Franke Swivel Spout
Contents
1. FRANKE CRESTA TAP INSTALLATION INSTRUCTIONS KITCHEN SYSTEMS 237 268 Guarantee Vour Franke mixer has been manufactured to the high standard vou would expect of anv Franke product but in the unlikelv event that vou should experience anv defect in the materials or workmanship within one vear of purchase we will replace the faultv part free of charge This is provided the mixer has only been used for normal domestic purposes in the UK and that the care installation and maintenance instructions have been observed Vou should also retain vour dated invoice as proof of purchase to validate anv claims under our guarantee This one vear guarantee is extended to five vears in the case of the valve mechanism Normal wear and tear is excluded from the guarantee Decorative surface finishes are guaranteed for one vear from the date of purchase provided our advice concerning care has been observed and no scouring agents have been used Scuffs and scratches caused bv improper installation or accidental damage are not covered by this guarantee Neither are slight shade variations or any damage or defect caused by incorrect installation or abuse of the fitting Design This mixer is available in Chrome and SilkSteel to complement all Franke sinks Service For spare parts servicing or any other queries visit www franke co uk Preparation First shut off your water heating2. stop cock close all taps except the new mixer and as the system starts to refill check for leaks Once you have satisfied yourself that there are no leaks switch on the water heating Warning These hints have been prepared for vour guidance vou must exercise due care at all times We do not accept responsibilitv for anv problems that mav occur through incorrect installation How to care for vour kitchen sink mixer To maintain the appearance of this fitting ensure it is cleaned only using a clean soft damp cloth A solution of warm water and mild liquid detergent mav be used where necessarv and then the fitting rinsed thoroughly Abrasive cleaners or acidic cleaners MUST NOT BE USED under any circumstances Avoid contact with all solvents Technical Data Minimum water pressure Maximum water pressure Maximum hot water temperature Recommended hot water temperature 7 25 PSI 0 5 bar 75 PSI 5 bar 70 C 65 C Note If these temperatures or water pressures are exceeded damage to the tap can result A pressure reducing valve may be required to be fitted in high water pressure situations NB If for any reason the spout is removed from the tap care must be taken when reinserting the spout into the body to ensure that the Grub Screw is located in the split of the white PTFE ring 3538R H S PARTS LIST AS FOLLOWS 133 0150 051 133 0150 055 133 0251 364 133 0251 365 _ 133 0251 366 133 0251 368 1 33 0
3. 251 369 133 0251 374 133 0251 375 _ 133 0251 361 133 0258 664 133 0258 665 e 133 0251 367 133 0150 221 ANT ale spo SPOUT SPLASH CHROME UT CHROME O RING KIT MOT COLD 133 0251 370 133 0251 372 FIXIN rg TH CHROME TH SILKSTEEL PLI PLI HANDLE CHROME G KIT CASTEL we n SILKSTEEL i j ee ee o 3 HANDLE CHROME MA MP ab iiacae T HANDLE SILKSTEEL gt HANDLE SILKSTEEL ia ua lai 3472R CH SR 3540R H th kI 3538R C assoni e 3727R l 3311R 3728R Franke UK Limited West Park MIOC Stval Road Manchester M22 5WB Tel 44 0 161 436 6280 Fax 44 0 161 436 2180 Email info uk franke com For spare parts servicing or any other queries visit www franke co uk KITCHEN SYSTEMS
4. system then with your mains stop cock closed open the lowest hot and cold taps in the house and allow to run until the cold storage tank and pipes are empty the hot water storage cylinder always remains full Installation First screw the threaded stud into the mixer body Screw the flexi tails into the mixer body and fully hand tighten After making any necessary alterations to existing pipework pass the plinth over the flexi tails and fit in position The shaped upstand on the plinth will locate in the tap body and the O ring should be placed in the recess to make a seal with the sink When the tap is in position with the cold side on the right when viewed from the front slide the nylon bracing plate up to the underside of the sink together with the retaining plate and secure by screwing the fixing nut finger tight Check that the mixer body and plinth are correctly positioned and fully tighten the fixing nut It is recommended that 15mm x 15mm compression fittings be used to connect mixer to supply pipes Cold is connected to the right and hot on the left when viewed from the front Attention Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove any remaining swarf solder or other impurities Failure to carry out this simple procedure could cause problems or damage to the workings of the mixer Having first checked all new connections turn on the mains
Download Pdf Manuals
Related Search