Powerplus POWX027 power drill
Contents
1. aw Vibration 18 5m s2 K 1 5 m s Copyright 2014 VARO Page 6 www varo com POWERPLUS POWX027 EN a WARRANTY This product is warranted for a 36 month period effective from the date of purchase by the first user This warranty covers all material or production flaws excluding batteries chargers defective parts subject to normal wear amp tear such as bearings brushes cables and plugs or accessories such as drills drill bits saw blades etc damage or defects resulting from maltreatment accidents or alterations nor the cost of transportation Damage and or defects resulting from inappropriate use also do not fall under the warranty provisions We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool Repairs may only be carried out by an authorised customer service centre for Powerplus tools You can always obtain more information at the number 00 32 3 292 92 90 Any transportation costs shall always be borne by the customer unless agreed otherwise In writing At the same time no claim can be made on the warranty if the damage of the device is the result of negligent maintenance or overload s Definitely excluded from the warranty is damage resulting from fluid permeation excessive dust penetration intentional damage on purpose or by gross carelessness inappropriate usage use for purposes for which the device is not suitable incompetent usage e g n2. Do not allow children to have access Make sure you have a secure stand on ladders or scaffolding when using the drill freehand Localize lines with a line detector in walls where power water or gas lines are laid invisibly Wear protection goggles and use a dust mask for dust producing work Always arrange for a qualified electrician to carry out repairs Use only original replacement parts The level of noise at the workplace may exceed 85 dB A In this case you will need to introduce noise protection measures for the user The noise generated by this electric tool was measured in accordance with EN 50114 1 Copyright 2014 VARO Page 4 www varo com POWERPLUS POWX027 EN HIGH QUALITY TOOLS Always use ear protection when machine is in use Recommended nominal operating time approx 20 minutes under permanent load Rest after permanent operation approx 5 10 minutes 7 OPERATION WARNING Prior to assembly and adjustment always pull out the power plug from the mains socket 7 1 Switching on off Fig 1 Plug the cord set into power socket To start the tool by squeezing the ON OFF switch 4 Release the ON OFF switch to stop the tool If you press the lock on button 6 while the ON OFF switch is depressed the ON OFF switch is kept in the operating position To release the ON OFF switch 4 and turn the tool off 7 2 Forward reverse lever Fig 2 The forward reverse lever 3 is to determine
3. tool s operation If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to stick and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could lead to a hazardous situation 5 5 Service Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained 6 ADDITIONAL SAFETY HINTS FOR IMPACT DRILL Do not use near steams or inflammable liquids Only use sharp bits and suitable screwing bits Remove the plug from the socket for all adjusting and cleaning work Protect the mains cable against any damage Oil and acids can damage the cable Do not carry the device by the mains cable Do not remove the plug from the socket by puffing the mains cable Make sure before inserting the plug that the operating switch is not locked When using a cable drum uncoil the cable completely Cross section of wire at least 1 5 mm2 Do not overload machine Secure all work pieces to be processed sufficiently
4. POWERPLUS HIGH QUALITY TOOLS POWX027 EN 1 E 2 2 DESCRIPTION FIG A ccccccceseeceeneecenseecenseeceaseecensesenneesenseees 2 3 PACKAGE CONTENT LIST cccsscccceseeceeseecenseecensesenseesenseess 2 4 H 2 5 GENERAL POWER TOOL SAFETY WARNINGS 0 3 5 1 WOK ar isseire aar 3 5 2 ERON SA E 3 5 3 EELER 3 5 4 P wer lool USC and CAC sicicassia ca cdecesccetesccecetesccedeadoca eai R a aai 4 55 ee d 6 ADDITIONAL SAFETY HINTS FOR IMPACT DRILL 4 T OTS O vs ccnssencnesencnsncunsecenesecenasenenenencnsnsusasnsunasesenesenenenensnessonss 5 7 1 Switching on off Fig 1 5 7 2 Forward reverse lever Fig 2 cciiessscesicsisccssatsserssncesaestnacicerinndvecetetevscusevesssedensdenctenes 5 7 3 Variable speed FIG 3 crrr recon eanucessiesnderetssntdsais meesoeeeneemene 5 7 4 Drill and impact mode selector Fig 4 scccccccenneecceceeeensnneeseeeennenneesseeeenannssssseees 5 7 5 FOr Prop rf E irer E EE REE ER 5 O ooo ccccnseccnnsecenesenenenenenenencnsnsucnsnsunusesenesesenenenenensusassses 6 E 6 10 O E A E E 6 11 T 12 E EN 7 13 DECLARATION OF CONFORMITY ccccesseeceneeeceneeeeeneees 8 Copyright 2014 VARO Page 1 www varo com POWERPLUS POWX027 EN HIGH QUALITY TOOLS IMPACT DRILL 910W POWX027 1 APPLICATION The power tool is intended for driving and drilling through wood metal plastics and masonry It is not designed for commercial use
5. RPLUS POWX027 EN 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and all instructions Failure to follow all warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool 5 1 Work area Keep work area clean and well lit Cluttered and dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep children and bystanders away while operating a power tool Distractions can cause you to lose control 5 2 Electrical safety Always check that the power supply corresponds to the voltage on the rating plate Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Do not abuse the cord Never use the cord fo
6. and keep it for your future reference Your power tool should only be passed on with these instructions CC WARNING Please read and understand this operating manual before use DESCRIPTION FIG A Keyless chuck with auto lock 5 Speed control selector Switch drilling impact drilling 6 Lock button Switch right left action 7 Additional handle Operating switch 8 Depth stop PACKAGE CONTENT LIST Remove all packing materials Remove remaining packaging and transit supports if existing Check the completeness of the packing content Check the appliance the power cord the power plug and all accessories for transportation damages Keep the packaging materials as far as possible till the end of the warranty period Dispose it into your local waste disposal system afterwards e O AON WARNING Packing materials are no toys Children must not play with plastic bags Danger of suffocation 1 x impact drill 1 x additional handle 1 x depth stop 1 x manual i When parts are missing or damaged please contact your dealer 4 SYMBOLS The following symbols are used in this manual and or on the machine In accordance with essential requirements of the European directive s Class Il The machine is Read manual before use double insulated Earthing wire is therefore not necessary Denotes risk of personal injury or damage to the tool Wear eye protection Wear gloves Copyright 2014 VARO Page 2 www varo com POWE
7. drill bits Use enough pressure to keep the bit biting but do not push so hard that do not stall the motor or damage the bit Always apply pressure in a straight line with the bit Hold the drill firmly to control the twisting of the drill Warning If the drill stalls release the trigger immediately remove the drill from the work and determine the cause of the stalling Do not click the switch on and off as this can damage the motor To minimize the chance of stalling and breaking through the material reduce the pressure on the drill and ease the bit through the last part of the hole Keep the motor running when pulling the bit back out of a drilled hole This will help prevent jamming 8 MAINTENANCE Do not attempt to make any adjustments while the tool is in operation Clean out any accumulated dust with a brush or dry cloth Do not allow petroleum based products to come into contact with plastic parts as they contain chemicals which could damage weaken or destroy plastic 9 TECHNICAL DATA Mains voltage 230 240V 50Hz Power input 910W No load speed 0 3000 min Chuck capacity 13mm Double isolation Yes Impact rate 0 54000 min Max drill capacity Wood 30mm Steel 13mm Concrete 16mm 10 NOISE Noise emission values measured according to relevant standard K 3 Acoustic pressure level LpA 98 dB A Acoustic power level LWA 109 dB A ATTENTION Wear hearing protection when sound pressure is over 85 d dB A
8. oduct Impact Drill Trade mark PowerPlus Model POWX027 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives based on the application of European harmonized standards Any unauthorized modification of the apparatus voids this declaration European Directives including if applicable their amendments up to the date of signature 2011 65 EU 2004 108 EC 2006 42 EC European harmonized standards including if applicable their amendments up to the date of signature EN60745 1 2009 EN60745 2 1 2010 EN55014 1 2006 EN55014 2 1997 EN61000 3 2 2006 EN61000 3 3 2008 Keeper of the Technical Documentation Philippe Vankerkhove VARO Vic Van Rompuy N V The undersigned acts on behalf of the company CEO Philippe Vankerkhove Regulatory Affairs Compliance Manager Date 04 03 2014 Copyright 2014 VARO Page 8 www varo com
9. ot following the instructions given in the manual inexpert assembly lightning strike erroneus net voltage This list is not exhaustive Acceptance of claims under warranty can never lead to the prolongation of the warranty period nor commencement of a new warranty period in case of a device replacement Devices or parts which are replaced under the warranty therefore remain the property of Varo NV We reserve the right to reject a claim whenever the purchase cannot be verified or when it is clear that the product has not been properly maintained Clean ventilation slots carbon brushes serviced regularly etc Your purchase receipt must be kept as proof of date of purchase Your appliance must be returned undismantled to your dealer in an acceptably clean state in its original blow moulded case if applicable to the unit accompanied by proof of purchase 12 ENVIRONMENT Should your appliance need replacement after extended use do not discard it with the household rubbish but dispose of it in an environmentally safe way Waste produced by electrical machine items should not be handled like normal household rubbish Please recycle where recycle facilities exist Check with your Local Authority or retailer for recycling advice Copyright 2014 VARO Page 7 www varo com POWERPLUS POWX027 EN HIGH QUALITY TOOLS 13 OF CONFORMITY vard VARO N V Joseph Van Instraat 9 BE2500 Lier BELGIUM declares that Pr
10. r carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock f operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock 5 3 Personal safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Use safety equipment Always wear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used whenever conditions require will reduce personal injuries Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury Do not overreach Keep proper footing and balance at all times This enable
11. s better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts Copyright 2014 VARO Page 3 www varo com POWERPLUS POWX027 EN HIGH QUALITY TOOLS f devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of these devices can reduce dust related hazards 5 4 Power tool use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or sticking of moving parts breakage of parts and any other condition that may affect the power
12. the rotation direction of the chuck To select forward rotation release the ON OFF switch 4 and push the forward reverse lever to right R side of the tool To select reverse rotation push the lever to left L side of the tool _ NOTE When changing the position of the lever be sure the ON OFF switch is released and the motor is stationary 7 3 Variable speed Fig 3 This tool has a speed control dial 5 that delivers higher speed by turning to the and delivers lower speed by turning to direction direction 7 4 Drill and impact mode selector Fig 4 The drill and impact mode selector is on the top of this impact drill Push the button of drill impact mode selector 2 to the T to select the drill impact mode of action A Push the button of drill impact mode selector to the drill position 4 to select the drill mode of action The drill and impact mode selector is on the top of this impact drill 7 5 For Proper Operations WwWwwW varo com Copyright 2014 VARO POWERPLUS POWX027 EN HIGH QUALITY TOOLS Hold the drill with your first two fingers on the ON OFF switch 4 Use the auxiliary handle subassembly 7 where possible to gain extra control and to prevent fatigue For wood use twist drill bits soade bits power auger bits or hole saw For metal use high seed steel twist drill bits or hole saws For masonry such as brick cinder block cemetery etc use carbide tipped
Download Pdf Manuals
Related Search