SECO-LARM MVE-AH010Q
Contents
1. prepaid to SECO LARM This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglect repair or alteration improper or abnormal usage or faulty installation or if for any other reason SECO LARM determines that such equipment is not operating properly as a result of causes other than defects in material and workmanship The sole obligation of SECO LARM and the purchaser s exclusive remedy shall be limited to the replacement or repair only at SECO LARM s option In no event shall SECO LARM be liable for any special collateral incidental or consequential personal or property damage of any kind to the purchaser or anyone else NOTICE The information and specifications printed in this manual are current at the time of publication However the SECO LARM policy is one of continual development and improvement For this reason SECO LARM reserves the right to change specifications without notice SECO LARM is also not responsible for misprints or typographical errors Copyright 2013 SECO LARM U S A Inc All rights reserved This material may not be reproduced or copied in whole or in part without the written permission of SECO LARM SECO LARM U S A Inc 16842 Millikan Avenue Irvine CA92606 Website www seco larm com wf PICSNG Tel 949 261 2999 800 662 0800 Email sales seco larm com MiMVE AH010Q_1310 docx 4 SECO LARM U S A Inc2. ENFORCER MVE AH010Q Extender for HDMI Over Dual Cat5e 6 Manual 97 ft Cat5e 6 y HIGH DEFINITION MULTIMEDIA INTERFACE 1080p Resolution Dual Cat5e 6 Operation e Extend HDMI over two Catde 6 cables e Supports resolutions from 480i to 1080p with zero signal loss e Transmits up to 197ft 60m at 1080p over two Cat6 cables e Plug and play operation comes as a complete set amp SZ SECO LARM FE CE Note Products with model numbers that end with Q or that have a round green Q sticker are ROHS compliant ENFORCER Extender for HDMI over Dual Cat5e 6 Introduction The ENFORCER HDMI Extender over Cat5e 6 extends the range of HDMI by using a transmitter and an active receiver to send video and audio over two Catde 6 cables HDMI Formats as high as 1080p can be transmitted up to 197ft 60m between the two units with zero signal loss Features e Signal Strength Transmitter ensures that the signal strength will remain strong over the length of the cable e Distance The HDMI Extender over Catde 6 is capable of providing a clear HDMI signal up to 197ft 60m e Formats Supported The HDMI Extender over Cat5e 6 supports both progressive and interlaced formats 1080p 1080i 720p 5 76p 5761 480p 480i e Plug and Play The HDMI Extender over Cat5e 6 comes as a complete set consisting of a transmitter receiver and power supply No adjustments or settings must be made the unit is ready to use righ
3. t out of the box e Zero Signal Loss Integrated circuits in the transmitter and receiver clean buffer and amplify the HDMI signal to prevent signal loss and ensure a clear signal regardless of the length of the cable Specifications Resolutions supported Cat6 197 60m Cat5e 98 30m 6 75Gbps Parts List 1 x Transmitter MVE AH010Q TQ 1 x 5VDC Power adapter 1 x Receiver MVE AH010Q RQ 1 x Manual 2 SECO LARM U S A Inc ENFORCER Extender for HDMI over Dual Cat5e 6 Overview Back 5VDC Power input SLED Cat5e 6 Ports 2 5VDC i HDMI Output Receiver 9 99E9 ENFORCER 3 O a Status Re Receiver shown Two Cat5e 6 cables are required Please use 1568 B wiring standard Installation 1 Determine the locations where the HDMI to Cat5e 6 units will be placed as well as how much Cat5e 6 cable will be necessary 2 Connect the HDMI to cable to both the transmitter and source device 3 Connect the HDMI cable to both the receiver and display 4 Connect the Cat5e 6 cables to both the receiver and transmitter units Make sure to connect the cables to their respective ports i e Cat5e 6 1 connected to Cat5e 6 1 and Cat5e 6 2 connected to Cat5e 6 2 Note For best results use Cat6 cable Note For best results use solid core cable Stranded core cable is not recommended 5 Connect the 5VDC adapter to the receiver unit 6 Switch on the HDMI source device and display to verify that the system is f
4. unctioning properly Sample Application HDMI Source FE a er e8 Included 5VDC eae Power Adapter m f SECO LARM U S A Inc 3 Use T568B UTP wiring standard Use T568B UTP wiring standard Two Cat5e 6 Cables ENFORCER Extender for HDMI over Dual Cat5e 6 Troubleshooting Reduce the resolution of the source device Turn off deep color Use T568B wiring standard Make sure the Cat5e 6 cables are connected to the correct ports and not to opposite ports Use solid core cable instead of stranded core cable Make sure the HDMI input device is turned on Make sure the HDMI output device is turned on Test the Cat5e 6 cable between the receiver and transmitter to make sure it is operational HDMI Device does not function correctly Also Available from SECO LARM ENHANCED Extenders for HDMI Wireless Extender for HDMI HDMI Matrix HDMI Switch _ _ lt ee ere 5 O 7yo P P HDMI the HDMI Logo and High Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries WARRANTY This SECO LARM product is warranted against defects in material and workmanship while used in normal service for a period of one 1 year from the date of sale to the original consumer customer SECO LARM s obligation is limited to the repair or replacement of any defective part if the unit is returned transportation
Download Pdf Manuals
Related Search