AEG F88709M0P
Contents
1. 8 1 The salt container CAUTION Only use salt specifically designed for dishwashers The salt is used to recharge the resin in the water softener and to assure good washing results in the daily use How to fill the salt container 1 Turn the cap of the salt container counterclockwise and remove it 2 Put 1 litre of water in the salt container Only for the first time 3 Fill the salt container with dishwasher salt a 7 oe 4 Remove the salt around the opening of the salt container oa gt PETE 5 Turn the cap of the salt container clockwise to close the salt container Water and salt can come out from the salt container when you fill it Risk of corrosion To prevent it after you fill the salt container start a programme i 8 2 How to fill the rinse aid dispenser CAUTION Only use rinse aid specifically designed for dishwashers 1 Open the lid C 2 Fill the dispenser B until the rinse aid reaches the marking MAX 3 Remove the spilled rinse aid with an absorbent cloth to prevent too much foam 4 Close the lid Make sure that the lid locks into position i Fill the rinse aid dispenser when the indicator A becomes clear 9 DAILY USE 1 Open the water tap 2 Press the on off button to activate the appliance Make sure that the appliance is in user mode e fthe salt indicator is on fill the salt container e lf the rins2. A 4 Risk of injury or suffocation replace the water inlet hose e Disconnect the appliance from the mains supply 2 4 Use e Cut off the mains cable and discard it e Remove the door catch to prevent children and pets to get closed in the appliance e Do not sit or stand on the open door e Dishwasher detergents are dangerous Obey the safety instructions on the detergent packaging 3 PRODUCT DESCRIPTION Worktop Lower spray arm Upper spray arm Filters 6 www aeg com Rating plate Lower basket EB Salt container Upper basket Air vent Cutlery drawer EJ Rinse aid dispenser E Detergent dispenser 4 CONTROL PANEL Delay 1 Reset Option AUTO Ya Quick Quick Extra ECO SENSE PROZONE PRO Das 6OMIN 30MIN SILENT 50 45 70 50 65 70 55 o 50 leco fauo 034 ro IP Program somn 0Min sient B Start On off button BJ Option touchpad Program touchpad Indicators Programme indicators EJ Start touchpad Display Delay touchpad 4 1 Indicators Indicator Description Washing phase It comes on when the washing phase operates Rinsing phase It comes on when the rinsing phase operates Drying phase It comes on when the drying phase operates End indicator Multitab indicator Salt indicator It is always off while the programme operates Rinse aid indicator It is al
3. and detergent e Only use salt rinse aid and detergent for dishwasher Other products can cause damage to the appliance Multi tablets are usually suitable in areas with a water hardness up to 21 dH In areas exceeding this limit rinse aid and salt must be used in addition to the multi tablets However in areas with hard and very hard water we recommend to use solo detergent powder gel tablets without additional functions rinse aid and salt separately for optimal cleaning and drying results If you use multi tablets you can select the Multitab option if available This option increases the cleaning and drying results with the use of multi tablets Detergent tablets do not fully dissolve with short programmes To prevent detergent residues on the tableware we recommend that you use the tablets with long programmes Do not use more than the correct quantity of detergent Refer to the instructions on the detergent packaging 10 3 What to do if you want to stop using multi tablets Before you start to use separately detergent salt and rinse aid do the following procedure 1 2 Set the highest level of the water softener Make sure that the salt and rinse aid containers are full Start the shortest programme with a rinsing phase Do not add detergent and do not load the baskets When the programme is completed adjust the water softener according to the water hardness in your area Adjust the release
4. multi tablets can be the cause Try a different brand or activate the rinse aid dispenser and use rinse aid and multi tablets together i Refer to Hints and tips for other possible causes ENGLISH 19 13 TECHNICAL INFORMATION Dimensions Width height depth mm 596 850 610 Electrical connection 1 Voltage V 220 240 Frequency Hz 50 Water supply pressure Min max bar MPa 0 5 0 05 8 0 8 Water supply Cold water or hot water Max 60 C Capacity Place settings 18 Power consumption Left on mode W 0 99 Power consumption Off mode W 0 10 1 Refer to the rating plate for other values 2 f the hot water comes from alternative source of energy e g solar panels aeolian energy use the hot water supply to decrease energy consumption 14 ENVIRONMENTAL CONCERNS I Recycle the materials with the symbol Cd Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked with the symbol amp with the household waste Return the product to your local recycling facility or contact your municipal office www aeg com shop fel Mal 117904880 B 152014 A mn HAEG perfekt in form und funktion
5. shock j e Make sure not to cause damage to e The appliance must be earthed the water hoses e Make sure that the electrical e Before you connect the appliance to information on the rating plate agrees new pipes or pipes not used for a with the power supply If not contact long time let the water flow until it is an electrician clean e Always use a correctly installed e The first time you use the appliance shockproof socket make sure that there is no leakage e Do not use multi plug adapters and e The water inlet hose has a safety valve extension cables and a sheath with an inner mains e Make sure not to cause damage to cable the mains plug and to the mains cable Should the mains cable need to be replaced this must be carried out by our Authorised Service Centre Connect the mains plug to the mains socket only at the end of the ENGLISH 5 e Do not drink and play with the water in the appliance e Do not remove the dishes from the appliance until the programme is completed There can be detergent on the dishes e The appliance can release hot steam if you open the door while a programme operates e Do not put flammable products or items that are wet with flammable WARNING products in near or on the appliance Dangerous voltage e If the water inlet hose is damaged 2 5 Disposal immediately disconnect the mains WARNING plug from the mains socket Contact the Authorised Service Centre to I
6. shorter The total programme duration decreases by approximately 50 The washing results are the same as with the normal programme duration The drying results can decrease How to activate TimeSaver Press Option until the indicator A comes on If the option is not applicable to the programme the related indicator does not come on or it flashes quickly for a few seconds and then goes off The display shows the updated programme duration 7 3 ExtraHygiene With this option you have better hygiene results During the last rinsing phase the temperature stays at 70 C for at least 10 minutes How to activate ExtraHygiene Press Option until the indicator gt comes on If the option is not applicable to the programme the related indicator does not come on or it flashes quickly for a few seconds and then goes off The display shows the updated programme duration not adjust the level of the water softener Fill the salt container Fill the rinse aid dispenser Open the water tap Start a programme to remove any processing residuals that can still be BD www aeg com inside the appliance Do not use detergent and do not load the baskets When you start a programme the appliance can take up to 5 minutes to recharge the resin in the water softener It seems that the appliance is not working The washing phase starts only after this procedure is completed The procedure will be repeated periodically
7. the upper basket i At the end of the programme water can still remain on the sides and on the door of the appliance 16 www aeg com 11 CARE AND CLEANING IN WARNING Before maintenance deactivate the appliance and disconnect the mains plug from the main socket i Dirty filters and clogged spay arms decrease the washing results Make a check regularly and if necessary clean them 11 1 Cleaning the filters The filter system is made of 3 parts 1 Turn the filter B counterclockwise and remove it 2 Remove the filter C out of filter B 3 Remove the flat filter A 5 Make sure that there are no residues of food or soil in or around the edge of the sump 6 Put back in place the flat filter A Make sure that it is correctly positioned under the 2 guides ENGLISH 17 11 2 Cleaning the spray arms Do not remove the spray arms Ifthe holes in the spray arms are clogged remove remaining parts of soil with a thin pointed object 11 3 External cleaning e Clean the appliance with a moist soft cloth e Only use neutral detergents e Do not use abrasive products 7 Reassemble the filters B and C abrasive cleaning pads or solvents 8 Put back the filter B in the flat filter A Turn it clockwise until it locks 11 4 Internal cleaning e Carefully clean the appliance including the rubber gasket of the door w
8. EN User Manual FAVORIT 88709MOP Dishwasher FAVORIT 88709WOP HAEG perfekt in form und funktion 2 www aeg com CONTENTS Li SAFETY INFORMATION nee an 3 2 SAFETY INSTRUCHIONS u een 4 SP RODUCTIDE SCRIP TIO IN ee ee een nee 5 4 CONTROLPANE Lisi ea ana lemme nina 6 Se PROGRAMMES s 2 222 2 a ERBE ud 7 Gs SETTINGS nn ae Reel 9 PPO UNO N Sr es Re Ra 11 8 BEFORE FIRST USE ee nina 11 9 DAILY USE nn He ar ee ran 13 TO HINTS AND TIPS2 us 20 0 een neun 14 11s CARE AND CLEANING rauen ee een nee 16 12 TROUBLESHOOTING 0a een une 17 13 TECHNICAL INFORMATIONS san ea ei 19 FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler features you might not find on ordinary appliances Please spend a few minutes reading to get the very best from it Visit our website for Get usage advice brochures trouble shooter service information www aeg com g Register your product for better service www registeraeg com Buy Accessories Consumables and Original spare parts for your appliance www aeg com shop CUSTOMER CARE AND SERVICE Always use original spare parts When contacting our Authorised Service Centre ensure that you have the following data available Model PNC Serial Number The information can be found on the rating pla
9. The appliance is to be connected to the water mains using the new supplied hose sets Old hose sets must not be reused 4 www aeg com 1 2 Children and vulnerable people safety This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Do not let children play with the appliance Keep all detergents away from children Keep children and pets away from the appliance door when it is open Cleaning and user maintenance shall not be made by children without supervision 2 SAFETY INSTRUCTIONS 2 1 Installation installation Make sure that there is access to the mains plug after the e Remove all the packaging installation e Do not install or use a damaged e Do not pull the mains cable to appliance disconnect the appliance Always pull e Do not install or use the appliance the mains plug where the temperature is less than 0 e This appliance complies with the SG E E C Directives e Obey the installation instruction e Only for UK and Ireland The supplied with the appliance appliance has a 13 amp mains plug If A it is necessary to change the fuse in 2 2 Electrical connection the mains plug use a 13 amp ASTA BS 1362 fuse WARNING Risk of fire and electrical 2 3 Water connection
10. ation starts to decrease with steps of 1 minute Starting a programme with delay start 1 Seta programme 2 Press Delay again and again until the display shows the delay time you want to set from 1 to 24 hours 3 Press Start to start the countdown e The delay indicator comes on to confirm the start of the countdown e The countdown starts to decrease with steps of 1 hour Only the last hour will decrease with steps of 1 minute When the countdown is completed the programme starts and the indicator of 14 www aeg com the running phase comes on The delay indicator goes off Opening the door while the appliance operates If you open the door while a programme is running the appliance stops When you close the door the appliance continues from the point of interruption Cancelling the delay start while the countdown operates When you cancel the delay start you have to set the programme and options again Press simultaneously Delay and Option until the appliance is in programme selection mode Cancelling the programme 1 Open the appliance door 2 Press the on off button to deactivate the appliance 3 Keep the appliance deactivated for approximately 10 seconds 4 Press again the on off button to activate the appliance 5 Press and hold simultaneously Delay and Option until the appliance is in programme selection mode 10 HINTS AND TIPS 10 1 General The following hints will ensure o
11. d quantity of rinse aid 10 4 Loading the baskets Only use the appliance to wash items that are dishwasher safe Do not put in the appliance items made of wood horn aluminium pewter and copper ENGLISH 15 e Do not put in the appliance items that can absorb water sponges household cloths e Remove remaining food from the items e Make soft the remaining burned food on the items e Put hollow items cups glasses and pans with the opening down e Make sure that cutlery and dishes do not bond together Mix spoons with other cutlery e Make sure that glasses do not touch other glasses e Put small items in the cutlery basket e Put light items in the upper basket Make sure that the items do not move e Make sure that the spray arm can move freely before you start a programme 10 5 Before starting a programme Make sure that e The filters are clean and correctly installed e The cap of the salt container is tight e The spray arms are not clogged e There is dishwasher salt and rinse aid unless you use multi tablets e The position of the items in the baskets is correct e The programme is applicable for the type of load and for the degree of soil e The correct quantity of detergent is used 10 6 Unloading the baskets 1 Let the tableware cool down before you remove it from the appliance Hot items can be easily damaged 2 First remove items from the lower basket then from
12. e aid indicator is on fill the rinse aid dispenser 3 Load the baskets 4 Add the detergent If you use multi tablets activate the option Multitab 5 Set and start the correct programme for the type of load and the degree of soil 9 1 Using the detergent A B AN CAUTION Only use detergent specifically designed for dishwashers 1 Press the release button A to open the lid C 2 Putthe detergent in powder or tablets in the compartment B 3 If the programme has a prewash phase put a small quantity of detergent on the inner part of the appliance door 4 Close the lid Make sure that the lid locks into position ENGLISH 13 9 2 Setting and starting a programme The Auto Off function This function decreases energy consumption by deactivating automatically the appliance when it is not operating The function comes into operation e 5 minutes after the completion of the programme e After 5 minutes if the programme has not started Starting a programme 1 Close the appliance door 2 Press the on off button to activate the appliance Make sure that the appliance is in programme selection mode 3 Press Program again and again until the indicator of the programme you want to select comes on The display shows the programme duration 4 Set the applicable options 5 Press Start to start the programme e The indicator of the running phase comes on e The programme dur
13. e pressure of the water supply is not too low For this information contact your local water authority Make sure that the water tap is not clogged Make sure that the filter in the inlet hose is not clogged Make sure that the inlet hose has no kinks or bends Make sure that the sink spigot is not clogged Make sure that the drain hose has no kinks or bends The anti flood device is on The display shows fell Close the water tap and contact an Authorised Service Centre Once you have checked the appliance deactivate and activate the appliance If the problem occurs again contact an Authorised Service Centre For alarm codes not described in the table contact an Authorised Service Centre 12 1 The washing and drying results are not satisfactory Problem Possible solution There are whitish streaks or bluish layers on glasses and dishes The release quantity of rinse aid is too much Adjust the rinse aid selector to a lower position The quantity of detergent is too much There are stains and dry water drops on glasses and dishes The dishes are wet The released quantity of rinse aid is not sufficient Ad just the rinse aid selector to a higher position The quality of the rinse aid can be the cause The programme does not have a drying phase or has a drying phase with low temperature The rinse aid dispenser is empty The quality of the rinse aid can be the cause The quality of the
14. ith a soft moist cloth e Ifyou regularly use short duration programmes these can leave deposits of grease and limescale inside the appliance To prevent this we recommend to run long duration programmes at least 2 times per month IN CAUTION An incorrect position ofthe filters can cause bad washing results and damage to the appliance 12 TROUBLESHOOTING If the appliance does not start or it stops With some problems the display during operation Before you contact an shows an alarm code Authorised Service Centre check if you can solve the problem by yourself with the help of the information in the table Problem and alarm code Possible solution You cannot activate the ap Make sure that the mains plug is connected to the pliance mains socket e Make sure that there is no a damage fuse in the fuse box 18 www aeg com Problem and alarm code Possible solution The programme does not start Make sure that the appliance door is closed Press Start If the delay start is set cancel the setting or wait for the e nd of the countdown The appliance has started the procedure to recharge the resin inside the water softener The duration of the procedure is approximately 5 minutes The appliance does not fill with water The display shows id The appliance does not drain the water The display shows cll Make sure that the water tap is open Make sure that th
15. ority can advise you on the hardness of the water in your area It is important to set the right level of the water softener to assure good washing results German de French degrees mmol l Clarke de Water softener lev grees dH fH grees el 47 50 84 90 8 4 9 0 58 63 10 43 46 76 83 7 6 8 3 53 57 9 37 42 65 75 6 5 7 5 46 52 8 29 36 51 64 5 1 6 4 36 45 7 23 28 40 50 4 0 5 0 28 35 6 19 22 33 39 3 3 3 9 23 27 5 15 18 26 32 2 6 3 2 18 22 4 11 14 19 25 1 9 2 5 13 17 3 4 10 7 18 0 7 1 8 5 12 2 lt 4 lt 7 lt 0 7 lt 5 12 1 Factory setting 2 Do not use salt at this level www aeg com How to set the water softener level The appliance must be in programme selection mode 1 To enter the user mode press and hold simultaneously Delay and Option until the indicators ECO AUTO and Uy start to flash and the display is blank 2 Press Program e The indicators AUTO and Ya go off e The indicator ECO continues to flash e The display shows the current setting e g 5 L level 5 3 Press Program again and again to change the setting 4 Press the on off button to confirm the setting 6 3 The rinse aid dispenser The rinse aid helps to dry the dishes without streaks and stains The rinse aid is automatically released during the hot rinse phase You can set the released quantity of rinse aid between level 1 minimum quantity and level 6 maxim
16. ptimal cleaning and drying results in daily use and also help to protect the environment e Remove larger residues of food from the dishes into the waste bin e Do not pre rinse dishes by hand When needed use the prewash programme if available or select a programme with a prewash phase e Always use the whole space of the baskets e When loading the appliance make sure that the dishes can be completely reached and washed by the water released from the spray arm Make sure that there is detergent in the detergent dispenser before you start a new programme End of the programme When the programme is completed the display shows 0 00 and the end indicator is on All buttons are inactive except for the on off button 1 Press the on off button or wait for the Auto Off function to automatically deactivate the appliance If you open the door before the activation of Auto Off the appliance is automatically deactivated 2 Close the water tap nozzles Make sure that items do not touch or cover each other e You can use dishwasher detergent rinse aid and salt separately or you can use the multi tablets e g 3in1 4in1 Allin 1 Follow the instructions written on the packaging e Select the programme according to the type of load and degree of soil With the ECO programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil 10 2 Using salt rinse aid
17. r test gP performance send an email to 6 SETTINGS 6 1 Programme selection mode and user mode When the appliance is in programme selection mode it is possible to set a programme and to enter the user mode In user mode the following settings can be changed e The level of the water softener according to the water hardness e The deactivation of the rinse aid dispenser when you want to use the Multitab option without rinse aid e The level of rinse aid according to the required dosage These settings will be saved until you change them again How to set the programme selection mode The appliance is in programme selection mode when the programme indicator ECO is on and the display shows the programme duration Water hardness ENGLISH 9 When you activate the appliance usually it is in programme selection mode However if this does not happen you can set the programme selection mode in the following way Press and hold simultaneously Delay and Option until the appliance is in programme selection mode 6 2 The water softener The water softener removes minerals from the water supply which would have a detrimental effect on the washing results and on the appliance The higher the content of these minerals the harder your water is Water hardness is measured in equivalent scales The water softener should be adjusted according to the hardness of the water in your area Your local water auth
18. soil and the quantity of items in the baskets It automatically ad justs the temperature and the quantity of water the energy consumption and the programme duration 3 With this programme you can wash a load with mixed soil Very heavy soil in the lower basket and normal soil in the upper basket The pressure and the temperature of the water in the lower basket are higher than in the upper basket 4 This programme has a high temperature rinsing phase for better hygiene results During the rinsing phase the temperature stays at 70 C for at least 10 minutes 5 With this programme you can wash a load with fresh soil It gives good washing results in a short time This is the most silent programme The pump works at a very low speed to decrease the level of noise Because of the low speed the programme duration is long 5 1 Consumption values Water Energy Duration 1 kWh min ECO 11 0 961 225 AUTO 7 14 0 6 1 4 40 150 Programme 1 Ya 14 16 12 gt 1 3 139 149 PRO 12 5 14 5 1 4 1 6 154 164 y 12 14 0 7 0 9 75 85 60MIN 9 5 10 5 1 10 1 30 55 65 MN o ovv o 1 The pressure and the temperature of the water the variations of the mains supply the options and the quantity of dishes can change the values 5 2 Information for test info test dishwasher production com institutes Write down the product number PNC f that is on the rating plate For all the necessary information fo
19. t setting i d rinse aid dispenser activated 3 Press Start to change the setting O d rinse aid dispenser deactivated The rinse aid indicator goes off 4 Press the on off button to confirm the setting 7 OPTIONS Desired options must be activated every time before you start a programme It is not possible to activate or deactivate options while a programme is running i Not all options are compatible with each other If you have selected non compatible options the appliance will automatically deactivate one or more of them Only the indicators of the options still active will stay on i 7 1 Multitab Activate this option when you use multi tablets that integrate the salt rinse aid and detergent functions They can also contain other cleaning or rinsing agents This option deactivates the release of salt The salt indicator does not come on With the use of this option the programme duration is prolonged to increase the cleaning and drying results with the use of multi tablets Multitab is not a permanent option and must be selected at every cycle How to activate Multitab Press Option until the indicator comes on 7 2 TimeSaver This option increases the pressure and the temperature of the water The 8 BEFORE FIRST USE 1 Make sure that the current level of the water softener agrees with the hardness of the water supply If ENGLISH 11 washing and the drying phases are
20. te A Warning Caution Safety information i General information and tips Environmental information Subject to change without notice ENGLISH 3 1 A SAFETY INFORMATION Before the installation and use of the appliance carefully read the supplied instructions The manufacturer is not responsible if an incorrect installation and use causes injuries and damages Always keep the instructions with the appliance for future reference 1 1 General Safety This appliance is intended to be used in household and similar applications such as farm houses staff kitchen areas in shops offices and other working environments by clients in hotels motels bed amp breakfast and other residential type environments Do not change the specification of this appliance The operating water pressure minimum and maximum must be between 0 5 0 05 8 0 8 bar Mpa Obey the maximum number of 15 place settings If the supply cord is damaged it must be replaced by the manufacturer its Authorised Service Centre or similarly qualified persons in order to avoid a hazard Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position Do not keep the appliance door open without supervision to prevent to fall on it Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket Do not use water spray and steam to clean the appliance
21. um quantity Level O will deactivate the rinse aid dispenser and no rinse aid will be released Factory setting level 4 How to set the rinse aid level The appliance must be in programme selection mode 1 To enter the user mode press and hold simultaneously Delay and Option until the indicators ECO AUTO and Yr start to flash and the display is blank 2 Press Delay e The indicators ECO and AUTO go off e The indicator amp continues to flash e The display shows the current setting e g YR level 4 The levels of rinse aid are from OA to 6A Level 0 no rinse aid is released 3 Press Delay again and again to change the setting 4 Press the on off button to confirm the setting 6 4 Use of rinse aid and multi tablets When you activate the option Multitab the rinse aid dispenser continues to release rinse aid However you can deactivate the rinse aid dispenser In this case the drying results may not be satisfactory With the rinse aid dispenser deactivated the rinse aid indicator is always off How to deactivate the rinse aid dispenser The appliance must be in programme selection mode 1 To enter the user mode press and hold simultaneously Delay and Option until the indicators ECO AU TO and Y start to flash and the display is blank 2 Press Start e The indicators ECO and amp go off The indicator AU TO continues to flash e The display shows the curren
22. ways off while the programme operates Indicator Description ENGLISH 7 TimeSaver indicator Delay indicator ExtraHygiene indicator 5 PROGRAMMES Programme Degree of soil Programme phases Options Type of load ECO 1 e Normal soil e Prewash e ExtraHygiene e Crockery and cut e Wash 50 C e TimeSaver lery e Rinses e Multitab e Dry AU TO 2 e All e Prewash e ExtraHygiene e Crockery cutlery Wash from45 C e Multitab pots and pans io on e Rinses e Dry U 3 e Mixed soil e Prewash e TimeSaver e Crockery cutlery Wash 50 C and e Multitab pots and pans OAC e Rinses e Dry PRO e Heavy soil e Prewash e TimeSaver e Crockery cutlery Wash 70 C e Multitab pots and pans e Rinses e Dry y e Normal or light e Wash 45 C e Multitab soil e Rinses e Delicate crockery Dry and glassware 60MIN e Light soil e Wash 55 C e ExtraHygiene e Crockery and cut e Rinses e Multitab lery 30MIN gt e Fresh soil e Wash 60 C e ExtraHygiene e Crockery and cut Rinses e Multitab lery www aeg com Programme Degree of soil Programme phases Options Type of load SILENT e Normal soil e Prewash e Multitab e Crockery and cut e Wash 50 C lery e Rinses e Dry 1 With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil This is the standard programme for test institutes 2 The appliance senses the degree of
Download Pdf Manuals
Related Search