Bosch WTY86790GB tumble dryer
Contents
1. Moisture sensor 1 The dryer is equipped with stainless steel moisture sensors Moisture sensors measure how damp the laundry is A thin layer of limescale may build up on the moisture sensors after prolonged use This must be removed regularly Open the door and clean the moisture sensors with a damp sponge that has a rough surface 1 A Do not use steel wool or abrasive materials Cover for steam nozzle in the drum depending on the model After prolonged operation limescale and fluff may accumulate on the cover of the steam nozzle Clean regularly 1 Open the door and remove the cover with a screwdriver Clean the cover under running water 2 Push and click the cover back in place Clean the filter in the refresher tank if it is dirty depending on the model Regularly clean the filter under running water This prevents stubborn deposits dirt from building up 1 Remove the condensation container 2 Remove the filter and clean it under running water 3 Re insert the filter and push in the condensation container until it locks into place Care and cleaning Heat exchanger c The dryer s heat exchanger is automatically cleaned during drying and Heat exchanger is being rinsed is displayed in the display panel Do not pull out the condensation container during this cleaning process Filter in the condensation container The filter is cleaned automatically when the condensation conta2. 1 E Care and cleaning 2 3 After sales ServiCeO 4 Optional accessorlesS 4 Technical data 4 Reversing the door 5 7 Read these instructions before operating the dryer You must also observe the separate instruction manual Keep all the documents in a safe place for future reference or to pass on to the next owner en Environmentally responsible disposal Care and cleaning Dispose of packaging In an environmentally responsible manner This appliance is labelled in accordance with European Directive 2012 19 EU concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Installation Scope of delivery dryer instruction manual installation and maintenance instructions jug and woollens basket depending on the model Check dryer for transport damage The dryer is very heavy Do not attempt to lift it on your own Be careful to avoid sharp edges Do not set up in a room that is susceptible to frost Freezing water may cause damage If in doubt have the appliance connected by a specialist Do not lift the dryer by protruding parts e g the door risk of breakage Setting up the dryer Ensure that the appliance is ins
3. push in the condensation container until it locks into place Care and cleaning Heat exchanger ee The dryer s heat exchanger is automatically cleaned during drying and Heat exchanger is being rinsed is displayed in the display panel Do not pull out the condensation container during this cleaning process Filter in the condensation container A The filter is cleaned automatically when the condensation container is emptied However the filter should still be cleaned regularly under running water This prevents stubborn deposits dirt from building up lf the condensation drain is installed depending on the model it is not necessary to clean the filter separate Instructions for the condensation drain 1 Pull out the condensation container 2 Pull the filter out of its snap in lock 3 Clean the filter under running water or in the dishwasher 4 Refit the filter 5 Push the condensation container back in until it locks into place IN Only operate the dryer with the filter inserted After sales service If you cannot rectify the fault yourself instruction manual What to do if page 12 please contact our after sales service We will always find an appropriate solution and avoid unnecessary visits by engineers You can find the contact details for your nearest after sales service on page 12 of the instruction manual or in the after sales service directory Please give the after sa
4. the dryer for two hours The dryer contains residual water This can flow out if the dryer is tilted The refresher tank must not contain any distilled water If necessary run the Steam Refresh programme Dryer housing control panel Remove detergent residues immediately Wipe with a soft damp cloth Do not clean with a water jet During drying water may accumulate between the window and the seal Moisture sensor 1 The dryer is equipped with stainless steel moisture sensors Moisture sensors measure how damp the laundry is A thin layer of limescale may build up on the moisture sensors after prolonged use This must be removed regularly Open the door and clean the moisture sensors with a damp sponge that has a rough surface Cover for steam nozzle in the drum depending on the model After prolonged operation limescale and fluff may accumulate on the cover of the steam nozzle Clean regularly 1 A Do not use steel wool or abrasive materials 1 Open the door and remove the cover with a screwdriver Clean the cover under running water 2 Push and click the cover back in place Clean the filter in the refresher tank if it is dirty depending on the model Regularly clean the filter under running water This prevents stubborn deposits dirt from building up 1 Remove the condensation container 2 Remove the filter and clean it under running water 3 Re insert the filter and
5. Environmentally responsible disposal Dispose of packaging in an environmentally responsible manner This appliance is labelled in accordance with European Directive 2012 19 EU concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Installation h Scope of delivery dryer instruction manual installation and maintenance instructions jug and woollens basket depending on the model Check dryer for transport damage The dryer is very heavy Do not attempt to lift it on your own Be careful to avoid sharp edges Do not set up in a room that is susceptible to frost Freezing water may cause damage If in doubt have the appliance connected by a specialist Do not lift the dryer by protruding parts e g the door risk of breakage Setting up the dryer Ensure that the appliance is installed on a clean level and firm surface The appliance plug must always be accessible Do not obstruct the air inlet on the dryer Keep the area around the dryer clean Level the dryer using the threaded feet and a spirit level Do not remove the threaded feet under any circumstances N Do not set up the dryer behind a door or sliding door as this may obstruct the dryer door or prevent it from opening This will prevent c
6. hildren from locking themselves in thereby putting their lives at risk Take all accessory parts out of the drum The drum must be empty Clean and level Make sure that the air For mains connection see Safety instructions page 13 o Connect to an AC earthed socket If in doubt have the socket checked by a specialist The connected load and necessary fuse protection are specified on the rating plate Frost protection Transport Preparation 1 Empty the condensation container Page 4 2 Select any programme using the programme selector 6 Transport the dryer in a vertical upright position 7 Following transportation do not use the dryer for two hours 4 Wait 5 minutes and then empty the condensation container again N Switch the dryer off using the programme selector 9 The dryer contains residual water This can flow out if the dryer is tilted The refresher tank must not contain any distilled water If necessary run the Steam Refresh programme inlet remains unobstructed The mains voltage and the voltage shown on the rating plate page 4 must be the same 3 Press the Dll Start Pause button condensation water is pumped into the container Care and cleaning Dryer housing control panel Remove detergent residues immediately Wipe with a soft damp cloth Do not clean with a water jet During drying water may accumulate between the window and the seal
7. hnicians using original spare parts Optional accessories Washer dryer stack connection set WTZ ono DA dryer can be placed on top of a suitable washing machine with the same width and depth to save space The dryer must be fastened to the washing machine using this connection set WTZ 11400 with pull out worktop 7A Wollens basket AVVO For drying individual wollen fabrics sports shoes and soft toys see separate instructions for Woollens basket Trage Platform For easier loading and unloading The basket contained in the drawer can be used to carry the laundry Technical data Dimensions DxWxH 60 x 60 x 85 cm adjustable height Weight approx 57 kg Max capacity 8 kg 9 kg Condensation container 4 6 Refresher tank approx 0 4 Connection voltage 220 240 V Connected load max 1000 W for models with a max 1600 W steam function Fuse protection 10A Ambient temperature S oo E Product number Production number Inside of door The rating plate can be found on the back of the dryer depending on the model operating instructions Programme overview page 7 N Dryer o BEE Installation and maintenance instructions Contents Page E Environmentally friendly disposal 1 InstallatiON 1 Frost protection Transport
8. iner is emptied However the filter should still be cleaned regularly under running water This prevents stubborn deposits dirt from building up lf the condensation drain is installed depending on the model it is not necessary to clean the filter separate Instructions for the condensation drain 1 Pull out the condensation container 2 Pull the filter out of its snap in lock 3 Clean the filter under running water or in the dishwasher 4 Refit the filter 5 Push the condensation container back in until it locks into place A Only operate the dryer with the filter inserted After sales service If you cannot rectify the fault yourself instruction manual What to do if page 12 please contact our after sales service We will always find an appropriate solution and avoid unnecessary visits by engineers You can find the contact details for your nearest after sales service on page 12 of the instruction manual or in the after sales service directory Please give the after sales service the product number E no and the production number FD of the appliance Product number Production number You can find this information inside the door in the opened service flap and on the rear of the appliance depending on the model Trust the expertise of the manufacturer Contact us for assistance In this way you can rest assured that the repair will be carried out by trained service tec
9. les service the product number E no and the production number FD of the appliance Product number Production number You can find this information inside the door in the opened service flap and on the rear of the appliance depending on the model Trust the expertise of the manufacturer Contact us for assistance In this way you can rest assured that the repair will be carried out by trained service technicians using original spare parts Optional accessories Washer dryer stack connection set WTZ oro pi dryer can be placed on top of a suitable washing machine with the same width and depth to save space The dryer must be fastened to the washing machine using this connection set WTZ 11400 with pull out worktop 7A Wollens basket AVIV For drying individual wollen fabrics sports shoes and soft toys see separate instructions for Woollens basket MIA Platform AVIS For easier loading and unloading The basket contained in the drawer can be used to carry the laundry Technical data Dimensions DxWxH 60 x 60 x 85 cm adjustable height Weight approx 57 kg Max capacity 8 kg 9 kg Condensation container 4 6 Refresher tank approx 047 Connection voltage 220 240 V Connected load max 1000 W for models with a max 1600 W steam function Fuse protection 10A Ambient temperature 3 35 C Product number Production number The rating plate can be found on the back of the dryer de
10. pending on the model operating instructions Programme overview page 7 Inside of door 406 90006956 OU 0 OON Dryer Installation and maintenance instructions Contents Page E Environmentally friendly disposal 1 M Installation cio is ica a o has 1 Frost protection Transport 1 Care and cleaning 2 3 After sales ServiCO 4 Optional accessorlesS 4 Technical data 4 Reversing the door 5 7 Read these instructions before operating the dryer You must also observe the separate instruction manual Keep all the documents in a safe place for future reference or to pass on to the next owner en
11. talled on a clean level and firm surface The appliance plug must always be accessible Do not obstruct the air inlet on the dryer Keep the area around the dryer clean Level the dryer using the threaded feet and a spirit level Do not remove the threaded feet under any circumstances Do not set up the dryer behind a door or sliding door as this may obstruct the dryer door or prevent it from opening This will prevent children from locking themselves in thereby putting their lives at risk Take all accessory parts out of the drum The drum must be empty Clean and level Make sure that the air inlet remains unobstructed For mains connection see Safety instructions page 13 Connect to an AC earthed socket If in doubt have the socket checked by a specialist The mains voltage and the voltage shown on the rating plate page 4 must be the same The connected load and necessary fuse protection are specified on the rating plate Frost protection Transport Preparation 1 Empty the condensation container Page 4 2 select any programme using the programme selector 3 Press the Dll Start Pause button condensation water is pumped into the container 4 Wait 5 minutes and then empty the condensation container again 5 Switch the dryer off using the programme selector N 6 Transport the dryer in a vertical upright position 7 Following transportation do not use
Download Pdf Manuals
Related Search