Home

Sencor SLE 1956M4

image

Contents

1. M DOUDQUDONNE POOUDOUDOUOD DONOONUUDLR ce ononon l ee aaa INUOCUCONOCoLONA cp aeon M4 x 12 4 4 When installing the TV stand place the TV screen on a soft surface so as to prevent damaging the surface of the device EN 15 Copyright 2013 Fast C R a s Revision 04 2013 EN Before using 3 2 Wiring diagram THITTT LTT TRIETELT Note You should connect all the necessary cables BEFORE connecting the power cord 16 EN Copyright 2013 Fast CR a s Revision 04 2013 Basic controls EN 4 Basic controls 4 1 Turning on As soon as the device is placed attached in a suitable location on a table or on a wall and all the necessary cables have been connected including the power cord do t
2. Press the A V button to select a file which you wish to play then in the file selection menu press the OK button or II to start playback Press the W or EXIT button to interrupt playback Use the W button to return to the previous menu i Han 148_CONT 3F mp4 VersaEmerge_Toxic_Cover_0_av you give love a Sed name ayi ab Cater Information about the currently played file will appear for several seconds after starting or after the DISPLAY button is pressed EN 57 Copyright 2013 Fast CR a s Revision 04 2013 f 10 4 PVR Menu Press the lt P button to select PVR in the main menu then press the OK button to enter Press the EXIT button to return back to the previous menu Press the A V button to select a file which you wish to play then in the file selection menu press the OK button or II to start playback Information about the currently played fi ile will appear for several seconds after starting or after the DISPLAY button is pressed Then press the II button to start playback in the right hand part of the screen Note Other functions are the same as the Movie menu 58 EN Copyright 2013 Fast CR a s Revision 04 2013 om 10 5 E Book Menu Book Reader Press the lt P gt button to select E Book Book Reader in the main menu then press the OK button to enter Press the EXIT button to return back to the previous menu Press the A V button to
3. AUNORS Cannes IUII Picture Oegital channels bound Sound z meo erasida Channel lt a Feature mt Setup es Ear As soon as the automatically search is finished a message screen will appear after a few Seconds confirming that the found channels have been saved 4 5 5 Analogue Manual Search Use the A F buttons to select the item Analogue Manual Search and then use the OK or button to enter the submenu If the lock has been set you will be asked to enter a password O0000 l Sound fine Tune E nel Channel Feature tetu 4 5 6 Current Channel Use the OK or P button to enter the menu then use the A W buttons to select the item Current Channel Use the A V buttons to select the current channel and then use the OK or P button to confirm 26 EN Copyright 2013 Fast R a s Revision 04 2013 Basic controls EN 4 5 7 Search Use the A V buttons to select the item Search and then use the OK or P button to enter the submenu The following screen will appear and then use the lt P buttons to search for a channel yo as2swne D 4 5 8 Color System Use the A F buttons to select the item Color System and then use the OK or P button to enter the submenu Use the A V buttons to choose from Auto PAL SECAM the use the OK or P button to confirm 4 5 9 Sound System Use the A V buttons to select the item Sound System and then use the OK or gt button to enter t
4. Lock You can press the HOLD button to lock the teletext page To cancel the page lock press this button again Index Press the INDEX page to display contents pages Enter a specific teletext page using the numerical buttons Zooming in teletext If a teletext page is displayed you can zoom in to double the size of this page Press the SIZE button to zoom into the top half of the teletext page Press the SIZE button again to zoom move to the bottom part of the teletext page Press this button once more to return to the original display Display mode Press the REVEAL button to show hidden teletext information Press this button again to cancel Coloured buttons red green yellow and blue Select the appropriate teletext page using the coloured buttons EN 47 Copyright 2013 Fast CR a s Revision 04 2013 EN SCART AV COMPONENT Settings Menu 7 SCART AV COMPONENT Settings Menu The Picture Menu is the same as in the previous part of this user s manual The Sound Menu is the same as in the previous part of this user s manual The Channel Menu is not accessible items are greyed out The Feature Menu is the same as in the previous part of this user s manual The Setup Menu is the same as in the previous part of this user s manual Note The following screen will appear if there is no signal from the input source DIV ATV SCART AV COMPONENT No signal The device automatically switches to stand by m
5. TV RADIO button Serves to switch between TV and RADIO modes DTV mode SCALER button Serves to watch the picture in various formats MIX button Serves to combine teletext with a TV program ATV mode a VA a a Serves to fast rewind DVD Media modes Hold it down for approx 3 seconds to skip to the previous chapter track image DVD Media modes TEXT button Turns teletext on or off ATV DTV mode PP gt P Serves to fast forward DVD Media modes Hold it down for approx 3 seconds to skip to the next chapter track image DVD Media modes SIZE button Serves to increase the TV picture in teletext ATV mode ZOOM Serves to zoom in on a displayed picture DVD mode ZOOM button Serves to zoom out of a displayed picture DVD mode SLEEP button Serves to set the TV sleep timer Only on models with a DVD player EN 13 Copyright 2013 Fast CR a s Revision 04 2013 EN Remote control Note Remove the batteries if you will be storing the device or not using it for an extended period of time e To control the device using the remote control point the remote control at the device and then press the button with the required function The effective range of the remote control is up to about 5 meters with a maximum deviation of 30 from the perpendicular direction to the reception sensor of the remote control on the front side of the device The falling capacity of the batt
6. 16 REVEAL button Serves to reveal hidden information such as answers to a quiz in teletext ATV mode gt Il Starts pauses playback USB DVD modes Time shift function Time shift DTV modes 17 S PAGE button Serves to display a subpage in teletext ATV mode DVD MENU Serves to display the DVD menu DVD mode 18 HOLD button Holding the current display in teletext ATV mode TITLE Serves to display the contents of a DVD title DVD mode 19 EJECT button Serves to eject the DVD disc DVD mode 20 MUTE button Serves to immediately silence the system and to renew the TV volume 21 RECALL button Serves to switch to the previous last watched channel ATV DTV mode 22 SOURCE button Serves to select an input signal source 12 EN Copyright 2013 Fast CR a s Revision 04 2013 23 24 25 26 27 28 29 30 31 32 33 34 Remote control EN S TITLE button Serves to select subtitles which are broadcast together with the program DTV mode SUBTITLE Serves to select subtitles in DVB made OK button Serves to confirm a selection FAV button Serves to display a list of favourite channels ATV DTV mode CH buttons Press to switch between individual channels PAGE buttons Serves to skip to the next previous page in teletext ATV mode Serves to zoom in out of a displayed picture USB mode P MODE button Serves to select a picture mode
7. Daily Weekly Monthly Recorded List Use the A V buttons to select Recorded List then use the OK or P button to enter the submenu and the following screen will appear 5 2 2 Hearing Impaired Use the A V buttons to select Hearing Impaired the use the OK or P button to enter the submenu and use the OK or A V button to select On or Off Confirm using the OK or gt button EN 41 Copyright 2013 Fast CR a s Revision 04 2013 E 5 2 3 CI Information Use the A V oe to select Cl Information then use the OK or P button to enter the submenu and the following screen will appear Press OK or P to enter Notes This is only an example Other CI modules may have different menus Other menus and descriptions are the same as in the preceding part of this Users manual 5 3 Channel List Press the LIST button on the remote control to display the channel list menu Channel List All Programs YLE TV1 YLE TV2 MTV3 Nelonen YLE FST Sbutv YLE24 MTV3 MAXSbutx Y Enter Use the A to select a channel that you wish to display and press the OK button 42 EN Copyright 2013 Fast CR a s Revision 04 2013 om 5 4 FAV List Press the FAV button on the remote control to display the favourite channels list menu a Favorite gt MIY3 MTV3 MAASbulx JiM Use the A F to select a channel that you wish to display and press the OK button Use t
8. Do not use or leave the device in the vicinity of an open fire e The device must not be exposed to dripping or running water and objects filled with water must not be placed on it e g vases Protect the device against rain spray or contact with any other liquid do not leave or install the device outdoors Do not use the device outdoors Not adhering to these instructions creates a risk of electrical shock or fire hazard e Do not use this device near water e Treat the glass panels and the device cover with care The screen glass can break on impact and cause serious injuries e Make sure that the power cord is not stepped on or compressed particularly near the power plug power socket and at the point where it exits the device or the adapter The power plug adapter is used as a disconnection device and must be easily accessible e Never use a device with a damaged power cord or plug If the power cord or plug are damaged turn off the device disconnect it from the power source and contact an authorised service centre A damaged power cord or plug may only be replaced by qualified personnel Under no circumstances attempt to replace the power cord or plug yourself e Do not try to circumvent the polarised power plug safety feature If the power plug Cannot be inserted into your power socket contact a qualified electrician to replace the old type of power socket e Before connecting the device into a power socket check that the voltage
9. EE AEE Ce E E E IE EAEE 1 7 PA TURING TTT OIG E dense trie ascent cerene E an silane vaca nied deeenaneasiecnustenstuseimenae 17 a E E E Ne E E E V AS Picture Menu PiCtUTG eacnennnennen ann n R EE EEEE 18 AA Sound Menu Cound sessen ninii aA Nei 20 45 Channel Menu Channel cee ccccceecccccccsesseceecscseecescseeceevscssecevsceseeavscestevssstesevsteteesees 22 A VIC IOI orea E 27 47 Setup Menu SettingS cececceecccscsesesscsesesscsesesecsessecsvssecsvsusesevsususecsvsusevevsusevevsnsesevevenseee 30 E E i T EE EEE EAEE EA OAE EEN a5 ak Crni Venuto eeraa ee EE ATN ROAR 36 5 2 Feature Menu FUNCHOMS sensiando eni e iN E EEEE A ETAETA da 38 5 3 Channel List List of Channels ninn nnn nnn 4 Sa PI I ages acess E 43 5 5 Subtitle GSUBILOS eneren A TE N EEE T E 43 5 6 EPG Electronic Program Guide occ ccccccesecscscscsesesesssvsestsesesevsvsvsesesesessesvsnsnesecens 44 Sye MURS U arse ec Setanta heen E E AEE A 45 aed teens eae tein ates tes verses ENA erates ASE 4 7 SCART AV COMPONENT Settings MenU s in 48 ie TI Mecsas ee ence eee see ee eect eee 49 81i Setup Menu Seling eeseneiigsn EE E 49 DA PDM Seip AOM SEWN sasicusscieacsssssissnsacessasaaautstvignondast ayeaundeestiveubbencantsencan EEE 49 E RETE E ce ANN TN O ee 5 di Se Meno SSNS sertie raa i a E EES 51 GZ PG Se UGS SOU GS cuts osoiecenanecoricevehieccasnstindseted svutoitiaesiaututrtesosnedieyseaneiniatntanencinesesdnees 51 1 U E OPCA eee AETA EEEREN EAEE EENES Se
10. button to enter the submenu A request for the entry of a password will appear if the child lock is activated Use the cursor to enter the password OOOO The following screen will appear EN 31 Copyright 2013 Fast CR a s Revision 04 2013 EN Basic controls Do you want to reset Database to default Select Cancel to return to the previous menu and press OK Select OK and press the OK button shortly the reset menu will appear The screen with the initial settings will appear Press the EXIT button to completely exit the menu and ignore the subsequent settings Setup 1 Use the A V buttons to select a language Press the ENTER button or the GREEN button to enter the setup 2 menu Setup J S Neat Page Setup 2 Use the A V buttons to select the country of installation Press the RED button to return to setup 1 Press the ENTER button or the GREEN button to enter the setup 3 menu Sewp J Country Franco taty Perang Spain renou Payt Bieu Pape 32 EN Copyright 2013 Fast R a s Revision 04 2013 Basic controls EN Setup 3 Use the A V buttons to select the installation location Press the RED button to return to setup 2 Press the ENTER button or the GREEN button to enter the setup 4 menu Sewp 3 Auto Power Ott You TV has Seen set amp Power of after 4 heures of 1 Hout sonimuous vieweng I yuu 2 Hours wer io change Mie setting pess
11. confirm Digital Teletext Language Use the A F buttons to select the item Digital Teletext Language and then use the OK or P button to enter the submenu Use the A V buttons to select a language Then press the OK or gt button to confirm Analogue Teletext Language Use the A V buttons to select the item Analogue Teletext Language and then use the OK or P button to enter the submenu Use the A W buttons to select a language Then press the OK or P button to confirm EN 29 Copyright 2013 Fast CR a s Revision 04 2013 EN Basic controls 4 6 3 Sleep timer Use the A V buttons to select the item Sleep timer and then use the OK or button to enter the submenu Use the A V buttons to set the time Then press the OK or P button to confirm 4 6 4 Auto Power Off Use the A V buttons to select the item Auto Power Off and then use the OK or gt buttons to enter the submenu Use the A V buttons to set the time Then press the OK or button to confirm 4 7 Setup Menu Press the SETUP button to display the main menu Use the A V buttons to select Setup in the main menu then use the OK or P button to enter the menu Press A to select the desired item which you wish to adjust and enter the menu by pressing the OK or button 2 Use the lt P buttons to select an item or use the A W buttons to select another item 3 After completing setup press the SETUP button to save and return to t
12. is powered by an adapter use only the adapter and AC power cord supplied with the device Do not use faulty power sockets Check that the power plug is properly inserted into the power socket If the power plug is loose arching could result in a fire Contact a qualified electrician to have your socket replaced Only connect the device to a properly grounded socket with a protective grounding pin IF you will be installing the device on a wall or to the ceiling follow the manufacturer s instruction found in the users manual of the particular device 4EN Copyright 2013 Fast CR a s Revision 04 2013 Important safety instructions EN Repairs and maintenance e To prevent risk of injury through electric shock or the creation of a fire do not take the device out of the case there are no parts inside the case repairable or adjustable by the user without relevant equipment and qualifications Should the device require adjustment or repair contact a professional service centre e n the case of any unusual events occurring during the use of the device e g if there is a distinct smell of burning insulation or smoke comes out of the device immediately turn off the device disconnect the device from the power source and do not use the device until you have received the results of the inspection performed by the employees of the professional service centre e Have all repairs carried out by qualified personnel Repairs are n
13. the following icon will be displayed REC Press the SE button on the remote control again to set the recording time Press the EE button on the remote control again to stop recording Do you want to stop Recording After finishing recording select Yes to continue recording select No 46 EN Copyright 2013 Fast CR a s Revision 04 2013 Teletext EN 6 Teletext The majority of TV stations provide free teletext information including the latest news weather information TV programmes and stock market information etc You can only insert the teletext page based on the teletext content Displaying teletext Select a channel with a teletext signal Press the TEXT button Select the appropriate page using the coloured buttons on the remote control Press TEXT again and the TV screen will appear Selecting a page You can enter a 3 digit number to go to desired page Using the numerical buttons IF the entered number is invalid you must enter the correct 3 digit number again as soon as you finish entering the numbers You can scroll pages forwards or backwards using the PAGE buttons Mixed mode This function makes it possible to watch TV and teletext at the same time When a certain teletext page is displayed press the TEXT button again and the screen will display information about the TV and teletext at the same time Press the TEXT button again and only the TV screen will be shown
14. 0000000000 OOOOH HHOHHHHHHHHHOHHHHHOHOOO08O8O0O8OOOO8 0000000000000 OOOOOOOOHHHHHHHHHOHOOOOOO8OOOOOOOOO8 0000000000000 0888888888888F 2420000808000 80808808 0000000000000 80000808088088088 20000000 0000008080808 80888888888888 00O 0000000000000 0888888888880 vee 0000000008808 88080888888888 ee 0000000008888 8888888888S8 0000000000000 00080808088880 LAA 0000000000008 888088888888 J0 0000000000080 808088888 os DOO 0000000000000 8000800 LA 0000000000007 200 10 0 0000000000004 A 1e 0000000000006 0000000000888 ee 0000000000006 ao CAA AA 9 0000000000008 M 000000000000 0000000000080 _J 0000 OOOOOCOCL ee COOOOOOOCOSOOve O08 0000000000000 08 eed LAS 0000 OOOOOOOOOOEe 80 LAJ COOCOO OLOOOOOOOLOON 7 LA 0000000000000 0 ve 107 000000 OOOOOOOLOOLOO Add s00 0v AA 80000000 0000000000008 0000808808888G8 0000000000000 80808888888OO4 0000000000008 0880888088888C DOO 0000000000000 000080808080000 DOO 0000000000000 08000808880888 DOO 0000000000880 80808080808888888 DOO 0000000000000 80008888880888 DOO 0000000000000 000808888088 DOO 0000000000000 000888888OOE see 0000000000000 00080808808888l 00o 0000000080000 08888888880 eee 0000000000000 00080808080808 0 ae 00000000 O A 80808080 COSCO OOO 0980808080808 88808 0 SOOO 28 d 0900000000000 04 e007 3 00000000000000 __ 000 o 0000 00000008888888888888OOSOOr eee mee LLLILLLLILILLILLILLILLILILLILLLLL
15. 10 1 Photo Menu PIO see sccsceccencesuoessacacocteceavsnsnatacieiededeveroet niesdelcdeieueesuutunebbeddbendeceomsbenwoieGeaazes 54 1A Music Menu AM USIC erener Era iE Ra AA AAE EEOAE AREAREN AEON SEAN SAREES 55 10 Mave Menu Moyie h sensar S AE E EE 57 10 4 PYR NS ocrni naa aatisstensdtsonascactteeedeledunicehsatbeneshtciedbdiasnesetesaceaseieoreiensaeust 58 10 5 E Book Menu Book REAL ooccccccccccccsccsesccsesescesesessesessvscseevseevsssevsssvstsevstsetavsetevseees 59 T Care and MAINLENANCE oo ee ec ceccecceecesceccecececesecsecsecescesecsecscessvseeeacesscssetacereveetseesevevtsenseeseeats 60 e NO UM E E eee ace ale eens eee seeeees ecto ee enees 61 la We Cee SCE SING rera ein n E EEEE EGEE 62 EN 1 Copyright 2013 Fast CR a s Revision 04 2013 EN Important safety instructions Important safety conditions IF you want to use this product correctly carefully read this user s manual and store it for future reference If you give sell the device to somebody please also include all the documentation together with this device including this User s Manual To reduce the risk of injury by electrical shock do not remove the cover or the The flash symbol in rear side There are no The exclamation mark an equilateral triangle components inside which N an equilateral triangle indicates that there is the user can repair Have Symbol indicates important dangerous voltage inside atl repairs or adjustments ope
16. 4 2013 Basic controls EN and use the RED button to select Fav1 and use the GREEN button to select Fav2 and use the YELLOW button to select Fav3 Use the A V buttons to select Channe Use the A V buttons to select Channe Use the A V buttons to select Channe Use the A V buttons to select Channel and use the BLUE button to select Fav4 If the selected channel is already included in the favourites list press the RED GREEN YELLOW or BLUE button again to cancel its favourite status Press the MENU or EXIT button and the modified menu will be shown r y y 4 5 3 Country Use the OK or P button to enter the submenu then use the A V buttons to select the appropriate country of installation and confirm using the OK or P button 4 5 4 Auto Search Use the A F buttons to select the item Auto Search and then use the OK or P button to enter the submenu If the lock has been set you will be asked to enter a password O0000 Picture Sound Feature com Coe i vll 7 Retuin Use the A V buttons to select from All Digital Analogue and then use the OK or gt button to enter the submenu Are you sure Select OK and press the OK button to start the automatic search otherwise select Cancel to return to the previous page After several seconds the following screen will be shown EN 25 Copyright 2013 Fast R a s Revision 04 2013 EN Basic controls
17. K or P button to enter the submenu Record File Format Use the A V buttons to select the item Record File Format and then use the OK or button to enter the submenu Subsequently use the A V buttons to select TS or PS and confirm using the OK or P button 38 EN Copyright 2013 Fast CR a s Revision 04 2013 en ae Partition Select Use the A V buttons to select the item Partition Select and then use the OK or P button to enter the submenu The following screen will appear Tota Size G Free Sire G3 MFormat B Sat Default Partition Timer Use the A V buttons to select the item Timer and then use the OK or P button to enter the submenu The following screen will appear piem er weet Bie Bbw ai ay siv Use the amp W buttons to select Ch No Channel number the press the RED button to delete the selected channel and the following screen will appear Delete the selected timer EN 39 Copyright 2013 Fast CR a s Revision 04 2013 f Select Cancel to go back and confirm with the OK button Select OK and confirm with the OK button to delete the selected channel from the timer list Press the GREEN button to delete all timers and the following screen will appear Delete all timers Select Cancel to go back and confirm with the OK button Select OK and confirm with the OK button to delete all the timers Press the YELLOW button to add a timer
18. LILLILLLLILDS eee VW 2000 0008088888888 H8HOO8OOOOOS eee WE 9200000080008 00808088088800080800808O88O8 0000 d 0000 0080800808088 0808808888808808888 eee an 999800080008 8O00888808888080880O8OG eee 0000000000088 OOOHO88888O88O88O888O8888888 eee Dada dddaddodadododbdodbdbdbbbbabbpapbpaha bbb ddd ddd dededyeded eee 000000000000 OOOOOHHH8O8H8O8O8H888H8888O88888O8 eee 0000000000008 OOOHO8H8HHHHHHOHH8H8O8H88H888O8 eee 0000000000008 OOOOO88O88O88H8888H8H88888888O8 eee 00000000000 OOOOOHOHHHHHHHHH8H88H88O888888O8 eee 00008000080 OHOOOOHHHHOOO8OOHHO08088O888O8888 eee gJ 0000000000088 OOOO8HHOH8HH8H888H88H888888888 eee 0000000000008 OOOOO8HOHOHHHO8OHH8H8O8O88O888O8 eee 0000000000008 O8OOO88888888888H8H88888888O8 eee VW 000000000000 OOOOOOOHO8HHH8H8H88H8H8H8O88888888 eee 00080000088 HOOOOOHHHOOO8OOHHOO80808O888O8888 eee 0000000000000 OOOOH88OOH8H8O88H88H88888888888 eee 0000000000008 OOOOOHHOHHHHHHHHHH8O8H8HH88OO8 USER S MANUAL LED Television SLE ec ooo 9ee 8 ee TS C Carefully read this user s manual before putting the television into operation Keep it for future use Record the model number and the serial number of the television See the label on the rear cover and provide this information to your vendor in the event that you require repairs Contents HIV aE Sal SUE Cond VIR eagen E aE S S EAEE EA TEENER 2 t Description ore Qy saena EAE n Eae a s a P a E E A eaia eettimsetanedata 11 CEE cA a 15 TE a 1S e S
19. Photo in the main menu then press the OK button to enter Press the EXIT button to return back to the previous menu ad Caeo Press the A V button to select a file which you wish to view then in the file selection menu press the OK button or PB Il to display the image Use the OK button to select a directory and use the OK or II button to playback or to pause playback Information about the currently played file will appear for several seconds after starting or after the DISPLAY button is pressed 10 2 Music Menu Press the lt button to select Music in the main menu then press the OK button to enter Press the EXIT button to return back to the previous menu EN 55 Copyright 2013 Fast CR a s Revision 04 2013 f Press the A V button to select a file which you wish to play then in the file selection menu press the OK button or II to start playback Use the W button to return to the previous menu God is a gir mp Never grow ofd mp3 Dying in ibe sunmps Preity boy mp3 Over the rainbow mp3 Casebtance mp3 Forever mo3 a E ce ee _ N E Information about the file that is being played will appear in the left part of the menu 56 EN Copyright 2013 Fast R a s Revision 04 2013 om 10 3 Movie Menu Press the lt P button to select Movie in the main menu then press the OK button to enter Press the EXIT Button to return back to the previous menu
20. Sound Menu Press SETUP to display the main menu Use the A F buttons to select Sound and enter the menu using the OK or P button Stanew Oe f we ie ee oO z a ae Reset SUN Press A to select the desired item which you wish to adjust and enter the menu by pressing the OK or button 2 Use the lt P buttons to set the value or use the A V buttons to select another submenu And enter the menu using the OK or A button 3 After completing setup press the SETUP button to save and return to the previous menu or press the EXIT button to completely exit the menu 4 4 1 Sound Mode Use the A V buttons to select Sound Mode and enter the menu using the OK or gt button Then use the A V buttons to select a sound mode The following option are available User Standard Movie Music Speech The items Bass Treble Balance and Equaliser can only be changed in the User mode 20 EN Copyright 2013 Fast CR a s Revision 04 2013 Basic controls EN Note Repeatedly press the S MODE button on the remote control to directly change the sound mode 4 4 2 Bass Use the amp W buttons to select the option Bass then use the OK or button to enter the submenu and set the value using the lt P buttons Press the SETUP button to directly return to the previous menu 4 4 3 Balance Use the A W buttons to select the option Balance then use the OK or P button to ent
21. V DTYV Press to show information about the disc DVD mode SETUP button Press to show the OSD menu EPG button Press to show EPG Electronic Program Guide DTV mode AUDIO Serves to switch between audio languages available only if the TV program disc support this function DTV DVD modes lt A V gt buttons Used for navigating in a menu on the screen and for setting up the television according to your preferences CH LIST button Press to show a list of channels ATV DTV mode EXIT CANCEL button Serves to exit from a menu or to cancel a performed action S MODE button Press to show the audio mode VOL buttons Serve to set the volume EN 11 Revision 04 2013 EN Remote control 12 Coloured buttons Serves to perform various functions in teletext or adjusting channels in ATV DTV mode GOTO button RED Skip to a determined time location while playing a DVD CD DVD mode A B button GREEN Repeat playback of a selected segment designated by points A and B DVD mode REPEAT button YELLOW Select between various type of repeated playback DVD mode ANGLE button BLUE Select various display angles of a video DVD mode 13 RECORD LIST button Serves to open the list of recordings 14 RECORD button Serves to start recording on to a USB device DTV mode 15 INDEX button Call up a teletext content page ATV mode E Stop Serves to stop playback or recording USB DVD modes
22. angerous mains voltage and the parts accessible to the user In the case of servicing use only identical spare parts 2 EN Copyright 2013 Fast CR a s Revision 04 2013 Important safety instructions EN Installation operation e Install the device according to the instructions in the user s Manual e Leave free space on all sides of the device necessary for proper air circulation This removes the heat created during operation Covering the ventilation openings of the device s case creates a risk of overheating or damaging the device It is necessary to ensure that the ventilation openings are not blocked e g by a newspaper table cloth curtain etc Follow the installation instructions in the users manual e This device should not be located in a closed off area such as a bookshelf or rack if Sufficient ventilation is not provided for or the instructions of the manufacturer are not followed e Never insert any items into any ventilation or other openings because they could come into contact with points with dangerous voltage levels or cause a short circuit of parts which could cause a fire or injury by electric shock Never pour any liquid into the device e Do not install the device in direct sunlight or near sources of heat such as heaters heat exchangers stoves or other appliances including amplifiers producing heat High temperatures significantly reduce the lifetime of electronic components in the device
23. at the reception sensor is accessible EN 61 Copyright 2013 Fast CR a s Revision 04 2013 EN Technical specifications 13 Technical specifications a S injec SCART SCART 1 minijack USB 1366 x 768 300 nits 16 09 Dynamic contrast 1000 Response time ms 5 ms Number of colours 16 7M Adjustable colour temperature Standard Cool Warm Viewing angle 160 up down amp 170 left right 62 EN Copyright 2013 Fast CR a s Revision 04 2013 Technical specifications EN Built in tuner Video system MPEG 2MP HL H 264 Audio system MPEG 2 layer 1 2 MPEG 2 layer 2 BG DK I L a NICAM A2 STEREO sound system a O e C E E Fep O S wo ooo S w o C E Note Technical specifications may change without prior notice EN 63 Copyright 2013 Fast CR a s Revision 04 2013 INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF USED PACKAGING MATERIALS Dispose of packaging material at a public waste disposal site a CE DISPOSAL OF USED ELECTRICAL AND ELECTRONIC APPLIANCES The meaning of the symbol on the product its accessory or packaging indicates that this product shall not be treated as household waste Please dispose of this product at your applicable collection point for the recycling of electrical amp electronic equipment waste Alternatively in some states of the European Union or other European states you may retu
24. daily EPG mode IF you want to find out about programs that were broadcast in the past press the YELLOW Dutton IF you want to find out about programs that will broadcast in the future press the BLUE Dutton For more information about the broadcast program press the INFO button Press the GREEN button once to add a channel to the channel list Ly Press the GREEN button twice to add a channel to the reminder list A small reminder logo will be appear next to the program Press the EPG button again or the EXIT button to cancel the operation The channel will be marked as coded 44 EN Copyright 2013 Fast R a s Revision 04 2013 ee Le 5 7 Multi Audio Press the AUDIO button on the remote control to display the multi audio menu i Stereo t Dutch T C Use the lt P buttons to select the audio language format Press the SE button on the remote control in the DTV mode If the speed of the device is insufficient the following screen will appear Device speed not enough RECORD anyway It is necessary to change the speed of the device or select OK to continue Press the MEE button on the remote control to start recording the following screen will appear Do you want to start Recording Initialing Recorder EN 45 Copyright 2013 Fast CR a s Revision 04 2013 f Select Yes Yes to start recording The following screen will appear When recording
25. e Symptom Cause and solution Black screen power Check the power cord connection and whether the device is indicator is off turned on Check that the signal input cable is correctly connected Check that the input device is turned on Picture is flashing it is Check that the signal of the input device is compatible with Unstable the specifications of the device Check the computer output mode control panel display settings IF the settings do not correspond to the specifications of the device please adjust the settings Horizontal display frequency 30KHz 5KHz Vertical display frequency 50 Hz 75Hz Troubleshooting problems with sound and the television Symptom Cause and solution Cannot be turned on Please make sure that the power cord is connected properly Please make sure that the audio cable is connected properly Check the volume Check that there is nothing connected to the headphone jack Volume is too low Check the volume If the volume is still too low even after adjusting the volume to maximum please check that the settings on the input device are correct The picture is The input antenna is damaged or incorrectly connected Speckling The remote control is Check whether the batteries in the remote control are flat not working Whether the batteries are connected correctly Whether there are any obstacles between the remote control and the reception sensor of the device Check th
26. e chocee Off Tire 4 Hows eetiug car auc be changet n the ENU Previous Payu Bieu Pape Setup 4 Use the A V buttons to select automatic shut off Press the RED button to return to setup 3 Press the ENTER button or the GREEN button to enter the setup 5 menu Setup 4 TV Locetion Penne select where the TV will be placed The pitre Store wih be aptimized for Ital jocalion ES revout Papu Bieu Pape Setup 5 Press the RED button to return to setup 4 Press the OK button to enter the automatic search menu DTV and the following screen will appear EN 33 Copyright 2013 Fast R a s Revision 04 2013 EN Basic controls Press the SETUP button to enter the automatic search DTV and you will enter setup 6 Analogue channets fouird Digital chanel founds Setup 6 Press the RED button to return to setup 5 Press the OK button to enter the automatic search menu ATV and the following screen will appear E Pravou Page Press the SETUP button to enter the automatic search ATV and you will enter setup 6 34 EN Copyright 2013 Fast CR a s Revision 04 2013 om 9 DIV Press the DISPLAY button on the remote control to display information about channels 1 I 2 No Event info h g No Event inte 5 Cra rFroquency Kmz 22000 SancdvvicniMrz Strength EE 10 Qualily es 1 1 Number and name of the channel being watched 2 Information about th
27. e item Digital Manual Search and then use the OK or gt button to enter the submenu If the lock has been set you will be asked to enter a password 0000 T tanne Digia Manual Search AAE Soung Si erg thy ee tate Feature Quelily qr 1 Setup tana fegt Channel Use the A F buttons to select the item Channel then use the OK or button to enter the submenu and use the A W buttons to select a channel and then use the OK or gt button to confirm Start Use the A V buttons to select the item Start and then use the OK or button to enter the submenu The following channel search screen will appear after a few seconds EN 37 Copyright 2013 Fast CR a s Revision 04 2013 ee 5 2 Feature Menu Press the SETUP button to display the main menu Use the A W buttons to select Feature in the main menu then use the OK or P button to enter the menu Picture Sound Channe Feaure 1 Press A to select the desired item which you wish to adjust and enter the menu by pressing the OK or button 2 Use the lt gt buttons to select an item or use the A V buttons to select another item 3 After completing setup press the SETUP button to save and return to the previous menu or press the EXIT button to completely exit the menu 5 2 1 PVR Personal video recorder Use the A V buttons to select the item PVR Personal video recorder and then use the O
28. e program currently being broadcast 3 Current time 4 TV channel icon if it is a radio station then it will be the radio station icon 5 Start and end of broadcasting for the program being watched 6 Language icon Text icon 8 Subtitle icon g Favourite channels icon Notes The Picture Menu is the same as in the previous part of this user s manual The Sound Menu is the same as in the previous part of this user s manual The Setup Menu is the same as in the previous part of this user s manual EN 35 Copyright 2013 Fast CR a s Revision 04 2013 f 5 1 Channel Menu Press the SETUP button to display the main menu Use the A V buttons to select Channel in the main menu then use the OK or P button to enter the menu Meturmn Press A to select the desired item which you wish to adjust and enter the menu by pressing the OK or P button 2 Use the lt P buttons to select an item or use the A W buttons to select another item 3 After completing setup press the SETUP button to save and return to the previous menu or press the EXIT button to completely exit the menu 5 1 1 Channel Management Use the A F buttons to select the item Channel Management and then use the OK or gt button to enter the submenu Biw mow Sj Dhe Blew 36 EN Copyright 2013 Fast CR a s Revision 04 2013 om 5 1 2 Digital Manual Search Use the A F buttons to select th
29. ecessary if the device has been damaged in any way for example if the power cord is damaged liquid was poured on the device foreign objects have entered the device the device has been exposed to rain or moisture if the device is not working as usual or if it has fallen e inthe event of repair or replacement of a part of the device ensure that the Service technician uses components designated by the manufacturer or that these components have the same specifications as the original ones Unauthorised replacements could cause a fire lead to a danger of injury by electrical shock or other dangers e Before cleaning carrying or other maintenance disconnect the plug adapter from the power socket e Clean the device only with a dry cloth e For cleaning do not use petrol thinners or any other solvents or use any abrasive cleaning agents steel wool or any sponges with steel wool Note Do not throw the device into ordinary household waste For disposal follow all local laws and regulations Remote control and batteries e Do not expose the remote control or the batteries to direct sunlight or sources of heat such as heaters heat exchangers stoves or other appliances including amplifiers that produce heat Do not use or leave the device in the vicinity of an open fire Ensure that the sensor is not exposed to a strong light source e g sunlight or light from fluorescent light tubes which could r
30. educe the effectiveness and reliability of the remote control e Neither the remote control nor the batteries may be exposed to dripping or running water and objects filled with water must not be placed on them e g vases Protect against exposure to rain spraying or pouring of any kind of liquid Do not use outdoors Not following these instructions creates a danger of damage to the remote control or to the battery e Do not use this device near water EN 5 Copyright 2013 Fast CR a s Revision 04 2013 Important safety instructions e t is necessary to pay attention to the environmental impact aspects of battery disposal e The incorrect use of batteries may cause the leakage of the electrolyte and corrosion To ensure that the remote control works correctly proceed according to the instructions below e Do not insert the batteries in the wrong direction e Do not recharge heat open or short circuit the batteries e Do not throw batteries into a fire e Do not leave discharged batteries in the remote control e Do not combine various types of batteries or new and old batteries e If you will not be using the remote control for a long period of time remove the batteries to prevent potential damage caused by a subsequent battery leakage e f the remote control is not working correctly or its operating range is reduced change all batteries for new ones e f electrolyte leaks out from the batte
31. er the submenu and set the value using the lt P buttons Press the SETUP button to directly return to the previous menu 4 4 4 Treble Use the A F buttons to select the option Treble then use the OK or P button to enter the submenu and set the value using the lt P buttons Press the SETUP button to directly return to the previous menu 4 4 5 EQ Use the A V buttons to select the option EQ then use the OK or button to enter the submenu and using the lt P buttons select fram the equaliser modes EQIOQHZ EQ300HZ EQIKHZ EQ3KHZ EQ8KHZ Then use the OK or button to enter the submenu and select the value using the lt P gt buttons Then press the SETUP button to directly return to the previous menu 4 4 6 Surround Surround sound Use the A F buttons to select the option Surround then use the OK or P button to enter the submenu and using the lt P buttons select On or Off 4 4 7 AVL Automatic volume limiter Use the A V buttons to select the option AVL Automatic volume limiter then use the OK or P button to enter the submenu and using the lt P buttons select On or Off 4 4 8 Reset Use the A V buttons to select the option Reset then enter the menu using the OK button or use the button to confirm and then select OK to reset the values EN 21 Copyright 2013 Fast CR a s Revision 04 2013 EN Basic controls 4 5 Channel Menu Press SETUP to display the main menu Use the A W butt
32. eries gradually reduces the remote control range There must be no solid obstacles in the area between the remote control and the device when the remote control is being used During standard use the lifetime of batteries in the remote control is about 1 Year When the effective range of the remote control is substantially reduced or when there are problems with its use change both the batteries in the remote control If YOU will not be Using the remote control for a longer period of time take out both batteries in this way you will prevent potential damage caused by their leakage Prevent strong light from falling on the device e g sunlight or strong fluorescent lamps or ecological light bulbs which could reduce the effectiveness and reliability of the infrared remote control Battery Installation Remove the battery compartment cover Insert two type SUM 4 AAA batteries as shown on the picture below Ensure that the batteries have the correct polarity when inserting them Return the cover back to its place Z5 14 EN Copyright 2013 Fast R a s Revision 04 2013 Before using EN 3 Before using 3 1 Installation of a TV stand
33. he lt P buttons to switch between favourites groups 1 2 3 and 4 5 5 Subtitle Press the SUBTITLE button on the remote control to display the subtitles menu and the following screens 4 DTV Subtitle gt av Enter Use the lt P buttons to select Off confirm using the OK button and the subtitles will not be displayed Use the A V buttons to select ENG confirm using the OK button and the subtitles will be displayed in English Press the EXIT button to exit the menu EN 43 Copyright 2013 Fast CR a s Revision 04 2013 f 5 6 EPG Electronic Program Guide Press the EPG button on the remote control to display the daily mode of the EPG menu 1 lt o7rr2008 SB 2 ONiIZAGOS OS tS O7 1252005 10 03 Sycdinen asiak Likainen Len Mike ult anko mantyO Aeet Luotemalia piteyiii itk titiis SG ieia bunj Se seata Oavalin Houseman verha Slereg ie We We Event ini YLE TY ho Eveni ip f Pt ea amp gt m vYLera No Event into ina Neo Given Info vie theme No Eveni into E ULIT E E nan Day mco BB emee 1 Number and name of the channel being watched 2 Start and end of the program currently being watched and the name of the broadcast program 3 Current date and time Use the A V buttons to select a channel or program You can use the lt P gt buttons to switch between channels and programs You can use the RED button to switch between the weekly EPG mode and the
34. he following Press the button on the remote control to turn on the power to the television its LED indicator will be lit green Now you can use the many functions of your new television 4 2 Selecting an input source Press the SOURCE button to show the input source list Use the A V buttons to select the desired input source Press the OK button or B to confirm the input source Note The grey items shown on pictures here may not be activate for a given model or are explained in a different part of this user s manual Press the SETUP button to show the main OSD menu Use the A V buttons to select the desired menu Press the OK or button to enter the submenu Use the lt button to return back to the previous menu Use the A W buttons to select an option and then press the OK button or to enter the submenu use the lt P buttons to set a value or the A W buttons to select a submenu Press the SETUP button to save and return back to the previous menu and press the EXIT button to completely exit the menu Press the DISPLAY button on the remote control to display information about the broadcast channel gt Current source Current channel number NICAM mode of the current channel The audio system of the current channel can be changed in the manual analogue Search Menu LNs EN 17 Copyright 2013 Fast CR a s Revision 04 2013 EN Basic controls 4 3 Picture Menu Press SETUP t
35. he previous menu or press the EXIT button to completely exit the menu 4 7 1 OSD Timer Use the A V buttons to select the item OSD Timer and then use the OK or P button to enter the submenu Use the A V buttons to set the time 5 seconds 10 seconds 15 seconds 20 seconds 25 seconds 30 seconds never Then press the OK or P button to confirm 30 EN Copyright 2013 Fast CR a s Revision 04 2013 Basic controls EN 4 7 2 Auto SCART Use the A V buttons to select the item Auto SCART and then use the OK or P buttons to enter the submenu Use the button to select On On or Off Off Then press the OK or B button to confirm 4 7 3 PC Setup Use the A F buttons to select the item PC Setup and then use the OK or gt buttons to enter the submenu Use the button to enter Then press the OK or button to confirm if the PC signal is available 4 7 4 HDMI Mode Use the A W buttons to select the item HDMI Mode and then use the OK or buttons to enter the submenu Use the button to select fram Auto PC Video Then press the OK or P button to confirm if the PC signal is available 4 7 5 Blue Screen Use the A V buttons to select the item Blue Screen and then use the OK or P buttons to enter the submenu Use the A V buttons to select On or Off Then press the OK or gt button to confirm 4 7 6 Reset TV Setting Use the A F buttons to select the item Reset TV Setting and then use the OK or gt
36. he submenu Use the A F buttons to choose from BG DK I L L and the use the OK or button to confirm 4 6 Feature Menu Press the SETUP button to display the main menu Use the A V buttons to select Feature in the main menu then use the OK or button to enter the menu 1 Press A F to select the desired item which you wish to adjust and enter the menu by pressing the OK or P button 2 Use the lt buttons to select an item or use the A V buttons to select another item 3 After completing setup press the SETUP button to save and return to the previous menu or press the EXIT button to completely exit the menu EN 27 Copyright 2013 Fast CR a s Revision 04 2013 EN Basic controls 28 EN 4 6 1 Child Lock Use the A V buttons to select the item Child lock and then use the OK or P button to enter the submenu Enter the default password OO00 CHIA Lock Paroma Loce Hehinn Keypad Lock Use the A V buttons to select the item Keypad lock and then use the OK or P button to enter the submenu Use the A V buttons to select On or Off Enter the default password 0000 Then press the OK or button to confirm Parental Lock Use the A V buttons to select the item Parental lock and then use the OK or gt button to enter the submenu Use the A W buttons to select a rating from 4 18 or Off Then press the OK or gt button to confirm Change Pin Code Use the A F buttons to
37. his device supports the MP3 MPEG1 MPEG2 AVI JPEG and BMP formats This device supports the FAT16 FAT32 and NTFS formats MTP Media Transfer Protocol is not supported Connect the device directly into the USB port on your television IF you are using an extension cable compatibility problems may arise Before connecting a device to the television back up your files to prevent damage or loss of data The manufacturer takes no responsibility for data loss or damage Do not disconnect the USB device while it is loading IF you wish to change the playback mode you first need to exit from the current playback mode by pressing the EXIT button The higher the resolution of the picture the longer it will take to display on the screen In the case of unsupported or damaged files the message Unsupported format Will appear EN 53 Copyright 2013 Fast CR a s Revision 04 2013 Lap USB multimedia playback format File extension Xvid MPEG 4 MP3 WMA AAC at MPEG H 264 ee ee bs peg Progressive JPEG Basic JPEG aa ee Oooo o o oed O Note Before entering the MEDIA menu connect the USB device then press the SOURCE button to setup the input USB source Press the A V button to select USB in the Source menu then press the OK or P button to enter 10 1 Photo Menu 54 EN Copyright 2013 Fast CR a s Revision 04 2013 om Press the lt P button to select
38. in Your power socket corresponds to the voltage on the rating label of the device or on its power adapter If you are not certain about the type of the power sources in your home contact your vendor or the local energy company e Before turning on the device check that the electrical connection is performed properly and in accordance with the instructions of the manufacturer Before connecting or changing the connection turn off the device and disconnect it from the mains e Remember to always disconnect the power plug adapter from the power socket before disconnecting the power cable from the rear side of the device EN 3 Copyright 2013 Fast CR a s Revision 04 2013 Important safety instructions e Insert the power plug into a Separate power socket Do not overload wall sockets with extension cords or multi socket adapters There is a risk of injury by electric shock e When disconnecting hold the power cord by the plug and not by the cord itself e Disconnect the device from the power socket during storms or if you will not be Using it for an extended period of time e Avoid moving the device from a cold environment to a warm one or vice versa or when using the device in a very humid environment Air humidity may condense on Some components inside the case of the device and the device may stop working temporarily If this occurs leave the device in a warm and well ventilated place and wait 1 2 hou
39. move it to a new position and pres the OK or Blue button This will confirm the move to the new position If the delete channel logo appears press the SETUP or OK button and the following menu will appear Do You Want to delete the Selected items Use the W button to select OK use the to select cancel use the OK button to confirm Successfully updated Use the A V buttons to select a channel then press the OK button to enter the rename channel menu EN 23 Copyright 2013 Fast CR a s Revision 04 2013 EN Basic controls Press the RED button to insert a space Press the GREEN button to change the mode Use the A V or lt P gt buttons to select a character and confirm using the OK button Press the YELLOW button to delete a character Press the BLUE button to save the changes and to return to the previous page Press the EXIT button and the following screen will appear Please confirm saving To completely exit the menu select Cancel but the changes will not be saved To successfully save select OK and the following screen will appear informing you about the successful save Save successful 4 5 2 Favorite Manager Use the A V buttons to select the item Favorite Manager and then use the OK or button to enter the submenu Mo Program Marne Pay sir Tava Fave l e e LEFT Breil meet rave 24 EN Copyright 2013 Fast CR a s Revision 0
40. o display the main menu Use the A V buttons to select Picture and enter the menu using the OK or button Press A F to select the desired item which you wish to adjust and enter the menu by pressing the OK or P button 2 Use the lt P buttons to set the value or use the A V buttons to select another submenu And enter the menu using the OK or P button 3 After completing setup press the SETUP button to save and return to the previous menu or press the EXIT button to completely exit the menu 4 1 3 Picture Mode Use the A F buttons to select the item Picture Mode and enter the menu using the OK or gt button and select a mode using the lt P buttons In the menu there are the following modes User Standard Vivid Soft Optimal 18 EN Copyright 2013 Fast CR a s Revision 04 2013 Basic controls EN The items Brightness Contrast Sharpness Color can only be changed in the User mode Note Repeatedly press the P MODE button on the remote control to directly change the picture mode 4 2 3 Brightness Use the A V buttons to select the option Brightness then enter the menu using the OK or button and perform the settings using the lt P gt buttons Press the SETUP button to directly return to the previous menu 4 3 3 Contrast Use the A F buttons to select the option Contrast then enter the menu using the OK or button and perform the settings using the lt P gt butt
41. ode if the signal is not renewed within 15 minutes 48 EN Copyright 2013 Fast CR a s Revision 04 2013 oe 8 HDMI 8 1 Setup Menu Press the SETUP button to display the main menu Use the A V buttons to select Setup in the main menu then use the OK or P button to enter the menu Apl 1 Press A to select the desired item which you wish to adjust and enter the menu by pressing the OK or P button 2 Use the lt buttons to select an item or use the A V buttons to select another item 3 After completing setup press the SETUP button to save and return to the previous menu or press the EXIT button to completely exit the menu 8 2 HDMI Setup Use the A V buttons to select the item HDMI Setup and then use the OK or P button to enter the submenu EN 49 Copyright 2013 Fast CR a s Revision 04 2013 EN SCART AV COMPONENT Settings Menu Note Other menus and descriptions are the same as in the preceding part of this users Manual The HDMI source menu is not available if the items are grey The Picture Menu is the same as in the previous part of this user s manual The Sound Menu is the same as in the previous part of this user s manual The Feature Menu is the same as in the previous part of this user s manual 50 EN Copyright 2013 Fast CR a s Revision 04 2013 ee e 9 PC 9 1 Setup Menu Press the SETUP button to display the main menu U
42. ons Press the SETUP button to directly return to the previous menu 4 3 4 Sharpness Use the A V buttons to select the option Sharpness then enter the menu using the OK or button and perform the settings using the lt P buttons Press the SETUP button to directly return to the previous menu 4 3 5 Colour Use the A V buttons to select the option Colour then enter the menu using the OK or gt button and perform the settings using the lt B buttons Press the SETUP button to directly return to the previous menu 4 3 6 Tint Use the A V buttons to select the option Tint then enter the menu using the OK or gt button and perform the settings using the lt P buttons Press the SETUP button to directly return to the previous menu 4 3 7 Colour Temperature Use the A V buttons to select the option Colour Temperature then enter the menu using the OK or P button and then using the lt P buttons select between Standard Cool or Warm EN 19 Copyright 2013 Fast CR a s Revision 04 2013 EN Basic controls 4 3 8 Noise Reduction Use the A F buttons to select the option Noise Reduction then enter the menu using the OK or button and then using the lt P buttons select between Off Low Middle or High 4 3 9 Reset Use the A W buttons to select the option Reset then enter the menu using the OK button or use the button to confirm and then select OK to reset the values 4 4
43. ons to select Channel and enter the menu using the OK or P button Channel Patil Digia Manus Search Channel Feature LCN Omatt Setup fieira 1 Press A to select the desired item which you wish to adjust and enter the menu by pressing the OK or button 2 Use the A F buttons to select an item and enter the submenu using the OK or P button 3 After completing setup press the SETUP button to save and return to the previous menu or press the EXIT button to completely exit the menu 4 1 5 Channel Management Use the A V buttons to select the item Channel Management and then use the OK or gt button to enter the submenu min Ble Si Ship Siow Press the RED button to set a lock for the current channel if a lock is already set for the current channel press the button again to deactivate the lock 22 EN Copyright 2013 Fast CR a s Revision 04 2013 Basic controls EN Press the GREEN button to delete the current channel if the current channel is already deleted press this button again to cancel the deletion Press the YELLOW button to set skip for the current channel if a skip is already set for the current channel press the button again to deactivate the skip Press the BLUE button to move a channel IF any of the channels was incorrectly located in the list you can move it to the existing position using the A V buttons Select a channel that you wish to move Press the BLUE button and
44. rating or servicing this device which presents performed at an authorised Instructions in the a risk of injury By electrical service centre device s documentation shock General safety instructions Carefully read this manual before using the device Follow the instructions contained in this user s manual Heed all warnings Adhere to all instructions Use only accessories determined by the manufacturer AN OPEN FLAME MUST NOT BE PLACED ON THE DEVICE E G A BURNING CANDLE DO NOT PLACE HOT ITEMS OR OBJECTS WITH AN OPEN FLAME E G CANDLES OR NIGHT LAMPS ON ORIN THE VICINITY OF THE DEVICE HIGH TEMPERATURES MAY MELT PLASTIC PARTS AND CAUSE A FIRE e Use the device in a temperate climate zone e Neither the manufacturer nor the vendor of the device under any condition Lakes responsibility for any direct or indirect damages caused by not adhering to instructions for installation set up use servicing or cleaning of this device as described in this user s manual e Protect the device against being knocked dropped nit shaken and against vibrations humidity and dust e Before allowing children to use the device they must be appropriately to their age informed about the correct and safe use of the player e f the device is equipped with a headphone jack do not use headphones set to an extreme volume There is a danger of hearing damage or loss This symbol indicates that the device has double insulation between the d
45. ries have the remote control cleaned at an authorised service centre A ATTENTION To preventa fire hazard or injury by electrical shock do not expose this device to rain or humidity Batteries must not be exposed to excessive heat for example sunlight fire etc 6 EN Copyright 2013 Fast R a s Revision 04 2013 Important safety instructions EN SE NI CO R Supplement to the LCD TV user s manual Measures to take when a static image is displayed red blue green pixels on the screen A static image can permanently damage the display part of the television Do not leave a static image on an LCD screen for longer than 2 hours because this could damage the screen This tupe of damage is known as screen burn in Similar damage to the LCD screen can be caused by a statically located TV channel logo Watching television in 4 3 16 9 formats or similar formats not covering the entire area of the screen for a long time may leave marks on the right or left side or possibly in the middle of the picture as a result of the differences in light emission Similar damage may also occur when watching a DVD or playing games The display of a static image from video games or computers for an extended period of time may cause a partial effect of a persistent image To prevent this effect fram occurring lower the brightness and contrast when displaying a static picture Damage to the screen resulting from the abo
46. rn your products to your local retailer when buying an equivalent new product The correct disposal of this product will help save valuable natural resources and help in preventing the potential negative impact on the environment and human health which could be caused as a result of improper liquidation of waste Please ask your local authorities or the nearest waste collection centre for further details The improper disposal of this type of waste may fall subject to national regulations for fines For business entities in the European Union IF you wish to dispose of an electrical or electronic device request the necessary information from your seller or supplier Disposal in other countries outside the European Union IF you wish to dispose of this product request the necessary information about the correct disposal method from local government departments or from your Seller This product meets all the basic EU regulation requirements that relate to it Changes to the text design and technical specifications may occur without prior notice and we reserve the right to make these changes 64 EN Copyright 2013 Fast CR a s Revision 04 2013 SENCOR EN Warranty conditions Warranty card is not a part of the device packaging This product is warranted for the period of 24 months from the date of purchase to the end user Warranty is limited to the following conditions Warranty is referred only to the customer goods u
47. rs until the moisture evaporates and the device can once more be used as usual Take care especially during the first use of the player immediately after its purchase during a cold season e Do not place this device on an unstable cart pedestal stand bracket or table The device could fall and cause serious injuries to children or adults or could be Seriously damaged or damage other items Only use the device with a cart pedestal Stand or table designated by the manufacturer or sold with the device Any mounting of the device should be carried out according to the manufacturer s instructions and the mounting accessories recommended by the manufacturer should be used e Do not lean on the device do not lean over it or Use it as a step Protect it against Violent movements Ensure that children do not play with the device e If using the cart be careful when moving it Stopping suddenly excessive force and Uneven surfaces could cause the cart to fall over with the device e Neither the manufacturer nor the vendor of the device under any condition takes responsibility for any direct or indirect damages caused by not adhering to instructions for installation setup use repair or cleaning of this device as described in this user s manual e Protect the device against being knocked dropped hit shaken and against vibrations humidity and dust e Do not expose the device to extreme temperatures or humid conditions Note If the device
48. s lit red in the stand by mode and lit green during normal operation 3 Mains power switch Television control panel 1 2 3 4 5 6 7 SOURCE MENU CH CH VOL VOL D 3 4 7 CH CH D SOURCE button Select a input source MENU button Enter a menu or exit it CH button Previous channel number CH button Next channel number VOL button Reduce the volume VOL button Increase the volume 5 button Switch between the Stand by and the On mode Nou kau EN 9 Copyright 2013 Fast CR a s Revision 04 2013 EN Description of the device Side panel 1 Audio Earphone output 1 2 TV signal input 3 Cl Slot 4 AV input 2 3 4 MN 1 12V DC power input 2 USB connector 3 HDMI input 4 PC VGA input 5 PC Audio input 6 SCART connector 7 Component input 10 EN Copyright 2013 Fast CR a s Revision 04 2013 OO AONO e600 2 Remote control A i Copyright 2013 Fast CR 10 11 Remote control EN 5 button Turns the television on from the stand by mode Numerical buttons 0 9 Press O 9 to directly select a TV channel in ATV and DIV mode In the DIV mode it serves to select numerical items in a menu DISPLAY button Press to display information about the current channel such as the current time and the name of the channel AT
49. s the operation will be stopped Unexpected behaviour of the connected memory device or the presence of viruses or other damaging software may cause the functions of the device to stop working necessitating a restart The USB connector is the standard type and is not able to power a USB device with a high power usage e g hard disk drives HDD Use devices with independent power Supplies and power them from their own power supplies The device was designed to achieve maximum compatibility with memory devices With respect to the variety of devices on the market it is not possible to guarantee compatibility with every USB device In the event of difficulties try formatting the memory device directly in the device If problems persist use a different memory device Due to the wide range of SD MMC MS cards USB devices available on the market it is not possible to guarantee the compatibility of the device with all SD MMC MS cards USB devices Serial number of the device The serial number of the device is Unigue and Uneguivocally identifies your device Enter the serial number of your device together with other details necessary for the definite identification of your device below Serial number Date of purchase 8 EN Copyright 2013 Fast CR a s Revision 04 2013 Description of the device EN 1 Description of the device Front panel 1 2 ST E CY 1 Remote control sensor 2 Indicator it i
50. se the A V buttons to select Setup in the main menu then use the OK or P button to enter the menu Press A F to select the desired item which you wish to adjust and enter the menu by pressing the OK or button 2 Use the lt buttons to select an item or Use the A V buttons to select another item 3 After completing setup press the SETUP button to save and return to the previous menu or press the EXIT button to completely exit the menu 9 2 PC Setup Use the A V buttons to select the item PC Setup and then use the OK or gt button to enter the submenu EN 51 Copyright 2013 Fast CR a s Revision 04 2013 B Auto Adjust Use the A W buttons to select the item Auto Adjust and then use the OK or button to enter the submenu Adjusting Please Wait H Position Use the A F buttons to select the item H Position and then use the OK or button to enter the submenu Use the lt P gt buttons to adjust the horizontal position of the picture V Position Use the A V buttons to select the item V Position and then use the OK or P button to enter the submenu Use the lt P gt buttons to adjust the vertical position of the picture Phase Use the A F buttons to select the item Phase and then use the OK or P button to enter the submenu Use the lt gt buttons to set the phase of the screen Clock Use the A V buttons to select the item Clock and then use the OK or button to enter the
51. select a file which you wish to play then in the file selection menu press the OK button or II to start playback EN 59 Copyright 2013 Fast CR a s Revision 04 2013 EN Care and maintenance 11 Care and maintenance Premature malfunction can be prevented Careful and regular cleaning can extend the lifetime of your new television Before starting to clean do not forget to turn off the television and to pull the power cord out of the power socket Cleaning the screen Remove dust from the screen in the following manner Dampen a fine wiping cloth in lukewarm water containing an washing detergent for textiles or a dishwashing detergent Wring the wiping cloth until it is almost dry and use it to clean the screen 2 Make sure that the screen is not wet and allow it to dry naturally before turning it on Cleaning other parts To clean dirt or dust wipe the other parts of the television with a fine dry lint free wiping cloth Do not use a damp wiping cloth Taking out of operation for an extended period IF you will not be using the television for an extended period of time e g during a holiday it is advisable to pull the power cord out of the power socket to prevent the television fram being damaged as a result of a lightning strike or current spike 60 EN Copyright 2013 Fast CR a s Revision 04 2013 Troubleshooting EN 12 Troubleshooting Troubleshooting problems with the pictur
52. select the item Change Pin Code then use the OK or P buttons to enter the menu and in the change pin code menu the following screen will appear Rehinn Copyright 2013 Fast CR a s Revision 04 2013 Basic controls EN Into the field Old Password enter the old password If the password is incorrect you will not be able to change the password Into the field New password enter the new password Into the field Confirm New Password enter the new password again If both the new passwords are entered correctly a screen will appear with a message about the new password being successfully saved otherwise the system will display a message that the passwords were entered incorrectly 4 6 2 Language Use the A F buttons to select the item Language and then press the OK or button to enter the submenu e O80 Language Pretarea Guoune L Enn D Picture E Preferred Audio E oz Digit Tewext Language Toy Analog Teintes ianguaye TS Channel Setup u MAIU OSD Language Use the amp W buttons to select the item OSD Language and then use the OK or P button to enter the submenu Use the A V buttons to select a language Then press the OK or gt button to confirm Preferred Subtitle Use the A W buttons to select the item Preferred Subtitle and then use the OK or gt button to enter the submenu Use the A V buttons to select a language Then press the OK or P button to
53. sing for common domestic use The claim for service can be applied either at dealer s shop where the product was bought or at below mentioned authorized Service shops The end user is obligated to set up a claim immediately when the defects appeared but only till the end of warranty period The end user is obligated to cooperate to certify the claiming defects Only completed and clean according to hygienic standards product will be accepted In case of eligible warranty claim the warranty period will be prolonged by the period from the date of claim application till the date of taking over the product by end user or the date the end user is obligated to take it over To obtain the service under this warranty end user is obligated to certify his claim with duly completed following documents receipt certificate of warranty certificate of installation F This warranty is void especially if apply as follows Defects which were put on sale Wear out or damage caused by common use The product was damaged by unprofessional or wrong installation used in contrary to the applicable instruction manual used in contrary to legal enactment and common process of use or used for another purpose which has been designed for The product was damaged by uncared for or insufficient maintenance The product was damaged b
54. submenu Use the lt gt buttons to set the clock Note Other menus and descriptions are the same as in the preceding part of this Users manual Ihe PC source menu is not available if the items are grey The Picture Menu is the same as in the previous part of this user s manual The Sound Menu is the same as in the previous part of this user s manual The Feature Menu is the same as in the previous part of this user s manual 52 EN Copyright 2013 Fast CR a s Revision 04 2013 om 10 USB devices Brief introduction This device has a USB 2 0 interface and can therefore playback music movies or images from USB devices USB is an abbreviation of Universal Serial Bus The majority of USB devices available on the market are either USB 1 1 or USB 2 0 Here we list several types of USB 1 1 devices Monitor communication devices sound devices Human Input Devices HID high capacity memories the majority of flash disks USB HDD etc are high capacity memory devices High capacity memory devices enable 2 types of transmission formats 1 2 USB 1 1 Mass Storage Class Control Bulk Interrupt CBI USB 1 1 Mass Storage Class Bulk Only Transport This device only supports USB 1 1 Mass Storage Class Bulk Only Transport we are not certain whether different USB devices will be supported For this reason please first find out the characteristics of the USB device before using it Note i 2 3 4 T
55. to the list and the following screen will appear Recorder if the PVR function is supported Use the A V buttons to select Recorder then use the OK or button to enter the submenu and use the A V buttons to select Recorder Recorder or Reminder Reminder Press the SETUP button to save the settings and press the EXIT button to exit the menu Use the A F buttons to select a channel that you wish to edit Press the BLUE button and the timer edit menu will appear Type Use the A V buttons to select the option Type then use the OK or button to enter the submenu and using the A V buttons select DTV or radio Program Use the A V buttons to select Channel then use the OK or button to enter the submenu and use the A V buttons to select the channel that you wish to add to the timer list 40 EN Copyright 2013 Fast CR a s Revision 04 2013 om Start Time Use the A V buttons to select Start Time then use the OK or P buttons to enter the submenu and Use the numerical buttons to enter the start time Duration Use the A V buttons to select Duration then use the OK button to enter the submenu and use the numerical buttons to enter the duration Date Use the A V buttons to select Date then use the OK button to enter the submenu and use the numerical buttons to enter the date Mode Use the A V buttons to select Mode then use the OK or P button to enter the submenu and use the A V buttons to select Once
56. ve mentioned causes is not covered by the warranty SEAD UA ace pixels may appear on the screen This is a characteristic feature of liquid crystal displays and does not represent a problem LCD screens are manufactured using a very precise technology in order to achieve a very fine picture resolution From time to time several inactive pixels may appear on the screen as a permanently red blue green or black pixel up to 0 001 of the total number of pixels on the screen This does not in any way affect the features and performance of your television EN 7 Copyright 2013 Fast CR a s Revision 04 2013 EN Important safety instructions Notes on the USB connector USB memory devices must be inserted into the device directly To prevent data transmission failure or its interference do not use USB extension cables Electrostatic discharges may cause the device to malfunction In such an event the user must restart the device Before using a USB memory device test its ability to communicate with the device and its data reading and writing speed To achieve maximum reading speed we recommend that you keep disk space defragmented Use the FAT 32 file system a single partition without protection If reading and writing on the USB memory device is not continuous undesirable effects may occur such as partial image loss distortions checkering effects or complete image loss audio defects and in extreme case
57. y dirt accident of force majeure natural disaster fire and flood Defects on functionality caused by low duality of signal electromagnetic field interference etc The product was mechanically damaged e g broken button fall Damage caused by use of unsuitable media fillings expendable supplies batteries or by unsuitable working Uakes conditions e g high temperatures high humidity q Repair modification or other failure action to the pr End user did not prove enough his right to claim time and place of purchase Data on presented documents differs from data on products Cases when the claiming product cannot be indentified according to the presented documents e g the serial number or the warranty seal has been damaged OC oduct by unauthorized person gt Authorized service centers Visit www sencor eu for detailed information about authorized service centers EN 65 Copyright 2013 Fast CR a s Revision 04 2013 66 EN Copyright 2013 Fast CR a s Revision 04 2013

Download Pdf Manuals

image

Related Search

Related Contents

「ガソリン携行缶の正しい使い方」(PDF:377KB)  conga-BM45 User's Guide  PowerSeries Neo Controlador de alarma  Eiki LC-X7L CRT Television User Manual  "user manual"  安全上のご注意  Sony VAIO VPCEA3AFX    Xerox WorkCentre 7425_A  Notice  

Copyright © All rights reserved.
Failed to retrieve file