De Dietrich DVY1310J dishwasher
Contents
1. Figure O Level AANA pi M Front Ey Illustration of feet adjustment toBack N NOTE dl e The maximum adjustment f ce height of the feet is 60 mm u y Check level side to side About Electricity Connecting For personal safety E DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE E DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE EARTHING CONNECTION FROM THE POWER CORD A WARNING Electrical Requirements Please lookat the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply Use the required fuse 10 amp time delay fuse or circuit breaker recommended and provide separate circuit serving only this appliance Electrical Connection Ensure the voltage and frequency of the power being corresponds to those on the rating plate Only insert the plug into an electrical socket which is earthed properly If the electrical socket to which the appliance must be connected is not appropriate for the plug replace the socket rather than using a adaptors or the like as they could cause overheating and burns A Insure proper ground exists before use GROUNDING INSTRUCTIONS A WARNING This appliance must be earthed In the event ofa malfunction or breakdown earthing will reduce the risk of electric shock by providing a path of least resistance for the electric current This appliance is equi2. Therefore cut off the power supply cable and make the door closing device unusable M Cardboard packaging is manufactured from recycled paper and should be disposed inthe waste paper collection for recycling M Byensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product mM For more detailed information about recycling of this product please contact your local city office and your household waste disposal service DISPOSAL Do not dispose this product as unsorted municipal waste Collection of such waste separately for special treatment is necessary e ENVIRONMENTAL PROTECTION This appliance s packaging material is recyclable Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose Your appliance also contains a great amount of recyclable material It is marked with this label to indicate that in countries that are a members of the European Union the used appliances should not be mixed with other waste This way the appliance recycling organised by your manufacturer will be done under the best possible conditions in compliance with European Directive 2002 96 EC on Waste Electrical and Electronic Equipment Contact your town hall or your retailer for the used appliance collection points closest to your home We than
3. i i Turning on the Appliance 14 Before Calling for Service Change the Programme 14 At the End of the Wash Cycle 14 To review the section ontroubleshooting Tips will help you to solve Some common problems l by yourself 7 Maintenance and cleanimng 15 PREC TING SY SHOW EE 15 If you cannot solve the problems by yourself Caring for the Dishwasher annen 16 please ask for the help of professional technicians 8 Installation Imsiruchon 17 Please carefully read the installation instruction EE 18 Aesthetic panel s dimensions and installation 18 Tension adjustment of the door spring 20 Connection Of dninhoses nnna 20 NO TE Dishwasher installation stenge 21 EE About Electricity Connecting 22 Water Connection 23 The manufacturer following a policy of constant ee development and updating of the product may 9 Troubleshooting Tupe ee eeeeveeeeeees 24 make modifications without giving prior notice Before calling for eprvicge 24 Crrorcodes 25 Techntealmformaton 26 A WARNING 1 IMPORTANT SAFETY INFORMATION READ ALL OF THE INSTRUCTIONS BEFORE USING GROUNDING INSTRUCTIONS W This appliance must be grounded Inthe event ofa malfunction or breakdown grounding will reduce the risk of anelectric shock by providing a path of least resistance of electric current This appliance is equipped with a cord having an equipment grounding conductor and agrounding plug WE The plug must be plugged into
4. ora Similarly qualified person in order to avoida hazard Mi Remove the door to the washing compartment when removing an old dishwasher from service or discarding it W Please dispose of packing materials properly WE Use the dishwasher only for its intended function M During installation the power supply must not be excessively or dangerously bent or flattened Do not tamper with controls WE The appliance is to be connected to the water mains using new hose Sets and that old hose sets should not be reused E The maximum number of place settings to be washed is 10 E The maximum permissible inlet water pressure Is 1Mpa _ rr TE permissible inlet water pressure is 0 04Mpa READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY SAVE THESE INSTRUCTIONS as their modifications Your appliance is compliant with European Directives as well 2 Disposal Dispose of the dishwasher packaging material correctly All packaging materials can be recycled Plastic parts are marked with the standard international abbreviations m PE for polyethylene e g sheet wrapping material m PS for polystyrene e g padding material m POM polyoxymethylene e g plastic clips m PP polypropylene e g Salt filler m ABS Acrylonitrile Butadiene Styrene e g Control Panel Say A WARNING M Packaging material could be dangerous for children mM For disposing of package and the appliance please go to a recycling centre
5. re ready to wash dishes Fillthe detergent dispenser with detergent The marking indicates the dosing levels as illustrated on the right The place of main wash cycle detergent placed MIN means approximately 20g of detergent 3 The place of pre wash cycle detergent placed approximately 5g of detergent Please observe the manufacturers dosing and storage recommendations as stated on the detergent packaging Close the lid and press until it locks in place If the dishes are heavily soiled place an additional detergent dose inthe pre wash detergent chamber This detergent will take effect during the pre wash phase NOTE You find information about the amount of detergent for the single programmes on the last page Please aware that according to the level soiling and the specific hardness of water differences are possible Please observe the manufacturer s recommendations on the detergent packaging Detergents There are 3 sorts of detergents 1 With phosphate and with chlorine 2 With phosphate and without chlorine 3 Without phosphate and without chlorine Normally new pulverised detergent is without phosphate Thus the water softener function of phosphate is not given In this case we recommend to fill salt in the salt container even when the hardness of water is only 6 dH If detergents without phosphate are used in the case of hard water often white spots appear on dishes a
6. the dishes and utensils while they are still hot and more susceptible to breakage They will also dry better E Switch Off the Dishwasher The buzzer of the dishwasher moos for 8 seconds only in this case the programme has ended 1 Switch off the dishwasher by pressing the ON OFF button 2 1 urn off the water tap E Open the door carefully Hot dishes are sensitive to knocks The dishes should therefore be allowed to cool down around 15 minutes before removing from the appliance Open the dishwasher s door leave it ajar and wait a few minutes before removing the dishes In this way they will be cooler and the drying will be improved E Unloading the dishwasher It is normal that the dishwasher is wet inside Empty the lower basket first and then the upper one This will avoid water dripping from the upper Basket onto the dishes in the lower one Maintenance and Cleaning Filtering System The filter prevents larger remnants of food or other objects from getting inside the pump The residues may block the filter in this case they must be removed The filter system consists of a coarse filter a flat Main filter And a microfilter Fine filter Food and soil particles trapped in this filter are pulverized by a Special jet on the lower spray arm and washed down the drain Coarse filter SH Larger items such as pieces of bones or glass that could clog the drain are trapped in the coarse filter To remove an item caught in thi
7. this could cause damage to your dishwasher Illustration 2 3 Connect the inlet hose to the cold water supply 4 Connect the drain hose Refer to diagram Figure 6 5 Connect the power cord 6 Affix the condensation strip under the work surface of cabinet Please ensure the condensation Strip is flush with edge of work surface 7 Place the dishwasher into position 8 Level the dishwasher The rear feet can be adjusted from the front of the dishwasher by turning the screws on the left and right hand side of the cabinet Illustration 5A To adjust the front feet use a wrench and turn the front feet until the dishwasher is level Illustration 5B 9 The dishwasher must be secured in place There are two ways to do this A Normal work surface secure to the work surface by using two woodscrews ensuring the dishwasher weight is not being hit by the surface Illustration 6 B Marble or granite work top secure the bracket to the side panel of the dishwasher and secure the dishwasher to the furniture housing Put the rubber cap over the screw Illustration 7 CONE GEAR Figure 7 Zi Dishwasher must be level for proper dish rack operation and wash performance Place level on door and rack track inside the tub as shown to check that the dishwasher is level 2 level the dishwasher by adjusting the four leveling legs individually ZS When level the dishwasher please pay attention not to let the dishwasher tip over
8. Cloudiness on glassware Black or gray marks on dishes Detergent left in dispenser cups The dishes are not drying Unsatis factory drying result ERROR CODES Possible Causes The dishes were not loaded correctly The programme was not powerful enough Not enough detergent was dispensed Items are blocking the path of spray arms The filter combination in the base of wash cabinet is not clean or is not correctly fitted This may cause the spray arm jets to get blocked Combination of soft water and too much detergent Aluminum utensils have rubbed against dishes Dishes block detergent cups Improper loading Too little rinse aid Dishes are removed too soon Wrong program has been selected Use of cutlery with a low quality coating What To Do See notes in Loading the Dishwasher Baskets Select a more intensive programme See Wash Cycle Table Use more detergent or change your detergent Rearrange the items so thatthe spray can rotate freely Clean and or fit the filter combination correctly Clean the spray arm jets See Cleaning the Spray Arms Use less detergent if you have soft water and select a shortest cycle to wash the glassware and to get them clean Use a mild abrasive cleaner to eliminate those marks Re loading the dishes properly Load the dishwasher as suggested in the directions Increase the amount of rinse aid refill the rinse aid dispenser Do
9. De Dietrich Dishwasher Instruction Manual DVY1310J TEUN d M D E j S aR Bh A Fa INSSE g ld wey M CH Read this Manual 1 Safety Intormaton 1 Dear Customer DIV S WIG Sah eyoaceenesceedecnouscenaseasenedeentceneneousciseanenteeee 2 This appliance is intended to be used in household and similar applications suchas staff kitchen areas in shops offices and other 3 Operating Instructions 3 working environments Control Panel 3 farm houses Dishwasher Features 3 by clients in hotels motels and other residential type environments KE bed and breakfast type environments 4 Prior using for the first timMG ccccccceeee eee eees 4 Please carefully read this manual before using the A Water softener subsea eau he aed naan a alas eee aed 4 dishwasher it will help you to use and maintain the H Loading the Salt into the Softener 0 5 dishwasher properly LG Fillthe Rinse Aid Dispnenser eee 5 Keep it to refer to it at a later date D Function of Detergent eae ri Pass it on to any subsequent owner of the appliance This manual contains sections on safety Instructions 5 PER the Dishwasher PE d e WW 9 Operating Instructions Installation Instructions and Attention before or after loading the Dishwasher Troubleshooting Tips etc Ee H Loadmgtheupperbaekert 9 Loading the Lower Basket 10 GUUIEFY EE 11 6 Starting a washing Drogr mme 13 Wash Cycle Table 13
10. an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances WARNING PROPER USE W Do notabuse sit on or stand onthe door or dish rack of the dishwasher WE Do not touch the heating element during or immediately after use This instruction is only applicable to machines with a visual heating element m Do not operate your dishwasher unless all enclosure panels are properly in place Open the door very carefully if the dishwasher is operating there is a risk of water squirting out WE Do not place any heavy objects on or stand on the door when it is open The appliance could tip forward When loading items to be washed 1 Locate sharp items so that they are not likely to damage the door seal 2 Warning Knives and other utensils with Sharp points must be loaded in the basket with their points down or placedina horizontal position E When using your dishwasher you should prevent plastic items from coming into contact with the heating element This instruction is only applicable to machines with a visual heating element mm Check that the detergent comparment is empty after completion of the wash cycle WE Do not wash plastic items unless they are marked dishwasher safe or the equivalent For plastic items not so marked check the manufacturer s recommendations W Use only detergent and rinse additives designed for an automatic dishwasher W Never use soap laundry det
11. and remove the cap from the salt container E Place the end of the funnel supplied into the hole and introduce about 1 5kg of dishwasher salt Full fill the salt container with water It is normal for asmall amount of water to come out of the salt container W After filling the container screw the cap tightly back clockwise Usually the salt warning light will stop being illuminated within 2 6 days after the salt container has been filled with Salt Immediately after filling the salt into the salt container a washing program should be started We suggest to use the Soak or rapid program Otherwise the filter system pump or other important parts of the machine may be damaged by salty water This is out of warranty A NOTE 1 The salt container must only be refilled when the salt warning light in the control panel comes on Depending on how well the salt dissolves the salt warning light may still be on even though the Salt container is filled If there is no salt warning light in the control panel for some Models you can estimate when to fill the salt into the softener by the cycles that the dishwasher has run 2 If there are spills of the salt a soak or a rapid program should be run to remove the excessive Salt C Fill the Rinse Aid Dispenser Rinse Aid Dispenser The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes which can leave spots and streaks Italso improves drying by allo
12. at attaches to a sink spray can burst if itis installed on the same water line as the dishwasher If your sink has one itis recommended thet the hose be disconnected and the hole plugged How to Disconnect the safety supply hose Turn off the water E Release the water pressure by depressing the pressure release button This relieves water pressure and protects you and the room from severe splashing 3 Unscrew The safety supply hose from the faucet COLD WATER CONNECTION Connect the cold water supply hose to a threaded 3 4 inch connector and make sure that it is fastened tightly in place lf the water pipes are new or have not been used for an extended period of time let the water run to make sure that the water is clear and free of impurities If this precaution is not taken there is a risk that the water inlet can get blocked and damage the appliance Start of Dishwasher The following things should be checked before starting the dishwasher The dishwasher is level and fixed properly PA The inlet valve is open There is a leakage at the connections of the conducts The wires are tightly connected Fl The power is switched on fl The inlet and drain hoses are knotted All packing materials and printings should be taken out from the dishwasher A Attention After installation please make sure to keep this manual The content of this manual is very helpful to the users 9 Troubleshooting Tips Before Calling for Servi
13. ce Review the charts on the following pages may save you from calling for service Possible Causes What ToDo Technical problems General problems Noise Problem Dishwasher doesn t Start water not pumped form dishwasher Suds in the tub Stained tub interior White film on inside surface There are rust Stains on cutlery Knocking noise in the wash cabinet Rattling noise in the wash cabinet Knocking noise in the water pipes Fuse blown or the circuit breaker acted Power supply is not turned on Error code E1 Water pressure is low Door of dishwasher not properly closed Kink in drain hose Filter clogged Kitchen sink clogged Improper detergent Spilled rinse aid Detergent with colourant was used Hard water minerals The affected items are not corrosion resistant A programme was not run after dishwasher Salt was added Traces of salt have gotten into the wash cycle The lid of the softer is loose A spray arm is knocking against an item ina basket Items of crockery are loose in the wash cabinet This may be caused by on site installation or the cross section of the piping 24 Replace fuse or reset circuit breaker Remove any other appliances sharing the same circuit with the dishwasher Make sure the dishwasher is turned on and the door is closed securely Make sure the power cord is properly plugged into the wall socket Check that the water
14. cleaners on any part of the dishwasher Protect Against Freezing please take frost protection measures on the dishwasher in winter Every time after washing cycles please operate as follows 1 Cut off the electrical power to the dishwasher 2 urn off the water supply and disconnect the water inlet pipe from the water valve 3 Drain the water from the inlet pipe and water valve Use a pan to catch the water 4 Reconnect the water inlet pipe to the water valve 5 Remove the filter at the bottom of the tub and use a sponge to soak up water in the sump Cleaning the Door To clean the edge around the door you should use only asoft warm damp cloth To avoid penetration of water into the door lock and electrical components do not use a spray cleaner of any kind A WARNING m Never usea spray cleaner to clean the door panel as it may damage the door lock and electrical components Mm Abrasive agents or some paper towels should not be used because of the risk of scratching or leaving spots onthe stainless steel surface How to Keep Your Dishwasher in Shape After Every Wash When not in Use fora Long Time After every wash turn off the water supply to the When you go on holiday itis recommend that you runa appliance and leave the door slightly ajar so that wash cycle with the dishwasher empty and then remove moisture and odours are not trapped inside the plug from the socket turn off the water supply and leave the door of the ap
15. dishes 8 Oval platter 9 Dinner plates 10 Soup plates 11 Silverware basket IN When you adjust the heigh of the upper basket the maximal size of plates in the lower is different When the upper basketis UP itis 290mm When the upper basketis DOWN itis 250mm Cutlery Basket Cutlery should be placed inthe cutlery basket with the handles at the bottom If the rack has side baskets the Spoons should be loaded separately into the appropriate slots especially long utensils should be placed inthe horizontal position at the front of the upper basket as shown in the picture QCD IZ Daa di 1881 2984 1 Forks s 4 d 2 Soup spoons FANS Sry 3 Dessert spoons D2 S79 4 Teaspoons sde 3 4 5 Knives 13 6 Serving spoons 5 9 3 7 Gravy ladles 555 555 8 Serving forks III OI 68 67 Do not let any item extend through the bottom Always load sharp utensils with the sharp point down WC A WARNING For washing in the dishwasher the following cutlery dishes Are not suitable Are of limited suitability Cutlery with wooden horn china or Some types of glasses can become mother of pearl handles dull after a large number of washes Plastic items that are not heat resistant Older cutlery with glued parts that are not Silver and aluminum parts have a temperature resistant tendency to discolour during washing Bonded cutlery items or dishes Pewter or coo
16. ergent or hand washing detergent in your dishwasher Keep these products out of the reach of children When using your dishwasher follow the precautions listed below AWARNING E improper connection ofthe equipment grounding conductor can result in the risk of an electric shock W Check witha qualified electrician or service representative if you are in doubt whether the appliance is properly grounded Do not modify the plug provided with the appliance If it does not fit the outlet Have a proper outlet installed by a qualified electrician WE Keep children away from detergent and rinse aid keep children away from the open door of the dishwasher there could still be some detergent left inside W This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety W Children should be supervised to ensure that they do not play with the appliance WE Dishwasher detergents are strongly alkaline they can be extremely dangerous if swallowed Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open W The door should not be left open since this could increase the risk of tripping W ifthe supply cord is damaged it must be replaced by the manufacturer or its service agent
17. ewash 50 C Wash 55 C Rinse 3 220 155 1 09 Rinse 65 C Drying Prewash Wash 50 Rinse 65 CT Drying Prewash Wash 40 Rinse 3 229 95 0 71 Rinse 60 C Drying Wash 60 C Rinse 0 77 Rinse 50 C SECH Drying Wash 40 Rinse 20g 30 0 5 Rinse 40 299 175 0 84 10 5 The power consumption of off mode is 0 W left on mode is 0 4 W Turning on the Appliance Starting acycle wash 1 Draw out the lower and upper basket Draw out the lower and upper basket It is commended that loading the lower basket first than the upper one see the section entitled Loading the Dishwasher 2 Pourinthe detergent see the section entitled Salt Detergent and Rinse Aid 3 Insertthe plug into the socket The power supply is 220 240 VAC 50 Hz the specification of the socket is 10 A 250 VAC Make sure that the water supply is turned on to full pressure 4 press the On Off button and the On Off indicator on Press the Program button to select a desired wash cycle Close the door After 10 seconds the machine will work Change the Programme Premise 1 Acycle that is underway can only be modified if it has only been running fora short time Otherwise the detergent may have already been released and the appliance may have already drained the wash water If this is the case the detergent dispenser must be refilled See the section entitled Loading the Detergent 2 Open the door press the program butt
18. f the dishwasher Note please check the accompanying installation accessories hook for aesthetic panel screw Figure1 Cabinet dimensions Less than 5mm between the top of dishwasher and Electrical drain and cabinet and the EE outer door aligned to cabinet Space between cabinet bottom and floor 450 mm Figure2 Dishwasher Minimum space when the door is opened Minimum space of 50mm Aesthetic panel s dimensions and installation l The aesthetic wooden panel could be processed according to the Figure 3 Figures The aesthetic panel should be processed in accordance with the illustrated dimensions Unit mm Z Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door of dishwasher see figure 4a After positioning of the panel fix the panel onto the outer door by screws and bolts See figure 4b oo Hop hook Figure4a Installation of aesthetic panel _ st4 countersunk head screw Lower hook 4X18 screw Figure4b Cover p Installation of aesthetic Spacer for aesthetic panel Z wooden panel WA 7 Take away the cover 2 Pin up the screw 5 Get back the cover Hook for aesthetic panel Outer door of N dishwasher A Aesthetic panel LC Bee e Tension adjustment of the door spring The door springs are set at the factory to the proper tension for the outer door If ae
19. ic types E conventional alkaline detergents with caustic components E low alkaline concentrated detergents with natural enzymes Detergent Tablets Detergent tablets of different brands dissolve at different speeds For this reason some detergent tablets cannot dissolve and develop their full cleaning power during short programs Therefore please use long programs when using detergent tablets to ensure the complete removal of detergent residuals Detergent Dispenser The dispenser must be refilled before the start of each wash cycle following the instructions provided in the wash cycle table Your dishwasher uses less detergent and rinse aid than Conventional dishwasher Generally only one tablespoon of detergent is needed for anormal wash load More heavily soiled items need more detergent Always add the detergent just before starting the dishwasher otherwise it could get damp and will not dissolve properly Amount of Detergent to Use A Detergent powder Detergent tablet m lfthelidis closed press release button The lid will Spring open Mm Always add the detergent just before starting each wash cycle M Only use branded detergent aid for dishwasher A WARNI NG Dishwasher detergent is corrosive Take care to keep it out of reach of children Proper Use of Detergent Use only detergent specifically made for the use in dishwashers Keep your detergent fresh and dry Don t put powdered detergent into the dispenser until you
20. ign Setting toward the sign fH French degree we Setting toward between the sign and sign Clark British degree Contact your local water board for information on the hardness of your water supply A NOTE If your model does not have any water softener you may skip this section WATER SOFTENER The hardness of the water varies from place to place If hard water is used in the dishwasher deposits will form on the dishes and utensils The appliance is equipped with a special softener that uses a Salt container specifically designed to eliminate lime and minerals from the water B Loading the Salt Into the Softener Always use the salt intended for use with dishwasher The salt container is located beneath the lower basket and should be filled as explained in the following Attention WE Only use salt specifically designed for the use in dishwashers Every other type of salt not specifically designed for the use in a dishwasher especially table salt will damage the water softener In case of damages caused by the use of unsuitable salt the manufacturer does not give any warranty nor is liable for any damages caused E Only fill with salt just before starting one of the complete washing programs This will prevent any grains of salt or salty water which may have been spilled remaining on the bottom of the machine for any period of time which may cause corrosion Remove the lower basket and then unscrew
21. ill the salt container with water Fill the rinse aid dispenser D Fillin detergent A Water Softener The water softener must be set manually using the water hardness dial The water softener is designed to remove minerals and salts from the water which would have a detrimental or adverse effect on the operation of the appliance The higher the content of these minerals and salts the harder your water is The softener should be adjusted according to the hardness of the water in your area Your local Water Authority can advise you on the hardness of the water in your area Adjusting Salt Consumption The dishwasher is designed to allow for adjustment in the amount of salt consumed based on the hardness of the water used This is intended to optimise and customise the level o f salt consumption Please follow the steps below for adjustment in salt consumption 1 Unscrew the cap from the salt container 2 Thereis aring on the container with an arrow on it see figure onthe side if necessary rotate the ring in the anticlockwise direction from the Setting toward the sign based onthe hardness of the water being used Itis recommended that adjustments should be made in accordance with the following scheme WATER HARDNESS o WATER HARDNESS oS NW Salt consumption Auto nomy C os oa OO O y o o S S Note ga SE Note 2 dH 1 25 arke 1 78 fH 0 178mmol No salt need added DH German degree ER setting toward the s
22. k you doing your part to protect the environment 3 Operation Instruction To get the best performance from your dishwasher read all IMPORTANT operating instructions before using It for the first time Control Panel H hehe he EE eet ee Keeseren then you can choose the desired program Delay Start Button Indicator Press this button to select the delay hours for washing You can delay the start of washing up to 3 6 9 12 hours Display Window To show the delay time fault codes and etc Half load functions Button To select Hal f load functions With this Half load function you can only use it when you have only about or less than 5 place setting dish wave and you will see less water and energy consumption can only be used with Intensive Normal Eco Glass and 60 min H Program Indicators To be on when the program be selected Program Button To select washing program when press the button Dishwasher Features Front view E Back View NAN AVITAL ACAL TREANA N ANULA ae E Dee Upper Basket Salt Container Cup Shelf 1 0 Rinse Aid Dispenser Spray Arms Main Filter D Cutlery Basket Drain pipe connector Lower Basket D Detergent Dispenser 9 Coarse Filter Inlet pipe connector 3 4 Prior using for the first time Before using your dishwasher for the first time set the water softener D Add 1 5Kg dishwasher salt and then full f
23. nd glasses In this case please add more detergent to reach better results Detergents without chlorine do only bleach a little Strong and coloured spots will not be removed completely In this case please choose a program with a higher temperature Useof 2in1 3in1 4in1 and 5in1 Combination Compact Detergents These products are detergents with integrated and combined detergent rinse aid and salt functions Before using these products you should first check that the water hardness in your supply is compatible with the use of these products as per the detergent manu facturers onthe product packaging These products should be strictly used according to the detergent manufacturer s instructions In general detergents that include rinse aid or water softener are only able to serve good results under certain conditions rinse aid and water softener can not adapted to specific conditions For this reasons in some cases there might be unwanted cleaning or drying results Please ask the detergent manufac turer to inform you about the best consume conditions If you encounter problems when using these products for the first time then please contact the detergent manufacturers care line The manufacturer of your dishwasher is not liable for damages caused by compact detergents nor gives warranty if you use compact detergents When use 2in1 3in1 4in1 or 5in1 Combination Compact Deter gents please pa
24. not empty your dishwasher immediately after washing Open the door slightly so that the steam can escape Begin unloading the dishwasher only oncet he dishes are barely warm to the touch Empty the low basket first This prevents water form dropping off dishes in the upper basket In short program the washing temperature is lower This also lowers cleaning performance Choose a program with along washing time Water drainage is more difficult with these items Cutlery or dishes of this type are not suitable for washing inthe dishwasher When some inattunctons come on the aoohancle WI display error codes lo Warn you Codes Meanings Possible Causes Faucets is not opened or water intake is restricted or water pressure E1 Longer inlet time is too low E4 Overfilled Too much inlet water m f overflow occurs turn off the main water supply before calling a Service A WARNING m f there is water in the base pan because of an overfill or small leak the water should be removed before restarting the dishwasher Technical information 26 Technical Data Sheet Sheet of household dishwasher according to EU Directives 1016 2010 amp 1059 2010 a K A highest efficiency to D lowest efficiency Energy consumption 238 kWh per year based on 280 standard cleaning cycles using cold water fill and the consumption of the low power modes Actual energy consumption will depend on how the appliance is u
25. nse aid into the dispenser being careful not to overfill Replace the cap by inserting it aligned with open arrow and turning it to the closed right arrow Be careful not to overfill the dispenser because this could cause over sudsing Wipe away any spills with a damp cloth Don t forget to replace the cap before you close dishwasher door Attention Clean up any rinse aid split during filling with an absorbent cloth to avoid excess foaming during the next wash Adjusting Rinse Aid Dispenser The rinse aid dispenser has six scales Always start with the dispenser set on 4 Adjustlever f spots and poor drying area problem increase the amount of rinse aid dispensed Rinse by removing the dispenser lid and rotating the dial to 5 If the dishes still are not drying properly or are show spots adjust the dial to the next higher lever until your dishes are spot free The recommended setting is A Factory value is A A NOTE Increase the dose if there are drops of water or lime spots on the dishes after washing Reduce it if there are sticky whitish stains on your dishes or a bluish film on glassware or knife blades D Function of Detergent Detergents with its chemical ingredients are necessary to remove dirt crush dirt and transport it out of the dishwasher Most of the commercial quality detergents are suitable for this purpose Concentrated Detergent Based on their chemical composition detergents can be split in two bas
26. on and hold more than 3 seconds then press the program button to select the desired wash cycle see the section entitled Starting a wash cycle NOTE If you open the door when washing the machine will pause When you close the door the machine will keep on working after 10 seconds The Program indicators show the state of the dishwasher a All program indicators are off gt Stand by b One of the program indicators is on gt Pause c One of the program indicators is blinking gt Run NOTE if all the lights begin to glimmer that indicates the machine is out of order please turn off the main power and water supply before calling a service Forget to Add a Dish A forgotten dish can be added at any time before the detergent cup opens l Open the door a little to stop the washing 8 Load the forgotten dishes ZS After the spray arms stop working you can open the door amp Close the door the dishwasher will start running again completely after 10 seconds A WARNING It is dangerous to openthe door when washing because the hot water may scald you At the End of the Wash Cycle When the working cycle has finished the buzzer of the dishwasher will sound for 8 seconds then stop Turn off the appliance using the ON OFF button shut off the water supply and open the door of the dishwasher Wait for a few minutes before unloading the dishwasher to avoid handling
27. per items Glazed patterns may fade if machine Crystal glass washed frequently Steel items subject to rusting Wooden platters Items made from synthetic fibres NOTE Do not putin items that are dirty of cigarette ash candle wax lacquer or paint If you buy new dishes please make sure that they are suitable for dishwashers NOTE Please do not overload your dishwasher Do not use dish that is not suitable for dishwashers This is important for good results and for reasonable energy consume Loading cutlery and dishes Before loading the dishes you should Remove large left over Soften remnants of burnt food in pans When loading the dishes and cutlery please note Dishes and cutlery must not impede the rotation of the spray arms Load hollow items such as cups glasses pans etc withthe opening downwards So that water cannot collect in the container or adeep base Dishes and items of cutlery must not lie inside one another or cover each other M Toavoid damage to glasses they must not touch E Load large items which are most difficult to clean into the lower rack M The upper rack is designed to hold more delicate and lighter dishware such as glasses coffee and teacups Attention Long bladed knives stored in an upright position are a potential hazard Long and or sharp items of cutlery such as carving knives must be positioned horizontally inthe upper basket Damage to glas
28. pliance slightly ajar This will help Remove the Plug the seals to last longer and prevent odours from forming Before cleaning or performing maintenance always within the appliance remove the plug from the socket Do not run risks Movin the A liance No Solvents or Abrasive Cleaning H ER 7 If the appliance must be moved try to keep it in the vertical To clean the exterior and rubber parts of the dishwasher position If absolutely necessary it can be positioned on do not use solvents or abrasive cleaning products its back Rather use only a cloth and warm soapy water Seals To remove spots or stains from the surface of the interior use a cloth dampened with water and a little One of the factors that cause odours to form in the vinegar or acleaning product made specifically for dishwasher is food that remains trapped in the seals dishwashers Periodic cleaning with a damp sponge will prevent this from occurring 8 nstallation instruction Warning A Attention Electrical Shock Hazard The installation of the pipes Disconnect electrical power before and electrical equipments installing dishwasher should be done by professionals Failure to do so can result in death or electrical shock e Installation preparation The installation position of dishwasher should be near the existing inlet and drain hoses and power cord One side of the cabinet sink should be chosen to facilitate the connection of drain hoses o
29. pped with a cord having an equipment earthing conductor and an earthing plug The plug must be plugged into an appropriate Outlet that is installed and earthed in accordance with all local standards and requirements Improper connection of the equipment grounding conductor can result in the risk of anelectric shock Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded Do not modify the plug provided with the appliance If itis not fit for the outlet Have a proper outlet installed by a qualified electrician How to Connect the safety supply hose The appliance must be connected to the water mains using new hose sets The old hose sets should not be reused Water pressure must be between 0 04 MPa and 1 MPa If the pressure is below the minimum consult our Service Department for advice TI Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher 2 Tighter the screws of the safety supply hose to the faucet with thread 3 4inch mm d Al 5 Turn water fully on before starting the dishwasher ABOUT THE SAFETY SUPPLY HOSE The safety supply hose consists of the double walls The hose s system guarantees Its intervention by blocking the flow of water in case of the supply hose breaking and when the air space between the supply hose itself and the outer corrugated hose is full of water A WARNING A hose th
30. s filter gently squeeze the taps on the top of this filter and lift it out Fine filter This filter holds soil and food residues in the sump area and prevents it from being redeposit on the dishes during a cycle Inspect the filters for blocking after every time the dishwasher has been used By unscrewing the coarse filter you can remove the filter system Remove any food remnants and clean the filters under running water step 1 Turn the filter in anti clockwise direction then lift it up Step 2 lift the Main filter up Step 3 lift the Fine filter up NOTE When following this procedure from step to step 3 the filter system will be removed when following it from Step 3 to Step 1 the filter system will be installed Filter assembly For best performance and results the filter assembly must be cleaned The filter efficiently removes food particles from the wash water allowing it to be recycled during the cycle For best performance and results the filter must be cleaned regularly For this reason it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the semicircular filter and cup under running wa
31. sed Water consumption 2940 litres per year based on 280 standard cleaning cycles Actual water consumption will depend on how the appliance is used A highest efficiency to G lowest efficiency This program is suitable for cleaning soiled normally soiled tableware and that itis the most efficient programme in terms of its combined energy and water consumption for that type of tableware The device meets the European standards and the directives in the current version at delivery LVD 2006 95 EC EMC2004 108 EC EUP 2009 125 EC The above values have been measured in accordance with standards under specified operating conditions Results may vary greatly according to quantity and pollution of the dishes water hardness amount of detergent etc The manualis based on the European Union s standards and rules 21
32. sthetic wooden panel are installed you will have to adjust the door spring tension Rotate the adjusting screw to drive the adjustor to strain or relax the steel cable see figure 5 Door spring tension is correct when the door remains horizontal in the SC fully opened position yet rises to aclose with the slight lift ofa finger Figured Tension adjustment of the door spring e Connection of drain hoses Insert the drain hose into a drain pipe with a minimum diameter of 4cm or let it run into the sink making sure to avoid bending or crimping it Use the speicalplastic support that comes with the appliance figure 6 The top of the hose must be at a height between 40 and 100cm The free end of the hose must not be immersed in water ATTENTION The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain Figure6 Drain pipe connection Al PLEASE HANG UP THE DRAIN HOSE EITHER WAY OF A B C Close the drain hose hook to the counter Drain hose hook z D z CO Ze lt e Dishwasher installation steps 1 Install the furniture door to the outer door of the dishwasher using the brackets provided Refer to the template for positioning of the brackets 2 Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to tighten the left and right door springs Failure to do
33. supply is connected properly and the water is turned on Make sure to close the door properly and latch it Check drain hose Check coarse the filter see section titled Cleaning The Filter Check the kitchen sink to make Sure it is draining well Ifthe problem is the kitchen sink not draining you may need aplumber rather than a serviceman for dishwashers Use only the special dishwasher detergent to avoid suds lf this occurs open the dishwasher and let suds evaporate Add 1 gallon of cold water to the tub Close and latch the dishwasher then Start the soak wash cycle to drain out the water Repeat if necessary Always wipe up rinse aid spills immediately Make sure that the detergent is the one without colourant To clean the interior use a damp sponge with dishwasher detergent and wear rubber gloves Never use any other cleaner than dishwasher detergent for the risk of foaming or suds Always run the quick wash programme without any crockery in the dishwasher and without selecting the Turbo function if present after adding dishwasher salt Check the lip Ensure the fix Is fine Interrupt the programme and rearrange the items which are obstructing the spray arm Interrupt the programme and rearrange the items of crockery This has no influence on the dishwasher function if in doubt contact a suitably qualified plumber Problem The dishes are not clean Unsatis factory washing result
34. sware and other dishes Possible causes Type of glass or manufacturing process Chemicalcomposition of detergent Water temperature and duration of dishwasher programme Suggested remedy Use glassware or porcelain dishes that have been marked dishwasher proof by the manufacturer Use amild detergent that is described as kind of dishes If necessary seek further information from detergent manufacturers Select a programme with as low atemperature To prevent damage take glass and cutlery out of the dishwasher as soon as possible after the programme has ended 6 Starting a washing programme WASH CYCLE TABLE Cycle Selection TELS Information For heaviest soiled crockery eg and normally soiled pots eg pans dishes etc with dried Intensive on soiling For normally soiled loads such as pots plates glasses and lightly Soiled pans This is Standard programme it is Suitable to clean normally soiled tableware and it is the Eco most efficient programme in teams of its combined energy and water consumption for that type of tableware EN 50242 For lightly soiled crockery and glass For lightly soiled loads that do not need excellent drying efficiency A shorter wash for lightly Soiled loads and quick wash Running Energy Water Rinse timetmin Kwh m Aid Detergent Bre main Description of Cycle Prewash 50 C Wash 65 C Rinse 3 229 120 1 13 16 Rinse Rinse 55 C Drying Pr
35. ter To remove the filter device pullthe cup handle in the upward direction The entire filter assembly should be cleaned once a week To clean the coarse filter and the fine filter use a cleaning brush Then reassemble the filter parts as shown in the figures left and reinsert the entire assembly in the dishwasher positioning in its seat and pressing downward The dishwasher must never be used without the filters Improper replacement of the filter may reduce the performance level of the appliance and damage dishes and utensils A WARNING m Jhedishwasher must never be used without the filters E Improper replacement of the filter may reduce the performance level of the appliance and damage dishes and utensils Cleaning the Spray Arms It is necessary to clean the spray arms regularly for hard water chemicals will clog the spray arm jets and bearings Remove the upper spray arm To remove the upper spray arm screw off the nut clockwise then remove the arm Remove the lower spray arm To remove the lower spray arm pull out the spray arm upward Wash the arms Wash the arms in soapy and warm water and use a soft brush to clean the jets Replace them after rinsing them thoroughly Caring for the Dishwasher The control panel can be cleaned by using a lightly dampened cloth After cleaning make sure to dry it thoroughly For the exterior use a good appliance polish wax Never use Sharp objects scouring pads or harsh
36. ter dishware such as glasses coffee and tea cup and saucers as wellas plates small bowls and shallow pans as long as they are not too dirty Position the dishes and cookware so that they do not get moved by the spray of water y D IN 1 Cups 1 28 2 Small serving bowl p ean k 3 Large serving bowl K S i 4 Glasses a E 5 Saucers Ze 6 Dish H Dessert dishes a d Be J p s Adjusting the Upper Basket The height of the upper basket can be adjusted in order to create more space for large utensils both for the upper lower basket The height of the upper basket can be adjusted by placing the wheels on different height of the rails Long items serving cutlery salad servers and knives Should be placed onthe shelf so that they do not obstruct the rotation of the spray arms The shelf can be folded back or be removed when not required for use Upper wheels Loading the Lower Basket We recommend that you place large items which are most difficult to clean into the lower basket pots pans lids serving dishes and bowls as shown inthe figure to the right It is preferable to place serving dishes and lids onthe side of the racks in order to avoid blocking the rotation of the top spray arm Pots serving bowls etc must always be placed top down Deep pots should be slanted to allow water to flow out The bottom basket feature fold down tine rows So that larger or more pots and pans can be loaded 7 Dessert
37. wing water to roll off the dishes Your dishwasher is designed to use liquid rinse aids The rinse aid dispenser is located inside the door next to the detergent dispenser To fillthe dispenser open the cap and pour the rinse aid into the dispenser until the level indicator turns completely black The volume of the rinse aid container is about 110ml Function of Rinse Aid Rinse aid is automatically added during the last rinse ensuring thorough rinsing and spot and streak free drying Attention Only use branded rinse aid for dishwasher Never fill the rinse aid dispenser with any other substances e g Dishwasher cleaning agent liquid detergent This would damage the appliance When to Refill the Rinse Aid Dispenser If there is no rinse aid warning light in the control panel you can judge the amount of rinse aid by the color of the optical level indicator C located next to the cap When the rinse aid container is full the whole indicator will be dark Ae the rinse aid diminishes the size of the dark dot decreases You should never let the rinse aid get below 1 4 full C Rinse Aid indicator As the rinse aid diminishes the size of the black dot on the rinse aid level indicator changes as illustrated below Full 3 4 full 1 2 full 1 4 full Should refill to eliminate spotting O Empty RINSE AID DISPENSER To open the dispenser turn the cap to the open left arrow and lift it out Pour the ri
38. y attention to make sure that the size of the Combination Detergents is fitted to the dispenser so that Combination Detergents can be ease to putin the dispenser and dispenser would not be broken Attention Keep all detergents in a safe place out of children s reach Always add the detergent in the dispenser just before starting the dishwasher 5 Loading the Dishwasher Basket For best performance of the dishwasher follow these loading guidelines Features and appearance of baskets and cutlery baskets may vary from your model Attention before or after Loading the Dishwasher Baskets Scrape off any large amounts of leftover food Soften remnants of burnt food in pans lt is not necessary to rinse the dishes under running water Place objects in the dishwasher in following way 1 ltems suchas cups glasses pots pans etc are faced downwards 2 Curved items or ones with recesses should be loaded aslant so that water can run off 3 All utensils are stacked securely and can not tip over 4 All utensils are placed in the way that the spray arms can rotate freely during washing Very small items should not be washed in the dishwasher as they could easily fall out of the baskets Removing the Dishes To prevent water dripping from the upper basket into the lower back we recommend that you empty the lower basket first and then the upper basket Loading the Upper Basket The upper basket is designed to hold more delicate and ligh
Download Pdf Manuals
Related Search