Zanussi ZDF14001KA dishwasher
Contents
1. 5 Processing residues can stay in the appli ance Start a programme to remove them Do not use detergent and do not load the baskets If you use the combi detergent tablets activate the Multitab option Water softener adjustment Clarke Level degrees 58 63 10 53 57 46 52 36 45 28 35 6 23 27 51 18 22 13 17 5 12 lt 5 12 The indicator continues to flash The display shows the current setting of the water softener e g 5 level 5 5 Press Multitab again and again to change the setting 6 Press the on off button to deactivate the appliance and to confirm the setting Filling the salt container Caution Water and salt can come out from the salt container when you fill it Risk of corrosion To prevent it after you fill the salt container start a programme www zanussi com To adjust the released quantity of rinse aid turn the selector between position 1 lowest quantity and position 4 highest quantity Put 1 litre of water in the salt container only for the first time Filling the rinse aid dispenser Daily use 1 Open the water tap 4 Add the detergent 2 Press the on off button to activate the ap If you use the combi detergent tablets pliance Make sure that the appliance is in activate the Multitab option setting mode refer to Setting and starting 5 Set and start the correct programme for a programme2. the type of load and the degree of soil If the salt indicator is on fill the salt con tainer f the rinse aid indicator is on fill the rinse aid dispenser 3 Load the baskets www zanussi com Using the detergent Put the detergent or the tablet in compartment A If the programme has a prewash phase put a small quantity of detergent in compart ment B Setting and starting a programme Setting mode For some settings it is necessary that the ap pliance is in setting mode The appliance is in setting mode when after the activation the programme duration flashes in the display If the control panel does not show this condi tion press and hold at the same time Multi tab and Delay until the appliance is in setting mode Starting a programme without delay start 1 Open the water tap 2 Press the on off button to activate the ap pliance 3 Close the appliance door 4 Turn the knob until the programme marker is aligned with the programme you want to set The duration of the programme flashes in the display 5 Press Start The programme starts and the indicator of the running phase is on The programme duration starts to de crease with steps of 1 minute Starting a programme with delay start 1 Set the programme 2 Press Delay again and again until the dis play shows the delay time you want to set from 1 to 24 hours The delay time flashes in the display
3. 3 Press Start The countdown starts to decreases with steps of 1 hour When the countdown is completed the pro gramme starts and the indicator of the running phase comes on Opening the door while the appliance operates If you open the door the appliance stops When you close the door the appliance con tinues from the point of interruption Cancelling the delay start while the countdown operates 1 Press and hold at the same time Multi tab and Delay until the programme dura tion flashes in the display 2 Press Start to start the programme Cancelling the programme 1 Press and hold at the same time Multi tab and Delay until the programme dura tion flashes in the display Make sure that there is detergent in the detergent dispenser before you start a new programme At the end of the programme The display shows 0 00 and the phase indica tors go off 1 Press the on off button to deactivate the appliance www zanussi com 2 Close the water tap lf you do not press the on off button the AUTO OFF function automatically deacti vates the appliance a few minutes after the end of the programme This helps to decrease the energy consump tion Important Let the dishes become cold before you re move them from the appliance Hot dishes can be easily damaged Hints and tips The water softener Hard water contains a high quantity of miner als that can cause damage to the appliance and
4. User manual MANUAL ZDF14001WA ZDF14001KA ZANUSSI ZDF14001SA Contents Safety instructions Control panel Programmes Options Srs ee a Before firstuse_______________ Daily use SI 9 QI BEN A Safety instructions Before the installation and use of the appli ance carefully read the supplied instructions The manufacturer is not responsible if an in correct installation and use causes injuries and damages Always keep the instructions with the appliance for future reference Children and vulnerable people safety Warning Risk of suffocation injury or permanent disability Do not let persons children included with reduced physical sensory reduced mental functions or lack of experience and knowl edge use the appliance They must have su pervision or instruction for the operation of the appliance by a person who is responsi ble for their safety Do not let children play with the appliance Keep all packaging away from children Keep all detergents away from children Keep children and pets away from the appli ance door when it is open Installation Remove all the packaging Do not install or use a damaged appliance Do not install or use the appliance where the temperature is less than 0 C Obey the installation instruction supplied with the appliance Electrical connection Warning Risk of fire and electrical shock The appliance must be earthed 2 Care and cleanin
5. bad washing results The water softener neutralises these minerals The dishwasher salt keeps the water softener clean and in good conditions lt is important to set the right level of the water softener This makes sure that the water softener uses the correct quantity of dishwasher salt and water Using salt rinse aid and detergent Only use salt rinse aid and detergent for dishwasher Other products can cause damage to the appliance The rinse aid helps during the last rinsing phase to dry the dishes without streaks and stains Combi detergent tablets contain detergent rinse aid and other added agents Be sure that these tablets are applicable to the wa ter hardness in your area Refer to the in structions on the packaging of the products Detergent tablets do not fully dissolve with short programmes To prevent detergent residues on the tableware we recommend that you use the tablets with long pro grammes Do not use more than the correct quantity of detergent Refer to the instructions on the detergent packaging www zanussi com First remove the items from the lower bas ket then from the upper basket There can be water on the sides and on the door of the appliance Stainless steel be comes cool more quickly than the dishes Loading the baskets Refer to the supplied leaflet with exam ples of the load of the baskets Only use the appliance to wash items that are dishwasher safe Do not
6. put in the appliance items made of wood horn aluminium pewter and copper Do not put in the appliance items that can absorb water sponges household cloths Remove remaining food from the items To remove easily remaining burned food soak pots and pans in water before you put them in the appliance Put hollow items cups glasses and pans with the opening down Make sure that cutlery and dishes do not bond together Mix spoons with other cut lery Make sure that glasses do not touch other glasses Put the small items in the cutlery basket Put the light items in the upper basket Make sure that they do not move Make sure that the spray arms can move freely before you start a programme Before starting a programme Make sure that The filters are clean and correctly installed The spray arms are not clogged The position of the items in the baskets is correct The programme is applicable for the type of load and for the degree of soil The correct quantity of detergent is used Care and cleaning Warning Before maintenance deactivate the appliance and disconnect the mains plug from the mains socket Dirty filters and clogged spray arms de crease the washing results Make a check regularly and if necessary clean them Cleaning the filters There is dishwasher salt and rinse aid un less you use combi detergent tablets The cap of the sal
7. The released quantity of rinse aid is too much Adjust the rinse aid selector to a low er position The quantity of detergent is too much 11 Stains and dry water drops on glasses and dishes The released quantity of rinse aid is not suf 2 ficient Adjust the rinse aid selector to a higher position 3 The quality of the detergent can be the cause Dishes are wet 4 The programme is without a drying phase or with a low temperature drying phase The rinse aid dispenser is empty The quality of the rinse aid can be the cause The quality of the combi detergent tablets can be the cause Try a different brand or activate the rinse aid dispenser and use rinse aid together with the combi detergent 5 tablets Refer to HINTS AND TIPS for other pos 6 sible causes How to activate the rinse aid dispenser 1 Press the on off button to activate the ap pliance Make sure that the appliance is in Technical information Dimensions Electrical connection Voltage Frequency Water supply pressure Min max bar MPa Water supply 1 Capacity Place settings Left on mode Off mode Power consumption Width Height Depth mm Refer to the rating plate Cold water or hot water2 setting mode refer to Setting and starting a programme Turn the programme knob until the pro gramme marker is aligned with Y Press and hold at the same time Multi tab and Delay un
8. consumption for crockery and cutlery with normal soil This is the standard programme for test institutes 3 The appliance senses the degree of soil and the quantity of items in the baskets It automatically adjusts the temperature and quantity of the water the energy consumption and the programme duration 4 With this programme you can wash a load with fresh soil It gives good washing results in a short time 5 Use this programme to quickly rinse the dishes This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance Do not use detergent with this programme Information for test institutes For all the necessary information for test performance send an email to info test dishwasher production com Write down the product number PNC that is on the rating plate Options Multitab Activate or deactivate the Multitab option before the start of a programme You cannot activate or deactivate this option while a programme operates This option deactivates the flow of rinse aid and salt The related indicators stay off 1 Press Multitab the Multitab indicator comes on The option will stay on until you deacti vate it If you stop to use the combi detergent tablets before you start to use www zanussi com separately detergent rinse aid and dishwasher salt do these steps 1 Set the water softener to the highest level 2 Make sure that the salt container and the
9. g Troubleshooting 11 Technical information Hints and tips __ 222 2 ____ 9 10 12 Environment concerns 13 Subject to change without notice Make sure that the electrical information on the rating plate agrees with the power sup ply lf not contact an electrician Always use a correctly installed shockproof socket Do not use multi plug adapters and exten sion cables Make sure not to cause damage to the mains plug and to the mains cable Contact the service or an electrician to change a damaged mains cable Connect the mains plug to the mains socket only at the end of the installation Make sure that there is access to the mains plug after the installation Do not pull the mains cable to disconnect the appliance Always pull the mains plug Only for UK and Ireland The appliance has a 13 amp mains plug If it is necessary to change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse This appliance complies with the E E C Di rectives Water connection Make sure not to cause damage to the wa ter hoses The appliance is to be connected to the wa ter mains using the new supplied hose sets Old hose sets must not be reused Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean www zanussi com The first time you use the appliance make sure that there is no leakage The appliance can release hot steam
10. if you open the door while a programme operates Do not put flammable products or items that are wet with flammable products in near or Use This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working environments Farm houses By clients in hotels motels and other resi dential type environments Bed and breakfast type environments Warning Risk of injury burns electrical shock or fire Do not change the specification of this ap pliance Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal position Do not keep the appliance door open with out supervision to prevent to fall on it Do not sit or stand on the open door Dishwasher detergents are dangerous Obey the safety instructions on the deter gent packaging Do not drink and play with the water in the appliance Do not remove the dishes from the appli ance until the programme is completed There can be detergent on the dishes www zanussi com on the appliance Do not use water spray and steam to clean the appliance Disposal A Warning Risk of injury or suffocation Disconnect the appliance from the mains supply Cut off the mains cable and discard it Remove the door catch to prevent children and pets to get closed in the appliance Service Contact the Service to repair the appliance We rec
11. least 2 times per month a el The appliance does not drain the wa ter 7 The anti flood device is on Warning Deactivate the appliance before you do the checks You cannot activate the appliance Make sure that the mains plug is connected to the mains The programme does not start The appliance does not fill with water The appliance does not drain the water The anti flood device is on socket Make sure that there is not a damaged fuse in the fuse box Make sure that the appliance door is closed If the delay start is set cancel the setting or wait for the end of the countdown Make sure that the water tap is open Make sure that the pressure of the water supply is not too low For this information contact your local water authority Make sure that the water tap is not clogged Make sure that the filter in the inlet hose is not clogged Make sure that the inlet hose has no kinks or bends Make sure that the sink spigot is not clogged Make sure that the drain hose has no kinks or bends Close the water tap and contact the Service After the checks are completed activate the appliance The programme continues from the point of interruption If the problem occurs again contact the Serv ice If the display shows other alarm codes con tact the Service www zanussi com If the washing and drying results are not satisfactory Whitish streaks or bluish layers on glasses and dishes
12. ommend only the use of original spare parts When you contact the Service ensure that you have the following information that is available on the rating plate Model PNC Serial Number Control panel o vor On off button Start button Programme marker E Delay button Indicators Multitab button Display El Programme knob Co wa DD HHH TT A Washing phase indicator 55 Drying phase indicator Rinse aid indicator This indicator is off while the programme oper ates 6 Salt indicator This indicator is off while the programme operates Multitab indicator Programmes Programme Degree of soil Programme Duration Energy Water 1 Type of load phases min kWh 1 E 2 Normal soil Prewash co Crockery and cut Wash 50 C lery Rinses Dry 4 www zanussi com Programme Degree of soil Programme Duration Energy Water 1 Type of load phases min kWh 0 AUTO All Prewash 40 150 0 6 1 4 8 14 3 Crockery cutlery Wash from 45 C to 70 pots and pans C Rinses Dry Heavy soil Prewash 130 150 1 3 1 4 13 15 Crockery cutlery Wash 70 C pots and pans Rinses Dry Go 4 Fresh soil Wash 60 C 30 0 8 9 Crockery and cut Rinse lery A 5 All Prewash 14 0 1 4 1 The pressure and the temperature of the water the variations of the mains supply the options and the quantity of dishes can change the values 2 With this programme you have the most efficient use of water and energy
13. op a 8 Y fN 156967010 B 332013
14. rinse aid dispenser are full 3 Start the shortest programme with a rins ing phase without detergent and without dishes 4 Adjust the water softener to the water hardness in your area 5 Adjust the released quantity of rinse aid 1 This option is not applicable to 7 Before first use 1 Make sure that the set level of the water softener agrees with the water hardness in your area If not adjust the water softener Contact your local water authority to know the water hardness in your area 2 Fill the salt container 3 Fill the rinse aid dispenser 4 Open the water tap Adjusting the water softener Water hardness German French mmol l degrees degrees CdH CfH 47 50 84 90 8 4 9 0 43 46 76 83 7 6 8 3 37 42 65 75 6 5 7 5 29 36 51 64 5 1 6 4 23 28 40 50 4 0 5 0 19 22 33 39 3 3 3 9 15 18 26 32 2 6 3 2 11 14 19 25 19 25 4 10 7 18 0 7 1 8 lt 4 lt 7 lt 0 7 1 Factory position 2 Do not use salt at this level How to adjust the level of the water softener 1 Press the on off button to activate the ap pliance Make sure that the appliance is in setting mode refer to Setting and starting a programme 2 Turn the programme knob until the pro gramme marker is aligned with 7 3 Press and hold at the same time Multi tab and Delay until the indicators mf 55S start to flash 4 Press Multitab The indicators JS and go off
15. t container is tight To remove filters B and C turn the handle counterclockwise and remove Pull apart filter B and C Wash the filters with water Remove filter A Wash the filter with water Before you put the filter A back make sure that there are no residues of food or soil in or around the edge of the sump Make sure that filter A is correctly positioned under the 2 guides D Assemble filters B and C Put them back in filter A Turn the handle clockwise until it locks An incorrect position of the filters can cause bad washing results and damage to the appliance Cleaning the spray arms Do not remove the spray arms If the holes in the spray arms are clogged re move remaining parts of soil with a thin poin ted object External cleaning Clean the appliance with a moist soft cloth Only use neutral detergents Do not use abra sive products abrasive cleaning pads or sol vents www zanussi com Internal cleaning lf you regularly use short duration pro grammes these can leave deposits of grease and limescale inside the appliance Troubleshooting The appliance does not start or it stops during operation Before you contact the Service refer to the in formation that follows for a solution to the problem With some problems the display shows an alarm code IQ The appliance does not fill with water To prevent this we recommend to run long duration programmes at
16. til the indicators mf SSS and start to flash Press Delay The indicators and i go off The indicator continues to flash The display shows the current setting of the rinse aid dispenser Od Id Press Delay again and again to change the setting Off On Press the on off button to deactivate the appliance and to confirm the setting 600 850 625 220 240 V 50 Hz 0 5 0 05 8 0 8 max 60 C 12 0 99 W 0 10 W 1 Connect the water inlet hose to a water tap with a 3 4 thread 2 If the hot water comes from alternative sources of energy e g solar panels aeolian energy use the hot water supply to decrease energy consumption 12 www zanussi com Rating plate Environment concerns Recycle the materials with the symbol Put appliances marked with the symbol amp with the the packaging in applicable containers to household waste Return the product to your recycle it local recycling facility or contact your Help protect the environment and human municipal office health and to recycle waste of electrical and electronic appliances Do not dispose Discard correctly the packaging material Recycle the materials with the symbol www zanussi com 13 14 www zanussi com www zanussi com 15 www zanussi com sh
Download Pdf Manuals
Related Search