Beko DRVT71W tumble dryer
Contents
1. 12 Correct load capacity 12 Loading 12 6 Selecting a Programme and Operating Your Machine 13 Control panel 13 Preparing the machine 14 Timer programme selection 14 Main programmes 14 Programme selection and consumption table 15 Auxiliary fUNCtION o 16 Warning indicators 16 Starting the Programme 16 Timer follow up indicator 16 Changing the programme after the programme has started 16 Child proof OK ana aan 16 Ending the programme through canceling sisi a A 17 End of programme 17 7 Quick instructions for daily use 1 8 Maintenance and cleaning 19 Flat filter ss dee onde ban ana 19 9 Solution suggestions for problems 20 10 Door Reversal 21 11 Guarantee 22 What is covered ccecce 22 What is not covered 22 Important notes 22 12 Service 23 3 EN Your Dryer Overview 1 Rating label 4 Adjustable Feet 2 Control Panel 5 Power Cord 3 Fluff filter 4 EN Technical Specifications EN eight ret oltage Rated power input See rating label Type label is located behind the loading door Specifications of this appliance may change without notice to improve the guality of the product Figures in this manual2. cleaned out with a vacuum cleaner every Six months 19 EN 9 Solution suggestions for problems Problem Cause Explanation Suggestion Drying process takes too much time The filter might have not been cleaned Meshes of the filter may be clogged Wash with water Laundry comes out wet at the end of drying The filter might have not been cleaned Excessive laundry might have been loaded in Meshes of the filter may be clogged Wash with water Do not overload the machine Machine does not switch on or the programme does not start Machine is not activated when set Programme has been interrupted without any cause It might have not been plugged in The loading door may be ajar Programme might have not been set or the Start Pause Cancel button might have not been pressed Childproof lock might have been activated The condenser cover on the models with a condenser might not be closed securely The loading door may be ajar Electricity may be cut off Make sure that the machine is plugged in Make sure that the loading door is properly closed Make sure that the programme has been set and it is not in Pause mode Deactivate the childproof lock Make sure that the condenser cover and the red lock is closed securely Make sure that the loading door is properly closed Press Start Pause Cancel button to
3. start the programme Laundry has shrunk become felted or deteriorated A programme suitable for the laundry type might have not been used Dry only the laundry which is suitable for drying in your machine after checking the labels on your clothes Select a programme with suitable low temperature for the laundry type to dry your clothes Drum light does not come on for models equipped with a amp The machine might have not been started by using the On Off button Bulb may have blown Make sure that the machine is On Call the authorized service to replace the bulb 0 Anti creasing LED flashes The 2 hour anti creasing programme to prevent laundry from creasing might have been activated Turn off the machine and take out the laundry 0 Anti creasing LED is on Programme has come to an end Turn off the machine and take out the laundry Filter cleaning LED flashes Filter might have not been cleaned Clean the cover filter A Call an authorised service agent if the problem persists 20 EN 10 Door Reversal 1 Unplug the dryer 2 Open the door 8 Turn the contact pin in the upper part of door by 90 in the anti clockwise direction and remove it 4 Unscrew the 2 screws of each door hinge and remove the door 5 Removing the door lock Using a flat screwdriver release the snap fitted door lock 6 Remove 2 plugs
4. Press the On Off button to shut down the machine GIA 2 hour anti creasing programme to prevent laundry from creasing will be activated if you do not take the laundry out after the programme has come to an end Clean the filter after each drying please see Filter cleaning 17 EN 7 Quick instructions for daily use Preparation and starting 1 Press the On Off button 2 Place the laundry in the machine 8 Select the programme 4 Close the loading door 5 Press Start Pause Cancel button Cancelling a programme A new programme can be selected and started after Programme cancel is activated in order to change the drying programme In order to cancel the selected programme press Start Pause Cancel button for about 3 seconds The Filter cleaning and O Anti creasing warning LEDs will light up at the end of this period for reminding purposes Adding laundry In order to add laundry after the start up of the programme 1 Press Start Pause Cancel button 2 Open the loading door and put the laundry in 8 Close the loading door 4 Press Start Pause Cancel button to start the programme Changing the programme after the programme has started You can use this feature after your machine has started to dry your clothes under higher or lower temperatures Press and hold the Start Pause Cancel button for about 3 seconds to switch the machine into the
5. before being dried in the dryer Garments or pillows bolstered with rubber foam latex foam shower bonnets water resistant textiles materials with rubber reinforcement and rubber foam pads should not be dried in the dryer Do not use fabric softeners and anti static products unless they are recommended by the manufacturers of the fabric softener or the product This product must be earthed Grounding installation decreases the risk of electric shock by opening a path with low resistance for the electricity flow in case of a malfunction or failure Power cable of this product is equipped with a conductor and a grounding plug that allows for grounding the product This plug must be installed appropriately and inserted into a socket which is grounded in accordance with the local laws and regulations Do not install the product behind a door with a lock sliding door or a door that has a hinge against the hinge of the dryer Do not install or leave this product in places where it will be exposed to outdoor conditions Do not tamper with the controls Do not perform any repair or part replacing procedures on the product even if you know or have the ability to perform unless it is clearly suggested in the operating instructions or the published service manual Inside and exhaust duct of the product must be cleaned by the qualified service personnel periodically Wrong connection of grounding conductor of the product can ca
6. button is pressed if the dryer is energized sure that you select the appropriate programme D O KA QI Sutan for Do not dry with drier Normal emperaire tempere Hang without Dry ona honey Spinning hanger PP Can be ironed Can Do not iron with hot iron ironed vith warm iron Laundry unsuitable for drying in the machine e Laundry items with metal attachments such as belt buckles and metal buttons can damage your dryer e Do not dry items such as woollens silk garments and nylon stockings delicate embroidered fabrics laundry with metal accessories and items such as sleeping bags in the dryer e Laundry made of delicate and valuable fabrics as well as lace curtains can be creased Do not dry them in the dryer e Do not dry items made of hermetic fibres such as pillows and quilts in the dryer e Laundry made of foam or rubber will be deformed e Do not dry laundry containing rubber in the dryer e Do not dry laundry exposed to petroleum oil combustible or explosive agents in the dryer even if they are washed beforehand e Overly wet laundry or laundry with dripping water must not be put into the dryer e Items cleaned or washed with gasoil fuel oil dry laundry solvents and other combustible or explosive materials as well as the items that are contaminated or spotted with such materials should laundry labels Dry only the laundry not be dried in the product since the
7. for the exhaust fumes of the devices operating with gas or other types of fuel e You must provide enough ventilation in order to prevent gases exiting from devices operating with other types of fuels including the naked flame from accumulating in the room due to the back fire effect e Always clean the lint filter before or after each loading e Never operate your dryer without the lint filter installed e Do not allow fibre dust and dirt accumulation around the exhaust exit and at adjacent areas e Power cable plug must be within easy reach after installation 6 EN Do not use extension cords multi plugs or adaptors to connect the dryer to power supply in order to decrease the risk of electric shock Do not make any changes on the plug supplied with the product If it is not compatible with the socket have a qualified electrician change the socket with a suitable one Items cleaned or washed with gasoil fuel oil dry laundry solvents and other combustible or explosive materials as well as the items that are contaminated or spotted with such materials should not be dried in the product since they emit flammable or explosive vapor Do not dry items cleaned with industrial chemicals in the dryer Do not dry unwashed items in the dryer Items soiled with cooking oils acetone alcohol fuel oil kerosene stain remover turpentine paraffin and paraffin removers must be washed in hot water with plenty of detergent
8. should not be placed in a dryer Damage to the dryer can result if metal reinforcements come loose during drying e Check all garments for forgotten lighters coins metal pieces needles etc before loading e At times when your dryer is not in use or after the laundry is taken out following the completion of drying process turn off by using the On Off button In cases when the On Off button is on while the dryer is energized keep the door of the dryer closed Intended use e This product has been designed for domestic use It should not be used for other purposes e Use the product only for drying laundry that are marked accordingly e Dry only those articles in your product that are stated in this manual e This product is not intended to be used by persons with physical sensory or mental disorders or unlearned or inexperienced people including children unless they are attended by a person who will be responsible for their safety or who will instruct them accordingly for use of the product Children s safety Electrical appliances are dangerous for the children Keep children away from the machine when it is operating Do not let them tamper with the machine e Packaging materials are dangerous to children Keep the packaging materials out of reach of children or dispose them by classifying according to waste directives e Do not allow children sit climb on or enter in the product e Children should be sup
9. BEKO Vented Time Dryer DRVT 71 W oO 9et the best from Y Read this manual prior to initial operation of the product Dear Customer We hope that your product which has been manufactured in modern facilities and passed through a strict quality control procedure will give you very good results We advise you to read through this manual carefully before using your product and keep it for future reference This User Manual will e Help you use your machine in a fast and safe way e Read the User Manual before installing and starting your product e In particular follow the instructions related to safety e Keep this User Manual within easy reach for future reference e Please read all additional documents supplied with your product Remember that this User Manual is also applicable for several other models Explanation of symbols Throughout this User Manual the following symbols are used Important safety information Warning for hazardous situations with regard to life and property Caution Warning for supply voltage Caution Warning for fire hazard Caution Warning for hot surfaces Read the instructions E B o pee D Useful information Important information or useful hints about usage This appliance s packaging material is recyclable Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose Your appliance also contains a great amount of recyc
10. Cancel status in order to change the programme Change the programme and press Start Pause Cancel button to start it After the programme is finished The O Anti creasing and Filter cleaning warning LEDs on the programme follow up indicator will light up when the programme comes to an end The door can be opened and the machine becomes ready for a second cycle 1 Press the On OfP button to shut down the machine 2 Take out the laundry from the machine 3 Check if there are any foreign objects in the machine 4 Clean the filter after drying 18 EN 8 Maintenance and cleaning Fluff filter Lint and fibres released from the laundry to the air during the drying cycle are collected in the Fluff Filter GH Such fibre and lint are generally formed during wearing and washing G Always clean the filter after each Drying process You can clean the filter and filter area by vacuum cleaner For Filter cleaning 1 Open the cover 2 Remove the fluff filter by pulling it up and open the filter 3 Clean lint fibre and the fluff by hand or with a soft piece of cloth 4 Close the filter and place it back into its seat MH Clogging may arise on the filter surface after using your machine for some time if this occurs wash the filter with water and dry it before using again E lt is recommended that the accumulated fluff in the vent hose be
11. Label affixed to the appliance Model No Serial No Retailer Date of purchase Republic of Ireland All Refrigeration 01 862 3411 All Cookers Washing Machines amp Dryers Tumble Dryers Dishwashers Before requesting service please check the trouble shooting guide in the Operating Instructions as a charge may be levied where no fault is found even though your product may still be under guarantee Service once the manufacturers guarantee has expired If you have purchased an extended guarantee please refer to the instructions contained within the extended guarantee agreement document Otherwise please call the appropriate number above where service can be obtained at a charge Should you experience any difficulty in obtaining service please contact the Customer Help Line Tel 0845 600 4911 For service under guarantee simply telephone the appropriate number below UK Mainland amp Northern Ireland Fridges amp Freezers 0845 600 4903 Electric Cookers 0845 600 4902 Gas amp 0845 600 4905 Dual Fuel Cookers Washing Machines amp Dryers Tumble Dryers 0845 600 4906 23 EN BEKO Beko plc Beko House Caxton Way Watford Hertfordshire WD18 8UF Tel 0845 6004911 Fax 0845 6004922 Email service beko co uk www beko co uk
12. are schematic and may not match your product exactly Values stated on the machine labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant standards Depending on operational and environmental conditions of the appliance values may vary 5 EN a Important safety instructions This section includes safety information that will help protection from risks of personal injuries or materialistic damages Failure to follow these instructions shall cause any warranty and reliability commitment to become void General safety Never place the machine on a carpet covered floor otherwise lack of airflow beneath the machine may cause electrical parts to overheat This will cause problems with your machine e If the power cable or mains plug is damaged you must call Authorised Service Agent for repair e The product should not be plugged in during installation maintenance and repair works Such works should always be made by the technical service Manufacturer shall not be held responsible for damages arising from processes carried out by unauthorised persons e Connect the product to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table e Operate your product at temperatures between 5 C and 35 C e Do not use electrical devices in the product e Do not connect the air exit of the product to the chimney holes which are used
13. contents insurance policy or may be available separately from your retailer Important notes e Your product is designed and built for domestic household use only e The guarantee will be void if the product is installed or used in commercial or non residential domestic household premises e The product must be correctly installed located and operated in accordance with the instructions contained in the User Instructions Booklet provided e Professional installation by a qualified Electrical Domestic Appliance Installer is recommended for all Washing Machines Tumble Dryers Dishwashers Dryers and Electric Cookers e Gas Cookers must only be installed by a CORGI or BORD GAIS registered Gas Installer e The guarantee is given only within the boundaries of the United Kingdom and the Republic of Ireland e The guarantee is applicable only to new products and is not transferable if the product is resold e disclaims any liability for incidental or consequential damages e The guarantee does not in anyway diminish your statutory or legal rights 22 EN 12 Service Please keep your purchase receipt or other proof of purchase in a safe place you will need to have it should the product require attention under guarantee You should also complete the details below it will help us assist you when requesting service The model number is printed on the Instruction Booklet and the serial number is printed on the Rating
14. d another programme mode is selected while the machine is operating You must cancel the ongoing programme in order to change the drying programme See Ending the program through canceling Adding removing laundry in standby mode In order to add or take out laundry after w start up of the programme Press the Start Pause Cancel button to switch the machine to Pause mode Drying process will stop 2 Open the door at Pause position and close it again after adding or taking out laundry 3 Press Start Pause Cancel button to start the programme Any laundry added after the drying process was started may cause the already dried clothes in the machine intermingle with wet cloth es and the result will be wet laundry after the drying process is over Laundry may be added or taken out as much as desired during a drying process but as this process will interrupt drying continuously it will extend the programme duration and increase energy consumption Therefore it is recommended to add laundry before the drying programme is started Child proof lock There is a childproof lock to prevent any programme interruption due to the pressing of keys while the program is on The loading door and all keys except the On Off key on the panel are deactivated when the child proof lock is active In order to activate the childproof lock press the Start Pause Cancel and Low temperature button
15. ed service agent make sure that its location and power supply installations are appropriate If they are not call a qualified electrician to have any necessary arrangements carried out e Make sure that the power connections of the product are in accordance with the instructions given in relevant chapters of this manual Disposing of packaging material Packaging materials are dangerous to children Keep packaging materials in a safe place out of reach of children Packaging materials of your product are manufactured from recyclable materials Sort and dispose of them in accordance with recycled waste instructions Do not dispose of them with normal domestic waste Transportation of the machine 1 Unplug the machine from the mains 2 Remove the water drain if any and chimney connections 3 Drain water remained in the machine completely before transportation Disposing of the old machine Dispose of your old machine in an environmentally friendly manner Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your machine Before disposing of your old machine cut off the power cable plug and make the loading door lock unusable to avoid dangerous conditions to children 9 EN 4 Electrical Connection Make sure that you have an earthed power outlet socket rated at 13 amps minimum Attention If you use your dryer as built in the socket must be reachable after ins
16. ervised to ensure that they do not play with the product e Close the loading door when you leave the area where the product is located 7 EN E Installation Refer to the nearest Authorised Service Agent for installation of your product Preparation of location and electrical installation for the product is under customer s responsibility Installation and electrical connections must be carried out by a gualified personnel Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products will cause risks for your safety Appropriate installation location e Install the product in an environment which has no risk of freezing and is in a stable and level position e Operate your product in a well ventilated dust free environment e Do not block the air ducts in front of and under the product with materials such as long pile rugs and cupboard plinths e Do not place your product on a long pile rug or on similar surfaces e Do not install the product behind a door with a lock sliding door or a hinged door which can strike the product e Once the product is installed it should stay at the same place where its connections have been made When installing the product make sure that the rear wall of it does not touch anywhere tap socket etc and also pay attention to install the product at a place where it will stay permanently Do not place the product on
17. for the hinges and one for the door lock on the opposite side 7 Insert the door lock system on the opposite side of the hinge and be sure it is properly fitted 8 Reverse the door Fit the door on the opposite side using 4 screws removed Fix the contact pin into the top side of the door by turning 90 in the clockwise direction amp 3 5 2 6 3 21 EN 41 Guarantee Your new product is guaranteed against the cost of breakdown repairs for twelve months from the date of the original purchase What is covered e Repairs necessary as a result of faulty materials defective components or manufacturing defect e The cost of functional replacement parts but excluding consumable items e The labour costs of a approved repairer to carry out the repair What is not covered e Transit delivery or accidental damage or misuse and abuse e Cabinet or appearance parts including knobs flaps handles or container lids e Accessories or consumable items including but not limited to ice trays scrapers cutlery baskets filters and light bulbs e Repairs required as a result of unauthorised repair or inexpert installation that fails to meet the requirements contained in the user instruction book e Repairs to products used on commercial or non residential household premises e Loss of frozen food in freezers or fridge freezers Food loss insurance is often included within your household
18. ine allows for the laundry type e Laundry may be tangled after washing Separate your laundry before placing them into your dryer e Sort your laundry according to their types and thicknesses Dry the same type of laundry together E g fine kitchen towels and table cloths dry faster than the thick Dain towels Correct load capacity a A Consider the information in the Programme Selection Table Always start the programme in accordance with the maximum load capacity Adding laundry to the machine more than the level shown in the figure is not recommended Drying performance will degrade when the machine is overloaded Furthermore your dryer and your laundry can be damaged Place your laundry into the drum loosely so that they will not get tangled Large pieces E g bed sheets quilt covers large tablecloths may bunch up Stop the dryer 1 2 times during drying process to separate bunched up laundry Following weights are given as examples Approximate Home articles weights g Cotton quit covers double 1500 Cotton quit covers single 1000 Bed sheets double Bed sheets single Large tablecloths Small tablecloths Tea napkins Bath towels Hand towels 350 Approximate weights g Garments Blouses 150 Cotton shirts 300 Shirts 200 Cotton dresses 500 Dresses Jeans Handkerchiefs 10 pieces T Shirts Loading e Ope
19. lable material It is marked with this label to indicate the used appliances that should not be mixed with other waste This way the appliance recycling organised by your manufacturer will be done under S EE the best possible conditions in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Eguipment Contact your town hall or your retailer for the used appliance collection points closest to your home We thank you doing your part to protect the environment g TABLE OF CONTENTS 1 Your Dryer 4 OVEIVICW Li 4 2 Important safety information6 General Safety 6 Intended use 7 Children s safety 7 3 Installation 8 Appropriate installation location 8 Under counter installation 8 Ventilation hose and connection for products equipped with an outlet Venise ara 8 Adjusting feet a 9 FIPS USC ra 9 Disposing of packaging material 9 Transportation of the machine 9 Disposing of the old machine 9 4 Electrical Connection 10 Electrical reguirements 10 Fitting a different plug 10 5 Initial preparations for drying11 Things to be done for energy SAVINO Banti ia 11 Laundry suitable for drying in the Machine nee iii 11 Laundry unsuitable for drying in the MAChINE WWW 11 Preparing laundry for drying
20. ly cord should be replaced by the manufacturer its service agent or similarly qualified people Built under installation This appliance can be installed under a worktop A Undercounter installation without the top cover must only be carried out by an authorised agent Risk of electric shock A Important Fitting a different plug As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug proceed as follows 1 Connect the green yellow or green earth wire to the terminal in the plug marked E or with the symbol or coloured green and yellow or green 2 Connect the blue neutral wire to the terminal in the plug marked N or coloured black 3 Connect the brown live wire to the terminal in the plug marked L or coloured red With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the main fuse box If in doubt contact a qualified electrician Green and yellow or green Blue or black Brown or red Washer dryer combination Do not stack washing machine on top of the tumble dryer This would damage both appliances and guarantees would become void It is also unsafe to stack an appliance on top of another without using a suitable and approved stacking kit obtained from the manufacturer of the appliances e A special stacking kit is required as an optional extra please contact cust
21. n the loading door e Place laundry items loosely into the dryer e Push the loading door to close Ensure that no items are caught in the door 12 EN selecting a Programme and Operating Your Machine Control panel 1 2 3 4 6 5 1 Filter cleaning warning light 4 On Off button Warning light turns on when the filter is Use to turn on and off the machine full 5 Programme selection knob 2 Programme follow up indicator Use to select a programme Use to follow up the progress of the 6 Start Pause Cancel button current programme Use to start pause or cancel the 3 Low temperature programme Use to dry in low temperatures 13 EN Preparing the machine 1 Plug in your machine 2 Place the laundry in the machine 3 Press the On Off button E Pressing the On Off button does not necessarily mean that the programme has started Press Start Pause Cancel button of the machine to start the programme Main programmes eAnti creasing A 2 hour anti creasing programme to prevent laundry from creasing will be activated if you do not take the laundry out after the programme has come to an end This programme rotates the laundry in 60 second intervals to prevent creasing eFreshen up Only ventilation is performed for 10 minutes without blowing hot air You can air your clothes that have been kept at closed environments for a long time thanks to this programme to deodorize unpleasan
22. nt water accumulation in the hose make sure that it is not folded on the floor 8 EN IL 27 OA Ot Ei val pu TLL A The air ventilation hose should not be connected to the chimney of a stove or a fireplace A Do not operate your machine at the same time with heaters such as a coal or gas stove Airflow may cause the chimney to flare up Airflow may cause the chimney to flame up Adjusting feet In order to ensure that your product operates more silently and vibration free it must stand level and balanced on its feet Front feet of your product can be adjusted Balance the machine by adjusting the feet J N KOEN y ae 1 Loosen the feet by hand 2 Adjust the feet until the product stands level and firmly on the floor GI Do not use any tools to loosen the adjustable feet otherwise they can be damaged GI Never remove the adjustable feet from their housings 2 plastic pieces supplied along with the user manual prevent your machine from slipping on wet and slippery surfaces To install the plastic parts 1 Tilt your product to backwards 2 Fit the plastic parts on to the front adjustable feet Press on the plastic parts to snap them into their seating 8 Check the balance of your product again and readjust the adjustable feet if necessary First use e To have the product ready for operation before calling the authoris
23. omer service 10 EN B Initial preparations for drying Things to be done for energy saving Make sure that you operate the product at its full capacity but pay attention to not exceeding it Spin your laundry at the highest speed possible when washing them Thus the drying time is shortened and energy consumption is decreased Pay attention to dry same types of laundry together Follow the instructions in the user manual for programme selection Make sure that sufficient clearance is provided at the front and rear side of the dryer for air circulation Do not block the grill at the front side of the product Do not open the door of the machine during drying unless necessary If you must certainly open the door pay attention not to keep it open for a long time Do not add new wet laundry during drying Lint and fibres released from the laundry to the air during the drying cycle are collected in the Lint Filter Make sure that you clean the filters before or after each drying In models with condenser make sure that you clean the condenser regularly at least once every month or after every 30 drying cycles In vented models follow the chimney connection rules in the user manual and pay attention to the chimney cleaning Ventilate the room where the dryer is located well during drying For power saving in models with lamps at times when your dryer is not in use keep the door closed if the On Off
24. r temperatures and therefore saves energy Warning LED will light up when you select the function GI You must use this function when you dry your synthetic or delicate laundry Warning indicators G Warning indicators may differ according to the model of your machine Filter cleaning A warning LED will light up to remind filter cleaning after the programme finishes A If the filter cleaning warning LED lights up continuously please refer to Solution suggestions for problems Staring the Programme Press Start Pause Cancel button to start the programme 2 Start Pause Cancel button will light up to indicate that the programme has started Timer follow up indicator One of the LED lights will remain on as far as programme runs and shows the eima remaining time LEDs on the timer follow up indicator will also flash when the child proof lock is activated Changing the programme after the programme has started You can use this feature to dry your laundry in a different programme after your machine has started to run For example Press and hold the Start Pause Cancel button for about 3 seconds to select 80 minutes programme instead of 60 minutes programme Select the 80 minutes programme by rotating the program knob Press Start Pause Cancel button to start the programme The programme which is selected first will go on even if the programme selection button is moved an
25. s simultaneously for 3 seconds To start a new programme after the programme is over or to interrupt the programme the childproof lock should be deactivated To deactivate the childproof lock press the same buttons for 3 sec 9 JA 16 EN E One of the LEDs on the program follow up indicator starts flashing when the child proof lock is activated Child proof lock is deactivated when the machine is restarted by pressing the On Off button Ending the programme through cancelling The program which is selected first will keep on going even if the position of the programme selection button is changed A new programme can be selected and started after Programme cancel is activated in order to change the drying programme G cancel any selected programme Press Start Pause Cancel button for about a duration of 3 seconds The Filter cleaning warning LEDs as well as the O warning LED on the programme follow up indicator will light up at the end of this period for reminding purposes A As the inside of the machine will be excessively hot when you cancel the programme while the machine is running activate the freshen up program to cool it down End of programme The Filter cleaning warning LEDs as well as the O warning LED on the programme follow up indicator will light up at the end of the programme The door can be opened and the machine becomes ready for a second cycle
26. t odors eTimer programmes You can select one of the 10 min 60 min 80 min timer programmes to achieve the final drying level Dry the cotton laundry at high temperatures and synthetic and easy care laundry at low temperatures depending on the type of the laundry GI You must press the Low temperature button for synthetics AN The drum door and load may be very hot 14 EN Programme selection and consumption table Program table Approximate Spin speed in washing amount of Drying time P ity ki AS bali Sapaciko machine rpm remaining minutes humidity Cottons Coloreds 1000 bee Ready to Wear 1000 80 100 100 130 2 1000 700 130 Ready to Iron 1000 60 80 so Tr v so 40 eo xo oa Ready to Wear 800 40 30 60 sco 50 3000 Delicates DI 9 Energy consumption values Approximate A Energy Spin speed in washing amount of Programs Capacity kg medine ar BR consumption ao value kWh For fabrics spun at higher spin speeds than shown in the table the drying times will be reduced Energy Label standard programme EN 61121 2005 All values given in the table have been fixed according to EN 61121 2005 Standard These values may deviate from the table according to the laundry type laundry spin speed environmental conditions and voltage fluctuations 15 EN Auxiliary function Low temperature This function allows for drying at lowe
27. tallation or a separate switch which can disconnect the two poles must be used in the installation Check for suitability For a permanent connection a master switch with at least 3mm contact Clearance and minumum 13 A rating must be used Electrical requirements Before you insert the plug into the wall socket make sure that the voltage and the frequency shown in the rating label corresponds to your electricity supply We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position Should the mains lead of the appliance become damaged or need replacing at any time it must be replaced by a special purpose made mains lead which can only be obtained from a Authorised Service Agent A Warning This appliance must be earthed If the fitted moulded plug is not suitable for your socket then the plug should be cut off and an appropriate plug fitted The moulded plug on this appliance incorporates a 13A fuse Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used Do not forget to refit the fuse cover In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been fitted Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug Fuse covers are available from any good electrical store In order to avoid hazards damaged supp
28. top of the power cable e Keep at least 1 5 cm distance to walls of other furniture Under Counter Installation e Leave at least 3 cm of space between the side and rear walls of the machine and the walls of the counter cupboard when installing your machine under a counter or in a cupboard Never use the tumble dryer without top plate Ventilation hose and connection for products equipped with an outlet vent Ventilation hose assures exhausting of the air from inside the machine Vented dryer has 1 air outlet Stainless sheet metal or aluminum pipes can be used instead of the hose The diameter of the pipe to be used should be minimum 10 cm Maximum hose and pipe lengths are given in the table below Maximum length 1 elbow 45 1 elbow 90 1 elbow 90 short 1 wall Pen ac uu be subtracted from the above maximum length To connect a ventilation hose 1 Connect the air outlet hose to the hose spacer piece by turning it anti clockwise 2 Make the hose passages as shown below Exhaust of humid air from the dryer into the room is inconvenient It may damage the walls and furniture in the room The ventilation hose can be routed outdoors via a window or it can be connected to an air outlet in the wall see diagram below Air outlet hose must be extended directly to the outdoors There must be a small number of elbows as not to hinder air ventilation G To preve
29. use electric shock If you have any suspect about the grounding connection have it checked by a qualified electrician service representative or service personnel Do not reach into the machine when the drum is spinning Unplug the machine when it is not in use Never wash down the appliance with water There is the risk of electric shock Always disconnect by unplugging from the mains before cleaning Never touch the plug with wet hands Never unplug by pulling on the cable always pull out by grabbing the plug only Do not operate the machine if the power cable or plug is damaged Never attempt to repair the machine yourself otherwise you will be putting your life and others lives in danger For malfunctions that cannot be solved by following the information given in the safety instructions Turn off the machine and contact an authorised service agent Do not stop the dryer before the drying cycle comes to an end unless you will remove all laundry from the dryer fast in order to lay them and dissipate the heat Remove the door of the drying compartment before decommissioning or disposing of the product The final step of the drying cycle cool down cycle occurs without applying heat to ensure that the items are left at a temperature that will not damage them e Fabric softeners or similar products should be used as specified by the fabric softener instructions e Underwear that contains metal reinforcements
30. y having a label stating that they are emit flammable or explosive vapor suitable for drying in a dryer and make e Do not dry items cleaned with Laundry suitable for drying in the machine Always follow the suggestions on the 11 EN industrial chemicals in the dryer e Do not dry your unwashed laundry in the dryer e Items soiled with cooking oils acetone alcohol fuel oil kerosene stain remover turpentine paraffin and paraffin removers must be washed in hot water with plenty of detergent before being dried in the dryer e Garments or pillows bolstered with rubber foam latex foam shower bonnets water resistant textiles materials with rubber reinforcement and rubber foam pads should not be dried in the dryer Do not use fabric softeners and anti static products unless they are recommended by the manufacturers of the fabric softener or the product e Do not dry the underwear reinforced with metal parts in the dryer If these metal reinforcements loosen and break De drying they will damage your Preparing laundry for drying e Check all laundry items before loading them into the product to make sure that there are no lighters coins metal items needles and etc in their pockets or on any part of them e Fabric softeners and similar products must be used in accordance with the instructions of the manufacturer of the relevant products e All laundry must be spun at the highest spin speed that your washing mach
Download Pdf Manuals
Related Search