Miele TMB 640 WP tumble dryer
Contents
1. Check the seams of padded or down filled items to prevent the risk of fillings coming out These could catch fire when being dried Disentangle the laundry Tie together textile belts and ties Fasten duvet covers and pillow cases to prevent small items from being trapped inside them hooks and eyes Sew in or remove underwiring from bras Leave jackets open and undo any long zips so that textiles dry evenly Minimum iron fabrics tend to crease more the greater the load This is also the case for garments made from very fine weave fabric such as shirts or blouses If necessary reduce the size of the load for these types of fabric 21 1 Notes on correct laundry care Garment care label symbols Drying Normal higher temperature Reduced temperature Select Gentle tumble for delicate textiles Ed Do not tumble dry Ironing ZA Very hot Z Hot A Warm zxX Do not iron Laundry care when drying in a tumble dryer See the Programme chart This describes the programmes and gives their maximum load Load according to the optimum amount of laundry recommended for the programme being used Underloading is uneconomical Overloading gives a poorer quality of drying and may cause unnecessary creasing Select an appropriate drying level eg Normal if you want to fold and put away the laundry after yo2. 49 Problem solving guide Bottom right grille A In general the cooling fins behind the grille on the bottom right do not need cleaning They should only be cleaned if the drying process is taking an exceptionally long time due to a very high level of dust or fluff in the room in which the dryer is located m First open the plinth filter panel bottom left m Then insert a spoon handle behind the grille on the right hand side m Lever off the grille at the top 1 m Lever off the grille at the bottom 2 m Open the grille out to the right 3 m and pull it forwards releasing its 3 hooks to remove it from the dryer 50 N Danger of injury Do not touch the cooling fins You could cut yourself A Use a vacuum cleaner with a dusting brush attached to clean the cooling fins Only pass the vacuum cleaner brush over them lightly without applying any pressure Take care not to bend the cooling fins out of shape or to damage them m Carefully vacuum up any visible fluff or soiling m Re insert the 3 hooks on the grille into the appropriate holes in the front of the dryer m Press the grille firmly back into position by pressing it in at the top and bottom on the left After sales service Repairs In the event of any faults which you cannot remedy yourself please contact your Miele Dealer or the Miele Service Department Contact details for Miele are given at the end
3. with damaged fluff filters or with a damaged plinth filter This would cause an excessive build up of fluff which in turn would cause a fault gt The fluff filters must be cleaned after every drying cycle gt The fluff filters and the plinth filter must be thoroughly dried after cleaning Do not replace them if they are damp or wet Damp or wet filters could cause operational faults gt Do not install the tumble dryer in a room where there is a risk of frost occurring At temperatures around freezing point the tumble dryer may not be able to operate properly There is a risk of damage if the condensed water is allowed to freeze in the pump and hoses gt If the water is drained externally through the drain hose instead of being collected in the condensed water container make sure the drain hose is securely attached if you hang it in a sink or basin to avoid the hose slipping and the water causing damage 14 Warning and Safety instructions Condensed water is not drinking water It can cause health problems in both people and animals if consumed Always keep the area around the tumble dryer free of dust and fluff Dust drawn into the tumble dryer can cause blockages in the heat exchanger over time gt The tumble dryer must not be hosed down Warning and Safety instructions Using a fragrance flacon optional accessory gt Only use genuine Miele original fragrance flacons gt The fragranc
4. 25 syztadiar geireror ine 26 4 Remove the laundry eene neret nnns enne 27 End of DrogrammeiAnt Crease EEN 27 Remove the 3 P Into a Cm 27 EIERE ite eege 28 Gentlet mble urn en eu 28 le 28 EEN 28 Delay starE E 29 Programme chart d rre I EX ded ana et 30 Changing the programme sequence eee eeenae eee teeeaaeeeeteteaaeeeeneee 33 Cleaning and care sieran taan e ER LEREREHEEESEPENSPEEEEPERFEERUERENNEERSERFERSESPELER 34 Emptying the condensed water container uussssssnsnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnnn ann 34 dilute TEUER 35 Removing visible TlUff nn en a an 35 Cleaning the fluff filters and air flow openings thoroughly 36 SU ie BULLE 37 Removing the plinth filter ee 37 Cleaning the plinth filter sessionis aaia 37 Contents Cleaning the plinth filter Dame 38 Checking the condenser UNit 22 cceccceecceeeseeeeeeeeeseceeeeeesseeeeeeesseeeeeeeneeeeneeees 38 Replacing the plinthifilter iine ae 39 Fragrance E ET 41 Inserting a fragrance flacon ssssssssssee enne 41 Replacing the fragrance flacon eese nennen 43 Problem solving guide nnne nnne nnns 45 Check indicators and fault messages 45 Unsatisfactory drying results uuesserssnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 47 Eegeregie 48 Bottom right grille e ee 50 After sales service come pe EN ER RRTAEEENRENM EEENYRHRSRRERE NO
5. B2 etc Q Touch the sensor to switch to the next option Programmable function Available options 00 0I 02 03 04 05 06 07 PoI X X X O X X XxX Pod XI X IX OX X X PUH O X X X x to 09 POS olx Po5 O X PH OI x Pog olx Po9 O X FIIX OI x D X O X D ois Du X0 X Can be selected O Factory default setting Q Confirm your selection of the option selected by pressing the Start Stop button The number of the programmable function e g POI will light up again IV To exit programming Switch the dryer off The option you have selected is now stored in memory You can change it again at any time The following example illustrates the programming procedure 71 Programmable functions Example The example describes how to call up the POS Keypad tone programmable function When the Keypad tone programmable function is switched on a tone will sound every time a button is pressed when operating the dryer I To access programming Before you begin ensure that The tumble dryer is switched off The door is closed Q Press the Start Stop button and keep it pressed in whilst carrying out steps O O Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button PG will light up Il Selecting the progr
6. circulating drying air takes place 10 The humming noises caused by the heat pump are normal and do not impair the efficient functioning of the dryer The refrigerant is not flammable or explosive In general it is not necessary to leave the dryer standing for any length of time before it is connected to the mains provided it has been transported and installed correctly see Installation and connection If it has not been transported as described ensure that the recommended standing time prior to first operation is observed Otherwise the heat pump can be damaged This tumble dryer contains fluorinated greenhouse gases They are hermetically sealed Designation R 134a Warning and Safety instructions Please observe the instructions in Installation and connection and the Technical data gt The accessibility of the plug must always be ensured in order to disconnect the tumble dryer from the mains gt Do not block the gap between the bottom of the tumble dryer and the floor with plinth facings deep pile carpet etc This would hinder a sufficient flow of air to the dryer Make sure the dryer door can be opened without hindrance after installation Correct use The maximum load for this tumble dryer is 8 0 kg dry weight The maximum recommended loads for individual programmes are given in the Programme chart gt To prevent the risk of fire do not connect the tumble dryer via a controllable so
7. held liable for the consequences of an inadequate earthing system e g electric shock gt Do not connect the appliance to the mains electricity supply by an extension lead multi socket adapter or similar These can overheat and are a fire hazard gt If the electrical connection cable is faulty it must only be replaced by a Miele authorised service technician to protect the user from danger gt Unauthorised repairs could result in unforeseen dangers for the user for which Miele cannot accept liability Repairs should only be undertaken by a Miele approved service technician otherwise any subsequent damage will not be covered by the guarantee gt Faulty components must only be replaced by genuine Miele original spare parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used gt The tumble dryer must be isolated from the electricity supply in the event of a fault and during cleaning and maintenance 8 Warning and Safety instructions gt This tumble dryer must not be used in a non stationary location e g on a ship gt Do not make any alterations to the tumble dryer unless authorised to do so by Miele Warning and Safety instructions gt Heat pump technology and refrigerant The heat pump in this tumble dryer uses a refrigerant which is condensed by the compressor and led in a closed circuit through the heat exchanger unit where heat exchange with the
8. side m Push the orange marker round to the other side so that you will see at which side to pull the door open Important Please keep the lock catch and door hinge covers which were no longer needed in a safe place These will be required if for example you move house and need to change the door hinging back to its original position 65 Installation and connection Electrical connection U K All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations BS 7671 in the UK Ensure power is not supplied to the appliance until after installation work has been carried out The appliance is supplied with a mains cable with moulded plug ready for connection to a 230 240V mains supply Please ensure the connection data quoted on the data plate match the household mains supply Connection should be made via a suitable switched socket which is easily accessible after installation For extra safety it is advisable to protect the appliance with a suitable residual current device RCD Contact a qualified electrician for advice Do not connect via an extension lead Extension leads do not guarantee the required safety of the appliance e g danger of overheating 66 Non rewireable plugs BS 1363 The fuse cover must be refitted when changing the fuse and if the fuse cover is lost the plug must not be used unt
9. the zips next time m If the problem recurs dry these items using the Warm air timed drying programme Before starting another programme m Switch the dryer off and then on again There are humming noises The compressor is operating These noises are quite normal and do not indicate a fault 48 Problem solving guide Problem Cause and remedy A programme does not start No obvious cause m Connect the tumble dryer to the mains m Turn on the tumble dryer m Close the door m Check whether the mains fuse has tripped Has there been a power cut When power is restored any previously running programme will restart automatically The display is dark and the Start Stop button is flashing slowly The dryer is in standby mode This is quite normal and does not indicate a fault m See Programmable functions DU Standby The drum will turn at intervals in the anti crease phase The dryer is switched off at the end of the programme The dryer switched off automatically This is quite normal and does not indicate a fault m See Programmable functions Pi Automatic switch off The interior drum lighting does not come on The drum lighting will switch off automatically when the door is closed after a few minutes when the door is open to save energy If the dryer is switched on the drum lighting will come on when the door is opened
10. until a 2_ flashes in the first position m Confirm this by pressing the Start Stop button m Enter the two other numbers in the same way The dryer is ready for use after 250 has been entered and confirmed 74 POB Conductivity A This programmable function should only be set if the residual moisture reading in your laundry is incorrect due to extremely soft water Conditions This programmable function should only be set if the water used for washing the laundry is extremely soft with a conductivity reading electrical conductivity less than 150 uS Contact your local water authority for the conductivity level of your mains water supply A Only activate this programmable function for the conditions described above Otherwise drying results can be unsatisfactory Options Ol Factory default off G2 Low conductivity Programmable functions DU Additional drying levels You can activate additional drying levels for many of the programmes Normal drier than the Normal drying level Slightly dry damper than Normal drying level Hand iron 55 damper than the Hand iron drying level This programmable function is only available for programmes with a selectable drying level Options 00 Factory default Bil Drying level stages added Once this programmable function has been activated you will have the option of selecting the additional drying levels when you select a progra
11. will remain lit up while the dryer is switched on 76 Programmable functions Pl Automatic switch off DI Memory To save energy the dryer will switch off automatically after 15 minutes You can lengthen or shorten the time However there is no automatic switch off in the event of a fault The dryer will switch off automatically after 15 minutes if no further selection is made after switching the dryer on atthe end of the anti crease phase after a programme without an anti crease phase has finished Options O1 Switch off after 10 minutes G2 Factory default Switch off after 15 minutes 03 Switch off after 20 minutes The electronics will store in memory a drying level or options for a selected programme The duration selected for a timed drying programme will also be stored in memory These settings will then appear the next time the programme is chosen Options 00 Factory default Memory off G Memory on Exception The Cottons lt __ programme will remain unchanged PIY Anti crease If you have pressed the Anti crease button the drum will continue to rotate in a special anti crease rhythm for a maximum of 2 hours after the end of the drying process This helps prevent creasing if laundry is not going to be removed immediately You can reduce the duration of the anti crease phase Options G 1 hour anti crease G2 Factory defaul
12. will switch off automatically 15 minutes after the end of the programme anti crease phase or after being switched on if no other selection is made Operating the tumble dryer Display 9 Extra dry Normal Hand iron Machine iron SEH 2 7 Time display The programme duration remaining will be displayed in hours minutes The duration displayed for the Cottons Minimum iron Delicates Outerwear Proofing Denim Gentle smoothing programmes may vary or jump The following factors among others affect the programme duration displayed the quantity of laundry the type of fabric and the residual moisture in the laundry The electronics continually assess conditions in the appliance and then adjust the programme duration with increasing accuracy Check fault indicators These are only visible when necessary empty the condensed water container or check the drain hose clean the plinth filter airways technical fault call the Service Department 9 Drying level display For selecting the drying level for programmes with a selectable drying level See 62 V sensor lt gt sensor This sensor has two functions Touching the symbol will Select a later start time for the programme delay start will flash during selection amp will light up constantly when the delay start time is counting down Select the duration of the Warm air programme will flash
13. you are aware of the effect selecting the different options will have on your dryer Programming is carried out in 8 steps using buttons and sensors I To access a programmable function Before you begin ensure that The tumble dryer is switched off The door is closed Q Press the Start Stop button and keep it pressed in whilst carrying out steps O O Switch the dryer on Wait until the Start Stop button lights up constantly and then release the Start Stop button 70 Il To select a programmable function The number of the programmable function will appear in the display as P and a number e g POI Touch the lt gt sensor to select the other programmable functions one by one Programmable function PGi Cottons programme drier or damper DU Minimum iron programme drier or damper POY Extended cool down POS Buzzer volume POG Keypad tone POT Code PUB Conductivity POS Additional drying levels Pl Standby Pl Automatic switch off PIJ Memory PI Anti crease Q Confirm your selection of the programmable function by pressing the Start Stop button Programmable functions Ill To select a different option The options allow you to alter the features of the particular programmable function The option will appear in the time display as and a number e g HD or 0I or
14. 1 before testing dry a 3 kg load of cotton laundry with 70 residual moisture as per the above standard using the Cottons Normal programme without any options selected Consumption data can vary from the nominal values given above depending on the size of the load type of fabric residual moisture level after spinning fluctuations in the electricity supply and any options selected 67 Technical data Height Width Depth Depth with door open Suitable for pushing under a worktop Suitable for stacking Weight Drum volume Load size Capacity of condensed water container Hose length Maximum delivery head Maximum drain hose length Length of connection cable Voltage Connected load Fuse rating Test certificates awarded Energy consumption LEDs 68 850 mm 596 mm 643 mm 1077 mm Yes Yes approx 61 5 kg 120 litres 8 0 kg weight of dry laundry 4 8 1 60 m 1 50 m 4 00 m 2 00 m See data plate See data plate See data plate See data plate See Consumption data Class 1 Programmable functions Various settings can be reprogrammed to alter the dryer s electronics to suit different requirements They can be altered at any time 69 Programmable functions Programming You can use the programmable functions to alter the dryer s electronics to suit your requirements Please read the following pages which describe the various programmable functions so that
15. Note Wool and wool blend items are only fluffed up they are not dried completely Remove garments as soon as the programme has finished Warm air Max load 8 0 kg Use for Multi layered fabric whose layers have different drying characteristics e g jackets pillows sleeping bags and other voluminous items Drying individual items e g bath towels swimwear and tea towels Note Do not select the longest drying time to start with Check the items as you are drying them to find the optimum time Tip You can use the Warm air programme to help remove odours from clean cotton clothing select a duration between 1 2 and 1 hour To improve the freshening up effect dampen the garments a little beforehand and use a fragrance flacon optional accessory Odours will not be removed as effectively from any parts of the garments which are made of synthetic fibre Delicates Max load 2 5 kg Normal Hand iron Use for Delicate items with the KJ symbol on the care label made of synthetic fibre mixed fibre rayon and easy care cotton e g shirts blouses lingerie and appliqued garments Note Reducing the load will reduce creasing Weight of dry laundry 31 Programme chart Gentle smoothing Max load 1 0 kg Normal Hand iron Use for Cotton and linen fabric Minimum iron items made of cotton synthetic or mixed fibre e g trouse
16. UO EENEKR ET 51 Ee TEE 51 Optioridl decessorles rerni fece erdt enr E m irt res LEE 51 Guar ntee UlR ea a re u nalen 51 Guarantee Other coumtrles nennen 51 Installation and conpnechon enne 52 Brent EE 52 Rear VIEW nn svoeee 53 Transporting the ele 53 Installation sec 54 Levelling th dryer ae nn 54 Maker 54 Before moving the tumble dryer again e g when moving house 54 Additional installation requireMent nenne 55 External condensed water outlet EE 56 Installation conditions requiring a non return ve 56 Arranging Bull 57 EX MPIOS EET 58 Changing the door hinglng 5 une ea 60 Changing the hinging over 60 liac 65 Electrical connection DH CEP 66 Consumption data eor EX EE aaaea nase SERRE ERRARE 67 Technical E EE 68 Programmable functions sessi nnne nentes 70 Programming e 70 4 Contents Be 72 PG Cottons programme drier or damper sess 73 PU Minimum iron programme drier or damper sees 73 PES Extended Cool down nennen eege DR 73 POS Buzzer volume seen nennen nennen nnns ener nanan Enn rens sene nnns 73 PUG Keypad torne een ee en oe 73 uon I ME 74 PUG Gonductivily 222 el Ee Se Ri 74 PGS Additional drying eye 75 Pli Stand DY PED 76 Pl Automatic SWitCh Off esses seen nnne nenne nnns nnns 77 PII MEMON ATHE 77 PLY Ant C
17. _ Miele Operating instructions Heat pump dryer To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time en GB M Nr 10 000 810 Caring for the environment Disposal of the packing material The packaging is designed to protect the appliance from damage during transportation The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites Disposal of your old appliance Electrical and electronic appliances often contain valuable materials They also contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre Ensure that it presents no danger to children while being stored for disposal Energy saving tips To avoid unnecessarily long drying times and high consumption of energy Make sure that your laundry is thoroughly spun before drying The higher the spin the greater the savings that can be made in energy an
18. a fault The appliance lid cannot be removed The electrical socket must be located in an accessible position near the appliance Drying durations may increase slightly Optional accessories Washer dryer stack The tumble dryer can be combined with a Miele washing machine in a washer dryer stack The appropriate Miele washer dryer stacking kit is required Plinth The tumble dryer can be fitted on a plinth with drawer please note the plinth may not be available in all countries 55 Installation and connection External condensed water outlet Notes When drying is in progress condensed water is pumped into the condensed water container through the drain hose which is located at the back of the dryer The condensed water can also be drained away via the drain hose so that the condensed water container does not have to be emptied Drain hose length 1 60 m Maximum delivery head 1 50 m Maximum drain hose length 4 00 m The following optional accessories are available an extension hose anon return valve kit for connection to an external water outlet The kit includes an extension hose 56 Installation conditions requiring a non return valve A There is a risk of back flow into the dryer if a non return valve is not fitted Back flow could damage the dryer and also the room in which it is located Certain installation conditions such as tho
19. ammable function Touch the sensor repeatedly until 06 lights up Confirm selection of POS by pressing the Start Stop button 72 III To select a different option OD will light up in the time display These numbers mean that the keypad tone is switched off To switch on the keypad tone Touch the lt sensor so that O lights up Q Confirm selection of by pressing the Start Stop button POG will light up again IV To exit programming Switch the dryer off To check the programming m Switch the dryer on m Press any button A tone will sound each time you press a button m Switch the dryer off Reverting to the previous programming m You can switch off the keypad tone at any time by repeating the steps described in this example Select the 28 option in step Programmable functions DUT Cottons programme drier or damper or P82 Minimum iron programme drier or damper effectively as possible However if you require the laundry to be drier or damper you can alter all the drying levels for one of these programmes at the same time The electronics are designed to dry as Options Gi very damp G2 even damper 03 damper 04 factory default 05 drier 06 even drier 01 very dry Exception The Cottons lt __ programme will remain unchanged DUU Extended cool down The automatic cooling down phase which takes place before the end of a pro
20. any unevenness in the floor 54 Ventilation A The cool air intake at the front of the dryer must not be blocked or covered This would hinder a sufficient intake of cool air for the heat exchanger A Do not block the gap between the bottom of the tumble dryer and the floor with plinth facings deep pile carpet etc This would hinder a sufficient flow of air to the dryer Air which is taken in to cool the heat exchanger is then blown back out of the dryer and warms up the air in the room It is therefore very important to ensure adequate ventilation e g by opening a window Otherwise drying durations may be longer increased energy requirement Before moving the tumble dryer again e g when moving house After each use a small quantity of condensed water will collect in the area of the pump This water can run out if the tumble dryer is tipped up when it is being moved Recommendation run the Warm air programme for approximately 1 minute before moving the tumble dryer Any remaining condensed water will then be fed into the condensed water container or out through the drain hose Installation and connection Additional installation requirements Pushing the dryer under a worktop This tumble dryer is suitable for pushing under a worktop A It is very important to avoid a build up of heat The warm air which is expelled from the dryer must be able to dissipate Warm air which cannot dissipate could cause
21. as those described under Cottons Normal with normal residual moisture Note Items are dried to a Normal level only The Cottons X programme is the most energy efficient for drying cotton items with normal residual moisture levels Cottons Max load 8 0 kg Extra dry Normal Use for Single and multi layered cotton fabric such as towelling jerseywear T shirts underwear workwear covers flannelette bed linen and baby clothes Note Select Extra dry for multi layered and very thick fabric Do not use Extra dry for jersey fabric e g T shirts underwear as they have a tendency to shrink Hand iron Machine iron Use for Cotton or linen fabric requiring further processing e g table linen bed linen starched laundry Note To prevent laundry from drying out it should be rolled up until you are ready for ironing Minimum iron Max load 4 0 kg Normal Hand iron Use for Minimum iron items made of cotton synthetic or mixed fibre e g workwear tunics tops dresses trousers table linen and socks Weight of dry laundry Note for test institutes Test programme in accordance with Regulation 392 2012 EU for energy labelling measured in accordance with EN 61121 without any options selected 30 Programme chart Woollens handcare Max load 2 0 kg Use for Woollen garments and fabric containing wool blends e g pullovers jackets and socks
22. ce leaking do not store the packaging upright on its edge or upside down store in a cool dry place store away from direct sunlight 44 when purchasing new fragrance flacons only remove the protective seal just before use Cleaning the fluff filters The intensity of the fragrance will be diminished if the fluff filters and the plinth filter are not cleaned A The fragrance filter must be removed before cleaning the fluff filter A To prevent any fragrance leaking out of the flacon when not in use the fragrance flacon must only be stored in its original packaging as illustrated m Clean the fluff filters and the plinth filter see Cleaning and care Problem solving guide With the help of the following notes minor faults in the performance of the appliance some of which may result from incorrect operation can be put right without contacting the Service Department A Repair work to electrical appliances must only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer cannot be held liable for unauthorised work Check indicators and fault messages Problem Cause and remedy The programme is cancelled 2 22 lights up This is not a fault In some programmes if the drum has been underloaded or is empty the programme will be cancelled T
23. cket e g a timer or a peak load switch off device If the drying programme is interrupted before the end of the cooling down phase this could cause the laundry to self ignite Warning and Safety instructions To prevent the risk of fire the following textiles must not be dried in this tumble dryer Items which have not been washed Items such as workwear which have not been thoroughly cleaned and which are still soiled with grease oil or other deposits such as cosmetics lotions etc If items have not been thoroughly cleaned there is a danger that these might ignite when heated even after they have been removed from the dryer at the end of the programme Items e g mops and floor cloths which have been treated with inflammable cleaning agents or which contain residues of acetone alcohol benzene petrol kerosene stain remover turpentine wax and wax remover or other chemicals Items which have been splashed with hair lacquer hair spray nail varnish remover or similar substances When washing such heavily soiled items ensure that you use sufficient detergent and select a high temperature If in doubt wash the items several times 12 Warning and Safety instructions gt Remove all items from pockets e g lighters matches Warning Do not switch the dryer off before the drying programme has finished If this is done the laundry must be hung up or spread out to cool it down gt Fabric conditi
24. d Limited RD 98 463 631 Level 2 10 College Hill Freemans Bay Auckland 1011 NZ Tel 0800 464 353 nternet www miele co nz Singapore iele Pte Ltd 163 Penang Road 04 03 Winsland House II Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail info miele com sg nternet www miele sg South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 011 875 9000 Fax 011 875 9035 E mail info miele co za nternet www miele co za United Arab Emirates iele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae nternet www miele ae TMB 640 WP C en GB M Nr 10 000 810 00
25. d time during drying Load according to the optimum amount of laundry recommended for the programme being used Underloading is uneconomical Overloading gives a poorer quality of drying and may cause unnecessary creasing Make sure the room temperature is not too high If there are other heat producing appliances in the room in which the dryer is located make sure the room is well ventilated and switch the other appliances off if possible Clean the fluff filters in the door opening after every drying cycle Contents Caring for the environment sssssssssssssseseeeeeeenre enne nnne nnns 2 Warning and Safety instructions 6 Operating the tumble drver eee eeeeee ee eee ee ee eee tena aeaaeeeseeeeeeeeeeeeeee 18 Control Panel se ea en 18 BIER 19 Before using for the first time nnns 20 1 Notes on correct laundry care eee ee eee eeae cee eeeeeeeeeeeeeeeaeaees 21 Points to note regarding washed laundry uuusrssssnnnnnsnnnnnnnnnnnnnnnnnnnnnnnnnn ern anne 21 Preparing the laundry before drying s ssssssasssrassadarrnassiansian aninion saaan ssaa aaa 21 Garment care label symbols AA 22 Laundry care when drying in a tumble dryer uuenessnnsnersessnnnnnnnnnnnnnnnnnnnnnnnnnnnn nn 22 2 Load the tumble drver nnne nnn 23 3 Select a programme and start nm 24 Select a prograrmlrie ee cer prr ru Era inane 24 Select any options or delay start if required sess
26. during selection Perfect Dry indicator With programmes with a selectable drying level the Perfect Dry system calculates the residual moisture present in the laundry to ensure a precise drying result The Perfect Dry indicator Will flash after the programme has started and go out when the programme duration appears in the display Will light up again when the selected drying level is reached and remain on until the end of the programme Will remain dark with the following programmes Woollens handcare Warm air 42 V sensor Touching this symbol will select the drying level required which will then light up 19 Before using for the first time Removing the protective foil and stickers m Remove the protective foil from the door any stickers from the front and the lid A Please do not remove any labels e g the data plate visible when you open the door After installing the dryer A Before using the tumble dryer for the first time ensure that it is installed and connected to the electricity supply correctly If it has not been transported as described in Installation and connection then it must be left to stand for at least 1 hour before it is connected to the electricity supply Follow the procedure for using for the first time outlined in these instructions m Read 1 Notes on correct laundry care and 2 Load the tumble dryer m You can then load t
27. e fragrance m Turn the outer ring clockwise a little m Turn the outer ring clockwise the further you open the flacon the more intense the fragrance Damp laundry and longer drying durations with sufficient heat transfer are needed for the fragrance to be 42 Fragrance flacon released into the laundry effectively The fragrance will also be noticeable in the room air during the process After drying To avoid the fragrance escaping needlessly m Turn the outer ring anti clockwise until marker 2 is in position 9 You will feel a slight resistance If you want to dry laundry without adding fragrance occasionally remove the fragrance flacon and store it in its original packaging until you want to use it again See the following section Replacing the fragrance flacon When the fragrance is no longer sufficiently intense m Turn the outer ring anti clockwise until markers and line up m Replace the fragrance flacon with a new one Fragrance flacons are available to order from Miele or online at www miele shop com 43 Fragrance flacon A Never lay the fragrance flacon down on any surface as the fragrance will leak Only store the fragrance flacon in its original packaging when storing the fragrance flacon in its original packaging whilst you are not using it e g whilst cleaning the tumble dryer to prevent the fragran
28. e flacon must be stored in its packaging so please make sure you retain this gt Caution The fragrance can leak out of the flacon Make sure that you always keep the flacon or the fluff filter with the flacon inserted in it in a horizontal position when carrying and do not tip or place down on any surface gt Use an absorbent cloth to wipe up any fragrance which has leaked out of the flacon onto the floor the dryer or any dryer components e g the fluff filter immediately gt If fragrance which has leaked out of a flacon comes into contact with the skin wash the skin thoroughly with soap and water comes in contact with the eyes rinse the eyes with clean water for at least 15 minutes is swallowed rinse out the mouth thoroughly with clean water Seek medical advice in the case of contact with the eyes or if fragrance has been swallowed gt If fragrance which has leaked out of a flacon comes in contact with clothing change the clothing immediately Wash the clothing or any cloths used for mopping up fragrance thoroughly with plenty of water and detergent There is the risk of fire or damage to the tumble dryer if the following instructions are not observed Never refill a flacon with fragrance Never use a faulty fragrance flacon Dispose of an empty fragrance flacon with the household waste and never use it for any other purpose gt Please also observe the information supplied with the fragrance
29. e side of the door m First take the rubber seal off the door opening and place this to one side m Adjust the position of the door lock So that the screw holes line up with those in the front panel of the dryer m Secure the door lock with the two Torx screws m Usea T20 Torx screwdriver to remove screw EI on the lock catch m Pull off the lock catch together with lock catch cover 61 Installation and connection m Remove the lock catch from the cover This lock catch cover is no longer needed however please keep it ina safe place a gt m insert the lock catch into the new cover supplied with the dryer m Place this new cover to one side for now 62 4 Dismantle the door hinge from the door The door hinge cover must be unclipped from position and then removed m Use a screwdriver to press down gently on position on the door hinge cover m Using a little force pull out door hinge cover H This door hinge cover is no longer needed however please keep it in a safe place Installation and connection 5 Change over the door hinge on the Tip In some circumstances the rods door can be difficult to dislodge Moving the screwdriver with a levering action while pulling at the same time may help to work the rods free The door hinge is secured to the door with 2 angled rods These rods need to be removed with a screwdriver or pointed pliers m Remov
30. e the door hinge and turn it through 180 m Refit the door hinge on the opposite side of the door m insert the end of the screwdriver blade under rod and rotate it so it is in an upright position Do the same to the other rod m Secure the door hinge with the two rods 2 m Position the screwdriver under the end of the rod and then push it into its resting position m Use the screwdriver to guide first one then the other rod 2 to the middle until each can be removed 63 Installation and connection You now need the new door hinge 6 Change the lock catch on the door cover supplied with the dryer You now need the new lock catch cover supplied with the dryer which you have already fitted with the lock catch m Fit new door hinge cover and clip it into position m Push lock catch cover P with its lock catch into position m Tighten screw 64 Installation and connection Refitting 7 Refit the door m Press the rubber seal back into the grove on the door m Position the door in front of the dryer m Fit the base of the door hinge with its 2 pins into the openings on the dryer The base of the door hinge must be flush with the front panel of the dryer The door cannot fall off in this position m Screw the door securely to the dryer at the base of door hinge Now that you have changed the door hinging the door will open from the opposite
31. eal when doing this become damaged m Check whether the cooling fins are blocked with fluff as follows m Carefully vacuum up any visible fluff or soiling 38 Cleaning and care Replacing the plinth filter m Close the heat exchanger access panel A The dryer can only be operated with the plinth filter fitted correctly and the heat exchanger access panel closed The access panel must be closed correctly to ensure that water cannot leak from the condenser system and to ensure that the dryer functions efficiently m Fit the filter back on the handle Make sure it is the correct way round To ensure that the filter is positioned correctly in the front of the heat exchanger unit m First insert the handle with the plinth filter attached over the two guide pins The word Miele on the handle must be the correct way up m Push the plinth filter in completely The act of pushing in the plinth filter will also push in the right hand guide pin 39 Cleaning and care Tumble dryer A Disconnect the tumble dryer from the mains electricity supply A Do not use solvents abrasive cleaners glass cleaners or all purpose cleaners These could damage plastic surfaces and other parts m Clean the tumble dryer with a slightly damp cloth and a mild non abrasive cleaning agent or a solution of washing up liquid and water m Clean the seal around the inside of the door with a damp cloth
32. er Four height adjustable screw feet empty after every drying cycle Cool air intake grille Door do not obstruct with a laundry do not open during drying basket or other objects Hose for external drainage of condensed water 52 Installation and connection Rear view Protruding lid for holding when moving the dryer see arrows 2 Accessories for external drainage of condensed water hose clip adapter and hose holder 3 Hose for external drainage of condensed water Mains connection cable Transporting the dryer To manoeuvre the dryer out of its packing case to its installation site hold it by the front feet and the lid where it protrudes at the back of the appliance A Only transport the dryer as shown in the following illustrations A If transporting the dryer at an angle only tip towards the left side A If the tumble dryer has not been transported as described then it must be left to stand for at least 1 hour before it is connected to the electricity supply Otherwise the heat pump can be damaged 53 Installation and connection Installation Levelling the dryer A Make sure the dryer door can be opened without hindrance after installation The appliance must stand perfectly level to ensure safe and proper operation The screw feet can be adjusted to compensate for
33. f they are supervised whilst using it or have been shown how to use it in a safe way and understand and recognise the consequences of incorrect operation Safety with children Children under 8 years of age must be kept away from the tumble dryer unless they are constantly supervised Children 8 years and older may only use the tumble dryer unsupervised if they have been shown how to use it safely and recognise and understand the consequences of incorrect operation Children must not be allowed to clean or maintain the tumble dryer unsupervised gt Please supervise children in the vicinity of the tumble dryer and do not let them play with it Warning and Safety instructions Technical safety gt Before setting up the tumble dryer check it for any externally visible damage Do not install or use a damaged tumble dryer Before connecting the tumble dryer ensure that the connection data on the data plate fuse rating voltage and frequency match the mains electricity supply If in any doubt consult a qualified electrician Reliable and safe operation of this tumble dryer can only be assured if it has been connected to the mains electricity supply The electrical safety of this tumble dryer can only be guaranteed when correctly earthed It is essential that this standard safety requirement is met If in any doubt please have the household wiring system tested by a qualified electrician Miele cannot be
34. flacon 16 Warning and Safety instructions Accessories Only use genuine Miele original spare parts and accessories with this appliance If non Miele parts are used guarantee performance and product liability claims will be invalidated The tumble dryer can be combined with a Miele washing machine in a washer dryer stack The appropriate WTV stacking kit available to order to match your tumble dryer and washing machine is required If you order a plinth for this tumble dryer available from Miele as an optional accessory depending on country make sure it is the correct one Z Miele cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Operating the tumble dryer Control panel Gentle tumble Cottons Delicates gt Cottons St n Gentle smoothing Anti crease Minimum iron Denim J Woollens AS Outerwear handcare N Warm air Proofing Display with and V sensors See the following page for more information 2 Start Stop button For starting the programme selected and cancelling a programme once it has started 3 Option buttons 18 Various options can be added to the programmes 4 Programme selector For selecting the programme Optical interface For service technicians button The tumble dryer is switched on and off by pressing this button To save energy the dryer
35. gramme can be extended for all programmes with selectable drying levels This makes the garments easier to handle Options 00 factory default G cool down time 2 min longer G2 cool down time 4 min longer G3 cool down time 6 min longer 04 cool down time 8 min longer G5 cool down time 10 min longer 06 cool down time 12 min longer 01 cool down time 14 min longer 08 cool down time 16 min longer 09 cool down time 18 min longer POS Buzzer volume The buzzer can be set so that it is louder Ol Factory default HO Buzzer louder POG Keypad tone When this function is activated a tone will sound each time a button is pressed The volume of the keypad tone will depend on the setting selected for P25 Buzzer volume Options 00 Factory default off G Keypad tone on 73 Programmable functions POT Code The code prevents your dryer being used without your knowledge When the code has been activated you have to enter a code after switching the dryer on Otherwise the dryer cannot be operated Options UU Factory default off O1 Code on If option 8f has been selected after switching on you will have to enter the code before you can operate the dryer To use the dryer when the code is activated After the dryer has been switched on Will flash in the time display The code is 250 and cannot be altered m Touch the lt gt sensor
36. grance flacon m from the surfaces of all the fluff filters m fromthe perforated laundry deflector m Push the upper fluff filter back into position until it clicks m Pull the upper fluff filter forwards to remove it m Close the door If there is a great deal of compacted fluff carry out the following procedure 35 Cleaning and care Cleaning the fluff filters and air flow openings thoroughly If the drying duration has become longer or the surface of the filters is visibly compacted with fluff you should carry out the following cleaning procedure A If using a fragrance flacon make sure you remove it beforehand m Pull the upper fluff filter forwards to remove it m Turn the yellow dial on the lower fluff filter in the direction of the arrow until you hear it click 36 m Hold the dial and pull the fluff filter forwards to remove it m Use a vacuum cleaner with a long crevice nozzle attached to remove any visible fluff from the upper air flow openings Cleaning the fluff filters with water m Flush the fluff filters through with hot running water m Shake the fluff filters thoroughly and then dry them carefully A Ensure the filters are dry before replacing them Wet filters could cause operational faults m Push the lower fluff filter in completely and lock it with the yellow dial m Push the upper fluff filter in completely m Close the door Cleaning a
37. he dryer and select a programme as described in 3 Select a programme and start it 20 1 Notes on correct laundry care Points to note regarding washed laundry When washing very heavily soiled items ensure that you use sufficient detergent and select a high temperature If in doubt wash the items several times Do not put soaking wet items into the tumble dryer Make sure your laundry is thoroughly spun before drying The higher the spin speed the greater the savings that can be made in energy and time during drying New dark coloured garments should be washed and dried separately from light coloured garments to avoid the danger of colours running and discolouring other garments or even plastic components in the dryer Dark coloured fibres can also settle on light coloured garments and vice versa Starched laundry can be dried in the tumble dryer To achieve the usual finish double the amount of starch should be used Preparing the laundry before drying A Make sure that any objects e g detergent dosing balls lighters etc have been removed from the laundry They could melt or explode and cause damage to the dryer or the laundry UN See Warning and Safety instructions for further information Loading or using the tumble dryer incorrectly could cause a fire Sort the laundry according to the type of fibre and weave size garment care label symbol and the drying level required
38. his can also happen if the items are already dry m Open and close the door to resume drying m Dry individual items using the Warm air timed drying programme flashes lights up after the tumble dryer has been switched on and a programme cannot be selected Access via a code has been activated m See Programmable functions P27 Code and FXX e g F35 light up after a programme has been cancelled No obvious cause m Switch the dryer off and then on again m Start a programme If the programme is cancelled again and an error message appears there is a fault Contact the Miele Service Department 45 Problem solving guide Problem Cause and remedy lights up at the end of a programme There is a build up of fluff in the airways m Clean the fluff filters m Clean the plinth filter See Cleaning and care To switch off m Switch the dryer off and back on again and 355 light up after a programme has been cancelled An excessive amount of fluff has built up m Clean the fluff filters m Clean the plinth filter Clean the airways Clean the area underneath the plinth filter Clean the heat exchanger To switch off m Switch the dryer off and back on again lights up after a programme has been cancelled The condensed water container is full or there is kink in the drain hose m Empty the container m Check the drain hose To sw
39. il a suitable replacement is obtained The colour of the correct replacement cover is that of the coloured insert in the base of the plug or the colour that is embossed in words on the base of the plug as applicable to the design of plug fitted Replacement fuses should be ASTA approved to BS 1362 and have the correct rating Replacement fuses and fuse covers may be purchased from your local electrical supplier WARNING THIS APPLIANCE MUST BE EARTHED Consumption data Load Final spin Residual Energy Duration speed in a moisture domestic washing machine kg rpm 96 kWh min Cottons 4 f 8 0 1000 60 1 94 156 4 0 1000 60 1 10 92 Cottons Normal 8 0 1200 53 1 75 141 8 0 1400 50 1 65 134 8 0 1600 44 1 45 119 Cottons Normal Gentle tumble 8 0 1000 60 1 96 163 Cottons Hand iron 8 0 1000 60 1 58 125 8 0 1200 53 1 40 109 8 0 1400 50 1 30 102 8 0 1600 44 1 10 87 Minimum iron Normal 4 0 1200 40 0 61 55 Gentle tumble 4 0 1200 40 0 61 55 Minimum iron Hand iron 4 0 1200 40 0 50 48 Denim Normal 3 0 900 60 1 28 100 1 Weight of dry laundry 2 Test programme in accordance with Regulation 392 2012 EU for energy labelling measured in accordance with EN 61121 All data was calculated using EN 61121 unless otherwise stated Power consumption when switched off Power consumption when not switched off Note for test institutes 0 15 W 1 50 W For testing in accordance with EN 6112
40. itch off m Open and close the door while the dryer is Switched on G lights up The programme selector has been moved m Select the original programme The time remaining will appear in the display again Bars flash in the display at the end of a programme Li The programme has finished but the laundry has not yet cooled down m Either remove the laundry and spread it out to cool down or leave it in the tumble dryer to cool down during the cooling phase 46 Problem solving guide Unsatisfactory drying results Problem Cause and remedy The laundry is not sufficiently dry The load consisted of different types of fabric m Finish drying using the Warm air timed drying programme m Select a different programme next time Tip You can alter the drying levels for some programmes see Programmable functions Laundry or feather filled pillows smell after drying The laundry was washed with insufficient detergent Feathers are a natural product and this is quite normal m Laundry use sufficient detergent next time m Pillows take out of the tumble dryer and air them m Use a fragrance flacon available as an optional accessory for your favourite fragrance Items made of synthetic fibres are charged with static electricity after drying Synthetic fibres tend to attract static charge m Static charge can be reduced by adding a fabric conditioner to the final rin
41. levels then the following are lit up additional drying level is selected Extra dry Normal Normal dryer than Normal Normal Slightly dry Hand iron damper than Normal Hand iron Hand iron 66 Machine iron damper than Hand iron Please see Programmable functions POS Additional drying levels 3 Select a programme and start it Other programmes and the timed Select any options or delay drying programmes start if required Cottons Woollens handcare Proofing Please see Options for further information The drying level is preset and cannot be altered To select options Warm air Gentle tumble C You can select the duration in ten minute stages Anti crease m Buzzer G zz m Press a button The button will light up when the option is selected m Touch the lt gt sensor repeatedly until the programme duration you want appears in the time display amp will flash You can select the duration in ten minute stages from 4 22 minutes up to 2 00 hours 25 3 Select a programme and start it Delay start You can delay the start of the programme However delay start cannot be used with the Warm air programme m Touch the sensor amp will flash Please see Delay start for more information Start the programme m Press the flashing Start Stop button The Start Stop button will now light up con
42. m Dry all parts with a soft cloth m The drum and other stainless steel parts can be cleaned with a suitable proprietary stainless steel cleaner following the manufacturer s instructions 40 Fragrance flacon Using a fragrance flacon optional accessory will add a pleasant fragrance to your laundry A Before using a fragrance flacon please read Warning and safety instructions Using a fragrance flacon optional accessory Inserting a fragrance flacon Only hold the fragrance flacon as illustrated Do not hold it at an angle or tip it as the fragrance will leak out of the flacon m Open the cover using the tab until the tab is at the top right hand side as shown m Hold the flacon securely to prevent opening it by mistake m Pull off the protective seal m Open the door of the tumble dryer The fragrance flacon is inserted in the upper fluff filter in the opening on the right hand side beside the grip If you are not using a fragrance flacon the cover must always remain closed push the cover down completely with the tab m Insert the flacon in the opening as far as it will go 41 Fragrance flacon You will feel a slight resistance and Mark t li ith arkers and must line up wi hear aedi ciuis one another Marker 2 must be in position 9 this is the position at which you can feel a resistance Before drying You can select the intensity of th
43. mme m Select a programme with selectable drying levels m Touch the V sensor until two drying levels light up in the display if 2 drying levels then the following are lit up additional drying level is selected Extra dry Normal Normal Normal Slightly dry Hand iron Hand iron Hand iron 66 Machine iron 75 Programmable functions Pil Standby To switch the display and buttons back on again Turn the programme selector or press a button Neither will have any effect if a programme is running To save energy the display and buttons will go out after 10 minutes and only the Start Stop button will flash slowly You can alter this setting Open the door while the dryer is However standby mode will not occur switched on in the event of a fault Options g Standby switched on The display and buttons will go out after 10 minutes if no selection is made after switching the dryer on after a programme has started However the display and buttons will remain lit up for 10 minutes after a delay start time has elapsed after the end of the programme or at the end of the anti crease phase The buzzer if selected will sound for 10 minutes after the end of the programme Not in current programme factory default setting As described under 52 However the display and buttons will remain lit up during the programme 00 Off The display and buttons
44. nd care Plinth filter Only clean the plinth filter when the amp indicator lights up To delete the indicator switch the dryer off and back on again Removing the plinth filter m Press the round indented area on the heat exchanger access panel to open it The panel will spring open m Pull the plinth filter out by the handle Removing the plinth filter will cause the right hand guide pin in the dryer to come out This pin ensures that the heat exchanger access panel can only be closed if the plinth filter is inserted the right way round Cleaning the plinth filter m Pull the handle out of the plinth filter m Clean the filter thoroughly under running water m Squeeze the plinth filter thoroughly A The plinth filter must not be replaced dripping wet as this can cause a fault m Use a damp cloth to remove any fluff from the handle 37 Cleaning and care Cleaning the plinth filter panel Checking the condenser unit A Danger of injury Do not touch the cooling fins You could cut yourself m Look to see if fluff has accumulated If there is visible soiling A Clean using a vacuum cleaner with a dusting brush attached Carefully pass the vacuum cleaner brush over the heat exchanger cooling fins without applying any m Use a damp cloth to remove any fluff pressure Otherwise the cooling fins Make sure that you do not damage could be bent out of shape or the rubber s
45. nge marker m Unfold the laundry and load loosely into the drum Do not overload the drum Overloading can cause unnecessary wear and tear to the laundry give a disappointing drying result and cause more creasing When closing the door make sure that laundry does not get trapped in the door opening This could damage the laundry If you are not using a fragrance flacon the tab must be pushed down completely see arrow Close the door m Shut the door with a gentle swing 23 3 Select a programme and start it Select a programme Cottons Y Delicates Cottons Gentle smoothing Minimum iron Denim Woolens 1 Outerwear handcare Warm air J Proofing m Turn the programme selector A drying level or option buttons may also light up and durations will appear in the time display Programmes with drying levels Cottons Minimum iron Delicates Denim Outerwear Gentle smoothing The drying level can be altered after selecting one of these programmes Extra dry Normal Hand iron Machine iron m Touch the V sensor to select the drying level required 24 Any drying level can be selected for the Cottons programme A more limited range is available when using the other programmes Additional drying levels Tip Using the programmable functions you can activate deactivate additional drying levels if 2 drying
46. nk m Secure the non return valve using hose clips 59 Installation and connection Changing the door hinging You can change the door hinging on this tumble dryer yourself A For safety reasons the tumble dryer must be disconnected from the electricity supply before changing the door hinging You will need a Torx T20 and T30 screwdriver a flat head screwdriver or pointed pliers the lock catch cover supplied the door hinge cover supplied a soft surface e g a tablecloth Changing the hinging over 1 Remove the door from the dryer m Open the door m Usea T30 Torx screwdriver to unscrew the two screws on the base plate of the door hinge 9 The door cannot fall off as it is held in place by 2 pins 60 m Hold the door securely and pull it forwards to remove the door you will need to pull the base plate of the hinge with its 2 pins out of the dryer To avoid scratching the door place it outer side downwards on a soft surface e g a tablecloth 2 Change over the door lock on the dryer m Use a Torx T30 screwdriver to unscrew the two screws on the door lock m Use the screwdriver to press the door lock upwards The door lock will spring out of its position and can then be removed Installation and connection m Turn the door lock through 180 3 Remove the lock catch from the door m Press the door lock into openings on the opposit
47. of this booklet N B A call out fee will be charged for service visits where the problem could have been resolved as described in these instructions When contacting the Service Department please quote the model and serial numbers both of which are given on the data plate visible when the door is open Please note that telephone calls may be monitored or recorded for training purposes Optional accessories Optional accessories for this tumble dryer are available from Miele your Miele dealer or via the internet at Miele www miele shop com Dryer basket The dryer basket is suspended in the drum and does not rotate with the drum This enables items which must not be subjected to mechanical action to be dried or aired Fragrance flacon A fragrance flacon can be used in your tumble dryer to add a pleasant fragrance to your laundry Guarantee U K In the U K the appliance is guaranteed for 2 years from the date of purchase However you must activate your cover by calling 0330 160 6640 or registering online at www miele co uk Guarantee Other countries For information on the appliance guarantee specific to your country please contact Miele See end of this booklet for contact details 51 Installation and connection Front view Mains connection cable 8 Heat exchanger access panel 2 Control panel do not open during drying Condensed water contain
48. oner and similar products must be used according to the instructions on the manufacturer s packaging To prevent the risk of fire the following textiles must not be dried in this tumble dryer tems which have been cleaned using chemicals e g professional dry cleaning agents Items which contain a large proportion of rubber foam rubber or rubber like materials For example products made from latex foam rubber shower caps waterproof textiles rubberised articles and items of clothing and pillows with foam rubber filling Damaged items which contain padding or fillings e g pillows jackets When damaged the filling can get out with the risk of it igniting in the dryer Warning and Safety instructions In many programmes the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them this also avoids the danger of the laundry self igniting The programme is not finished until the cooling down phase has been completed As soon as the programme has finished remove all laundry from the drum gt Do not let anyone sit or lean on the door as this can cause the tumble dryer to tip up Always close the door after use This way you will avoid the danger of Children climbing onto or into the dryer or hiding things in it Pets or other small animals climbing into it gt The tumble dryer must not be used without fluff filters or
49. rease esee nennen essen neris andanan saana eser aaa aaan 77 Warning and Safety instructions LLI P It is essential to read these instructions This tumble dryer complies with current safety requirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the tumble dryer please read these instructions carefully before using it for the first time They contain important information on its safety installation use and maintenance Keep these instructions in a safe place and ensure that new users are familiar with the content Pass them on to any future owner Correct application This tumble dryer is intended for use in domestic households and similar working and residential environments gt This tumble dryer is not intended for outdoor use gt It must be used only as a domestic appliance to dry items which have been washed in a water solution and which are marked on the manufacturer s care label as being suitable for tumble drying If using dry cleaning kits do so at your own risk and follow the instructions provided on the packaging Any other applications may be dangerous Miele cannot be held liable for damage resulting from incorrect or improper use or operation Warning and Safety instructions This tumble dryer can only be used by people with reduced physical sensory or mental capabilities or lack of experience or knowledge i
50. rs in the door opening see Cleaning and care Fluff filters m Shut the door with a gentle swing m Empty the condensed water container 27 Options Gentle tumble Selectable options Les Gentle tumble Anti crease Anti crease Buzz Les A er Cottons x X Cottons X X X Buzzer Hz Minimum iron X X X Woollens X The options are switched on or off by handcare pressing the appropriate button TS Warm air X X X The button will light up when the option is selected Delicates 6 X X Gentle 0 X X Gentle tumble smoothing Delicate fabric with the H symbol on Denim X X X the care label e g acrylic garments is dried at a lower temperature The Outerwear Oo X X programme duration is longer Proofing i X X Anti crease X Can be selected O Cannot be changed always active Depending on the programme selected Cannot be selected the drum will continue to rotate in a special rhythm for up to 2 hours at the end of the programme to reduce creasing if you do not wish to remove the laundry immediately Buzzer A buzzer four beeps at intervals for a maximum of 1 hour will sound to let you know that the programme has finished The continuous buzzer which sounds when there is a fault is not dependent on the setting for the buzzer at the end of the programme 28 Delay start To select delay start With delay start you can delay the
51. rs jackets shirts Note Suitable for dry and damp laundry Select Hand iron if the items are to be ironed after drying Smooths out creasing caused during the spin cycle in the washing machine Remove garments as soon as the programme has finished Denim Max load 3 0 kg Normal Hand iron Use for Denim garments e g jeans jackets skirts shirts Outerwear Max load 2 5 kg Normal Hand iron 6 Use for Outerwear which is suitable for drying in a tumble dryer Proofing Max load 2 5 kg Normal Use for Drying microfibre fabric skiwear outerwear fine closeweave cotton garments poplin or tablecloths which are suitable for drying in a tumble dryer and have been treated to provide a water and dirt resistant finish Notes This programme includes a proofing fixing phase Only use proofing agents containing fluorochemical compounds which are stated by the manufacturer as being suitable for use on membrane textiles Do not dry items which have been treated with proofing agents containing paraffin Fire hazard Weight of dry laundry 32 Changing the programme sequence You cannot change to another programme once a programme has started this prevents unintentional alterations If you move the programme selector G will light up until you move the programme selector back to the original programme You will need to cancel the curren
52. se described below require the fitting of a non return valve Maximum delivery head with non return valve fitted 1 00 m Installation conditions requiring the fitting of a non return valve Drainage into a sink or floor gully where the end of the hose is immersed in water Connection to a sink drain outlet Connection to a drainage system already in use by another appliance e g a dishwasher or washing machine A The non return valve has to be fitted with the arrow pointing in the direction of flow Otherwise water will not drain out of the appliance Installation and connection Arranging the drain hose A Do not pull on the drain hose and do not stretch it or allow it to become kinked This could damage the hose There will be a small amount of residual water left in the drain hose Have a container ready to collect this m Guide the hose to the right or left side of the dryer as required f you are guiding it to the right you can fit the hose into the groove Leave the hose in the lower holder to prevent it from being kinked by mistake m Pull the drain hose off its connection m Unwind the hose and pull it carefully out of the holders m Allow any residual water to run into the container 57 Installation and connection Examples Drainage into a sink or floor gully Use the hose holder to prevent the drain hose from becoming kinked m Pre
53. se in the washing programme There is a build up of fluff Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed Machine drying hardly causes any fluff to form Fluff is collected by the fluff filters and the plinth filter and can be removed easily m See Cleaning and care 47 Problem solving guide Other problems Problem Cause and remedy The drying process goes on too long or even switches off The room in which the dryer is located is too warm m Ventilate the room thoroughly Detergent residues hair and fine fluff can clog the filters m Clean the fluff filters and the plinth filter m Remove any visible fluff bottom left from behind the panel in the heat exchanger cavity see Cleaning and care from the cooling fins behind the grille bottom right see the end of this section The cool air intake bottom right grille is blocked m Move any objects such as a laundry basket away from the dryer The fluff filters and the plinth filter were wet when replaced m The fluff filters and the plinth filter must be dry The laundry is too damp m Spin using a higher spin speed in the washing machine The tumble dryer has been overloaded m Do not exceed the maximum load for the programme selected Metal zips have prevented the dryer from registering the correct moisture level m Open
54. ss the small catches on the left and right of the hose holder with your thumbs black arrows and m pull the hose holder forwards to remove it white arrows A If you want to drain the water off into a sink or basin you will need to secure the hose carefully e g by tying it to a tap to make sure it cannot slip during use see the drawing under Installation and connection Front view Overflowing water can cause damage m The non return valve can be fitted in the end of the hose You can refit the hose holder at a later stage if you decide that you no longer want to drain the condensed water externally 58 Direct connection to a sink drain outlet m Remove the following from the back of the dryer at the top Adapter 1 and hose clip 3 behind it m Connect the drain hose as described below Installation and connection 1 Adapter 2 Nut 3 Hose clip 4 End of the hose secured with the hose holder 5 Non return valve 6 Tumble dryer drain hose m Fit adapter 1 to the sink drain outlet using nut 2 The nut is usually fitted with a washer which must be removed m Attach the end of the hose 4 to adapter 1 m Use the hose holder m Use a screwdriver to tighten hose clip 3 up close to the nut m Fit non return valve 5 to tumble dryer drain hose 6 Non return valve 5 has to be fitted so that the arrow points in the direction of flow i e towards the si
55. stantly The Perfect Dry indicator will only flash light up with programmes with selectable drying levels see also Operating the tumble dryer The laundry will be cooled down shortly before the end of the programme 26 4 Remove the laundry End of programme Anti crease At the end of the programme 8 00 will light up in the display and the Start Stop button will go out The anti crease function if selected will then switch on for a maximum of 2 hours 10 minutes after the end of the programme the Start Stop button will begin to flash slowly and the display will go out this is Standby mode to save energy The dryer will switch off automatically 15 minutes after the end of the anti crease phase with programmes without an anti crease phase it will switch off 15 minutes after the end of the programme Remove the laundry A Never open the door before the drying process has finished m Pull the door open at the side with the orange marker m Remove the laundry Check that all items have been removed from the drum If items are left in the dryer they could be damaged by overdrying when the dryer is next used If the dryer is switched on at the mains and the door is opened the drum lighting will come on It will go out a few minutes later to save energy m f the dryer is still switched on switch it off with the D button A buzzer will sound m Remove the fluff from the 2 fluff filte
56. start of the programme by up to a maximum of 24 hours However delay start cannot be used with the Warm air programme m After selecting the programme touch the lt gt sensor amp will flash Times of up to D are selected in 2 30 minute stages and then in hour stages up to 24h If you touch the sensor continuously the time will count up to 24 Touching the 244 sensor again when 4 shows in the display will delete the time selected To begin delay start m Press the Start Stop button amp will light up Delay start times of more than h will count down in hours and then in minutes until the start of the programme The drum will turn briefly every hour until the start of the programme to reduce creasing To change delay start after it has started counting down m Press the Start Stop button will flash m Touch the lt gt sensor to change the time m Press the Start Stop button To add remove laundry after delay start has started counting down m You can open the door to add remove laundry All programme settings will be saved will flash You can also change the drying level if required m Press the Start Stop button so that the delay start time continues to count down To cancel delay start m Switch the dryer off and then on again 29 Programme chart Cottons Inn Max load 8 0 kg Use for Cotton items such
57. t 2 hour anti crease 77 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Customer Contact Centre Tel 0330 160 6600 E mail mielecare miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 1300 464 353 Internet www miele com au China Miele Shanghai Trading Ltd 1 3 Floor No 82 Shi Men Yi Road Jing an District 200040 Shanghai PRC Tel 86 21 6157 3500 Fax 86 21 6157 3511 E mail info miele cn Internet www miele cn Miele Hong Kong Limited 41 F 4101 Manhattan Place 23 Wang Tai Road Kowloon Bay Hong Kong Tel 852 2610 1331 Fax 852 2610 1013 Email mielehk miele com hk India Miele India Pvt Ltd Ground Floor Copia Corporate Suites Plot No 9 Jasola New Delhi 110025 Tel 011 46 900 000 Fax 011 46 900 001 E mail customercare miele in Internet www miele in Ireland Miele Ireland Ltd 2024 Bianconi Avenue Citywest Business Campus Dublin 24 Tel 01 461 07 10 Fax 01 461 07 97 E Mail info miele ie Internet www miele ie Manufacturer Miele amp Cie KG Carl Miele StraBe 29 33332 G tersloh Germany Malaysia iele Sdn Bhd Suite 12 2 Level 12 enara Sapura Kencana Petroleum Solaris Dutamas No 1 Jalan Dutamas 1 50480 Kuala Lumpur Malaysia Phone 603 6209 0288 Fax 4603 6205 3768 New Zealand iele New Zealan
58. t programme before you can select a new one Cancelling a programme while it is running and selecting a new programme m Press the Start Stop button The items will be cooled down depending on the temperature reached and how long they have been dried for 2 59 will light up if you press the Start Stop button again during this cooling down phase m Press the D button to switch the dryer off m Press the D button to switch the dryer on m Select and start a new programme straight away Adding or removing laundry after a programme has started m Press the Start Stop button The items will be cooled down depending on the temperature reached and how long they have been dried for 2 00 will light up if you press the Start Stop button again during this cooling down phase A Danger of burning Do not touch the back of the drum when adding or removing items The drum and the items can be very hot m Add or remove items m Close the door To continue with the programme select a drying level first of all if necessary m Press the Start Stop button Programme duration Altering the programme sequence can cause the programme duration shown in the time display to be adjusted 33 Cleaning and care Emptying the condensed water container The condensed water is collected in the condensed water container Empty the condensed water container after every drying programme The indica
59. tor will light up if the maximum level of the condensed water container is reached To delete the indicator open and close the door with the dryer switched on A To prevent damaging the door and the front of the condensed water container when pulling the container out of the dryer always close the door completely This does not apply to right hand hinged models m Pull out the condensed water container 34 m To prevent water running out hold it at the front and towards the back and keep it in a horizontal position when carrying it m Empty the container m Replace the container in the dryer A Condensed water should not be consumed It could lead to health problems for people and animals Condensed water can be put to household use e g used in a steam iron or humidifier To ensure that any residual particles of fluff in the condensed water are removed before use pass it through a fine sieve or paper filter first Cleaning and care Fluff filters This tumble dryer has 2 fluff filters in the door opening the upper and lower fluff filters trap fluff produced during the drying process Removing visible fluff Remove any fluff after every drying cycle Tip You can also use a vacuum cleaner so that you can remove the fluff without m Remove the fluff see arrows e touching it m Open the door A You must remove the fragrance flacon if present beforehand See Fra
60. u take it out of the dryer Machine iron if the laundry e g table linen requires further processing after drying 22 Down filled garments have linings which have a tendency to shrink depending on the quality of the item They can be partially dried using the Gentle smoothing programme Pure linen should only be machine dried if specified as suitable by the manufacturer on the care label as the surface of the fabric may otherwise become rough They can be partially dried using the Gentle smoothing programme Woollens and wool blends tend to become matted and shrink if dried in a tumble dryer They can however be fluffed up in the Woollens handcare programme Loopknit garments e g T shirts and underwear tend to shrink depending on their quality Do not over dry these textiles When purchasing these garments it is advisable to take their shrinkage properties into account Select the Gentle tumble option for fabric which is particularly heat sensitive or susceptible to creasing 2 Load the tumble dryer A It is essential to read 1 Notes on correct laundry care first of all m Press the D button to switch the dryer on The interior drum lighting will come on The interior drum lighting will automatically go out after a few minutes and or after the start of a programme to save energy Open the door m Pull the door open at the side with the ora
Download Pdf Manuals
Related Search