Bosch NKN-71022-BA4-10N
Contents
1. Color Connection Green Ground Brown AC Live 24 VAC 230 VAC Blue AC Neutral 24 VAC 230 VAC Table 5 2 Other kits 6 1 Connect the video audio alarm PoE cables as required Tilt or swivel the mount where necessary 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit Installation en 13 5 3 Pulling cables through mount 1 Attach the pink string supplied in Install package to the end of one of the cables protruding out of the base or rear of the housing 2 Feed the pink string with attached cable out through the required opening in the rear or base of the wall mount you can choose the appropriate opening through the wall or in front of the wall See example below for BNC connection and power connections dotted line shows cables fed from rear of housing 3 Use the pink string to pull all other cables through the mount including audio and alarm cables if connected Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 14 en Connecting cables in housing DINION Housing Kit 6 Connecting cables in housing The feed through cables can be fed through the rear or base of the housing depending on customer requirements See the relevant instructions in this section 6 1 Cable and gland requirements Power into the housings must be supplied using type UL Standard SJ cord or better acceptable for outdo2. 7 Configuration and final assembly 7 1 Camera Operation Warning Hazardous voltage Use caution when working inside the housing Hazardous voltage is present in the housing when connected to the AC supply Do not touch the power terminals when the unit is powered Verify operation of the camera and lens before final assembly If necessary adjust the camera orientation focal length and focus refer to the following configuration descriptions for analog and IP cameras Other adjustments Other minor operation adjustments are possible using the camera Menu button these adjustments are described in the camera Operation Guide see Bosch website for applicable camera 7 2 Configuring IP camera kits The camera normally provides an optimal picture without the need for further adjustments however when the kit is mounted and connected the camera field of view and focus point may need to be adjusted To do this 1 Connect a monitor to the CVBS SMB connector on the rear of the camera 2 Start the install wizard Note For ease of connection use the optional NBN MCSMB 30M cable not supplied with Kit to connect a monitor to the camera Install wizard and MENU button on camera The MENU button on the rear panel is used for accessing the camera install wizard The wizard fine tunes the focus and optimizes picture sharpness in both bright and low level lighting for example at night When there is a choice in the wizard the opti
3. 2X Sunshield Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 24 en Maintenance DINION Housing Kit 8 Maintenance No special maintenance is required other than occasionally cleaning the window with water or any non aggressive liquid 81 Fuse replacement 1 Toreplace a fuse push and twist the fuse holder to open it Replace the fuse with a fuse that has the same current rating The fuse is a5 mm x 20 mm slow blow breaking capacity cartridge type fuse 3 Push and twist the fuse holder to close it Housing voltage Fuse rating 24 VAC 4 A 250 VAC 120 VAC 2 A 250 VAC 230 VAC 2 A 250 VAC There is a spare fuse inside the housing 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit Decommissioning en 25 9 Decommissioning The unit should only be passed on together with this installation guide Disposal Your Bosch product was developed and manufactured with high quality material and components that can be recycled and reused This symbol means that electronic and electrical appliances which have reached the end of their working life must be collected and disposed of separately from household waste material Separate collecting systems are usually in place for disused electronic and electrical products Please dispose of these units at an environmentally compatible recycling facility per European Directive 201
4. 1 en System overview System overview These camera kits are complete camera packages that include a camera and lens installed inside a sturdy IP66 proof housing A feed through wall mount is also provided All kits are equipped with a heater blower and a sunshield The maximum camera lens size H x W x D for all models is 91 x 81 x 262 mm 3 6 x 3 2 x10 3 in DINION Housing Kit The kits are available with a choice of input power supply 24 VAC 230 VAC and various connection possibilities housings with feed through fittings in rear and base for power and signal cabling housings with pre wired cables through holes in base of housing housings with rear connectors for a 4 pin power connector and a BNC connector plus an optional feed through fitting for ethernet and other cabling IP camera kits can use the PoE supply if connected to directly power the camera via the Ethernet cable this can be seen as a backup to the normal camera power connection from the housing PCB Available models The following models are available Model Housing input Camera type Connection Pre wired voltage VKC xxx 50 230 VAC DINION AN 4000 Power and BNC No connectors VKN xxx 50 230 VAC DINION AN 5000 Power and BNC No connectors VKC xxx 20 24 VAC DINION AN 4000 Feed through Yes power and video cable VKN xxx 20 24 VAC DINION AN 5000 Feed through Yes power and video cable NKN xxxxx 1
5. 2 Power input grounding post 3 AC power input terminal block connectors 4 AC power output to camera 5 12 VDC power output to camera 6 Fuse Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 18 6 5 en Connecting cables in housing DINION Housing Kit Camera connections Analog camera kit Connect the coax cable with BNC connector directly to the Video connector on the back of the camera If required connect audio and alarm cables directly to back of camera IP camera kit If required connect the Cat5 Cat6 cable to the ETH POE connector on the back of the camera If required connect audio and alarm cables directly to back of camera Use the composite video connector CVBS on the camera to connect an analog monitor for setting up the camera or as a permanent analog output for viewing or recording To connect a monitor for set up use the optional 3 m cable NBN MCSMB 30M to connect directly to the CVBS connector of a monitor Fora permanent analog output use the optional 0 3 m cable NBN MCSMB 03M to connect to a high quality coax cable NBN MCSMB optional 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit 6 6 6 6 1 6 6 2 6 6 3 Connecting cables in housing en 19 Housings with rear connectors Connection Rear housing video connection A BNC connector is provided on the rear of the housing Co
6. Bosch Security Systems DINION Housing Kit Configuration and final assembly en 23 6 Lock the back focus locking button 7 Press and hold the center key for more than 1 second until all the menus disappear 8 Close the side door panel 7 4 Closing the housing Caution Always securely tighten all fittings to ensure a liquid tight seal Failure to do so could allow water to enter the housing and damage the units If a sealant is used ensure that it is a neutral cure type Sealants that release acetic acid may harm electronics Use drip loops on the wiring outside the housing Pull any excess wire out of the housing and tighten the cable glands The tightening force required is approximately 1 to 1 5 turns past the point where the gland starts to grip the wire Failure to correctly tighten the glands could result in water ingress Ensure that all holes are covered with the rubber plugs provided Close the cover and secure the latches Optional tamper resistant screws are provided with the housing If desired secure the latch using these three screws and the provided tamper resistant wrench Close oS 3x 7 5 Positioning sunshield 1 Loosen the two screws M4 x 10 on the top of the housing 2 Slide the sunshield to the desired position It has a range of 50 mm 2 in 3 Tighten the screws to lock the sunshield into position 4 Ifthe sunshield is not installed seal the two screw holes with the plugs supplied
7. IP66 NEMA 4X IP Housing Power Power Power Supply 24 VAC 50 60 Hz Current Consumption 45 W Fuse 4A PoE optional Power over Ethernet connection directly to camera 48 VDC nominal IEEE 802 3af 802 3at Type 1 150 mA 175 mA current consumption 7 2 W 8 4 W power consumption 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit Technical data en 27 Analog Housing Power Power Power input 230 VAC freq 50 Hz consumption 45 W fuse 2 A Power input 24 VAC freq 60 Hz consumption 45 W fuse 4 A Mount LTC 9215 00 Length 300 mm 12 in Maximum Load 9 kg 20 Ib Mounting Head Adjustable 360 pan 180 tilt Finish Light gray Approx Weight 0 4 kg 0 9 Ib Mounting 2 x tapped holes Thread 1 4 20 73 7 mm 2 9 in center spread Camera and lens See the applicable camera and lens documentation for specifications Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 Bosch Security Systems B V Torenallee 49 5617 BA Eindhoven The Netherlands www boschsecurity com Bosch Security Systems B V 2015
8. 0N 24 VAC DINION IP 7000 Power and BNC No connectors M20 fitting for Ethernet cable NKN xxxxx 20N 24 VAC DINION IP 7000 Feed through Yes power cable only 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit Planning information Parts list Planning information en 9 Quantity ltem Material 1 Housing with installed sunshield camera Aluminum and lens 2 Screw 1 4 20 x 0 5 in Stainless Steel 2 Washer spring M6 Stainless Steel 4 Screw tamper resistant M3 5 T15 1 Wrench tamper resistant M3 5 T15 1 Allen key 1 4 20 x 0 5 in 3 Plug installed in fitting in some models MA Silicone 1 Pink string for pulling cables Polyester 1 Feed through wall mount Aluminum 1 Documentation packet Cable fittings for models without pre wiring Quantity ltem Material 2 Cable gland 3 8 in NPT with locking nut Polyamide neoprene 1 Cable gland 1 2 in NPT with locking nut Polyamide neoprene 1 Cable gland M20 x 1 5 Polyamide neoprene Analog models with rear connectors Quantity Item Material 1 4 pin cable connector Female ABS 1 4 pin cable connector Male ABS Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 10 en Planning information DINION Housing Kit 4 2 Unpacking This equipment should be unpacked and handled with care If an it
9. 2 19 EU Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 26 en Technical data 10 Technical data DINION Housing Kit Mechanical Dimensions Hx Wx L closed and including sunshield 126 5 x 171 3 x 480 mm 5 x 6 7 x 18 9 in Weight including camera and lens 3 9 kg 8 6 Ibs Construction Aluminum casing neoprene gaskets all stainless steel hardware 3 3 mm 1 8 in thick glass window Color Gray Locking clasps 3x Tamper resistant screws provided Camera mounting Removable camera lens tray mounted with two screws Max camera lens size H x W x L 91 x 81 x 262 mm 3 6 x 3 2 x 10 3 in Mounting 2 x pair of tapped holes 1 4 20 thread inner pair 50 8 mm 2 0 in center spread outer pair 73 7 mm 2 9 in center spread Rear fittings 20N models 1x cable diameter 3 5 to 8 0 mm 0 14 to 0 32 in 2x cable diameter 5 8 to 10 mm 0 23 to 0 39 in Rear connectors 10N models 1x M20 3 5 to 8 0 mm 0 14 to 0 32 in 1x 4 pin power 1x BNC hybrid analog video Bottom fittings 20N models 2x cable diameter 4 5 to 7 9 mm 0 18 to 0 31 in Environmental Operating Temperature Storage Temperature 40 C to 50 C 40 F to 122 F 40 C to 70 C 40 F to 158 F Operating Humidity 20 to 93 RH Storage Humidity up to 98 RH Enclosure protection
10. DINION Housing Kit VKC 4075 VKN 5085 NKN 710xx BOSCH en Installation Manual DINION Housing Kit Table of contents Table of Contents en 3 1 Safety 4 1 1 Safety message explanation 4 1 2 Safety precautions 4 1 3 Important safety instructions 5 1 4 FCC and ICES compliance 6 1 5 Notices 6 2 Short information 7 3 System overview 8 3 1 Available models 8 4 Planning information 9 4 1 Parts list 9 4 2 Unpacking 10 4 3 Tools required 10 5 Installation 11 5 1 Opening the cover 11 5 2 Install Mount and Housing 12 5 3 Pulling cables through mount 13 6 Connecting cables in housing 14 6 1 Cable and gland requirements 14 6 2 Feed cables through the housing base 14 6 3 Feed cables through the housing rear 15 6 4 Power connections 16 6 4 1 Incoming power safety earth connection 16 6 4 2 Incoming power wires 17 6 5 Camera connections 18 6 6 Housings with rear connectors 19 6 6 1 Connection Rear housing video connection 19 6 6 2 Connection Rear housing power connection 19 6 6 3 Connection rear housing feed through fitting 19 7 Configuration and final assembly 20 CA Camera Operation 20 td Configuring IP camera kits 20 7 3 Configuring analog camera kits 21 7 4 Closing the housing 23 7 5 Positioning sunshield 23 8 Maintenance 24 81 Fuse replacement 24 9 Decommissioning 25 10 Technical data 26 Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 4 en Safety
11. V or an equivalent seal a split rubber sleeve may also be used Tighten the cable glands The tightening force required is approximately 1 to 1 5 turns past the point where the gland starts to grip the wire Failure to correctly tighten the glands could result in water ingress Ensure that all open holes are covered with the rubber plugs provided Replace the camera and tray in the housing if removed Slightly tilt the camera lens tray assembly and slide it in under the rail that is located under the heater on the right side of the housing Lower the tray so that the holes at the side fit over the two screws of the housing Slide the entire assembly forward approximately 5 mm 0 2 in from the front of the window Tighten the two screws to lock the tray in place 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit 6 3 Connecting cables in housing en 15 Feed cables through the housing rear The rear holes allow cable to be fed through the supplied glands or the direct connection of conduit fittings 1 2 Remove the dome plugs located at the rear of the housing Screw the cable glands into the holes at the rear of the housing The holes accept either 3 8 in NPT or 1 2 in NPT cable glands or conduit fittings The M20 x 1 5 cable gland can also be used Feed the power cable through one of the glands Feed the video ethernet cable through a separate
12. ay cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules and ICES 003 of Industry Canada These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and radiates radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his expense Intentional or unintentional modifications not expressly approved by the party responsible for compliance shall not be made Any such modifications could void the user s authority to operate the equipment If necessary the user should consult the dealer or an experienced radio television technician for corrective action The user may find the following booklet prepared by the Federal Communications Commission helpful How to Identify and Resolve Radio TV Interference Problems This booklet is available from the U S Government Printing Office Washington DC 20402 Stock No 004 000 00345 4 1 5 Notices Notice Optical elements are sensitive and should be protected at all times Do not allow objects to come into contact with glass su
13. cable gland To fit the cables through the NPT fitting in the housing Ethernet cable remove the RJ 45 connector and then crimp the connector back on the cable once it is pulled through the gland Crimp in accordance with the connector manufacturer s recommendations the camera connector is Auto MDIX compliant Video cable remove the BNC connector and then crimp the connector back on the cable once it is pulled through the gland Feed any audio and alarm cables through a separate gland as required Apply a seal around the cables in their glands Use RTV or an equivalent seal a split rubber sleeve may also be used Tighten the cable glands The tightening force required is approximately 1 to 1 5 turns past the point where the gland starts to grip the wire Failure to correctly tighten the glands could result in water ingress Ensure that all open holes are covered with the rubber plugs provided Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 16 en Connecting cables in housing DINION Housing Kit 6 4 Power connections Caution To protect the device the branch circuit protection must be secured with a maximum fuse rating of 16A This must be in accordance with NEC 800 CEC Section 60 Caution The external ground wire must always be connected to the main ground post inside the housing 6 4 1 Incoming power safety earth connection Connect the incoming power safety earth wire to th
14. e grounding post on the PCB bracket assembly as follows 1 2 3 4 A terminal lug 4 is provided for connecting the incoming power safety earth wire Remove the nut the washers and the ground wire lug from the grounding post 5 Strip the incoming power safety earth wire and crimp into the lug Reattach the ground connections in the order shown er Nut Lock washer Flat washer gt Ww Input power ground lug Grounding post 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit 6 4 2 Connecting cables in housing en 17 Incoming power wires The terminal block accepts wire ranging from 0 5 mm to 2 5 mm 20 AWG to 14 AWG When using larger wire sizes splice to a smaller size wire at the terminal block end The splice may need to be enclosed in a junction box if it does not pass through the fittings 1 Strip no less than 6 mm 0 25 in and no more than 8 mm 0 31 in of insulation away from the power supply wires Do not nick the wires 2 Connect the incoming power wires to the AC input connectors 3 on the terminal block as shown in the following figure GL O i S OVOP oO SISISIS L N G L N x ee EN ea AC INPUT AC OUT DC12v OUT O IL 6 Callout Function 1 Power cable input to housing G green yellow Earth wire L brown power wire N blue power wire
15. em appears to have been damaged in shipment notify the shipper immediately Verify that all parts are included If any items are missing notify your Bosch Security Systems Sales or Customer Service Representative The original packaging is the safest container in which to transport the unit and can be used if returning the unit for service 4 3 Tools required Small flat blade screwdriver Phillips screwdriver 1 Adjustable wrench Wire cutter stripper crimper tool 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit 5 Installation en 11 Installation Caution Installation should only be performed by qualified service personnel in accordance with the National Electrical Code NEC 800 CEC Section 60 or applicable local codes 5 1 Caution These units must be properly and securely mounted to a supporting structure capable of sustaining the unit weight Use care when selecting mounts or pan tilts not supplied for installation the mounting surface and unit s weight should be carefully considered Opening the cover Caution The heater will be hot when in operation Do not touch Always ensure that the heater is off and cool before working on the camera Open the cover by unlatching the three latches 1 on the side of the housing If the optional tamper resistant screws have been installed use the supplied wrench to remove the screws before o
16. installation of the building If it is needed to open the housing use this all pole switch as the main disconnect device for switching off the voltage to the unit Coax grounding Ground the cable system if connecting an outside cable system to the unit Connect outdoor equipment to the unit s inputs only after this unit has had its grounding plug connected to a grounded outlet or its ground terminal is properly connected to a ground source Disconnect the unit s input connectors from outdoor equipment before disconnecting the grounding plug or grounding terminal Follow proper safety precautions such as grounding for any outdoor device connected to this unit Section 810 of the National Electrical Code ANSI NFPA No 70 provides information regarding proper grounding of the mount and supporting structure grounding of the coax to a discharge unit size of grounding conductors location of discharge unit connection to grounding electrodes and requirements for the grounding electrode Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 6 en Safety DINION Housing Kit 1 4 FCC and ICES compliance FCC amp ICES Information U S A and Canadian Models Only This device complies with part 15 of the FCC Rules Operation is subject to the following conditions this device may not cause harmful interference and this device must accept any interference received including interference that m
17. ion is stored The iris is set to its original value Configuring analog camera kits Connect a service monitor to the Video connector on the back of the camera Check that you can view the camera picture and make the following manual adjustments 1 Turn the focal length lever on the lens to obtain the required field of view 2 Turn the focus lever on the lens to obtain the sharpest image possible Focus Backlight adjustment The camera normally provides an optimal picture without the need for further adjustments however to optimize picture sharpness in both bright and low level lighting use the camera s unique Lens Wizard for back focus This ensures that the object of interest always remains in focus even when focusing at the maximum lens iris opening for example at night Note Always adjust to obtain a sharp picture in both wide angle and tele positions for both far and near focus To adjust back focus 1 Open the slide door panel at the side of the camera Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 22 en Configuration and final assembly DINION Housing Kit 2 Unlock the back focus locking button 3 Press and hold the center key menu button for more than 1 second until the Install menu appears 4 Select Lens Wizard and move cursor to the Set Back Focus Now item 5 Turn the back focus adjustment as required 2014 11 1 0 F 01U 309 609 Installation Manual
18. m DINION Housing Kit Safety Safety message explanation Danger Indicates a hazardous situation which if not avoided will result in death or serious injury Warning Indicates a hazardous situation which if not avoided could result in death or serious injury Caution Indicates a hazardous situation which if not avoided could result in minor or moderate injury Notice Indicates a situation which if not avoided could result in damage to the equipment or environment or data loss a N Safety precautions Warning Hazardous voltage Use caution when working inside the housing Hazardous voltage is present in the housing when connected to the AC supply Do not touch the power terminals when the unit is powered Caution Installation should only be performed by qualified service personnel in accordance with the National Electrical Code NEC 800 CEC Section 60 or applicable local codes Caution This device must be connected to earth ground Safety power ground is indicated by the symbol Caution These units must be properly and securely mounted to a supporting structure capable of sustaining the unit weight Use care when selecting mounts or pan tilts not supplied for installation the mounting surface and unit s weight should be carefully considered PEBBE Ee HD DD Caution To protect the device the branch circuit protection must be secured wi
19. nnect the analog video cable to this connector Connection Rear housing power connection The housings with the rear connectors already mounted are supplied with a 4 pin cable connector for the power cable The 230 VAC models have a male panel connector A female cable connector is provided The 24 VAC models have a female panel connector A male cable connector is provided Mount the 4 pin cable connector onto the power cable 1 Cable diameter must be between 6 mm 0 24 in and 12 mm 0 47 in 2 Strip no less than 6 mm 0 24 in and no more than 8 mm 0 32 in of insulation away from the wire Do not nick the wires 3 Insert the power cord through the back shell assembly and strain relief 4 The cable connector terminals accept wire ranging from 0 75 mm to 2 5 mm 18 AWG to 14 AWG 5 Connect the power input wires to the numbered screw terminals on the mating connector according to the table Connector terminal number Function Wire color 1 AC neutral Blue 2 AC live Brown 3 No Connection do not use 4 Ground Green yellow 6 Assemble the cable connector and plug it into the power receptacle on the housing Connection rear housing feed through fitting Pull cables through this fitting as described in Feed cables through the housing rear page 15 Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 20 en Configuration and final assembly DINION Housing Kit
20. ons are selected by either a short press ora longer press of the MENU button Select EXIT to close the wizard Using Install wizard 1 Power up the camera and wait briefly before opening the camera install wizard 2 Briefly press Menu to start the wizard and display the following screen on the monitor Lens type DC Iris State Ready Focus indicator 8 CONTINUE 180 ROTATE Timeout 300 lt press short gt lt press long gt The lens type is identified and shown on the screen The iris is opened to its maximum value 3 To rotate the image 180 press and hold Menu until the image flips 4 Briefly press Menu to continue 5 Briefly press Menu to center the focus 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit 7 3 Configuration and final assembly en 21 6 Manually adjust the focal length lever on the lens to obtain the required field of view NBN MCSMB optional Zoom Focus T lt gt W co lt gt N 7 Manually adjust the focus lever on the lens to obtain the sharpest image possible 8 Briefly press Menu to start the automatic back focus adjustment AUTO BACK FOCUS The motorized automatic back focus process runs The progress is shown on the monitor 9 Ifthe camera is not in focus press Menu for a longer time to restart the wizard 10 If the camera is correctly focused briefly press the Menu button to exit the wizard The back focus posit
21. or use Installation must conform to NEC 400 4 CEC rule 4 010 and be marked with OUTDOOR W or W A The supplied cable glands have the following specifications Gland type Cable clamping range 3 8 in NPT 4 5 to 7 9 mm 1 2 in NPT 5 8 to 10 mm M20 x 1 5 3 5 to 8 mm 6 2 Feed cables through the housing base To feed cabling through the base of the housing i o RN N 10 dl If required remove the camera and tray to access the holes in the base of the housing loosen the two screws holding the camera tray in the housing Slide the tray backwards and remove from the housing Remove the two dome plugs located at the bottom the housing Screw the two 3 8 in NPT fittings into the foot of the housing Feed the power cable through one of the glands Feed the ethernet video cable through the second cable gland To fit the cables through the NPT fitting in the housing Ethernet cable remove the RJ 45 connector and then crimp the connector back on the cable once it is pulled through the gland Crimp in accordance with the connector manufacturer s recommendations the camera connector is Auto MDIX compliant Video cable remove the BNC connector and then crimp the connector back on the cable once it is pulled through the gland Feed any audio and alarm cables through the second gland as required Pull any excess wire out of the housing Apply a seal around the cables in their glands Use RT
22. pening the latches Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 12 en Installation DINION Housing Kit 5 2 Install Mount and Housing 1 Prepare and secure the wall mount to the mounting surface as described in the LTC 9215 00 Installation Manual included in the Documentation Packet Note If you plan to route cables out the back of the mount ensure that the placement of the mount allows space behind the mounting surface to route and connect wires For housings that are not pre wired connect all required cables to housing PCB and camera see Connecting cables in housing page 14 Position the housing above the mount and feed the protruding cables through the mount as described in Pulling cables through mount page 13 Attach the housing to the mount using the two 2 1 4 20 x 0 5 in screws and washers provided in the mounting kit The spring washers must be used for a secure connection The outermost set of 1 4 20 threaded holes 2 are for mounting to the LTC 9215 00 mount and the innermost 1 4 20 threaded holes 1 are for mounting to all other mounts and pan tilts 5 Connect the power cable to an incoming power supply use wire connectors inside a junction box if necessary to prevent water ingress The wiring color coding for the kits is Color Connection Green Ground White 24 VAC Black 24 VAC Table 5 1 Pre wired 24 VAC kits
23. rfaces and do not touch optical elements with your fingers Notice Video loss is inherent to digital video recording therefore Bosch Security Systems cannot be held liable for any damage that results from missing video information To minimize the risk of losing information we recommend multiple redundant recording systems and a procedure to back up all analog and digital information Notice We recommend that memory cards only be used for local storage of alarm recordings 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit Short information en 7 2 Short information This manual has been compiled with great care and the information it contains has been thoroughly verified The text was correct at the time of printing however the content can change without notice Bosch Security Systems accepts no liability for damage resulting directly or indirectly from faults incompleteness or discrepancies between this manual and the product described Trademarks All hardware and software product names used in this document are likely to be registered trademarks and must be treated accordingly More information For more information please contact the nearest Bosch Security Systems location or visit www boschsecurity com Fa km http www boschsecurity com catalog_overview htm Bosch Security Systems Installation Manual 2014 11 1 0 F 01U 309 609 8 3
24. th a maximum fuse rating of 16A This must be in accordance with NEC 800 CEC Section 60 2014 11 1 0 F 01U 309 609 Installation Manual Bosch Security Systems DINION Housing Kit 1 3 Safety en 5 Important safety instructions Read follow and retain for future reference all of the following safety instructions Follow all warnings before operating the unit 1 Clean only with a dry cloth Do not use liquid cleaners or aerosol cleaners 2 Do not install unit near any heat sources such as radiators heaters stoves or other equipment including amplifiers that produce heat Never spill liquid of any kind on the unit Take precautions to protect the unit from power and lightning surges Adjust only those controls specified in the operating instructions Operate the unit only from the type of power source indicated on the label Unless qualified do not attempt to service a damaged unit yourself Refer all servicing to qualified service personnel 8 Install in accordance with the manufacturer s instructions in accordance with applicable local codes So RW 9 Use only attachments accessories specified by the manufacturer Power disconnect Units have power supplied whenever the power cord is inserted into the power source The power cord is the main power disconnect for all units All pole power switch Incorporate an all pole power switch with a contact separation of at least 3 mm into the electrical
Download Pdf Manuals
Related Search