Da-Lite 89754L projection screen
Contents
1. Case Cover Figure 4 Screw Hook O He Rotate Up Figure 5 Troubleshooting Symptom Cause Solution Screen will not operate Motor does not hum Incorrect line voltage Blown fuse Tripped circuit breaker No power to operating switch or junction Power at junction box Thermal overload tripped Verify 115125V or 220 240V If insufficient voltage rewire Reset circuit improper co Up Position incoming electric line Replace fuse breaker nnections Down Position Check for power across black and white leads Check above Tighten all loose wire connections Correct any Check for power across red and white leads Let motor cool down fo 15 minutes Try again Broken wire in the down or up position Check for continuity Cut off old splice and reconnect Defective motor limit switch or capacitor Replace motor assembly NOTE Motor is a sealed assembly Capacitor burned out Replace motor assembly Lost roller wrap See instructions below Incorrect stopping position in downward direction Down limit switch out of adjustment See installation instructions Lost roller wrap See instructions below Incorrect stopping position in upward direction Up limit switch out of adjustment Adjust up limit switch Call for information Noise NOTE Screen will operate Gear noise Replace motor assembly2. INSTRUCTION BOOK FOR Designer Contour Electrol DA LITE Important Safety Instructions When using your video equipment basic safety precautions should always be followed including the following 1 2 Position the cord so that it will not be tri contact hot surfaces Read and understand all instructions before using pped over pulled or f an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons Save These Instruction s Installation Carefully unpack screen and remove outer wrapping from case Remove the black tape from the slat bar after the case h There aret as been installed hree ways to install the Designer Contour Electrol Wall Mount Ceiling Mount or Ceiling Hook Procedures for each method are as follows Wall Mount 1 Secure the wall mount bracket to the wall at the desired height Bracket should be fastened to wall studs or some reinforcement within the wall Concrete or brick walls r
3. with a low pitched hum Coasting Defective brake Replace motor assembly Restoring Lost Roller Wrap 1 2 3 4 Tape a strap to the bottom of the screen surface Push strap over back of roller Feed fabric as you pull strap to draw fabric over top of roller Remove tape and strap LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da Lite branded products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay
4. cover must be removed to access the motor limit switches Remove the case cover screw from both ends of the screen See figure 4 Be sure to hold the cover while removing the screws Rotate the cover up and away from the case until it can be removed SETTING THE DOWN LIMIT POSITION To Reduce Screen Drop Turn the red limit switch screw clockwise to decrease the amount of screen drop Run the screen down to test the stop position If the screen drops too far raise the screen about one foot and adjust the limit switch again Repeat until the desired position is set To Increase Screen Drop Turn the red limit switch screw counterclockwise to increase the amount of screen drop Run the screen down to test the stop position If the screen does not drop enough raise the screen about one foot and adjust the limit switch again Repeat until the desired position is set A CAUTION Do not adjust for more drop than what was ordered At least 1 1 2 wraps of fabric must remain on the roller This screen comes standard with 0 or 2 black at top See the specification data sheet for details A ATTENTION N effectuez pas de r glage pour obtenir un d roulement sup rieur a celui command Au moins 1 1 2 tour de toile doit tre maintenu sur le cylindre Cet cran est dot de s rie d une bande noire sup rieure de O cm O po ou 5 cm 2 po Consultez la fiche technique pour plus de renseignements
5. end cap on the right end of the case and insert the brackets into the case channel Lock the brackets in place by tightening two set screws Refer to figure 3 The brackets can be attached anywhere within 12 of the end of the case Attach an S hook or similar fastener to the large center hole on the bracket 4 Case Hook he a Ae 4 Wall Mount Bracket O Stop Screw Figure 1 Set Screws 2 Ceiling Mount Holes Endcap Screws 3 Endcap Set Screws 2 Hook Mount Hole Endcap Screws 3 Endcap Figure 3 Electrical Installation Internal wiring has been completed at the factory Installer must route power to the wall switch and to the junction box located on the left end of the screen case Standard installation is for a single 120VAC or 240VAC wall switch to control the screen Optional Control units may have been ordered Wiring diagrams for the built in VPI and low voltage control are included in these instructions Refer to additional instructions for the external VPI external low voltage control SCB 100 and SCB 200 Refer to the appropriate wiring diagram for your screen 120V Wiring Diagram For Standard Wall Switch Junction Box Located In Left Endcap Ground To Case Ground Must Be Connected To Building Ground Black Down Red Up SPDT Switch with Center Off AC Common AC HOT 120VAC
6. 60HZ 1 AMP Black Yellow Down This Switch Can Not NOTE A single switch cannot be used to operate more be used with LVC than one screen Contact the factory for further information 240V Wiring Diagram For Standard Wall Switch Junction Box Located In Left Endcap Ground To Case Ground Must Be Connected To Building Ground Rear or DPDT Switch with Center Off Brown and Yellow AC HOT 220 240 VAC 50HZ 2 AMP BLUE JUMPER Blue AC Common Down J Q WIRE Black NOTE A single switch cannot be used to operate more This Switch Can Not i A be used with LVC than one screen Contact the factory for further information Electrical Installation 120V Wiring Diagram With Optional Built In Low Voltage Control Red White Common i LLL VALL LELET White Common Black Hot 120VAC 60HZ Low Voltage Wall Switch Ground Must Optional RF or IR Remote Be Connected ad To Building Ground 240V Wiring Diagram With Optional Built In Low Voltage Control Optional RF or IR Remote Connector Blue Common 240VAC 50HZ Low Voltage Brown Hot Wall Switch Ground Must Be Connected To Building Ground Screen Adjustment Screen travel is stopped automatically in the down and up positions by the limit switches that are preset at the factory If it s necessary to adjust for more or less drop follow the steps below The case
7. all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 800 622 3737 F 574 267 7804 or 877 325 4832 E info da lite com www da lite com DL 0177 Rev 2 09 14 2014 Milestone AV Technologies LLC Printed in U S A 89697
8. eguire special fasteners and anchors Make sure the bracket is level See figure 1 for reference dimensions Keep in mind you will need at least 5 8 between the ceiling and the top of the wall mount bracket to be able to position the case on the bracket Mount the screen case on the wall bracket as shown in figure 1 Be sure the case is fully seated on the bracket Tighten the stop screws against the wall bracket Ceiling Mount 1 Do not remove the wall mount bracket even if you are not using it for mounting This provides structural stability to the case Be sure the ceiling has adequate reinforcement to attach the screen brackets The top of the screen case has a channel that the ceiling mount brackets slide into Remove the end cap on the right end of the case and insert the brackets into the case channel Lock the brackets in place by tightening two set screws Refer to figure 2 Mount cannot be more than 12 from end of case Hold the screen case up to the ceiling and mark the hole ocations Drill holes into the ceiling and attach screen with the appropriate fasteners for your ceiling Ceiling Hook 1 Do not remove the wall mount bracket even if you are not using it for mounting This provides structural stability to the case Be sure the ceiling has adequate reinforcement to attach a hook anchor The top of the screen case has a channel that the ceiling hook brackets slide into Remove the
Download Pdf Manuals
Related Search