Dimplex DXLWP400 space heater
Contents
1. frame and hollow concrete SEEK SPECIALIST ADVICE 1 Select the position for the heater ensuring there is clearance from any furniture and fittings of at least 150mm above the heater 50mm below and 25mm each side Curtains must not be closer than 150mm from the top of theheater 2 Position the drilling template provided on the wall ensuring it is level Mark the position of the relevant holes on the wall at the edge of template Before drilling check that the distance between the hole centres is correct 340mm for 400W Models and 540mm for 800W models see Fig 2 4 150mm 130mm 340mm 400W 130mm j mre 540mm 800W 7 Drilling Holes Fig 2 3 Drill the wall at the three marked positions and fit the wall plugs Ensure template has been removed 4 Fix two No 8 screws to the top two holes leaving 3mm of the screw exposed Hang the heater on the screws 5 Fit the bottom bracket found in the fixing kit in the slot at the base of the heater and screw the bracket to the wall Test that the heater is now securely fixed to the wall Operation IMPORTANT OBJECTS OR CLOTHING MUST NOT BE PLACED ON THIS HEATER Before using the heater ensure that all warnings and instructions have been read carefully OPERATION SINGLE RATED MODELS Models DXLWP400 DXLWP400T1I DXLWP800 and DXLWP800TI N Turn the heater on using the switch on the right side of the heater the switch will be illuminated O2. the timer clock will stop until power is restored reset the time of day to ensure correct ON and OFF times Cleaning WARNING ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE CLEANING THE HEATER Do not use detergents abrasive cleaning powder or polish of any kind on the body of the heater Allow the heater to cool then wipe with a dry cloth to remove dust and a damp cloth not wet to clean off stains Be careful not to allow moisture into the heater Recycling For electrical products sold within the European Community At the end of the electrical products useful life it should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or retailer for recycling advice in your country After Sales Service Your product is guaranteed for three years from the date of purchase Within this period we undertake to repair or exchange this product free of charge subject to availability provided it has been installed and operated in accordance with these instructions Your rights under this guarantee are additional to your statutory rights which in turn are not affected by this guarantee Should you require after sales service you should contact our customer services help desk on 0845 600 5111 It would assist us if you can quote the model number series date of purchase and nature of the fault at the time of your call The customer services help desk will also be able to a
3. when using this heater in series with a thermal control a program controller a timer or any other device that switches on the heat automatically since a fire risk exists when the heater is accidentally covered or displaced If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard WARNING Servicing and product repairs should only be undertaken by the manufacturers approved service agent or a similarly qualified person using only exact manufacturer approved spare parts Electrical Connection WARNING THIS APPLIANCE MUST BE EARTHED If the socket outlets in your home are not of the 13 amp BS1363 type they will not accept the plug connected to this heater therefore cut off the plug When cut off this plug can constitute a shock hazard if inserted into a socket outlet It must therefore be disposed of safely Before wiring the appropriate plug please note that the wires in this mains lead are coloured in accordance with the following code GREEN YELLOW EARTH BLUE NEUTRAL BROWN LIVE Connect the Green Yellow wire to the terminal marked E or the earth symbol or coloured Green or Green Yellow Connect the Brown wire to the terminal marked L or coloured Red Connect the Blue wire to the terminal marked N or coloured Black DO NOT connect the Brown Live or the Blue Neutral wires to the Earth terminal of your 13 amp plug If the termina
4. PERATION DUAL RATED MODEL Model ARLWPS800TI The two switches on the side of the heater control the heat output Both switches illuminated indicates maximum output Top switch only illuminated indicates 500W output on 800W model Bottom switch only illuminated indicates 300W output on 800W model Note on models fitted with a timer at least one switch must be illuminated for the heater to operate MODELS WITH TIMER see Fig 3 DXLWP400TI and DXLWPS8O00TI N 1 Switch The switch on the side of the heater turns the heater on Note This switch must be in the on position before the heater will operate ARLWP800TI 2 Switches The two switches on the side of the heater control the amount of heat available as described above Operation Dual Rated Model NOTE At least one switch must be in the On position before the heater will operate Models with Timer DXLWP400TI DXLWP800TI N amp ARLWP8OOTI Set the I O slide switch on the timer Fig 3 to Position O Heating Off Position Manual operation This setting allows power to the heater uninterrupted by the timer settings The heat selector switch will control the output see Using the heater Fig 3 Position Auto operation DO NOT disconnect this heater from the mains supply unless it is being taken out of use e g in summer or for storage otherwise the timer clock will stop n Setting the time o
5. dvise you should you need to purchase any spares Please do not return a faulty product to us in the first instance as this may result in loss or damage and delay in providing you with a satisfactory service Please retain your receipt as proof of purchase This product complies with the European Safety Standards EN60335 2 30 and the European Standard Electromagnetic Compatibility EMC EN55014 EN60555 2 and EN60555 3 These cover the essential requirements of EEC Directives 2006 95 EC and 2004 108 EC X Dimplex A world of expertise Millbrook House Grange Drive Southampton Customer Helpline 0844 879 3588 Fax 0844 879 3583 Email aftersales dimplex co uk Website www dimplex co uk Republic of Ireland 01 842 8222 GDC Group LTD All rights reserved Material contained in this publication may not be reproduced in whole or in part without prior permission in writing A division of the GDC Group LTD Millbrook house Grange Drive Hedge End Southampton SO30 2DF
6. f day To set the time of day rotate the timer dial clockwise indicated by the arrow until the correct time of day is opposite the Fig 4 reference mark P see Fig 4 The 24 hour clock is used e g time shown for 3 pm is 15 15 00hrs Setting the Auto ON and OFF times To set the timer 1 Using your finger tip or the tip of a pencil push in as many segments as necessary around the dial according to the times you don t require heat see Fig 4 Each segment pushed in switches the heater OFF for that part of the hour All other segments will be ON For example Fig 5 shows the timer set to et switch the heater ON between 7 am and 7 00am 9 00am 9am and between 4 pm and 9 30 pm Fig 5 2 You can select as many ON periods as you like within the 24 hour day The settings will repeat every day until changed 3 To change ON and OFF times simply push in any ON segments you wish to cancel and pull out new ON segments as required 4 00 pm 9 30 pm Switching to auto Set the heat selector and thermostat for the heat output required Check that the clock shows the correct time of day Set the I Oslide switch to see Fig 4 the convector will switch ON and OFF according to the timer settings see Fig 5 IMPORTANT NOTES Remember to observe all safety warnings when operating the heater on auto setting unattended or attended If the mains supply to the heater is interrupted
7. instance by curtains or furniture as this could cause overheating and a fire risk NEVER cover or obstruct in any way the heat outlet slots at the top of the heater or the air inlet slots in the base of the heater The heater carries the Warning symbol indicating that it must not be covered CAUTION Some parts of this product can become very hot and cause burns Particular attention has to be given where children and vulnerable people are present This appliance can be used by children aged from 8 years and above and by persons with reduced physical sensory or mentalcapabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Children of less than 3 years should be kept away unless continuously supervised Children aged from 3 years and less than 8 years shall only switch on off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children aged from 3 years and less than 8 years shall not plug in regulate and clean the appliance or perform user maintenance Note that due care and consideration must be taken
8. ls of the plug are unmarked or you are in any doubt consult a qualified electrician CAUTION If you use this heater in conjunction with a thermal control programme controller timer or any other device which switches the heater on automatically observe all safety warnings at all times Positioning the Heater Select the position for the heater ensuring there is clearance from any furniture and fittings of at least 150mm above the heater 50mm below wall mounted and 25mm each side Curtains must not be closer than 150mm from the top of the heater Free Standing Operation see Fig 1 NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET FITTED FEET ARE PACKED SEPARATELY IN CARTON 1 Lay the heater on its front 2 Remove the two star head screws from the base of the heater using a x head screwdriver 3 Place feet over base of heater align holes and engage hook on foot into the recess on the back of the heater see Fig 1 4 Replace the screws but do not overtighten poaa T TT aa L Fig 1 Rear View Installation The Fixing Kit should contain 1 Drilling Template 3 Screws 3 Rawlplugs and 1 Mounting Bracket Wall Mounted Operation see Fig 2 Suggested Fixings SOLID BRICK BLOCK No 8 Rawlplug inserts 6mm drill bit PLASTERBOARD If possible locate studding and use No 8 woodscrews directly into the wood otherwise M5 rawlplug intersets are suitable NOTE FOR OTHER WALL TYPES e g Timber
9. xX lt Dimplex Dimplex Low Wattage Panel Heaters BE AB pprove Installation and Operating Instructions INDUKLWPRG Issue 9 Models DXLWP400 DXLWP4O0TI DXLWP800 DXLWP800TI N amp ARLWP8O00TI Dimensions millimetres 600 mm 400W m 800 mm 800W Models Specification SS DXLWP400 400W Neon Heat Switch O DXLWP4O00TI 400W Neon Heat Switch 24 Hour Timer DXLWP800 800W Neon Heat Switch DXLWP800TI N 800W Neon Heat Switch 24 Hour Timer ous ARLWP800TI 800W 2Neon Heat Switches 24 Hour Timer J THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Important Safety Advice When using electrical appliances basic precautions should always be followed to reduce the risk of fire electrical shock and injury to persons including the following IMPORTANT The wall bracket supplied with the appliance must be used WARNING DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF A BATH A SHOWER OR A SWIMMING POOL IMPORTANT If the heater is installed in a room containing a bath or shower it must be so installed that switches and other controls cannot be touched by a person using a bath or shower Do not use outdoors Do not locate the heater immediately below a fixed socket outlet or connection box WARNING In order to avoid overheating do not cover the heater Do not place material or garments on the heater or obstruct the air circulation around the heater for
Download Pdf Manuals
Related Search