Samsung SC15F50HT
Contents
1. Unplug the cleaner when not in use Turn off the power switch before unplugging Do not use to suck up water Do not immerse in water for cleaning The hose should be checked regularly and must not be used if damaged The vacuum cleaner handle contains electrical connections the handle is not a serviceable part The current carrying hose handle contains electrical connections is not a serviceable part by user Please contact the manufacturer or service center for a replacement UV BRUSH Since the UV rays from the UV Brush damage skin and eyes never allow the rays to make contact with skin or eyes and do not let children or the elderly use the UV Brush It may damage your eyesight 04_ safety information If the transparent window is broken and the UV rays are exposed directly turn the power off and contact the service center Do not use the UV Brush for purposes other than the sterilization of mattresses bedclothes beds cushions and so on made from material The company will not be held liable for any loss due to accidents from using the UV Brush for purposes other than its original purpose as listed above Do not sit on the UV Brush or drop it and avoid imparting impacts on the product Failing to do so may result in injury or product damage Do not touch the power terminals on the back of the UV Brush with a metal pin or rod This may result in electric shock or fire When the UV lamp is out of order never disasse2. 1 ON OFF Button Press the button to operate the vacuum cleaner Press again to stop the vacuum cleaner 2 Suction Button Press the button to operate the vacuum to high suction power Press the button to operate the vacuum to low suction power Handle Control The cleaner is controlled by radio frequency signals If no button is pressed for 30 minutes while cleaning the safety device is activated and the power is cut off In this case press the Power button on the main unit or unplug and then plug the power cord in again 08_ operating the cleaner HOSE SC15F50U SC21F50U Series sender 1 ON OFF Button Press the button to operate the vacuum cleaner Press again to stop the vacuum cleaner 2 SUCTION Button Press the SUCTION button to increase or decrease the suction power Each time you press the button you gradually increase the suction power After the suction power reaches its Handle Control maximum the next time you press the button you return the The cleaner is controlled by radio suction power to its minimum frequency signals 3 BRUSH ON OFF Button Press the BRUSH ON OFF button to operate the UV Brush Press again to stop the UV Brush If no button is pressed for 30 minutes while cleaning the safety device is activated and the power is Cut off In this case press the Power button on the main unit or unplug and then plug the
3. power cord in again YANVSAT10 AHL ONILVdAdO z0 Change the battery e When the vacuum cleaner does not work replace the batteries If the problem persists please contact our authorized dealer e Use 2 batteries of size AAA 1 Never disassemble or recharge the batteries CAUTION 2 Never heat up the batteries or throw them into fire 3 Do not reverse poles 4 Dispose of the batteries property BODY Press the power ON OFF button repeatedly to start and to stop the vacuum cleaner OFF gt ON gt OFF If the remote handle control is not working the cleaner can be operated using the ON OFF button on the body of the machine The ON OFF button operates the vacuum cleanner or stops it The filter light is illuminated when the dust pack requires checking or emptying operating the cleaner _09 operating tne cleaner Body control type SCO7F50V SC15F50V SC21F50V Series HOSE To reduce suction for leaning draperies small rugs and other light fabrics pull the tap air until the hole is open BODY To control power level just slide the power control up and down MIN For delicate fabrics e g net curtains MAX For hard floors and heavily soiled carpets 1 Insert the brush into the hose handle e Insert the UV brush securely into the hose handle until you hear a clicking sound 2 Press the BRUSH ON OFF button to start cleaning e Press the
4. 00 Type General purpose vacuum cleaner 28 m gt 9 1 Indicative annual energy consumption kWh per year based on 50 cleaning tasks Actual annual energy consumption will depend on how the appliance is used 2 Measurements for power consumption and performance are based on methods in EN 60312 1 and EN 60704 PMGMO If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center COUNTRY CUSTOMER CARE CENTER WEB SITE U K 0330 SAMSUNG 7267864 www samsung com SOUTH AFRICA 0860 7267864 SAMSUNG www samsung com DJ68 00699B 08
5. BRUSH ON OFF button and choose the appropriate suction strength for the cleaner e tis advisable to select the Max suction strength setting e UV sterilization cannot be activated by itself 3 When you have finished UV cleaning press the W button e Press the i button to stop the cleaner For safety reasons UV brushing only runs for 30 minutes and then stops operating To resume the operation press the SUCTION button again The UV brush which is inserted into the hose handle not directly connected to the telescopic CAUTION pipe is dedicated for bedclothes 10_ operating the cleaner USING THE DUST SENSOR OPTION Dust Sensor Operations e Indicates the amount of sucked in dust so that users can experience the successful operation of the product while cleaning the room Green When the amount of sucked in dust is small Red When the amount of sucked in dust is large e The dust sensor is automatically turned on when the cleaner runs and turned off when the cleaner is stopped e Since the dust sensor runs on battery power there is no separate switch YANVSAT10 AHL ONILVdAdO z0 Installing the Batteries 2 Check the polarities e fthe dust sensor doesn t work even after cleaning the sensor replace the batteries with new ones AAA type batteries are required e Do not disassemble or recharge the used batteries CAUTIONe Do not heat the batteries or put them in a fire e Che
6. SC07F50 series SC15F50 series SC21F50 series x Before operating this unit please read the instructions carefully English For indoor use only imagine the possibilities Thank you for purchasing a Samsung product TAS aad safety information SAFETY INFORMATION e Before operating the appliance please read this manual thoroughly and retain it for your WARNING reference e Because these following operating instructions cover various models the characteristics of WARNING your vacuum cleaner may differ slightly from those described in this manual CAUTION WARNING SYMBOLS USED Indicates that a danger of death or serious injury exists WARNING Indicates that a risk of personal injury or material damage exists CAUTION OTHER SYMBOLS USED N Represents something you must NOT do Represents something you must follow Indicates that you must disconnect the power plug from the socket This vacuum cleaner is designed for household use only WARNING Do not use this vacuum cleaner to clean building waste and debris Regularly keep the filters in clean conditions to prevent of collecting fine dust in them Do not use this vacuum cleaner with any of the filters removed Failure to meet these requirements could cause damage to the internal parts and void your warranty Notes on the energy label e Declared energy efficiency and cleaning performance class on carpet or in places where the carpet i
7. ck the polarities before inserting the batteries e Put the used batteries into the battery recycle bin e When you are not using the product for an extended period of time remove the batteries operating the cleaner _11 operating tne cleaner Cleaning the dust sensor Option e Since the dust sensor consists of sensitive electronic devices if water or other liquids enters the sensor it may cause a problem e f you use the dust sensor without closing the battery compartment cover pollutants such as dust may accumulate in the compartment and cause a problem Therefore be sure to use the product with the compartment cover closed e Take care when you use the cleaner because the dust sensor may malfunction or may break due to an impact Dust Sensor 2 EA Installing the Dust Sensor e Assemble the dust sensor between the air inlet connector and the extension pipe Recommended You can assemble the dust sensor between the extension pipe and the hose The assembly position of the dust sensor 12 _ operating the cleaner iter and tool maintenance USING ACCESSORY Pipe e Adjust the length of the telescopic pipe by sliding the length control button located in the center of the telescopic pipe back and forth e To check for blockages separate the telescopic pipe and adjust to shorten This allows for easier removal of waste clogging the tube AONVNALNIVN TOOL ANY HY3lld 0 Acces
8. mble or modify the product yourself Please contact the manufacturer or service center for a replacement since an internal discharge occurs within the UV Brush never use the product near an inflammable spray or substance Take care not to touch the UV lamp window after using the UV Brush for an extended period of time as the surface of the window may be hot The UV Brush may start slowly at a low temperature due to the inherent characteristics of UV lamps Please keep the UV Brush indoors safety information _05 contents ASSEMBLING THE CLEANER OPERATING THE CLEANER FILTER AND TOOL MAINTENANCE TROUBLESHOOTING 06_ contents Power cord Power control Using the UV brush SC15F50U SC21F50U Series Using the Dust Sensor Option Using accessory Maintain floor tools Cleaning the Dust Sensor Option Emptying the dust bin Cleaning the dust filter Cleaning the dust filter Cleaning the outlet filter assembling the cleaner e Please do not press the button of dust bin handle when carrying machine e For storage park the floor nozzle OPTION assembling the cleaner _07 YANVATO AHL ONITEWSASSV LO operating tne cleaner POWER CORD e When removing the plug from the electrical outlet grasp the plug not the CAUTION cord POWER CONTROL Radio frequency remote control SC07F50H SC15F50H SC21F50H SC15F50U SC21F50U Series HOSE SC07F50H SC15F50H SC21F50H Series
9. s clogged and clean it if necessary e Empty the dust bin of the cleaner or clean the filters If the red light does not light up when cleaning a dusty location e Clean the sensors 2EA in the dust sensor block with a dry cloth Take care when you clean the sensors in the dust sensor block so that the sensors are not CAUTION damaged 18_ filter and tool maintenance EMPTYING THE DUST BIN Separate the dust bin cover by twisting counter clockwise and pulling the lid Once dust reaches the dust full Take the dust bin out by pushing mark empty the dust bin the button Before use push the dust Close the dust bin by pushing lid bin into the main body of the down and twisting clockwise vacuum cleaner until you hear the click Sound Throw the dust away in the bin e Empty into a plastic bag recommended for asthma allergy sufferers You may rinse the dust bin with cold water filter and tool maintenance _19 JONVNALNIYVIN TOOL ANY HY3Llld 0 iter and tool maintenance CLEANING THE DUST FILTER When to clean the dust filter e The lamp will turn red when suction is reduced If the light comes on please clean the dust filter e Turn the vacuum power to MAX Body Control Handle Control e If the filter check indicator turns red with the inlet floating 10cm above flat floor clean the dust pack When suction is noticeably reduced con
10. s not start e Check cable plug and socket e Leave to cool Suction force is gradually decreasing e Check for blockage and remove Low or decreasing suction e Please check filter and if required clean as illustrated in the instructions if filters are out of condition change them to new ones Cord does not rewind fully e Pull the cord out 2 3 m and push down the cord rewind button Vacuum cleaner dows not pick up dirt e Check hose and replace if required Body overheating e Please check filters if required clean as illustrated in the instruction Static electicity discharge e Please decrease power suction e This can also occur when air in the room is very dry Please ventilate the room to air humidity become a normal This Vacuum cleaner is approved the following Electromagnetic Compatibility Directive 2004 108 EEC Low Voltage Directive 2006 95 EC troubleshooting _23 ONILOOHSATENOUL vo rOduct fiche English According to Commission Regulation EU No 665 2013 and No 666 2013 a Supplier Samsung Electronics Co Ltd 33 Model SC15F50HT SC15F50HU SC15F50UW SC15F50V3 SCO7F50HV SCO7F50HX SCO7F50V3 em Energy Efficiency Class A Annual Energy 4 Consumption kWh yr 8 Carpet Cleaning C Performance Class Hardfloor Cleaning C Performance Class Dust Re Emission Class A Sound Power Level 80 dBA Rated Input Power W 1300 1300 6
11. s used can be met with the enclosed Eco Carpet brush e When the hard floor has joints and gaps please use the enclosed Eco Hard Floor brush which is designed to meet the energy efficiency and cleaning performance class on hard floor with joints and gaps e The values provided on the energy label have been determinded according to the prescribed measuring process in accordance with EN60312 1 Eco Carpet 02_ safety information safety information IMPORTANT SAFEGUARDS GENERAL Read all instructions carefully Before switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate on the bottom of the cleaner WARNING Do not use the vacuum cleaner when rug or floor is wet Close supervision is necessary when any appliance is used by or near children Do not allow the vacuum cleaner to be used as a toy Do not allow the vacuum cleaner to run unattended at any time Use the vacuum cleaner only for its intended use as described in these instructions Do not use the vacuum cleaner without a dust bin Empty the dust bin before it is full in order to maintain the best efficiency Do not use the vacuum cleaner to pick up matches live ashes or cigarette butts Keep the vacuum cleaner away from stoves and other heat sources Heat can deform and discolour the plastic parts of the unit Avoid picking up hard sharp objects with the vacuum cleaner as they ma
12. sory SC07F50H SC15F50H SC21F50H SC15F50V SC21F50V Series e To use the upholstery tool push the accessory on to the end of the hose handle e Pull out the button to use the dusting brush e To use the crevice tool push the accessory on to the end of the hose handle in the opposite direction filter and tool maintenance _13 iter and tool maintenance Accessories SC15F50U SC21F50U Series e Push the accessory onto the end of the hose handle e Pull out the dusting brush to use the crevice tool r j 4r mm A op e Push the accessory onto the end of the pipe e Pull out the dusting brush to use the crevice tool Accessory Option e Furniture brush for desk Furniture and Floor 14 filter and tool maintenance MAINTAIN FLOOR TOOLS 2 Step Brush Carpet Cleaning Floor Cleaning e Adjust the inlet lever according to the floor surface e Remove waste matter completely if the inlet is blocked Power Pet Plus Brush Option AONVNALNIVN TOOL ANY YAlTlsa 0 For improved pickup of pet hair and fibre on carpets Frequent vacuuming of hair or pet fur may cause a reduction in rotation due to matters tangled around the brush roller In this case clean the brush roller with care Push the Open button of the transparent screen cover to separate the cover Remove the brushbar from the transparent screen Remo
13. tinuously or vacuum cleaner abnormally overheats please clean the dust pack 20_ filter and tool maintenance CLEANING THE DUST FILTER Pull the dust bin cover to open To Shake the filter over a garbage can to remove loose dust then wash the filter with cold water Let the filter dry in the shade for more than 12 hours To close the dust bin cover filter should be assembled Close the dust bin cover A Make sure the filter is completely dry before putting it back into the vacuum cleaner Allow 12 hours for it to dry JONVNALNIVIN TOOL ANY HY3lld 0 Put the filter into the dust bin in the correct orientation Before use push the dust bin into the main body of the vacuum cleaner until you hear the click sound filter and tool maintenance _21 iter and tool maintenance CLEANING THE OUTLET FILTER Remove the fixed frame part at the back of the main body Clean the filter By tapping the filters against a hard surface Put the filter and frame part into the main body dust bin e When suction is noticeably reduced continuously or vacuum cleaner abnormally overheats please clean the outlet filter Note Do not wash filter If cleaning does not resolve the problem Please replace blocked out filter e Replacement filters are available at your local Samsung distributor 22_ filter and tool maintenance troubleshooting PROBLEM SOLUTION Motor doe
14. tions 4 Fit Mini turbo brush back together as described in To Replace brush roller instructions 16_ filter and tool maintenance To remove dust from the dust bin of the UV brush SC15F50U SC21F50U Series When you notice that the dust bin is filled use the Dust Removal button to empty the dust bin 1 To remove dust from the dust bin move the Dust Removal button to the Open position While the cleaner is operating Suction use the Dust Removal button for this purpose 2 When done move the Dust Removal button to the Close position When the Dust Removal button is in the Open position the suction power of the cleaner is reduced AONVNALNIVN TOOL ANY dAlTlsa 0 Cleaning the UV brush Cleaning the brush roller SC15F50U SC21F50U Series Human and pet hair often becomes tangled in the brush roller causing a reduction in the rotary power of the the brush roller To prevent this clean the brush roller on a regular basis 1 Push the Open Transparent Cover button inward to remove the cover 2 Use the crevice tool to remove impurities such as dust and hair from around the brush roller 3 When done push the Open Transparent Cover button outward to close the cover filter and tool maintenance _17 maintain tools ana iter CLEANING THE DUST SENSOR OPTION If the green light is not lit while cleaning e Check if the hose extension pipe or the air inlet i
15. ve waste matter such as dust and hair tangled around the brushbar using scissors Remove dust inside the brush housing using a dry duster or crevice tool Insert brushbar into rotating belt and assemble Click the transparent screen cover back into place to reassemble D Ol IY Parquet Master Brush Option e Vacuum dust in wide area at once e Remove waste matter completely if the inlet is blocked filter and tool maintenance _15 iter and tool maintenance Mini turbo brush Option To replace brush roller 1 If a clog is present or debris is visible unscrew the two screws on the back of the Mini turbo brush to remove the faceplate and clear any obstructions 2 Inspect condition of brush roller Replace brush roller if brushes are worn down To remove brush roller pull uo and out of end slots in nozzle housing Insert ends of brush roller into same slots to replace 4 Inspect belt to ensure that it is in good condition If belt is broken or cracked replace belt according to To Replace Belt instructions 3 Using at MAX Press the MAX button to operate the vacuum at maximum intake To replace belt 1 Remove bottom plate See figure in To Replace brush roller instructions 2 Loop one end of new belt around shaft of pulley 3 Loop other end of belt around designated area for it on brushroll Insert brush roller into slots in nozzle housing See figure in To Replace brush roller instruc
16. y damage the cleaner parts Do not stand on the hose assembly Do not put weight on the hose Do not block the suction or the exhaust port Switch the vacuum cleaner off on the body of the machine before unplugging from the electrical outlet Disconnect the plug from the electrical outlet before emptying the dust bin To avoid damage please remove the plug by grasping the plug Itself not by pulling on the cord This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental safety information _03 capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children without supervision Children should be supervised to ensure that they do not play with the appliance The plug must be removed from the socket outlet before cleaning or maintaining the appliance The use of an extension cord is not recommended If your vacuum cleaner is not operating correctly switch off the power supply and consult an authorized service agent If the supply cord is damaged it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard Don t carry the vacuum cleaner by holding the hose Use the handle on the vacuum cleaner set
Download Pdf Manuals
Related Search