Siemens WM14Y891GB washing machine
Contents
1. Clamp mains cable on the holders Insert and tighten the bolts Before switching on the appliance Always remove the transportation protection devices Page 56 To prevent unused detergent from flowing into the outlet during the next wash cycle Pour 1 litre of water into dispenser gt gt and start the Drain programme 64 Index Alignment 61 Anti stain system 31 Basic Settings 3 sec 11 38 Button ecoPerfect 11 16 28 Finish in 11 15 28 Dos IEI 11 17 29 Dos EI 11 17 29 Cancelling the programme 19 Care 40 Drum 40 Machine housing Control panel 40 Changing the programme 19 Childlock 18 28 Descaling 40 Detergent drawer 10 Display panel 11 Dosing recommendation 39 ecoPerfect 11 16 28 Electrical connection 62 Emergency release 46 Faults what to do 48 Getting to know your Hints and tips 7 Aqua Sensor 39 Automatic programmes 26 Options 11 16 30 soeedPerfect 11 16 28 Spin 11 15 28 otart Reload 11 Temperature 11 15 28 Cleaning Detergent drawer 41 the filter 45 the siphon 44 Connecting the water 58 Water drainage 59 Water supply 58 Consumption values 37 Customer service 50 Drain pump blocked 43 Drum light 14 Dyeing Discolouring 27 End of the programme 20 Extra rinse 30 Finish in 11 15 28 appliance 9 Hose and cable lengths 52 65 66 i Dos 10 22 29 Clean the dispenser 41 Drain disp2. 600 rom dispenser gt s according to manufacturer s specifications i The laundry must not be treated with fabric softener Li Before washing remove all fabric softener residue from detergent drawer all dispensers Rinse a Extra rinse with spin O 1200 1600 rom Aa cG A w at 2 0 800 rom detergent softener v detergent softener 25 HASTA The presettings of the programmes are highlighted in bold Programme Type of washing Spin Extra spin with selectable spin speed Options Information O 1200 1600 rom a at 2 0 800 rom detergent softener Spin Low program Extra spin cycle at reduced speed and with especially gentle spin mechanism 0 800 1200 rom a at 2 0 600 rom detergent softener Drain The rinsing water when Rinse Hold wy without final spin is activated detergent softener Automatic programmes The degree of soiling and the type of washing are automatically detected and the washing sequence as well as intelligent dosage are optimally adjusted m Auto for durable textiles m Auto Soft gentler treatment of washing Textile Guard The laundry must not be treated with fabric softener Use special detergents suitable for machine wash Dosage according to manufactu
3. Depending on the programme you can use the programme options to adjust the washing process even more efficiently to your items of washing Programme settings options m Are active without acknowledgement m Can be selected or deselected or changed depending on the programme progress m Settings i Dos IEl and i Dos El are retained after appliance is switched off All other programme settings options must be reset for reselection Buttons Notes Temperature Before and during the programme the presettings Temperature can be changed for as long as the arrows are dis played gt Page 15 Maximum spin speed depends on the programme Spn Spiri and model Finish in Delays the Finished in time end of programme Finish in Before the programme starts the end of the pro gramme can be preselected in h steps up to maximum 24h When the programme has started the preselected time is displayed e g for 8h and counts down until the wash programme starts Then the programme du ration is displayed e g 2 30h When the programme has started the preselected time can be changed as follows 1 Select Start Reload Pll 2 Select Finish in button and change Finish in time 3 Select Start Reload Pil To activate deactivate the Childlock gt Page 18 ecoPerfect For saving energy gt Page 16 lt ecoPerfect 1Q itt speedPerfect O For a shorter wash time gt Page 16 s
4. SIEMENS Washing machine WM14Y891GB siemens home com welcome en Washing machine Instruction Manual and Installation Instructions Register your product online Your new washing machine You have chosen a Siemens washing machine Please take a few minutes to read and become familiar with the advantages of your washing machine To meet the high quality demands required by Siemens every washing machine that leaves our factory is carefully checked to ensure that it functions correctly and is in perfect condition For more information on our products accessories replacement parts and services see our website www siemens home com or contact our after sales service centres If the operating and Installation instructions describe different models any differences will be pointed out at the relevant points in the text T Read these operating and installation instructions before L switching on the washing machine Display rules A Warning This combination of symbol and signal word indicates a possibly dangerous situation Not heeding the warning can cause death or injuries A Caution This signal word indicates a possibly dangerous situation Not heeding the caution can cause property and or environmental damage Information about the optimum use of the appliance any other useful information 1 2 3 a b Cc The steps are represented by numbers or letters E Lists are represented by a small box or a da
5. button Appliance is switched off Turn off the water tap Not required for Aqua Stop models Page 68 21 Programme overview TAS WA Programme Type of washing Name of the programme Brief explanation of the programme and for which textiles it is suitable The presettings of the programmes are highlighted in bold Options Information max load selectable temperature as C selectable spin speeds in rom the max spin speed depends on the model possible programme options for the Less Ironing programme option possible spin speeds in rom possible automatic dosage of a softener and a detergent v can be selected deselected cannot be selected Cotton Hard wearing textiles heat resistant textiles made of cotton or linen i reduced load for speedPerfect O option Page 16 max 8 kg 5 kg cold 60 90 C O 1400 1600 rom Q 0 28 tw at 0 800 rom detergent v softener v Easy Care Textiles made of synthetic materials or blended fabrics max 4 kg cold 40 60 C O 1200 rom Q 0 28 tw at 0 600 800 rom detergent v softener v Mixed Fabrics Mixed load consisting of textiles made of cotton and synthetics max 4 kg cold 40 C O 1400 1600 rom OM ORLAU 28 tw at 0 600 800 rom detergent v softener v 2
6. existing water hardness use a test strip or check with your water utility company My water hardness Here is an example of the detergent dosage on a package label Degree of soiling light normal heavy very Water hardness heavy soft medium 55 ml 75 mi 120 ml 160 ml hard very hard 75 ml 95 ml 150 ml 180 ml li Factory setting of the basic dosage for detergent 75 ml and for softener 36 ml In the case of more concentrated detergents reduce the basic dosage amount m f intensive foaming occurs repeatedly during washing pleas check the basic dosage setting and dosage strength Furthermore some liquid detergents may have a tendency to excessive foaming If the basic dosage settings and dosage strengths are correct it is recommended to use a different liquid detergent Change basic dosage amount Page 38 m f required convert i Dos liz dispenser contents li Instead of softener a second liquid detergent can also be used in dispenser i Dos EI Change dispenser content Page 38 When the i Dos Il container content is switched from softener to detergent the basic dosage amount of detergent for this container is set to the factory setting 75 ml and the dosage for this detergent is set to off in all permitted programmes Then select the detergent dosage light normal or strong via the i Dos IEl button on the display panel Page 17 The i Dos EJ container is automatically deac
7. power cord are installed incorrectly there is a risk of tripping and injury Lay hoses and cables in such a way that there is no risk of stumbling Caution Washing machine may be damaged Frozen hoses may tear burst Do not install the washing machine in an area where there is a risk of frost or outdoors f the washing machine is raised by protruding components e g washing machine door the components may break off and the washing machine may be damaged Do not lift the washing machine by its projecting parts In addition to the safety information listed here the local water and electricity supplier may have special requirements Ifin doubt have the appliance connected by a technician Installation area Stability is important to prevent the washing machine from wandering The installation area must be firm and level Soft floors floor coverings are not suitable Installation on a platform with drawer 54 Platform order no WMZ 20490 WZ 20490 Installing the appliance on a base or on a wooden joist ceiling A Warning Washing machine may be damaged The washing machine may wander during the spin cycle and topple tall off the base Always secure the washing machine feet with fixing brackets Holding brackets order no WMZ 2200 WX 9756 CZ 110600 Z 7080X0 If installing on a wooden joist ceiling lf possible install the washing machine in a corner Screw a water resist
8. removed 1 Drain dispensers before removing them Re attach drawer handle only after cleaning 2 Open drawer 41 3 Press release lever and completely remove drawer 4 Carefully remove drawer cover A Caution Detergent drawer may be damaged The detergent drawer contains electrical components They may be damaged if they come into contact with water Do not clean the cover in the dishwasher and do not immerse in water Protect rear drawer plug from moisture detergent or softener residue if required clean outer surfaces with a soft damp cloth Dry before re inserting 5 Clean tray and cover with soft damp cloth or hand shower Clean inner surface also with a soft damp cloth 6 Dry tray and cover and re assemble 7 Push on drawer handle from above until it locks in place 8 Push in detergent drawer all the way 42 Drain pump blocked A Warning Danger of scalding Wash liquor is hot when washing at high temperatures You may be scalded if you touch the hot wash liquor Allow wash liquor to cool down Turn the tap off to prevent more water from flowing in and to ensure that it is drained via the pump 1 Switch off the device Pull out the mains plug 2 Open service flap 3 Remove service flap 4 Take the drainage hose out of the holder Remove the sealing cap drain water into a suitable receptacle Press on sealing cap and insert drainage hose into the holder N
9. softener running out of the dispensers Leaking detergent softener may impair the function of the appliance e g damage to electronics Before transporting the appliance always drain dispensers Protection of the environment Packaging Old appliance et Dispose of packaging in an environmentally friendly manner This appliance is labelled in accordance with European Directive 2012 19 EU concerning used electrical and electronic appliances waste electrical and electronic equipment WEEE The guideline determines the framework for the return and recycling of used appliances as applicable throughout the EU Hints and tips m Utilise the maximum amount of washing for the particular programme m Wash normally soiled washing without Pre wash m Detergent dosage using the intelligent dosing system helps save detergent and water E Energy saving mode The display panel light goes out after several minutes Start Reload pli flashes To activate the light select any button The energy saving mode is not activated if a programme is running m The selectable temperatures apply to the care labels on the textiles The temperatures in the machine may deviate from this so that you get the optimum mix of energy saving and washing results Automatic switch off If the appliance is not operated for a prolonged period it automatically switches off before the programme starts and when the programme has ended to save energy Swi
10. stopped the spin cycle washing unevenly distributed Distribute small and large items of washing in the drum Less Ironing selected gt Page 30 Too low speed selected gt Page 22 Not a fault unbalanced load detection system adjusts imbalance Not a fault effect of the care product not impaired f required clean insert Faults Cause Remedy Odour formation in Run Cotton 90 C programme without washing the washing Use standard detergent machine Repeated intensive Check basic dosage settings and dosage strength foaming f required use a different liquid detergent Detergent softener Too much detergent softener in the dispensers Observe max mark drips off the sealand in the dispensers collects on the door or in the seal fold i Dos Irl If the i Dos IE content menu setting is changed all settings presetting deleted are changed Page 35 Loud noise Appliance aligned formation vibrations Align the appliance gt Page 61 and wandering Appliance feet fixed during spin cycle Secure appliance feet Page 61 Transportation safety devices removed Remove transportation protection devices gt Page 56 Display panel Power failure indicator lights do Fuse tripped Switch on replace fuse not function while If the fault occurs repeatedly call customer service Page 50 the appliance is running The programme Not a fa
11. tap of an unpressurised hot water apparatus Use only the supplied inlet hose or one purchased from an authorised specialist outlet not a used one Ifin doubt have the appliance connected by a technician Water inlet hose 58 Water inlet hose do not kink crush modify or sever strength is no longer guaranteed Optimum water pressure in the mains 100 1000 kPa 1 10 bar m When the tap is turned on the water flow is at least 8 l min m Ifthe water pressure is higher install a pressure reducing valve 1 Connect the water supply hose Warning Threads for screw connections may be damaged lf the screw connections are tightened too tightly using a tool pliers the threads may be damaged Tighten plastic screw fittings by hand only to the tap 34 26 4 mm Aqua Stop and Aqua Secure Standard on the appliance for Standard and Aqua Secure models 2 Carefully turn on the tap and check that the connection points are not leaking screw connection is under water pipe pressure Water drainage hose Do not kink or protract the the water supply hose Height difference between the placement area and drainage point O maximum 100 cm Drainage into a wash basin A Warning Water damage possible lf the attached drainage hose slips out of the washbasin due to high water pressure when draining the washing machine leaking water may cause damage secure the drainage hose to prevent it
12. 2 AA The presettings of the TA a D f T AN programmes are highlighted in bold Programme Type of washing Options Information Delicates Silk max 2 kg For delicate washable textiles e g made an o of silk satin synthetic fibres or blended OAE fabrics e g silk blouses silk scarf O 600 800 rom 1 el ft Li For machine wash use detergent Q 0 828 0 0 F Suitable for delicates and or silk at 2 0 600 rom detergent v softener v Wool max 2 kg Hand or machine washable wool or rich cold 30 40 C wool textiles Especially gentle wash programme to O 800 rom prevent shrinkage longer programme Sy pauses textiles rest in wash liquor detergent softener v Li Wool is of animal origin e g angora alpaca lama sheep Li For machine wash use detergent suitable for wool Dark Wash max 3 5 kg Dark textiles made of cotton and dark cold 30 40 C easy care textiles Wash textiles inside out O 800 1200 rom Q 0 eae tw at 0 600 800 rom detergent v softener v Rapid 15 max 2 kg Extra short programme approx E E o 15 minutes suitable for lightly soiled Ona Oo washing as a small amounts of laundry 0 800 1200 rom wv T detergent v softener v Textile Guard max 1 kg Washing followed by water proofing cold 30 40 C of weatherproof and out
13. ant wooden panel min 30 mm thick to the floor Appliance installed under between kitchen units A Warning Danger of death from electric shock Danger of death if live parts are touched The appliance cover plate must not be removed 60cm cavity width required Install washing machine only under a continuous worktop connected firmly to the adjacent cupboards 95 Remove transportation protection devices A Caution Washing machine may be damaged Transit bolts which have not been removed may damage e g the drum while the washing machine is running Before using the appliance for the first time remove the 4 transportation protection devices completely and keep in a safe place A Caution Washing machine may be damaged To prevent damage in transit when transporting the washing machine subsequently always re install the transit bolts prior to transportation Keep screw and sleeve screwed together 56 3 Loosen and remove all 4 transportation lock screws Lock covers firmly by pressing on the locking hook 57 o Connecting the water A Warning Danger of death from electric shock Danger of death if live parts are touched Do not immerse Aqua Stop safety device in water contains an electric valve To prevent leakage or water damage follow the instructions in this chapter Operate the washing machine with cold drinking water only Do not connect to the mixer
14. are product follow the instructions of the manufacturers We recommend the use of standard universal and color liquid and gel like detergents for all machine washable coloured textiles made of cotton and synthetic materials 32 m Use only self flowing liquid products and gels which the manufacturer recommends adding to a detergent drawer m Do not mix different liquid detergents If changing the liquid detergent type manufacturer empty the dispenser completely gt Page 47 m Do not use any solvent based corrosive or gas emitting products e g liquid beach m Do not mix detergent and softener m Do not use any superimposed or highly thickened products m To prevent product from drying do not leave the fill cover open for a long time In daily use m Illuminated displays on the drawer handle Display is lit if intelligent dosage is selected for the dispenser In the case of the combined container El the indicator light is lit for the stored container content amp for softener El for detergent Page 38 Display flashes if the fill level for the container is below the minimum when intelligent dosage has been selected Display flashes briefly when drawer has been inserted correctly m Selecting and deselecting intelligent dosage adjusting dosage strength The intelligent dosage of detergent and softener is selected in the factory for all permitted programmes Refer to Page 22 The dosage
15. as with very soft water Water Plus Increased water level more gentle treatment of the on off washing Rinse Hold The washing remains in the water after the last rinse on off cycle End the programme Page 20 Silent Wash Reduced noise values by adjusted spin sequence on off and deactivated end signal Especially suitable for washing at night Li Residual moisture of the washing slightly increased Stains For washing stained laundry Selectable treatment of stains see Page 31 30 a Anti stain system General information about stains The Stains additional programme option for treating special stains can be found via the El Options button A total of 16 different stains can be selected The washing machine adjusts the washing temperature drum movement and soaking time specific to the type of stain Hot or cold water gentle or intensive washing control and long or short soaking provide the wash programme with a special sequence for each type of stain The result stains are treated optimally The treatment of two stains explained in the following example 3 blood Blood is first dissolved in cold water then the selected wash programme starts Q egg Egg particles are removed by soaking in the lukewarm water bath selecting a wash cycle with a high water level and running additional rinse cycles For the other stains we have developed comparable solutions in intensive
16. ated Activate deactivate press Finish in for approx 5 seconds Finish in lt 2 Childlock has been activated Display panel goes back to the Main menu after approx 3 seconds If the programme selector is adjusted or a button is selected while the childoroof lock is active the symbol flashes briefly 18 E Topping up washing When the programme has started washing can be reloaded or taken out as required Select Start Reload Pll aN aN Dos lI 60 C 1 4006 2 31 h i Dos al Reload is possible lf there is a high water level high temperature or if the drum is rotating the washing machine door remains locked for reasons of safety and reload is not possible Follow the information on the display panel To continue the programme select the Start Reload pil button The washing machine door is locked and the programme continues automatically Load display is not active during relosding Do not leave washing machine door open for a prolonged period water could run out of the washing m Changing the programme if you have mistakenly started a wrong programme 1 Select Start Reload Pl 2 Select another programme 3 Select Start Reload pil The new programme starts from the beginning m Cancelling the programme For programmes at high temperature 1 Select Start Reload Pll 2 Cool down washing select Rinse Freshen Up see Others programmes 3 Select Start Reload pill Fo
17. cure installation A Warning Risk of injury The washing machine is heavy caution take care when lifting it f the washing machine is raised by protruding components e g washing machine door the components may break off and cause injuries Donot lift the washing machine by its projecting parts A Caution Risk of stumbling If the hoses and power cord are installed improperly there is a risk of tripping and injury Lay hoses and cables in such a way that there is no risk of stumbling A Caution Washing machine may be damaged Frozen hoses may tear burst Do not install the washing machine in an area where there is a risk of frost or outdoors f the washing machine is raised by protruding components e g washing machine door the components may break off and the washing machine may be damaged Donot lift the washing machine by its projecting parts n addition to the safety information listed here the local water and electricity supplier may have special requirements lf in doubt have the appliance connected by a technician 53 A Warning Risk of injury he washing machine is heavy caution take care when lifting it f the washing machine is raised by protruding components e g washing machine door the components may break off and cause injuries Do not lift the washing machine by its projecting parts Caution Risk of stumbling If the hoses and
18. door clothing with membrane coating and water O 800 rom resistant textiles gt Page 26 Q Wait P detergent softener 23 AA The presettings of the TA A D f T AN programmes are highlighted in bold Programme Type of washing Options Information Shirts Blouses max 2 kg Shirts Blouses made of cotton linen 7 synthetics fibres or blended fabrics cold 40 60 C For non iron shirts the shirts blouses are 0 800 rom given only a short spin using the Less 9 R dU adto Ironing option hang up dripping wet PAA AE Self smoothing effect at 0 400 rom detergent v softener v Li wash shirts blouses made of delicates silk in Delicates Silk programme Hygiene max 7 5 kg 5 kg oe textiles made of cotton or cold 60 C O 1200 1600 rom 1 Especially suitable for increased I wd A hygienic demands or particularly e 0 K L a w sensitive skin on account of prolonged at 0 800 rom washing at a defined temperature with a higher water level and longer rinsing detergent v softener v cycle reduced load for speedPerfect O option Page 16 Curtains max 3 5 kg 3 5 kg heavy curtains or 25 30 m light cold _ 30 40 C curtains Li Pre wash option has been preset QO 400 800 rom Q 0 8 US tw Pf i Reduced rinse and final spin cycle detergent v softener v i For machine wash use de
19. e was inspected thoroughly before leaving the factory To remove any water left over from testing procedures the first washing cycle should be carried out without laundry in the machine The washing machine must have been installed and connected properly See chapter Installing Page 61 1 Check the machine Never switch on a damaged machine Inform your customer service Page 50 PNT FW ND 9 Fill dispensers El amp W Remove protective film from the panel Insert mains plug Turn the tap on Switch on the appliance Close the washing machine door Do not load any washing To prevent unused detergent from flowing into the outlet during the first wash Pour 1 litre of water into dispenser gt and start the Drain programme select and start the Cotton 90 C programme 10 When the programme ends switch off the appliance Your washing machine is now ready for use 63 Transportation e g if moving house Preparatory work 1 Turn off the tap 2 Release the water pressure in the supply hose Maintenance Filter in the water inlet hose Page 45 3 Drain any residual detergent solution Maintenance Drain pump blocked Page 43 4 Isolate the washing machine from the power supply Remove the hoses 6 Drain dispensers Page 47 gl Installing transportation protection devices 1 Remove covers and keep in a safe place If required use a screwdriver 2 Insert all 4 sleeves
20. emover prewash sprays away from the surfaces of the washing machine Using a damp cloth immediately remove any fine spray residue and other residue droplets Empty pockets Remove metal parts paper clips etc Wash delicates in the net bag tights underwired bras Close zips button up covers Brush sand out of pockets and collars Remove curtain fittings or include in the net bag Wash new items separately 2 Preparing the appliance Insert mains plug is f Turn on water tap 3 Selecting a programme and putting the washing in the drum 1 Open the washing machine door 2 Check whether the drum has been completely emptied If required empty Otherwise the load display may malfunction Page 39 3 Press the button The appliance is switched on The Siemens logo is indicated on the display panel and all programme indicator lamps are lit Then always the Cotton programme preset at the factory is displayed Displays for the Cotton programme Sif Pr a ms mas mas Dos 60 c 14006 2 31 h Dos al Nv Nz NY The indicator lamp is lit on the programme selector and the main menu for the selected programme is indicated on the display panel Inthe shell grip of the detergent drawer the indicator lights for intelligent dosage are lit if intelligent dosage has been selected For appliances with drum light After switching on the appliance after opening and closin
21. ensers 41 Filling dispenser 32 In daily use 33 Standard settings 34 switching on the appliance 32 Dos lel 11 17 29 Less Ironing 30 Load adjust 39 Maintenance 40 Old appliance 7 Option Extra rinse 30 Less Ironing 30 Pre wash 30 Packaging Panel 11 Pre wash 30 Programme overview 22 Programme selector 11 Quick reference instructions 8 Rinse Hold 20 30 safety instructions 5 selecting the programme 14 silent Wash 30 Soaking 27 sorting the washing 12 Dos EI 11 17 29 Information on the display panel 47 Insert the laundry 15 the washing 14 Installation 53 Installing transportation protection devices 64 Intended use 4 Load sensor Load display 39 Manual dosage 36 Rinse Hold 30 Silent Wash 30 Stains 30 Water Plus 30 Options 11 16 30 Programme sequence steps 18 Programme setting 15 16 Programme settings 28 Protection of the environment 7 speedPerfect 11 16 28 spin 11 15 28 Stains 30 Standard accessories 51 Starching 27 starting the programme 17 Technical specifications 52 Temperature 11 15 28 Textile Guard 26 Unbalanced load detection system 39 Washing Insert laundry 13 Topping up washing 19 Transport bolts 56 Unloading the laundry 21 Water Plus 30 67 9000965240 9405
22. flowing in Dispenser is empty and fill level display is not flashing Wrong detergent softener has been poured into dispenser Detergent softener congealed in the dispensers Washing machine door cannot be opened Programme does not start Detergent solution is not drained Water not visible in the drum Spin result not satisfactory Washing wet too damp Spin cycle activated several times Residual water in the dispenser for care product 48 Correctly attach replace drainage hose Tighten screw fitting on the supply hose Start Reload Pll not selected Tap not open Filter blocked Clean the filter Page 45 Supply hose kinked or jammed Drawer cover rear drawer plug dirty Cleaning Page 41 Detergent drawer not inserted correctly Insert correctly Page 33 Dispensers 1 Drain and clean dispensers 2 Refill dispensers gt Page 32 Clean and refill dispensers Safety function active Stop programme Page 19 Rinse Hold wy without final spin selected gt Page 20 Can be opened via emergency release only gt Page 46 Start Reload pil or Finish in time selected Door closed Childlock active Deactivate gt Page 18 Rinse Hold w without final spin selected gt Page 20 Clean the drain pump Page 43 Clean outlet pipe and or drainage hose Not a fault water below the visible area Nota fault unbalanced load detection system has
23. from slipping out of the sink A Caution The appliance may be damaged If the end of the drainage hose is immersed in the drained water water may be drawn back into the appliance The plug must not be in the plug hole When the water is being pumped out of the washing machine check that the water drains away quickly enough The end of the drainage hose must not be immersed in the drained water Installing the drainage hose 59 Drainage into a siphon A Warning Water damage possible If the drainage hose slips off the siphon connection due to high water pressure when draining the washing machine leaking water may cause damage Connection point must be secured with hose clip 24 40 mm specialist outlet Connecting Drainage into a plastic pipe with rubber sleeve or into a gully A Warning Water damage possible If the drainage hose slips off the plastic pipe due to high water pressure when draining the washing machine leaking water may cause damage secure the drainage hose to prevent it from slipping out of the sink Connecting 60 Alignment 1 Loosen lock nut in a clockwise direction with a wrench 2 Check alignment of the washing machine with a spirit level and if required correct Adjust the height by rotating the foot All four feet must be firmly on the floor The washing machine must not wobble 3 Tighten the lock n
24. ft washing softener or for heavily soiled or stained washing detergent when container content Detergent set E i Dos El for dosing a liquid detergent Selecting i Dos EJ and changing dosage strength 60 C 2 3 1n light i Dos t dosage normal strong Nz Nz normal for normally soiled washing Do not manually dose additional detergent into detergent drawer gt gt if intelligent dosage for detergent has been activated prevents overdosage and foaming 5 Starting the programme m Select Start Reload pil The indicator light is on Start Reload Pll Washing During the wash cycle the programme progress Is indicated by a bar on the display panel The bar progresses in the course of the wash cycle and provides information about the current programme progress The arrows are switched on and off according to the programme progress They indicate the programme settings options which can be changed added as the programme progresses Some programme sequence steps explained m Load adjust active Page 39 mas mas i Dos I 60 c 14006 2 31 h i Dos iE Load adjust active m Prewash wash rinse spin drain are displayed during the wash cycle E Rinsing with aqua sensor Page 39 E Extra rinse foam m Other displays Page 47 During washing m Childlock To prevent the set functions of the washing machine from being accidentally changed the childproof lock can be activ
25. g the washing machine door as well as after starting the programme the drum is lit The light goes out automatically 4 Select a programme You can use the saved programme or select another programme Programme overview refer to Page 22 or select other programmes see Others and choose one programme as follows e g Outdoor 30 C 800 1 04h Down Wear Additional programms Outdoor ouaadd Rinse Main menu w SE TAN Select programme using the buttons under the arrows The selection is acknowledged by a tick Wait or back by pressing Main menu button selected programme is indicated on the display panel aN aN aN 30 c 8006 1 04n Outdoor To change the programme select button under the black highlighted programme and change programme 5 Insert the washing Dosage automatic Please load laundry max 8kg The load screen for the selected programme e g for Cottons is indicated on the display panel Displays for recommended dosage Dosage automatic if intelligent dosage has been preset Dosage recommended dosage if no intelligent dosage preset see Manual dosage gt Page 36 Unfold and load presorted items of washing Mix large and small items Washing items of different size distribute themselves better during the spin cycle Individual items of washing may cause an unbalanced load Page 39 Do not load washing until the main menu fo
26. g when the power supply is restored If the washing Is still to be removed the door can be opened as described below Warning Danger of scalding Wash liquor and washing may be hot If touched there is a risk of scalding If required leave to cool down Caution rina when reaching into gripping the rotating rum If you reach into the rotating drum you may injure your hands Do not grip the rotating drum Wait until the drum stops rotating Caution Water damage possible Leaking water may cause damage Do not open the door if you can still see water through the glass 1 Switch off the appliance Pull out the mains plug 2 Drain the water 3 Pull down emergency release with a tool and release Door can then be opened Information on the display panel Display Cause Remedy The door cannot be Washing may be caught Please open and close washing locked please open machine door again and select Start Reload Pil the door again then If required shut washing machine door or remove washing and close it and select shut again start pause f required switch appliance off and on again set programme and make individual settings start programme Please re fill Level i Dos container below minimum Top up Page 32 i Dos l I i Dos Ef container Dos lel i Dos E Set i Dos XIE iDos El to off error deactivate Call customer Service Appliance can continue to be operated with i D
27. ginal spare parts 50 E Standard accessories depending on model Aqua Stop Standard Aqua Secure Mains cable Water outlet Water inlet Instruction manual and Installation instructions CAAO Mw 8 a Elbow for securing the d water outlet hose Spanner Also required for connection of the water drainage hose to a siphon 1 hose clip 24 40 mm DIY store is also required for connection to a siphon Connecting the water Page 60 Useful tools E Spirit level for alignment m Socket wrench size 13 for loosening the transportation protection devices Page 56 and size 17 for aligning the appliance feet Page 67 51 Hose and cable lengths depending on model Connection on left side or Connection on right side 7100 cm 150 cm If the hose holders are used the possible hose lengths are reduced Available from dealer customer service m Extension for Aqua Stop or cold water inlet hose approx 2 50 m Order no WMZ2380 WZ10130 CZ11350 Z7070X0 m Longer supply hose approx 2 20 m for standard model Technical specifications Dimensions 60 x 59 x 85 cm width x depth x height Weight depending on modell 63 83 kg Mains connection Nominal voltage 220 240 V 50 Hz Nominal current 10 A Nominal power 2300 W Water pressure 100 1000 kPa 1 10 bar 92 Installation Humidity in the drum is caused by the final inspection Se
28. i Dos EJ 1 31 and i Dos Sle 0 5 I in the detergent drawer are used for this You can select whether you want to use one liquid detergent and one softener or two liquid detergents Depending on the selected programme and settings the optimum amounts of detergent softener are dosed via the i Dos containers At the factory the dosage has been preset for i Dos detergent for lightly soiled washing and j Dos IE softener for normally soft washing Overview of the i Dos settings starting on Page 22 Dispenser for intelligent dosage liquid detergent Dispenser amp El for intelligent dosage softener or liquid detergent Dispenser gt s for manual dosage Page 36 a Operating elements Display elements Auto Cotton lt _ Temperature Spin Finish in E Options Basic Settings 3 sec Auto Easy Care Curtains Mixed Fabrics Hygiene Delicates Silk 4 Shirts 4 Wool Textile Guard Dark Wash 00770070 Others Rapid 15 looogg ogg speedPerfect C i Dos liel All buttons are sensitive they only need to be touched gently Indicator lights for intelligent dosage Start Reload button to start interrupt Page 33 and cancel the programme e g reload Button ecoPerfect amp Page 16 washing Page 28 Simultaneously hold down Basic Press the main switch button Switch Settings 3 sec for appliance setting
29. ies and by persons who have inadequate experience or knowledge provided they are supervised or have been instructed by a responsible person Keep pets away from the washing machine Read and follow the operating and installation instructions and all other information enclosed with the washing machine Retain documents for subsequent use Safety instructions A Warning Danger of death from electric shock Danger of death if live parts are touched Never pull out the mains plug by tugging the power cord Insert pull out the mains plug with dry hands only A Warning Risk to children Do not leave children unsupervised near the washing machine Children must not play with the washing machine This will prevent children from locking themselves in and suffocating On redundant appliances Pull out the mains plug Sever the power cord and discard together with the plug Destroy the lock on the washing machine door Children must not perform any cleaning or maintenance work without Supervision When playing children may become entangled in the packaging Tilm and packaging parts or pull them over their heads and suffocate Keep packaging plastic film and packaging parts out of the reach of children When washing at high temperatures the glass of the washing machine door becomes hot Prevent children from touching the hot washing machine door Detergents and care product
30. ion requires changing e g due to changes in the programme settings options foam detection unbalanced load detection the load or soiling ecoPerfect Energy optimised washing by reducing the temperature while F 7 achieving a consistent washing result When selected the lt ecoPerfect Q display lamp is lit The washing temperature is lower than the selected temperature For special hygiene requirements the Hygiene programme is recommended gt Page 24 speedPerfect U For a shorter wash time with a comparable washing effect to the standard programme Observe maximum load Refer speedPerfect O Page 22 When selected the display lamp is lit E Options Overview of all options Page 30 Select H Options and e g amp Water Plus button 60 C E Options Extra rinse Water Plus Rinse Hold Nv Select option by pressing the two buttons displayed on the left Select deselect option by pressing the two buttons displayed on the right The selected options are immediately active In the case of multi level settings keep touching the buttons to run through the settings automatically Wait or back to the main menu by pressing E Options button 16 i Dos Sl for dosing a softener or a second liquid detergent Selecting i Dos lz and changing dosage strength 60 C normal i Dos SI dosage strong off Nv Nv i Dos f strong for especially so
31. leaning agents Caution Washing machine may be damaged If solvent cleaning agents e g petroleum ether are used on the washing machine the surfaces may be damaged Do not use solvent based cleaning agents Machine housing Control panel Drum Descaling 40 Remove detergent residue immediately Wipe with a soft damp cloth Do not clean the appliance with a water jet Use chlorine free cleaning agent not steel wool If there is an odour in the washing machine run Cotton 90 C programme Use standard detergent Not required if detergent dosed correctly However if this does occur follow the instructions of the descaling agent manufacturer Suitable descalers can be purchased on our website or from customer service Page 50 i Dos Clean the detergent drawer Drain dispensers The dispensers have drainage openings with removable stoppers in the front area To drain the dispensers first remove the drawer handle as illustrated 1 Open detergent drawer 2 Pull release lever A on the back of the drawer handle bottom middle gently towards yourself and simultaneously pull up released drawer handle B 3 To drain the the dispensers carefully remove the respective sealing plug and drain the contents into a Suitable receptacle 4 Reinsert sealing plug all the way Cleaning dispensers detergent drawer To clean the drained dispensers the detergent drawer can be completely
32. ons are held down the settings automatically run through m Select Setting with the two left buttons m Select displayed value with the two right buttons selection acknowledged by a tick m Wait or hold down Basic Settings 3 sec buttons again settings are retained after appliance is switched off Settings Set values Notes end signal off quiet medium Adjust volume of the end signal loud very loud button signal off quiet medium Adjust volume of the button signals loud very loud Auto power in 15 30 60 min The appliance automatically switches off after off of the never min 0 kWh energy consumption to switch appliance on press main switch button language German Change displayed language English i Dos amp El Softener Select dispenser contents content Detergent i Dos amp El 10 ml 200 ml Set basic dosage according to recommendation i Dos l 10 mi 200 mi of the detergent softener manufacturer 38 Sensors Your washing machine is so intelligent Load adjust Depending on the type of textile and load the load adjust optimally adjusts the water consumption in each programme Aqua Sensor During the wash and rinse cycles the Aqua sensor checks the degree of turbidity turbidity is caused by dirt and detergent residue of the washing and rinsing water The duration and number of rinse cycles are specified depending on the water turbidity and if req
33. os Itf i Dos EJ manual dosage Page 36 Please close Push in detergent drawer correctly gt Page 33 detergent drawer Please open tap Turn on tap fully Supply hose kinked jammed Water pressure too low Clean the filter Page 45 Please clean pump Drain pump blocked Clean the drain pump Page 43 The water drainage pipe drain hose is blocked Clean the drainage hose on the siphon gt Page 44 Pause Reload isnot Water level or temperature is too high possible Select Start Reload Pil to continue the programme Door cannot be Water level or temperature is too high unlocked Water Select Start Reload pil to continue the programme level or temperature is too high aquastop has been not applicable without Aqua Stop activated Water in the base pan appliance leaking Please callcustomer Call customer service gt Page 50 service Auto power off in Appliance automatically switches off after seconds if it is not seconds operated for a prolonged period In order to cancel the programme press any button gt Page 38 Water cooling To protect the wastewater pipes the hot detergent solution is cooled before being drained Other displays Switch off appliance wait 5 seconds and switch on again If the Error E XXX display is indicated again call customer service gt Page 50 41 Faults what to do arc LULL R Cause Remedy Water is running out Water not
34. ote Residual water may run out 5 Carefully unscrew the pump cover Clean the interior pump cover thread and pump housing fan impeller in the detergent solution pump must rotate 6 Reinsert and screw on pump cover Handle should be vertical 43 7 Insert service flap 1 engage 2 and close 3 To prevent unused detergent from flowing into the outlet during the next wash cycle Pour approx 1 litre of water into dispenser gt lt gt and start the Drain programme Drainage hose on the siphon blocked 1 Switch off the appliance Pull out the mains plug Note Residual water may run out 2 Loosen hose clip carefully remove drainage hose 3 Clean drainage hose and siphon spigot 4 Re attach drainage hose and secure connection point with hose clip 44 Filter blocked in water inlet hose First release water pressure in the supply hose 1 2 3 Turn off the tap Select any programme except Spin Drain Select Start Reload pil Leave programme for approx 40 seconds Press the button Appliance is switched off Pull out the mains plug Clean the filter Disconnect the hose from the water tap Clean filter with small brush and or for standard and Aqua Secure models Remove hose from the rear of the appliance Take out filter with pliers and clean Connect the hose and check for leaks 45 46 a Emergency release The programme continues runnin
35. peedPerfect 28 Buttons Notes i Dos SE To change the softener dosage strength or deter meow light normal gent when container content detergent set for the strong off selected programme permanently until the next change gt Page 17 light slightly soft washing normal normally soft washing strong especially soft washing i Dos El To change the detergent dosage strength for the se i Dos tf light normal lected programme permanently until the next change strong off Page 17 light lightly soiled washing normal normally soiled washing strong heavily soiled or stained washing 29 Press E Options button to select Notes Pre wash For heavily soiled washing on off For intelligent dosage Selected detergent is used for prewash and main wash To prevent overdosage select medium i Dos setting For manual dosage Divide detergent for pre wash and main wash Put detergent for prewash in the drum and pour detergent for main wash in dispenser gt gt Less Ironing Reduces creasing by special spin sequence followed on off by fluffing and reduced spin speed Li Residual moisture of the washing slightly increased Extra rinse Additional rinse cycles depending on the 1 Rinse programme prolonged programme duration ey 2 Rinses eet ee Li Recommended application for particularly sensitive skin or and in are
36. r programmes at low temperature 1 Select Start Reload Pil 2 Select Spin or Drain see Others programmes 3 Select Start Reload Pll E End of programme by Rinse Hold Rinse hold reached Select spin or drain and then start Spin Drain Nv Nv 1 Select Spin If required adjust the spin speed or Drain 2 Select Start Reload Pl End of the programme Finished remove washing is indicated on the display panel Finished remove washing lf Foam has been detected is also indicated on the display panel the washing machine has detected too much foam during the wash programme and therefore automatically activates additional rinse cycles to eliminate the foam Dose less detergent in the next wash cycle with the same load Reduce basic dosage Page 34 20 After washing Open washing machine door and remove washing D Remove the washing D Switch off the device Do not leave any items of washing in the drum In the next wash they may shrink or discolour something else Remove any foreign objects from the drum and the rubber seal risk of rust Leave detergent drawer and door open so that residual water can evaporate Before switching the machine off Always remove the washing Otherwise the load display may malfunction Always wait until the programme ends as the appliance could still be locked Then switch the appliance on and wait for the unlocking device Press the
37. r the saved programme is displayed after the Siemens logo The load screen is indicated when the door is opened or when the amount of washing Is changed The load bar progresses as the washing machine is loaded If the max load is exceeded the bar flashes Do not exceed indicated max load Overfilling reduces the washing result and encourages creasing 4 Changing the settings of the selected programme Take care not to trap any items of clothing between the loading door and rubber seal Close the door mas mas mas Dos amp l 60 c 14006 2 31 h i Dos al Nz Nv Nv The main menu for the selected programme is indicated again on the display panel You can use the displayed presettings or adjust the selected programme optimally to the items of washing by changing the oresettings or selecting additional settings options m Change Temperature Spin Finish in time selecting and changing e g the Temperature ms mas mas 70 60 c 14006 2 31h no i El Temperature 50 Nz Nv Nv The arrows on the display panel indicate which buttons are used to change the settings The settings are active without acknowledgement and are displayed in the main menu Ifthe buttons are held down the set values automatically run through The respective programme duration is displayed by selecting the programme The programme duration is adjusted while the programme is running if the programme durat
38. rer s instructions 1 Set programme selector to Textile Guard 2 Dose special detergent for outdoor textiles in dispenser gt 26 3 Select Start Reload pil Programme stops before last rinse cycle Rinse hold reached Please add to detergent drawer the water proofing agent and then select start 4 Dose textile guard agent max 170 ml in dispenser gt 5 Select Start Reload pil After treatment of the washing according to manufacturer s instructions Starching The washing should not be treated with fabric softener select Rinsing programme Manually dose liquid starch into dispenser gt if required clean beforehand according to manufacturer s instructions select Start Reload Pil Dyeing Discolouring Dye in household quantities only Salt may attack stainless steellObserve specifications of the dye manufacturer Do not discolourwashing in the washing machine Soaking 1 Dose detergent with i Dos or pour into dispenser gt according to manufacturer s instructions 2 Set programme selector to Cotton 30 C and select Start Reload Pil 3 After approx 10 minutes select Start Reload Pll to stop the programme 4 After the required soaking time reselect Start Reload Pll if the programme is to be continued or change the programme Insert washing of the same colour No additional detergent required the soaking solution is used for washing Zt Programme settings options
39. s on and off the appliance end signal button signal language Programme selector can be rotated in autom switch off Dos settings for either direction Programme Overview approx 3 seconds Overview of all refer to Page 22 settings gt Page 38 Button speedPerfect Page 16 Display panel for settings and Page 28 information Buttons Temperature Spin E Select E Options for additional Finish in time Page 15 Page 28 programme options Page 17 i Dos Sl button Dosage Page 17 Overview of all options Page 30 Page 29 i Dos El button Dosage Page 77 Page 29 Before each washing i Install and connect washing machine properly Refer to Page 53 Before the 1st wash wash once without any washing Page 63 1 Preparing the washing Sorting the washing according to 12 Type of fabric fibre Colour Soiling Follow manufacturer s care information Care label specifications Cottons 95 C 90 C Coloureds 60 C 40 C 30 C Easy Care 60 C 40 C 30 C Delicates 40 C 30 C Hand and machine washable silk and woollens cold 40 C 30 C Do not wash laundry in the washing machine Protecting the washing and the machine When dosing all detergents cleaning aids cleaning products and cleaning agents always follow the manufacturer s instructions Keep detergents and agents for the pretreatment of washing e g stain r
40. s may cause intoxication if consumed or eye and skin Irritation if touched Keep detergents and care products out of the reach of children A Warning Risk of explosion Items of washing pretreated with solvent detergents e g stain remover petroleum ether may cause an explosion when the washing machine has been loaded Before hand thoroughly rinse items of washing by hand Caution Danger of scalding When washing at high temperatures you may be scalded if you touch the hot wash liquor e g if draining hot wash liquor into a washbasin or if draining the washing machine in an emergency Allow detergent solution to cool down A Caution Risk of damaging appliance Cover plate may break Do not climb on the washing machine Opened washing machine door may break off or washing machine may overturn Do not lean on the open washing machine door Caution Danger when reaching into gripping the rotating drum If you reach into the rotating drum you may injure your hands Do not grip the rotating drum Wait until the drum stops rotating Caution Risk of coming into contact with liquid detergents care products If the detergent drawer is opened while the washing machine is running detergent care product may spray out Caution when opening the detergent drawer In case of eye skin contact rinse thoroughly lf accidentally swallowed seek medical advice Caution Hazard due to detergent
41. sh Contents Before washing Intended use safety instructions Protection of the environment The main points in brief Getting to know your appliance Detergent drawer Operating elements Display elements Operating the appliance Before each washing Washing After washing Programme overview Programme settings options Anti stain system Intelligent Dosing System Consumption values Appliance settings sensors Your washing machine is so intelligent Cleaning and maintenance Care and maintenance Emergency release Information on the display panel Faults what to do Customer service Installing the appliance Index standard accessories Installation Remove transportation protection devices Connecting the water Alignment Electrical connection Before the 1st washing Transportation e g if moving house Intended use For use in the household only The washing machine is suitable for washing machine washable textiles and hand washable wool in wash liquor The washing machine is suitable to be operated with cold drinking water and commercially available detergents and care products which are suitable for use in washing machines When dosing all detergents cleaning aids cleaning products and cleaning agents always follow the manufacturer s instructions The washing machine may be operated by children from 8 years of age by persons who have limited physical sensory or mental abilit
42. softener and fabric conditioner with water Prevents blockage of the overflow f detergent is dosed manually no additional detergent via intelligent dosage set intelligent dosage to off It prevents overdosage and foaming 36 Consumption values Programme Load Energy Water Programme consumption duration Cotton 20 C 8 kg 0 25 kWh 57 22 h Cotton 40 C 8 kg 1 09 kWh 57 23 4 h Cotton 60 C 8 kg 1 43 kWh 57 23 4 h Cotton 90 C 8 kg 2 40 kWh 69 22 h Easy Care 40 C 4 kg 0 65 kWh 46 2 h Mixed Fabrics 4 kg 0 59 kWh 44 114 h Delicates Silk 2 kg 0 15 kWh 34 Yah Wool 30 C 2 kg 0 19 kWh 39 Yah Programme Additonal function Load Annual energy Annual water consumption consumption Cotton lt _ ecoPerfect 8 4 kg 137 kWh 10120 Programme setting for testing and energy labelling according to directive 2010 30 EU with cold water 15 C The values may deviate from the stated values depending on water pressure and hard ness room temperature type and amount of laundry detergents used fluctuations in the mains voltage and selected additional functions 37 eS Appliance settings By pressing the Basic Settings 3 sec buttons appliance settings can be changed e g button signal simultaneously hold down Basic Settings 3 sec buttons for _ approx 3 seconds Basic Settings 3 sec Language end signal button signal Nz m ifthe butt
43. strength for detergent has been preset to light lightly soiled washing and for softener to medium normally soft washing and can be individually changed for each programme Refer to Page 17 In addition to intelligent dosage washing additives e g stain remover can be added manually via dispenser gt 9 Page 36 The selection on off of i Dos lz and i Dos EJ is retained for each programme until the next change occurs even if the machine is switched off 33 Reloading detergent softener The flashing of the associated illuminated display when intelligent dosage is selected and a corresponding message on the display panel indicate that the level is below the minimum There are still enough contents for approx 3 washes The same detergent or softener can be topped up at any time If the product manufacturer is changed we recommend cleaning the dispensers beforehand Page 47 If required adjusting the basic dosage Page 34 Standard settings 34 If required change basic dosages for detergent and softener The basic dosage amount to be set corresponds For detergents to the manufacturer s recommendation for normal soiling and to the particular water hardness For softeners to the manufacturers recommendation for medium softness and to the particular water hardness This information can be found on the package label of the detergent softener or ask the manufacturer directly To determine the
44. studies Selectable treatment of stains 3 baby food soil sand orange dirty socks 7 blood WW grass red wine grease oil Q egg coffee 5 chocolate amp tea strawberry lt cosmetics T sweat tomatoes 31 e Intelligent Dosing System Your washing machine features an intelligent dosing system for liquid detergent and softener Dispensers i Dos I 1 3 1 and Dos amp l 0 5 I in the detergent drawer are used for this You can select whether you want to use one liquid detergent and one softener or two liquid detergents Depending on the selected programme and settings the optimum amounts of detergent softener are dosed via the i Dos containers Switching on the appliance The appliance has been preset at the factory for dosing a liquid detergent and a fabric softener identified by corresponding filling lids m Standard universal detergent m amp Softener only i Dos Sl Filling dispenser 1 Open detergent drawer 2 Open fill cover 3 Pour detergent softener Fill disoenser maximum up to max marking 4 Close fill cover 5 Slowly push in detergent drawer all the way When the appliance is switched on the completely inserted drawer is indicated by m Associated display is lit when intelligent dosage i Dos EI Dos amp El is selected Page 33 m Display flashes once and goes out if intelligent dosage is not selected gt Page 33 When selecting your detergent and c
45. tch on by pressing main switch button m lf the washing is then dried in the tumble dryer select spin speed according to the instructions of the dryer manufacturer The main points tn brief A gt o sie Insert mains plug Open the washing To switch on press select the Turn the tap on machine door the button programme e g Cotton Dosage automatic D ibe Please load laundry max 8kg i sort the washing Insert the washing Do not exceed maximum load D NL Start Reload Pll Close the washing If required change programme settings of the select machine door selected programme and select programme Start Reload Pl settings options Finished remove washing f End of the programme For switching the Turn off the mains machine on press supply for models the button without Aqua Stop Getting to know your appliance Operating Detergent drawer elements Display a ___ 4 elements Drum light depending on model Door Service flap N X i i Opening and closing the door Service flap a Detergent drawer i Dos Sulu SIEMENS Intelligent Dosing System i Dos Your washing machine features an intelligent dosing system for liquid detergent and softener Dispensers
46. tergent suitable for curtains Auto max 6 kg O Hard wearing textiles automatic up to 40 C The degree of soiling and the type of washing are automatically detected and automatic up to 1400 rom the washing sequence as well as wo intelligent dosage are optimally adjusted 2 Page 26 detergent v softener v 24 The presettings of the TA p T AN programmes are highlighted in bold Programme Type of washing Options Information Auto Soft max 3 5 kg Gentler treatment of washing The degree automatic up to 30 C of soiling and the type of washing are automatically detected and the washing automatic up to 1000 rpm sequence as well as intelligent dosage TAE are optimally adjusted gt Page 26 oa detergent v softener v The presettings of the TA Di T INN programmes are highlighted in bold Programme Type of washing Options Information Down Wear max 2 kg amp Machine washable textiles filled with cold 40 60 C O 1200 rom Wash large items individually Use IR wot ot mild detergent Measure detergent Q 0 Beco sparingly detergent softener down pillows blankets Outdoor max 2 kg Weatherproof and outdoor clothing with a cold 30 40 C membrane coating and water resistant textiles O 800 rom t i Use special detergents suitable for Q O 8 2 2 5 0 F machine wash Pour detergent into at 2 0
47. tivated if the detergent dosage is activated for the i Dos IJ container The settings are retained for this programme until the next change When the i Dos II container content is switched to softener the basic dosage amount is set to factory setting 36 ml and the dosage is set to normal in all permitted programmes switching over the container contents requires an additional acknowledgement via the display panel A change to the i Dos content resets the i Dos IE settings to their standard value Cancel Continue 35 aa Manual dosage Lo g In the case of programmes in which intelligent dosage is not possible or not requested then set intelligent dosage to off detergent is added to detergent drawer gt In addition to intelligent dosage of detergents cleaning agents such as water softener bleach or stain remover can also be dosed here 1 Pull out the detergent drawer 2 Dosing in dispenser gt s according to Dosage recommendation on the display panel e g for Cottons Dosage 70 Please load laundry max 8kg Depending on the amount of washing in the washing machine a dosing recommendation is indicated on the display panel Soiling Water hardness Page 34 or ask your water supply company Manufacturer s instructions When dosing all detergents cleaning aids and cleaning agents always follow the manufacturer s instructions Dilute viscous fabric
48. uired an additional amount of detergent is dosed in the automatic programmes Load sensor Load display The load sensor detects the load level in the washing machine when the door is open This is indicated by a progressing bar on the display panel To ensure that the load sensor measures all the laundry the drum must be empty before the washing machine Is switched on Dosing recommendation The dosing recommendation indicates a recommended detergent dosage as a depending on the selected programme and the detected load The indicated refers to the recommendation of the detergent manufacturer By observing the recommended dosage you will protect the environment and reduce your household costs Unbalanced load detection system The automatic unbalanced load detection system spins the laundry several times to ensure even distribution For reasons of safety the speed is reduced or does not perform a spin cycle if the washing is very unevenly distributed Distribute small and large items of washing in the drum Faults what to do gt Page 48 39 Care and maintenance A Warning Danger of death from electric shock Danger of death if live parts are touched Switch off the appliance Pull out the mains plug Caution Fire and explosion hazard If solvent cleaning agents e g petroleum ether are used in the washing machine components may be damaged and toxic fumes generated Do not use solvent based c
49. ult unbalanced load detection system adjusts takes longer than imbalance by repeatedly distributing the washing usual Nota fault foam detection system active several rinse cycles are switched on Detergent residue Occasionally phosphate free detergents contain water insoluble on the washing residue Select Rinsing or brush the laundry after washing In the pause status Water level too high Washing cannot be reloaded Immediately Start Reload PII close washing machine door flashes very quickly Select Start Reload pil to continue the programme and a signal sounds If a fault cannot be rectified switching the machine on and off or a repair is required Switch off the appliance and pull out the mains plug Turn off the tap and call customer service gt Page 50 49 Customer service If you cannot rectify the fault yourself Faults what to do Page 48 please contact our customer service We will always finds a suitable solution to avoid unnecessary visits by technicians Please give customer service the product number E Nr and the production number FD of the appliance These instructions can be washing machine door open service flap and Product number Production number rear of the appliance depending on model Rely on the competence of the manufacturer Contact us You can therefore be sure that the repair is carried out by trained service technicians who carry ori
50. ut against the housing Grip the foot and do not adjust the height The lock nuts on all four appliance feet must be screwed tightly against the housing Loud noise formation intense vibrations and wandering may be due to incorrect alignment 61 Electrical connection Electrical safety A Warning Danger of death from electric shock Danger of death if live parts are touched 62 Never pull out the mains plug by tugging the power cord Insert pull out the mains plug with dry hands only Never pull out the mains plug during operation Connect the washing machine to an alternating Current via a correctly installed earthed socket only The mains voltage and voltage specifications on the washing machine appliance rating plate must match Connected load as well as required fuse are indicated on the appliance rating plate Ensure that Mains plug and socket match fit Cable cross section is adequate Earthing system has been installed correctly A damaged power cord may be replaced by an electrician only A replacement mains cable can be obtained from customer service Do not use multiple plugs couplings or extension cables If a residual current operated circuit breaker is used use only a type which features this symbol IAN Only this symbol guarantees compliance with currently valid regulations The mains plug must be accessible at all times Before the 1st washing The washing machin
Download Pdf Manuals
Related Search