Horizon DYNC2015 Vehicles battery charger
Contents
1. eaLavay HIST Not to scale Not all wiring shown 3 manana AAAAAAA Not all connectors shown GETTING STARTED CAUTION Never connect the AC and DC input cords to an active power source at the same time This will void the warranty cause product damage and possibly injure the user When Using an External DC Power Source 1 Connect the DC power cord to the charger DC Power Input Port F 2 Connect the DC alligator clips to the DC power source 3 When the charger is powered ON a message will appear on the LCD Screen L NOTICE Always connect cable polarities correctly NOTICE Always consult 12V battery collateral materials or Horizon Hobby before using with sources other than a standard AC wall outlet When Using an External AC Power Source 1 Connect the AC power cord to the charger AC Power Input Port G 2 Connect the AC power cord to the AC power source 3 When the charger is powered ON a message will appear on the LCD Screen L A CAUTION Always power ON the charger before connecting a battery or damage to the charger and the battery can result e Connect the charger to the power source e Select the charging settings e Connect the battery to the charger e Start battery charging PROGRAMMING QUICK GUIDE2. WARRANTY AND SERVICE CONTACT INFORMATION Country of Purchase Horizon Hobby Horizon Service Center Repairs and Repair Requests Horizon Product Support United States of America Product Technical Assistance Contact Information servicecenter horizonhobby com RequestForm www quickbase com db bghj7ey8c a GenNewRecord 888 959 2306 Address 4105 Fieldstone Rd Champaign Illinois 61822 USA Sales sales horizonhobby com 888 959 2306 Service Parts Sales United Kingdom Horizon Hobby Limited sales horizonhobby co uk 44 0 1279 641 097 Units 1 4 Ployters Rd Staple Tye Harlow Essex CM18 7NS United Kingdom Horizon Technischer Service German Y Sales Horizon Hobby GmbH service horizonhobby de 49 0 4121 2655 100 Christian Junge StraBe 1 25337 Elmshorn Germany Service Parts Sales France Horizon Hobby SAS Service Parts Sales Horizon Hobby China infofrance horizonhobby com 33 0 1 60 18 34 90 info horizonhobby com cn 86 021 5180 9868 11 Rue Georges Charpak 77127 Lieusaint France Room 506 No 97 Changshou Rd Shanghai China 200060 FCC INFORMATION Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generat
3. EET THE izon s sole obligation at its option e all Product s involved in Ho hey have replaced w OF LIABILITY EVEN IF HORIZON HAS BEE rther in no event shall the liab on which liabili he Produc setup final assembly modification or misuse no cepted for any res accepts all resulting liability If you as the liabili Product ty associated with the use of the Product immediately in new and unused condition Law These terms are governed by y is asserted As Horizon has no contro iability shall be assumed nor ac ting damage or injury By the act of use setup or assembly the user the purchaser or user are not prepared linois law without regard to conflict of liant with applicable part of the Product iv attempted service by anyone other horized service center v Product not purchased from an echnical regu THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WAR D HEREBY DISCLAIMS ANY AND ALL LIMITATION THE IMPLIED WARRANTIES TNESS FOR A PARTICULAR PURPOSE MPLIED WAR OF NON ALONE HAVE DETERMINED THAT and purchaser s sole ither i service or i hichever is longer SHALL NOT BE LIABLE FOR SPECIAL UENTIAL DAMAGES LOSS COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM EGLIGENCE STRICT LIABILITY OR ANY OTHER OF PROFITS OR PRODU ADVISED OF THE POSS ility of Horizon exceed the purchaser is
4. 13 14 15 Pb 16 I CD CHARGING 17 PB CHARGING 18 PB DISCHARGING USER SETTINGS 19 SAVE DATA 20 LOAD DATA 1 SELF TEST AND PROGRAM SELECT SCREENS ICKEL CADMIUM NI CD BATTERIES CD DISCHARGING NI CD CYCLE CHARGING LEAD ACID SEALED LEAD ACID PB BATTERIES PROGRAM SELECT USER SET LITHIUM BATTERY TYPE LITHIUM BATTERY CHECK TIME NI MH SENSITIVITY PEAK VOLTAGE NI CD SENSITIVITY PEAK VOLTAGE BATTERY CUTOFF TEMPERATURE WASTE BATTERY COOL DOWN TIME SAFETY TIMER BATTERY CAPACITY CUTOFF BEEP AND BUZZER SOUND CONTROL j INPUT POWER LOW VOLTAGE CUTOFF USB DEVICE CHARGING TROUBLESHOOTING se o7anao srd sa r charger to both an AC and a DC power source at the same time When the charger is powered ON there is a series of self tests and the screen will show the charger brand name and model number After self tests the charger shows another screen information may vary From any screen press the Battery Type Memory Button H to go back to the main menu 2 LITHIUM BATTERIES Press the Battery Type Memory Button H to change among the 7 main menu screens and go to the PROGRAM SELECT Lithium BATT screen Press the Select Start Button K to enter this menu This is the menu in which you set the standard Lithium battery charge parameters The Lithium battery type Li Po Li lon or Li Fe chosen at USER SET setup shows on this screen Change Lithium battery type as
5. LITHIUM BATTERIES LI PO PRI Ni MH BATTERIES Ni Cd BATTERIES Pb BATTERIES Press the Battery Type Memory Button H to change among main menu screens or to get to these main menu screens from a submenu screen Press the Select Start Button K to get to submenus for adjusting operating parameters to save value changes or to start chosen battery charging actions Press the Decrease I or Up Buttons J to change between submenu screens or to change Decrease or Increase screen values SAVE DATA LOAD DATA USER SET CAUTION If at any time during the charge process the battery pack s become hot or begin to puff disconnect the battery immediately and discontinue the charge 5 LITHIUM FAST CHARGING process as batteries can cause fire collateral damage and injuries A CAUTION Using a charge rate that is not compatible with the battery capacity may result in damage or malfunction of the charger or battery CAUTION The Lithium charge program menus are to be used ONLY for the charging and discharging of Lithium battery packs Charging other battery types using the Lithium charge programs will damage the battery or the charger 3 LITHIUM CHARGING Press the Battery Type Memory Button H
6. mf L u i Use this menu to adjust peak voltage level D Peak at which the charging stops for a Ni Cd battery pack The D Peak value is adjustable between 5mV Cell and 20mV Cell Generally 10mV Cell is a good choice for Ni Cd batteries When this value is set too high the battery may be over charged When this the value is set too low the charger will not charge a battery to full capacity To select a value other than the default parameter e Press the Select Start Button so the D Peak value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the D Peak value e Press the Select Start Button again to save this value f WASTE BATTERY COOL DOWN TIME Use this menu to set a cutoff temperature that can prevent damage to the battery by stopping the charging process if the battery temperature reaches that limit The charger can be used in conjunction with a battery mounted temperature sensor sold separately DYN5033 connected to the Temperature Sensor Port D to monitor the temperature of the battery during the charging process The temperature can be set between 20 80 C 68 176 F To select a value other than the default parameter e Press the Select Start Button K so the temperature value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the temperature value e Press the Select Start Button again to save this value 2014 Hor
7. until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT Lithium BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the CHARGE screen and set charging parameters The charging amperage A can be set between 0 1 and 6 0A Voltage C is dependent on the number of cells in series B and Lithium battery type 4 LITHIUM BALANCING CHARGING To select values other than the existing parameters e Press the Select Start Button so the charge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the charge current value e Press the Select Start Button again to save the value and the voltage value C flashes e Press the Down Button or Up Button to DECREASE or INCREASE the voltage and of cells in series B e Press the Select Start Button again to save the voltage value If no parameters are flashing you can press the Down Button or Up Button to select another program such as BALANCE FAST CHG STORAGE or DISCHARGE To start charging press and hold the Select Start Button for 3 seconds This program menu is specifically designed for the balanced charging of Lithium batteries including Li Po Li Fe and Li lon battery packs In balance charging each cell in the battery pack is monitored and charged to the same capacity and voltag
8. voltage and of cells in series B e Press the Select Start Button again to save the voltage value If no parameters are flashing you can press the Down Button or Increase Button to select another program such as DISCHARGE To start charging press and hold the Select Start Button for 3 seconds 1 8 PB DISCHARGING h BATTERY CAPACITY CUTOFF A battery pack s capacity can be verified by discharging the pack to its minimum voltage level and measuring the current as the pack is discharged Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT Pb BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the Pb DISCHARGE screen and set discharging parameters The discharging amperage A can be set between 0 1 and 2 0A Voltage C is dependent on the number o and can be set between 2 0 for 1P batteries to 20 0V for 10P batteries cells in series B To select values other than the existing parameters e Press the Select Start Button so the discharge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the discharge current value e Press the Select Start Button again to save the value and the voltage value C flashes e Press the Down Button or Up Button to DECREASE or INCREASE the v
9. Memory Button until you reach the PROGRAM SELECT NiCd BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the NiCd DISCHARGE screen and set discharging parameters The discharging amperage A can be set between 0 1 and 2 0A The discharge level B can be set for AUTO or from 0 1 to 25 0V 1 5 NI CD CYCLE CHARGING To select values other than the existing parameters e Press the Select Start Button so the discharge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the discharge current value e Press the Select Start Button again to save the value and the voltage value B flashes e Press the Down Button or Up Button to DECREASE or INCREASE the voltage e Press the Select Start Button again to save the voltage value If no parameters are flashing you can press the Down Button or Increase Button to select another program such as CHARGE or CYCLE To start discharging press and hold the Select Start Button for 3 seconds The battery can be put through a series of charge discharge cycles using this program Cycling Ni Cd batteries can increase capacity and rejuvenate neglected batteries Discharge capacity and average battery voltage help you compare batteries for the best run time and power Press the Battery Type Memory Button H until you reach the 7 main menus Then press
10. charger switches from Constant Current CC mode to Constant Voltage CV mode to slowly top off the current in the battery pack as close as possible to the maximum capacity In Fast Charge the CV mode is eliminated in order to greatly shorten the charging time however the final capacity of the battery will be less than what you would get using the standard charge method Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT Lithium BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the FAST CHG screen nd set charging parameters The charging amperage A can be set between 0 1 and 6 0A Voltage G is dependent on the number of cells in series B o 6 LITHIUM STORAGE CHARGING If you don t plan on using your battery for a long time it is best to charge or discharge the battery to its optimal storage voltage and capacity These voltage values are different for Li Po 3 85V Li Fe 3 3V and Li lon 3 75V battery packs Using Storage Charging the charger will automatically charge or discharge depend ing on the current charge level the battery to an appropriate level Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT Lithium BATT scre
11. e Press flashes e value l BEEP AND BUZZER SOUND CONTROL he Select Start Button again to save this value he Select Start Button again to save this setting and the time value he Down Button or Up Button to DECREASE or INCREASE the HB Use this menu to set a capacity limit on when the charger stops charging a battery When a charge cycle starts the charger records the battery capacity When the capacity cutoff function is set at ON the charger will stop charging at the capacity limit to prevent battery damage Capacity can be adjusted between 10 and 50 000mAh To select values other than the default parameters e Press the Select Start Button so ON or OFF A flashes e Press the Down Button or Up Button to turn the capacity cutoff ON or OFF e Press the Select Start Button again to save this setting and the capacity value B flashes e Press the Down Button or Up Button to DECREASE or INCREASE capacity value e Press the Select Start Button again to save this value INPUT POWER LOW VOLTAGE CUTOFF Use this menu to set the key beep and charger alarm buzzer at ON or OFF as needed We recommend that you keep the alarm ON so the a charging is complete or if there is cause for alarm during charging To select values other than the default parameters e Press the Select Start Button so ON or OFF A flashes e Press the Down Button or Up Button to set the k
12. needed in the USER SET menu Li V TYPE screen Change other Lithium battery settings as needed in the USER SET menu Refer to the PROGRAM SELECT USER SET section mb et E elo siuna E Press the Down Button I or Up Button J to go to one of the control screens CHARGE BALANCE FAST CHG STORAGE or DISCHARGE to do what your battery needs Correctly connect your lithium battery to the charger charging connector first and balancing connector second Press the Select Start Button K and adjust charging parameters as needed Press and hold the Select Start Button approximately 3 seconds until the screen changes to start the battery check charge sequence When the charge cycle starts the charger compares the battery to charger settings The screen will show battery and your settings information If the information after R charger and S settings A does not match press the Battery Type Memory Button and change the lithium battery charging parameters as needed If the R information matches S press the Select Start Button to confirm After confirmation charging starts and information will show on the LCD screen A A Li Po battery pack is balance charging B Battery pack has 3 cells in series C Charging rate is 2 0A 2000mAh D Voltage being applied to the battery is currently 12 59V E Present charge level of the battery is 1082mAh F Time elapsed since the charge
13. process started is 22 43 22 minutes and 43 seconds During charging the Down Button can be pressed to show several parameter messages on the LCD screen including End Voltage Capacity Cut off Safety Timer setting Temperature Cut off External Temperature and Input Power Voltage Press the Up Button to see charge voltages for each cell and the Down Button to return to the Charge Monitor screen To change the charging rate during charging press the Select Start Button then increase or decrease the rate using the Down Button and Up Button The charger signals when the charging or discharging process is complete if buzzer is set to ON Press the Battery Type Memory Button at any time to stop charging or discharging r ao C D E A Power Output Black B Power Output Red C Balance Circuit Adapter Board Connector D Temperature Sensor Port F DC Power Input Port G AC Power Input Port E 2 1A USB Power Output Port I H Battery Type Memory Button F Down Button J Up Button K Select Select Start Button L LCD Screen
14. replacement plan requires proof of purchase co do reserve full details Contact the appropriate Horizon Service Depart warranty clai 5 YEAR US LIMITED WARRANTY Warranty Period Exclusive Warranty Horizon Hobby abusers of our plan See py of the receipt and we below for ment for instructions on LLC Horizon warrants ded Dynamite Prophet or Passport charger Product will be free from defects in materials and workmanship for a period of five 5 years after the date of purchase Warranty Period What is me Not Covered This warranty is not transferable and does not cover i cos ic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification than a Horizon Hobby authorized Horizon dealer ations Product any and claims THEORY SUCH DAMAGES Fi price of OTHER THA RANTY OR REPRESENTATION Al RANTIES INFRINGEMENT MERCHANTABILITY AND FI THE PURCHASER ACKNOWLEDGES THAT THEY THE PRODUCT WILL SUITABLY NTENDED USE Purchaser s Remedy Ho remedy shall be that Horizon wi are at the sole discretion oi PURCHASER S SOLE AND EXCLUSIVE nder this warranty for thi Period of the Product which Limitation of Liability HORIZO NCIDENTAL OR CONSEQ N CONTRACT WARRANTY TORT of or to any au or vi Product not comp CLUDING WITHOUT
15. the Battery Type Memory Button until you reach the PROGRAM SELECT NiCd BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the NiCd CYCLE screen and set charge discharge cycle count parameters 1 6 LEAD ACID SEALED LEAD ACID PB BATTERIES To select values other than the existing parameters e Press the Select Start Button so the cycle type A flashes e Press the Down Button or Up Button to set the cycle type as CHG gt DCHG or DCHG gt CHG e Press the Select Start Button again to save your choice and the number of cycles B flashes e Press the Down Button or Up Button to DECREASE or INCREASE the cycle count between 1 and 5 e Press the Select Start Button again to save the cycle count value If no parameters are flashing you can press the Down Button or Increase Button to select another program such as CHARGE or DISCHARGE To start cycling press and hold the Select Start Button for 3 seconds Press the Battery Type Memory Button H to change among the 7 main menu screens and go to the PROGRAI ter this menu This is the menu in which you set the standard Pb battery charge parameters The nature of a Lead Acid or Sealed Lead Acid battery is very different from that of Lithium Ni MH or Ni Cd batteries The output current of a Pb battery is lower than other batteries relative to their capacities Furthe
16. value If no parameters are flashing you can press the Down Button or Up Button to select another program such as CHARGE BALANCE FAST CHG or STORAGE To start discharging press and hold the Select Start Button for 3 seconds 8 NICKEL METAL HYDRIDE NI MH BATTERIES Press the Battery Type Memory Button H to change among the 7 main menu screens and go to PROGRAM SELECT Ni MH BATT screen Press the Select Start Button K to enter this menu This is the menu in which you set the standard Ni MH battery charge parameters Change other Ni MH battery settings as needed in the USER SET menu Refer to the PROGRAM SELECT USER SET section Press the Down Button I or Up Button J to go to one of the control screens CHARGE DISCHARGE or CYCLE to do what your battery needs Correctly connect your Ni MH battery to the charger Press the Select Start Button K and adjust charging parameters as needed Press and hold the Select Start Button approximately 3 seconds until the screen changes to start the battery check charge sequence After confirmation charging starts and information will show on the LCD screen A A Ni MH battery pack is charging B Charging rate is 2 0A 2000mAh C Voltage being applied to the battery is currently 7 59V D Present charge level of the battery is 1082mAh E Time elapsed since the charge process started is 22 43 During charging the Down Button or Up B
17. ATE HORIZON SERVICE DEPARTMENT FOR ANY CHARGER WARRANTY CLAIM Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty ser vice will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail pur chase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of 2 hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and Conditions found on our website http www horizonhobby com content _service center_render service center ATTENTION Horizon service is limited to Product compliant in the country of use and ownership If received a non compliant Product will not be ser viced Further the sender will be responsible for arranging re
18. EASE or INCREASE the battery profile value e Press and hold the Select Start Button until the battery charging function screen shows e Press the Down Button or Up Button to go to the charging function you need e Press and hold the Select Start Button to start the chosen charging function Press the Battery Type Memory Button H to change among the 7 main menu screens and go to the USER SET PROGRAM gt screen Use this menu to set up program ming as desired for charging your batteries USER SET programming lets you change from default settings for behind the scenes operating parameters for this charger At the USER SET PROGRAM gt screen press the Select Start Button K to enter the menu Press the Down Button I or Up Button J to change between sub menu screens Press the Battery Type Memory Button to return to the main menu screen a LITHIUM BATTERY TYPE Use this menu to choose lithium battery type Li Po Li lo or Li Fe which shows on other Lithium battery screens e Press the Select Start Button so the voltage value A flashes e Press the Down Button or Up Button to change the voltage value changing voltage value changes lithium battery type 3 7V for Li Po 3 6V for Li lon and 3 3V for Li Fe e Press the Select Start Button to save your selection b LITHIUM BATTERY CHECK TIME Use this menu to set a time limit on a lithium battery check The ba
19. HE PURCHASER S NTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s emedy shall be that Horizon will at its option either i service or ii replace any Product determined by Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement decisions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor ac cepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new a
20. PROPHET PRECEPT 80W LCD AC DC MULTI CHEMISTRY BATTERY CHARGER Ounamee INSTRUCTION MANUAL BEDIENUNGSANLEITUNG MANUEL D UTILISATION MANUALE DI ISTRUZIONI DYNC2015 NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby LLC For up to date product literature visit horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND a little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate thi
21. Support representative Inspection or Services If this Product needs to be inspected or serviced and compliant in the country you live and use the Product in please use the Horizon Onlin Service Request submission process found on our website or call Horizon to obtain Return Merchandise Authorization RMA number Pack the Product securely using shipping carton Please note that original boxes may be included but are not designe to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content _service cen ter_render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping car ton YOU MUST CONTACT THE APPROPRI
22. advised to to the place of purchase REQUIREMENTS OF THE PURCHASER S and exclusive replace any determined by Horizon to be defective Horizon reserves the right to inspect a warranty claim Service or replacement decisions izon Proof of purchase is required for all warranty SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE REMEDY Replacement Products are covered rty 30 days after receipt or for the remainder of the Warranty INDIRECT CTION OR IS BASED BILITY OF individual over use to accept return the aw princi pals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice Questions Assistance and Services Your local hobby store and or place of pur chase cannot provide warranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry at https horizonhobby quickbase com db bghj7ey8c a GenNewRecord or call the toll free telephone num ber referenced in the Warranty and Service Contact Information section to speak with a Product
23. an health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product Revised 07 2014 41026 1
24. ch as DISCHARGE or CYCLE To start charging press and hold the Select Start Button for 3 seconds A battery pack s capacity can be verified by discharging the pack to its minimum voltage level and measuring the current as the pack is discharged Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT NiMH BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the NiMH DISCHARGE screen and set discharging parameters The discharging amperage A can be set between 0 1 and 2 0A The discharge level B can be set for AUTO or from 0 1 to 25 0V 1 1 NI MH CYCLE CHARGING The battery can be put through a series of charge discharge cycles using this program Cycling Ni MH batteries can increase capacity and rejuvenate neglected batteries Discharge capacity and average battery voltage help you compare batteries for the best run time and power Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT NiMH BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the NiMH CYCLE screen and set charge discharge cycle count parameters To select values other than the existing parameters
25. e levels ensuring the optimum performance of the pack Balance charging requires a battery with a balance adapter connector and a balance adapter board that has been designed for your charger and your battery Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRA SELECT Lithium BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the BALANCE screen and set charging parameters The charging amperage A can be set between 0 1 and 6 0A Voltage C is dependent on the number of cells in series B To select values other than the existing parameters e Press the Select Start Button so the charge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the charge current value e Press the Select Start Button again to save the value and the voltage value C flashes e Press the Down Button or Up Button to DECREASE or INCREASE the voltage and of cells in series B e Press the Select Start Button again to save the voltage value If no parameters are flashing you can press the Down Button or Up Button to select another program such as CHARGE FAST CHG STORAGE or DISCHARGE To start charging press and hold the Select Start Button for 3 seconds Near the end of a standard charging cycle the
26. e Press the Select Start Button so the discharge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the discharge current value e Press the Select Start Button again to save the value and the voltage value B flashes e Press the Down Button or Up Button to DECREASE or INCREASE the voltage e Press the Select Start Button again to save the voltage value If no parameters are flashing you can press the Down Button or Increase Button to select another program such as CHARGE or CYCLE To start discharging press and hold the Select Start Button for 3 seconds To select values other than the existing parameters e Press the Select Start Button so the cycle type A flashes e Press the Down Button or Up Button to set the cycle type as CHG gt DCHG or DCHG gt CHG e Press the Select Start Button again to save your choice and the number of cycles B flashes e Press the Down Button or Up Button to DECREASE or INCREASE the cycle count between 1 and 5 e Press the Select Start Button again to save the cycle count value If no parameters are flashing you can press the Down Button or Increase Button to select another program such as CHARGE or DISCHARGE To start cycling press and hold the Select Start Button for 3 seconds 1 2 NICKEL CADMIUM NI CD BATTERIES Press the Battery Type Memory Button H to change among the 7 main menu screens and go
27. en Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the STORAGE screen and set charging parameters The charging amperage A can be set between 0 1 and 6 0A Voltage C is dependent on the number of cells in series B 7 LITHIUM DISCHARGING To select values other than the existing parameters e Press the Select Start Button so the charge c e Press the Down Button or Up Button charge current value e Press the Select Start Button again to save the value and the voltage value C lashes e Press the Down Button or Up Button voltage and of cells in series B e Press the Select Start Button again to save the voltage value If no parameters are flashing you can press the Down Button or Increase Button to select another program such as CHARGE BALANCE STORAGE or DISCHARGE To start charging press and hold the Select Start Button for 3 seconds rrent value A flashes 0 DECREASE or INCREASE the 0 DECREASE or INCREASE the To select values other than the existing parameters e Press the Select Start Button so the charge c e Press the Down Button or Up Button charge current value e Press the Select Start Button again to save the value and the voltage value C flashes e Press the Down Button or Up Button voltage and of cells in series B e Press the Select Start Button again to sa
28. er Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not respon sible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http Avww horizonhobby com content _service center_ren der service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship Li Po batteries to Horizon If you have any issue with a Li Po battery please contact the appropriate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your P
29. es uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications COMPLIANCE INFORMATION FOR THE EUROPEAN UNION C Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2013091205 Product s DYN Prophet Precept 80W LCD AC DC Battery Charger Item Number s DYNC2015EU DYNC2015UK The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the EMC Directive 2004 108 EC and LVD Directive 2006 95 EC EN55022 2010 AC 2011 EN55024 2010 EN61000 3 2 2006 A1 2009 A2 2009 EN61000 3 3 2008 EN60335 1 2002 A11 2004 A1 2004 A12 2006 A2 2006 A13 2008 A14 2010 A15 2011 EN60335 2 29 2004 A2 2010 Signed for and on behalf of Horizon Hobby LLC Champaign IL USA Robert Peak September 12 2013 Chief Financial Officer Horizon Hobby LLC Instructions for disposal of WEEE by users in the European Union Ml fod jee lhis product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects hum
30. ey beep at ON or OFF e Press the Select Start Button again to save this setting and ON or OFF B flashes e Press the Select Start Button again to save this value 22 USB DEVICE CHARGING arm will sound when Press the Down Button or Up Button to set the buzzer at ON or OFF Use this menu to set the input voltage limit so an alarm will sound if the voltage goes below the cutoff value The voltage alarm value can be set from 10 0 to 11 0V To select a value other than the default parameter e Press the Select Start Button so the voltage value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the voltage value e Press the Select Start Button again to save this value The charger has the capability to charge a smartphone music player or any USB compatible device with the 2 1A USB Power Output Port E To use the charging function simply connect a compatible charging device or cord into the charge port while the charger is powered ON The charger provides up to 2 1A current at 5V DC 23 TROUBLESHOOTING Press the Battery Type Memory Button H to change among the 7 main menu screens and go to the PROGRAM SELECT LOAD DATA screen Use this menu to load a saved battery profile 21 PROGRAM SELECT USER SET e Press the Select Start Button K and the battery profile value A flashes e Press the Down Button I or Up Button J to DECR
31. ime to stop charging or discharging CAUTION The Ni Cd charge program menus are to be used ONLY for the charging and discharging of Ni Cd battery packs Charging other battery types using the Ni Cd charge programs will damage the battery or the charger 1 3 NI CD CHARGING Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT NiCd BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the NiCd CHARGE screen and set charging parameters The charging amperage A can be set between 0 1 and 6 0A To select a value other than the existing parameter e Press the Select Start Button so the charge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the charge current value e Press the Select Start Button again to save the value If no parameters are flashing you can press the Down Button or Increase Button to select another program such as DISCHARGE or CYCLE To start charging press and hold the Select Start Button for 3 seconds 1 4 NI CD DISCHARGING A battery pack s capacity can be verified by discharging the pack to its minimum voltage level and measuring the current as the pack is discharged Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type
32. izon Hobby LLC Dynamite Prophet Precept EC3 and the Horizon Hobby logo are tradmarks or registered trademarks of Horizon Hobby LLC Traxxas is a registered trademark of Traxxas L P Use this menu to set waste time during each step in a cycle When a Ni MH or Ni Cd battery is cycled charged discharged and charged again it will get hot therefore it is necessary to set a waste time interval during each step of the process to make sure the battery and charger are completely cooled before moving on to the next part of the cycle Default time is 1 minute but this can be set between 0 and 60 minutes To select a value other than the default parameter e Press the Select Start Button so the time value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the time value e Press the Select Start Button again to save this value are correct for charging arger operation circuits monitor battery and charger functions If the following messages show on the ecommended responses If the message continues after you respond as recommended contact your nearest Horizon Hobby customer is correct between the power source and the charger then between the charger and the battery are no short circuits between the poles of the battery or the battery and the charger Replace damaged wires Input voltage to the charger fell below the default or adjusted input voltage setting Make sure the power
33. nd unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law princi pals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of pur chase cannot provide warranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event sole and exclusive that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry at https horizonhobby quickbase com db bghj7ey8c a GenNewRecord or call the toll free telephone num ber referenced in the Warranty and Service Contact Information section to speak with a Product Support representative Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA numb
34. oltage and of cells in series B e Press the Select Start Button again to save the voltage value If no parameters are flashing you can press the Down Button or Increase Button to select another program such as CHARGE To start discharging press and hold the Select Start Button for 3 seconds Press the Battery Type Memory Button H to change among the 7 main menu screens and go to the PROGRAM SELECT SAVE DATA screen Use this menu to save a battery profile To reduce the time required to initiate a charging or discharging cycle on a battery you regularly use this charger has been designed with the capability of storing up to 5 battery profiles that can be quickly accessed and run using the Load Data menu A e Press the Select Start Button K to enter this menu e Press the Down Button I or Up Button J to select a battery profile A 1 through 5 e Press the Select Start Button to save the battery profile value so the battery ype B flashes e Press the Down Button or Up Button to select a battery type e Press the Select Start Button to save the battery type and the voltage value D flashes e Press the Down Button or Up Button to DECREASE or INCREASE the voltage 20 LOAD DATA e Press the Select Start Button to save the value and the battery capacity C flashes e Press the Down Button or Up Button to DECREASE or INCREASE the battery capaci
35. press the Select Start Button then increase or decrease the rate using the Down Button and Up Button The charger signals when the charging or discharging process is complete if Buzzer is set to ON Press the Battery Type Memory Button at any time to stop charging or discharging CAUTION The Pb charge program menus are to be used ONLY for the charging and discharging of Pb battery packs Charging other battery types using the Pb charge programs will damage the battery or the charger 1 7 PB CHARGING Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT Pb BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the Po CHARGE screen and set charging parameters The charging amperage A can be set between 0 1 and 6 0A Voltage C is dependent on the number of cells in series B and can be set between 2 0 for 1P batteries to 20 0V for 10P batteries To select values other than the existing parameters e Press the Select Start Button so the charge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the charge current value e Press the Select Start Button again to save the value and the voltage value C flashes e Press the Down Button or Up Button to DECREASE or INCREASE the
36. rmore lead acid batteries can t be charged at a level greater than 1 10 their capacity For example a 5000mAh lead acid battery can t be charged at a rate greater than 0 5A For more details on the charge and discharge capabilities of your battery please refer to the charging data supplied by the battery manufacturer Press the Down Button I or Up Button J to go to one of the control screens CHARGE or DISCHARGE to do what your battery needs Correctly connect your Pb battery to the charger Press the Select Start Button K and adjust charg ing parameters as needed Press and hold the Select Start Button approximately 3 seconds until the screen changes to start the battery check charge sequence After confirmation charging starts and information will show on the LCD screen SELECT Pb BATT screen Press the Select Start Button K to en A A Pb battery pack is charging B Battery pack has 6 cells in series C Charging rate is 4 0A 4000mAh D Voltage being applied to the battery is currently 12 39V E Present charge level of the battery is 1082mAh F Time elapsed since the charge process started is 22 43 During charging the Down Button or Up Button can be pressed to show several parameter messages on the LCD screen including End Voltage Capacity Cut off Safety Timer setting Temperature Cut off External Temperature and Input Power Voltage To change the charging rate during charging
37. roduct will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service es timates will be billed a minimum of hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and Conditions found on our website http www horizonhobby com content _service center_render service center ATTENTION Horizon service is limited to Product compliant in the country of use and ownership If received a non compliant Product will not be ser viced Further the sender will be responsible for arranging return shipment of the un serviced Product through a carrier of the sender s choice and at the sender s expense Horizon will hold non compliant Product for a period of 60 days from notification after which it will be discarded
38. s e Always charge in a well ventilated area e Always terminate all processes and contact Horizon Hobby if the product malfunctions WARNING Never leave charger unattended exceed maximum charge rate charge with non approved batteries or charge batteries in the wrong mode Failure to comply may result in excessive heat fire and serious injury use with this type of charger CAUTION Always ensure the battery you are charging meets the specifications of this charger and that the charger settings are correct Not doing so can result in excessive heat and other related product malfunctions which can lead to user injury or property damage Please contact Horizon Hobby or an authorized retailer with compatibility questions SPECIFICATIONS AC Input Voltage 100 240V AC 60 60HZ 11 18V DC 0 1A to 6 0A in 0 1A increments 80W maximum 0 10 to 2 0A in 0 1A increments 10W maximum 0 C to 50 C 300mA per cell Ni Cd Ni MH Peak Li Po Li lon Li Fe Pb CC CV DC Input Voltage Charge Current Discharge Current Operating Temperature Balance Current Drain Charging Mode OPERATING YOUR CHARGER TABLE OF CONTENTS 1 SELF TEST AND PROGRAM SELECT SCREENS LITHIUM LITHIUM BATTERIES LITHIUM CHARGING LITHIUM BALANCING CHARGING LITHIUM FAST CHARGING LITHIUM STORAGE CHARGING LITHIUM DISCHARGING Ni MH 8 NICKEL METAL HYDRIDE NI MH BATTERIES 9 NI MH CHARGING 10 NI MH DISCHARGING 11 NI MH CYCLE CHARGING
39. s Product in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not attempt disassembly use with incompatible components or augment product in any way without the approval of Horizon Hobby LLC This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy This appliance is not intended for use by persons with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety y Included Items JST_XH Balance adapter Banana plug to EC3 battery connector AC power cord one region US EU AU or UK OPTIONAL ACCESSORIES DYN4012 DC Power Cord DYN5006 Charge Adapter Banana to Deans Male DYN5014 Charge Adapter Banana to Traxxas Male DYN5033 Temperature Sensor SAFETY PRECAUTIONS AND WARNINGS WARNING Failure to exercise caution while using this product and comply with the following warnings could result in product malfunction electrical issues excessive heat FIRE and ultimately injur
40. source for the charger provides correct series count pack voltage of a lithium battery Make charger settings match the battery pack label cell in series count lower than the value setting in the charger Adjust settings then make sure the battery is not damaged or replace the battery LCD Screen Warning and Error messages shown below During ch charger s LCD screen make the service center for assistance REVERSE POLARITY Make sure each connection polari CONNECTION BREAK Make sure the power connections SHORT ERR Make sure there MPUTUOLIERR input voltage VOL SELECT ERR Incorrect setting for cell in specifications or replace the battery BREAK DOWN Charger electronics require repair BATTERY CHECK LOW VOLTAGE Battery voltage is BATTERY CHECK HIGH VOLTAGE Battery voltage is higher than the value setting in the charger Adjust settings then make sure the battery is not damaged or replace the battery Battery Type Li Po Li lo Li Fe Ni MH Ni Cd Pb Standard voltage Volts per cell 3 70 3 60 3 30 1 20 1 20 2 00 Max voltage Volts per cell 4 20 4 10 3 60 1 60 1 60 2 45 Min voltage Volts per cell 3 00 3 00 2 00 1 00 0 85 5 DYNAMITE 5 YEAR US LIMITED CHARGER WARRANTY INFORMATION WARRANTY SERVICES We are so confident about the quality of our chargers we offer a 5 year replacement plan on all o that the he right to deny replacement to any ms incl our Dynamite Prophet and Passport chargers Our 5 year
41. to the PROGRAM SELECT Ni Cd BATT screen Press the Select Start Button K to enter this menu This is the menu in which you set the standard Ni Cd battery charge parameters Change other Ni Cd battery charging settings as needed in the USER SET menu Refer to the PROGRAM SELECT USER SET section Press the Down Button I or Up Button J to go to one of the control screens CHARGE DISCHARGE or CYCLE to do what your battery needs Correctly connect your Ni Cd battery to the charger Press the Select Start Button K and adjust charging parameters as needed Press and hold the Select Start Button approximately 3 seconds until the screen changes to start the battery check charge sequence After confirmation charging starts and information will show on the LCD screen A A Ni Cd battery pack is charging B Charging rate is 2 0A 2000mAh C Voltage being applied to the battery is currently 7 59V D Present charge level of the battery is 1082mAh E Time elapsed since the charge process started is 22 43 During charging the Down Button or Up Button can be pressed to show several parameter messages on the LCD screen including Ni Cd Sensitivity Capacity Cut off Safety Timer setting Temperature Cut off External Temperature and Input Power Voltage The charger signals when the charging or discharging process is complete if Buzzer is set to ON Press the Battery Type Memory Button at any t
42. ttery charger can automatically identify the number of series cells in a lithium battery pack Normally this checking process is very quick however it will not work properly if the battery pack is damaged or over discharged Very large capacity packs will also take longer to check To prevent errors the charger default is to spend up to 10 minutes to identify the number of cells Time limit can be between 5 and 60 minutes To select a value other than the default parameter e Press the Select Start Button so the time value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the time value e Press the Select Start Button again to save this value C NI MH SENSITIVITY PEAK VOLTAGE Use this menu to adjust the peak voltage level D Peak at which charging stops for a Ni MH battery pack The D Peak value is adjustable between 5mV Cell and 20mV Cell Generally 8mV Cell is a good choice for Ni MH batteries When this value is set too high a battery may be over charged When this value is set too low the charger will not charge a battery to full capacity To select a value other than the default parameter e Press the Select Start Button so the D Peak value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the D peak value e Press the Select Start Button again to save this value e BATTERY CUTOFF TEMPERATURE d NI CD SENSITIVITY PEAK VOLTAGE
43. turn shipment of the un serviced Product through a carrier of the sender s choice and at the sender s expense Horizon will hold non compliant Product for a period of 60 days from notification after which it will be discarded aooo NON US LIMITED WARRANTY What this Warranty Covers Horizon Hobby LLC Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in ma terials and workmanship at the date of purchase What is Not Covered This warranty is not transferable and does not cover i cos metic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other han a Horizon Hobby authorized service center v Product not purchased from an authorized Horizon dealer or vi Product not compliant with applicable technical regu lations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WAR RANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WAR RANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF T
44. ty e Press the Select Start Button to save the value and the battery profile value flashes e Press and hold the Select Start Button for at 3 seconds until the screen changes to the CHARGE menu e Press the Select Start Button to set the CHARGE parameters Refer to the bat tery type parameter setting instructions e Press the Down Button or Up Button to go to and set other parameters BALANCE CHARGE DISCHARGE etc After setting all parameters press and hold the Select Start Button for 3 seconds until the screen changes After the battery profile has been saved the charger will return to the PROGRAM SELECT SAVE DATA screen Enter the Save Data menu and create more battery profiles or press the Battery Type Memory Button to go to other options g SAFETY TIMER A i Pep B Use this menu to set a time limit for charging a battery When a charge cycle is started a clock inside the charger will begin recording the elapsed charge time If the safety timer function has been turned ON the charger will stop the charging process once this time limit has been reached to avoid damage caused by over charging the battery This time value can be set between 10 and 720 minutes To select values other than the default parameters e Press he Select Start Button so ON or OFF A flashes e Press the Down Button or Up Button to turn the safety timer ON or OFF e Press B e Press tim
45. utton can be pressed to show several parameter messages on the LCD screen including Ni MH Sensitivity Capacity Cut off Safety Timer setting Temperature Cut off External Temperature and Input Power Voltage The charger signals when the charging or discharging process is complete if Buzzer is set to ON Press the Battery Type Memory Button at any time to stop charging or discharging CAUTION The Ni MH charge program menus are to be used ONLY for the charging and discharging of Ni MH battery packs Charging other battery types using the Ni MH charge programs will damage the battery or the charger 9 NI MH CHARGING Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT NiMH BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the NiMH CHARGE screen and set charging parameters The charging amperage A can be set between 0 1 and 6 0A 1 0 NI MH DISCHARGING To select a value other than the existing parameter e Press the Select Start Button so the charge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the charge current value e Press the Select Start Button again to save the value If no parameters are flashing you can press the Down Button or Increase Button to select another program su
46. ve the voltage value If no parameters are flashing you can press the Down Button or Up Button to select another program such as CHARGE BALANCE FAST CHG or DISCHARGE To start charging press and hold the Select Start Button for 3 seconds rrent value A flashes o DECREASE or INCREASE the 0 DECREASE or INCREASE the A battery pack s capacity can be verified by discharging the pack to its minimum voltage level and measuring the current as the pack is discharged Press the Battery Type Memory Button H until you reach the 7 main menus Then press the Battery Type Memory Button until you reach the PROGRAM SELECT Lithium BATT screen Press the Select Start Button K to enter this menu Press the Down Button I or Up Button J to reach the DISCHARGE screen and set discharging parameters The discharging amperage A can be set between 0 1 and 2 0A Voltage C is dependent on the number of cells in series B To select values other than the existing parameters e Press the Select Start Button so the discharge current value A flashes e Press the Down Button or Up Button to DECREASE or INCREASE the discharge current value e Press the Select Start Button again to save the value and the voltage value C lashes e Press the Down Button or Up Button to DECREASE or INCREASE the voltage and of cells in series B e Press the Select Start Button again to save the voltage
47. y and property damage ever leave the power supply charger and battery unattended during use ever attempt to charge dead damaged or wet battery packs ever attempt to charge a battery pack containing different types of batteries ever allow children under 14 years of age to charge battery packs ever charge batteries in extremely hot or cold places or place in direct sunlight ever charge a battery if the cable has been pinched or shorted ever connect the charger if the power cable has been pinched or shorted ever connect the charger to an automobile 12V battery while the vehicle is run ning ever attempt to dismantle the charger or use a damaged charger Never attach yo Never connect the input jack DC input to AC power Always use only rechargeable batteries designed foi Always inspect the battery before charging Always keep the battery away from any material that could be affected by heat Always monitor the charging area and have a fire extinguisher available at all times Always end the charging process if the battery becomes hot to the touch or starts to change form swell during the charge process e Always connect the charge cable to the charger first then connect the battery to avoid short circuit between the charge leads Reverse the sequence when disconnecting e Always connect the positive red leads and negative black leads correctly e Always disconnect the battery after charging and let the charger cool between charge
Download Pdf Manuals
Related Search