plugs are damaged they must be replaced by the manufacturer or with authorized service centre or by a qualified person in order to prevent all risks 6 Figure B Make sure that children cannot play with the kettle Children are not aware of the dangers of electrical appliances Cleaning and user maintenance should not be made by children without supervision 7 Place the kettle on a flat surface making sure that the feet adhere firmly to the support surface so that the appliance cannot be overturned Do not place the kettle on or near hot surfaces or near naked flames CAUTION Do not operate the kettle on an inclined plane 8 Figure C Pay attention to hot surfaces Use handles or knobs or wear oven gloves Be very careful when touching very hot parts such as lid 1 body 4 and all surfaces of the kettle WARNING DANGER OF BURNS The kettle body 4 and lid 1 become very hot during use 9 Figure D To ensure that the kettle works correctly place it on a flat surface in an adequately lighted and hygienic environment with an easily accessible electrical socket Keep the kettle at least 10 cm 4 inches away from the walls 10 Figure E Never touch the appliance with wet or damp cloths or hands Always unplug the kettle when it is not in use and before cleaning Do not unplug the appliance by pulling on the cord but only holding the plug Allow kettle to cool before fitting or removing parts and bef
Download Pdf Manuals
Related Search