Zanussi ZBA32050SA refrigerator
Contents
1. Do not remove nor touch items from the freezer compartment if your hands are damp wet as this could cause skin abrasions or frost freezer burns Avoid prolonged exposure of the appliance to direct sunlight Bulb lamps if foreseen used in this appli ance are special purpose lamps selected for household appliances use only They are not suitable for household room illumination Daily use Do not put hot pot on the plastic parts in the appliance Do not store flammable gas and liquid in the appliance because they may explode www zanussi com Appliance s manufacturers storage recom mendations should be strictly adhered to Re fer to relevant instructions Care and cleaning Before maintenance switch off the appliance and disconnect the mains plug from the mains socket Do not clean the appliance with metal ob jects Regularly examine the drain in the refrigerator for defrosted water If necessary clean the drain If the drain is blocked water will collect in the bottom of the appliance Installation Important For electrical connection carefully follow the instructions given in specific paragraphs Unpack the appliance and check if there are damages on it Do not connect the appliance if it is damaged Report possible damages immediately to the place you bought it In that case retain packing It is advisable to wait at least four hours be fore connecting the appliance to allow t2. min A ka www zanussi com Installing the appliance f Do the following steps Caution Make sure that the mains cable can move freely If necessary cut the adhesive sealing strip and then apply it to the appliance as shown in figure Drill the appliance using a 2 5 mm drill 10 mm max penetration Fix the square fitting to the appliance Install the appliance in the niche Push the appliance in the direction of the arrow 1 until the upper gap cover stops against the 2 kitchen furniture Push the appliance in the direction of the arrow NY 2 against the cupboard on the opposite side of the hinge www zanussi com Adjust the appliance in the niche Make sure that the distance between the appli ance and the cupboard front edge is 44 mm The lower hinge cover in the accessories bag makes sure that the distance between the appli ance and the kitchen furniture is correct Make sure that the clearance between the appli ance and the cupboard is 4 mm Open the door Put the lower hinge cover in po sition Attach the appliance to the niche with 4 screws www zanussi com Remove the correct part from the hinge cover E Make sure to remove the part DX in the case of right hinge SX in opposite case 11 Attach the covers C D to the lugs and the hinge holes Install th
3. rinse and dry thoroughly Important Do not pull move or damage any pipes and or cables inside the cabinet Never use detergents abrasive powders highly perfumed cleaning products or wax polishes to clean the interior as this will damage the surface and leave a strong odour Clean the condenser black grill and the com pressor at the back of the appliance with a brush This operation will improve the perform ance of the appliance and save electricity con sumption Important Take care of not to damage the cooling system Many proprietary kitchen surface cleaners con tain chemicals that can attack damage the plas tics used in this appliance For this reason it is recommended that the outer casing of this ap pliance is only cleaned with warm water with a little washing up liquid added What to do if AN Warning Before troubleshooting disconnect the mains plug from the mains socket Only a qualified electrician or competent person must do the troubleshooting that is not in this manual After cleaning reconnect the equipment to the mains supply Defrosting the refrigerator Frost is automatically eliminated from the evapo rator of the refrigerator compartment every time the motor compressor stops during normal use The defrost water drains out through a drain hole into a special container at the back of the appliance over the motor compressor where it evaporates It is important to peri odi
4. User manual Refrigerator U S R MANUAL ZBA32050SA ZAN USSI Contents Safety instructions Control panel First use gt Daily Us Helpful hints and tips anaak NM A Safety instructions In the interest of your safety and to ensure the correct use before installing and first using the appliance read this user manual carefully in cluding its hints and warnings To avoid unnec essary mistakes and accidents it is important to ensure that all people using the appliance are thoroughly familiar with its operation and safety features Save these instructions and make sure that they remain with the appliance if it is moved or sold so that everyone using it through its life will be properly informed on appliance use and safety For the safety of life and property keep the pre cautions of these user s instructions as the man ufacturer is not responsible for damages caused by omission Children and vulnerable people safety This appliance is not intended for use by per sons including children with reduced physi cal sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction con cerning use of the appliance by a person re sponsible for their safety Children should be supervised to ensure that they do not play with the appliance Keep all packaging well away from children There is risk of suffocation f you are discarding the appliance pull
5. button again The QuickChill indicator will light off Important This function stops automatically after 52 hours www zanussi com First use Cleaning the interior Before using the appliance for the first time wash the interior and all internal accessories with lukewarm water and some neutral soap so Daily use Movable shelves The walls of the re frigerator are equip ped with a series of runners so that the shelves can be posi S tioned as desired Helpful hints and tips Hints for energy saving Do not open the door frequently or leave it open longer than absolutely necessary If the ambient temperature is high and the Temperature Regulator is set to low tempera ture and the appliance is fully loaded the compressor may run continuously causing frost or ice on the evaporator If this happens set the Temperature Regulator toward warm er settings to allow automatic defrosting and so a saving in electricity consumption Hints for fresh food refrigeration To obtain the best performance do not store warm food or evaporating liquids in the refrigerator do cover or wrap the food particularly if it has a strong flavour position food so that air can circulate freely around it www zanussi com as to remove the typical smell of a brand new product then dry thoroughly Important Do not use detergents or abrasive powders as these will damage the finish Positioning the door shelves To
6. the plug out of the socket cut the connection ca ble as close to the appliance as you can and remove the door to prevent playing chil dren to suffer electric shock or to close them selves into it If this appliance featuring magnetic door seals is to replace an older appliance having a spring lock latch on the door or lid be Care and Cleaning ______________ 6 What to do if 6 Installation 8 NOISES 30 Z eta ee et uo 14 Technical data 16 Subject to change without notice sure to make that spring lock unusable before you discard the old appliance This will pre vent it from becoming a death trap for a child General safety A Warning Keep ventilation openings in the appliance en closure or in the built in structure clear of ob struction The appliance is intended for keeping food stuff and or beverages in a normal household and similar applications such as staff kitchen areas in shops offices and other working environments farm houses and by clients in hotels mo tels and other residential type environ ments bed and breakfast type environments catering and similar non retail applications Do not use a mechanical device or any artifi cial means to speed up the thawing process Do not use other electrical appliances such as ice cream makers inside of refrigerating appliances unless they are approved for this purpose by the manufacturer Do not damage the
7. the terminal marked either with the letter E or by the earth symbol or col oured green and yellow 2 Connect the wire coloured blue to the ter minal either marked with the letter N or coloured black 3 Connect the wire coloured brown to the terminal either marked with the L or col oured red 4 Check that no cut or stray strands of wire is present and the cord clamp E is secure over the outer sheath 5 Make sure the electricity supply voltage is the same as that indicated on the appliance rating plate www zanussi com 6 Switch on the appliance The appliance is supplied with a 13 amp plug Door reversibility fitted B In the event of having to change the The door of the appliance opens to the right If fuse in the plug supplied a 13 amp ASTA ap you want to open the door to the left follow proved BS 1362 fuse must be used these steps before you install the appliance Warning A cut off plug inserted into a 13 amp socket is a serious safety shock hazard Ensure that it is disposed of safely fi 1 Loosen and remove the upper pin 2 Remove the door 3 Remove the spacer 4 With a key loosen the lower pin gt NL CEN On the opposite side Tighten the lower pin ooo 2 Install the spacer 3 Install the door 4 Tighten the upper pin Ventilation requirements G N The airflow behind the appliance must be suffi cient Y 5 min YA 200 cm A
8. and by The lamp is defective The temperature is not set correctly The door is not closed correctly The door has been opened too fre quently The product temperature is too high The room temperature is too high During the automatic defrosting process frost defrosts on the rear plate The water outlet is clogged Products prevent that water flows into the water collector The melting water outlet does not flow in the evaporative tray above the compressor The temperature regulator is not set correctly The temperature regulator is not set correctly Switch on the appliance Connect the mains plug to the mains socket correctly Connect a different electrical appli ance to the mains socket Contact a qualified electrician Close and open the door Refer to Replacing the lamp Set a higher temperature Refer to Closing the door Do not keep the door open longer than necessary Let the product temperature de crease to room temperature before storage Decrease the room temperature This is correct Clean the water outlet Make sure that products do not touch the rear plate Attach the melting water outlet to the evaporative tray Set a higher temperature Set a lower temperature 2 If necessary adjust the door Refer to In stallation 3 If necessary replace the defective door device Contact your Service Center Closing the door 1 Cleanthe door gasket
9. cally clean the de frost water drain hole in the middle of the C refrigerator compart ment channel to pre vent the water over flowing and dripping onto the food inside Periods of non operation When the appliance is not in use for long peri ods take the following precautions disconnect the appliance from electrici ty supply remove all food defrost if foreseen and clean the appliance and all accessories leave the door doors ajar to prevent unpleas ant smells If the cabinet will be kept on ask somebody to check it once in a while to prevent the food in side from spoiling in case of a power failure Important There are some sounds during normal use compressor refrigerant circulation www zanussi com ICI IT TI The appliance does not op erate The lamp does not operate The lamp does not work The compressor operates continually Water flows on the rear plate of the refrigerator Water flows into the refrig erator Water flows on the ground The temperature in the ap pliance is too low The temperature in the ap pliance is too high Replacing the lamp The appliance is equipped with a longlife LED interior light Only service is allowed to replace the lighting The appliance is switched off The mains plug is not connected to the mains socket correctly The appliance has no power There is no voltage in the mains socket The lamp is in st
10. e vent grille B Attach the hinge covers E to the hinge Disconnect the parts Ha Hb Hc and Hd 12 Install the part Ha on the inner side of the kitch en furniture www zanussi com P N www zanussi com Push the part Hc on the part Ha Open the appliance door and the kitchen furni ture door at an angle of 90 Insert the small square Hb into guide Ha Put together the appliance door and the furniture door and mark the holes Remove the small squares and drill holes with 2 mm at 8 mm from the outer edge of the door Place the small square on the guide again and fix it with the screws supplied 13 N Align the kitchen furniture door and the appli a ance door by adjusting the part Hb NG J A N Press the part Hd on the part Hb A A Do a final check to make sure that The sealing strip is attached tightly to the cabinet All screws are tightened The door opens and closes correctly There are some sounds during normal running compressor refrigerant circulation 14 www zanussi com www zanussi com Technical data Dimension of the recess Height Width Depth Voltage Frequency The technical information are situated in the rat ing plate on
11. he oil to flow back in the compressor Adequate air circulation should be around the appliance lacking this leads to overheating To achieve sufficient ventilation follow the in structions relevant to installation Wherever possible the back of the product should be against a wall to avoid touching or catching warm parts compressor condens er to prevent possible burn The appliance must not be located close to radiators or cookers Make sure that the mains plug is accessible after the installation of the appliance Connect to potable water supply only If a water connection is foreseen Service Any electrical work required to do the servic ing of the appliance should be carried out by a qualified electrician or competent person This product must be serviced by an author ized Service Centre and only genuine spare parts must be used Environment Protection This appliance does not contain gasses which could damage the ozone layer in ei ther its refrigerant circuit or insulation materials The appliance shall not be discarded together Control panel 2 4 5 6 go Temperature indicator LED Quick Chill indicator Quick Chill button Zia Temperature regulator ON OFF button Switching on Insert the plug into the wall socket Touch the temperature regulator button if all LED are off Switching off Keep touching the temperature regulator but
12. permit storage of food packages of var ious sizes the door shelves can be placed at different heights Gradually pull the shelf in the direction of the arrows until it comes free then re position as required Hints for refrigeration Useful hints Meat all types wrap in polythene bags and place on the glass shelf above the vegetable drawer For safety store in this way only one or two days at the most Cooked foods cold dishes etc these should be covered and may be placed on any shelf Fruit and vegetables these should be thorough ly cleaned and placed in the special drawer s provided Butter and cheese these should be placed in special airtight containers or wrapped in alumi nium foil or polythene bags to exclude as much air as possible Milk bottles these should have a cap and should be stored in the bottle rack on the door Bananas potatoes onions and garlic if not packed must not be kept in the refrigerator Care and Cleaning Caution Unplug the appliance before carrying out any maintenance operation This appliance contains hydrocarbons in its cooling unit maintenance and recharging must therefore only be carried out by authorized technicians Periodic cleaning The equipment has to be cleaned regularly clean the inside and accessories with luke warm water and some neutral soap regularly check the door seals and wipe clean to ensure they are clean and free from debris
13. refrigerant circuit The refrigerant isobutane R600a is con tained within the refrigerant circuit of the ap pliance a natural gas with a high level of envi ronmental compatibility which is nevertheless flammable During transportation and installation of the appliance be certain that none of the compo nents of the refrigerant circuit become dam aged www zanussi com If the refrigerant circuit should become dam aged avoid open flames and sources of ignition thoroughly ventilate the room in which the appliance is situated It is dangerous to alter the specifications or modify this product in any way Any damage to the cord may cause a short circuit fire and or electric shock Warning Any electrical component pow er cord plug compressor must be re placed by a certified service agent or qualified service personnel to avoid hazard 1 Power cord must not be lengthened 2 Make sure that the power plug is not squashed or damaged by the back of the appliance A squashed or damaged pow er plug may overheat and cause a fire 3 Make sure that you can come to the mains plug of the appliance 4 Do not pull the mains cable 5 Ifthe power plug socket is loose do not insert the power plug There is a risk of electric shock or fire 6 You must not operate the appliance with out the lamp cover if foreseen of interior lighting This appliance is heavy Care should be taken when moving it
14. s www zanussi com gaskets Contact the Service Center Installation Caution Read the Safety Information carefully for your safety and correct operation of the appliance before installing the appliance Positioning Warning If you are discarding an old appliance that has a lock or catch on the door you must ensure that it is made unusable to prevent young children being trapped inside Important The appliance shall have the plug accessible after installation Install this appliance at a location where the am bient temperature corresponds to the climate class indicated on the rating plate of the appli ance Climate Ambient temperature class SN 10 C to 32 C N 16 C to 32 C ST 16 C to 38 C T 16 C to 43 C Electrical Connection Caution Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person AN Warning This appliance must be earthed The manufacturer declines any liability should these safety measures not be observed NG Important The wires in the mains lead are coloured in accordance with the following code A Green and Yellow Earth C Brown Live D Blue Neutral As the colours of the wires in the mains lead of this appliance may not correspond with the col oured markings identifying the terminals in your plug proceed as follows 1 Connect the wire coloured green and yel low to
15. the internal left side of the appli ance and in the energy label 16 1780 mm 560 mm 550 mm 230 240 V 50 Hz www zanussi com www zanussi com 17 18 www zanussi com www zanussi com 19 www zanussi com shop GEN ZN fN 222365861 A 102013
16. ton for 3 Sec All indicators light off Temperature regulation To operate the appliance proceed as follows touch the temperature regulator button until the LED corresponding to the required tem with the urban refuse and rubbish The insula tion foam contains flammable gases the appli ance shall be disposed according to the appli cable regulations to obtain from your local au thorities Avoid damaging the cooling unit espe cially at the rear near the heat exchanger The materials used on this appliance marked by the symbol amp are recyclable perature lights up Selection is progressive varying from 2 to 8 C At first button touch actual setting LED keeps blinking Any time the button is touch the set tempera ture is moved to 1 position right Corre sponding LED will blink for a while Touch the setting button until the required temperature is selected The set will be fixed coldest setting 2 C warmest setting 8 C A medium setting is generally the most suitable However the exact setting should be chosen keeping in mind that the temperature inside the appliance depends on room temperature how often the door is opened quantity of food stored appliance location QuickChill function You can activate the QuickChill function by pressing the QuickChill button The LED corresponding to the symbol Quick Chill indicator lights up You can deactivate the QuickChill function by pressing the QuickChill
Download Pdf Manuals
Related Search