Home
Remington IPL6250
Contents
1. REMINGTON IPL6250 SKIN CHART THE SKIN CHART Hair Colour A Age MAREAS ES v lt iy 7 wie te tw WARNING i LIGHT is not suitable for very dark or black skin white grey or very light blonde red hair 9 0 O ES Z 197 DO NOT use on or around the eyes eyebrows or eyelashes Doing so can cause serious and permanent eye injury Thank you for buying your new Remington product Please read these instructions carefully and keep them safe Remove all packaging before use IMPORTANT SAFETY INSTRUCTIONS WARNING TO REDUCE THE RISK OF BURNS ELECTROCUTION FIRE OR INJURY TO PERSONS Use this appliance only for its intended use described in this manual Do not use if it is damaged or malfunctions Do not leave the appliance unattended while plugged in Keep the power plug and cord away from heated surfaces Do not use the product with a damaged cord A replacement can be obtained via our International Service Centres Store the product at a temperature between 15 and 35 C Only use the parts supplied with the appliance Do not twist or kink the cable and don t wrap it around the appliance 10 The body of this appliance is not washable or water resistant Do not put the appliance in liquid do not use it near water in a bath tub basin or other vessel and don t use it outdoors NX 11 Make sure the power cable and adaptor do not get wet Do not reach for your unit if
2. A i LIGHT is designed for unisex use on areas below the neck including the legs underarms bikini line arms chest and back What are the risks involved with i LIGHT Is it safe i LIGHT is clinically proven to be safe amp effective but like any electronic device it is important that you read and follow the operating instructions and safety warnings Is IPL dangerous for the skin after long term use There have not been any reported side effects or skin damage from long term use of intense pulse light IPL Q Why is my hair growing despite treatments A Results aren t immediate and individual results vary Most users will begin to notice fewer hairs within 1 2 weeks after beginning treatment During this time it may look like the hair is still growing but it is actually being pushed out Hair grows in a cycle of 3 different phases which lasts 18 24 months Only hairs in the active growth phase are susceptible to treatment which is why multiple treatments are required for optimal result Another reason for continued growth could be that the area was missed during a treatment Repeat the treatment regime when you notice regrowth Why can t use i LIGHT after recent sun exposure Sun exposure causes high levels of melanin to be present and exposes the skin to higher risk of burns or blisters following treatment gt O O gt O 2 gt O Q Do need eye protection while using i LIGHT A No it is
3. Remington Consumer Products Unit B12 Ballymount Corporate Park Ballymount Dublin 12 www remington co uk Model No IPL6250 14 UK IPL6250 T22 0002737 Version 08 14 Remington is a Registered Trade Mark of Spectrum Brands Inc or one of its subsidiaries Spectrum Brands UK Ltd Fir Street Failsworth Manchester M35 OHS www remington co uk
4. This helps prevent exposure to more energy than is necessary to suppress hair growth It also ensures that you get the maximum use of the Bulb For the most effective results always use the highest intensity level that does not cause discomfort on the skin The level you use should feel warm on your skin but should never cause discomfort You may notice that bony areas such as elbows shins and ankles are more sensitive during treatment This is normal and should not be cause for alarm To avoid this sensitivity try stretching the skin away from the bony area during treatment amp POST TREATMENT CARE After treatment you may experience slight redness or a warm sensation on your skin This is normal and will disappear quickly To avoid irritation to your skin after a treatment take the following precautions Avoid sun exposure for 24 hours after a treatment Protect the skin with SPF 30 for 2 weeks after each treatment Do not prolong sun exposure such as sunbathing using a tanning bed or self tan for at least 2 weeks after the last treatment After treatment keep the area clean and dry and drink plenty of water to keep skin hydrated Do not take hot baths showers or use steam rooms and saunas for 24 hours after treatment Do not take part in contact sports for 24 hours after treatment Do not depilate waxing plucking threading or creams during the treatment shaving is acceptable as long as you avoid shaving 24 hours after
5. not harmful to the eyes i LIGHT features a safety system which prevents unintentional flashing when the device is not in contact with the skin The small amount of light emitted during treatment is similar to that of a camera flash and is not harmful to the eyes ENVIRONMENTAL PROTECTION To avoid environmental and health problems due to hazardous substances in electrical and electronic goods appliances marked with this symbol must not be disposed of with unsorted municipal waste but recovered reused or recycled gt SERVICE AND GUARANTEE_____________ Defects affecting product functionality appearing within the guarantee period will be corrected by replacement or repair at our option provided the product is used and maintained in accordance with the instructions Defects from repair by an unauthorized dealer are not covered Consumables are excluded Your statutory rights are not affected If you call the Service Centre please have the Model No to hand as we won t be able to help you without it The Model No can be found on the rating plate of the appliance Replacement parts and accessories are available to buy at www remington co uk parts accessories gt SERVICE CENTRE United Kingdom AA Tel 0800 212 438 free call mainland UK 44 161 947 3111 call outside the UK Spectrum Brands UK Ltd Fir Street Failsworth Manchester M35 OHS UK www remington co uk Ireland A Tel 142 951 40
6. Sensor is in full contact with the skin Try resetting the unit by turning it off and waiting several seconds before turning it back on 3 There is a strange smell Be sure the area is completely shaved before treatment 3 The treated areas become red after treatment This is normal and the redness should subside If not try using a lower energy level 3 BE AWARE If the unit is used over an extended period of time the unit might automatically disable momentarily estimated 40 seconds to cool down Once the unit has cooled down it will be ready to use again All currently selected energy level Unit is overheated and is disabled indicators flashing momentarily to cool down D 64 All energy level indicators Unit is malfunctioning Turn the flashing unit off wait a few moments and try again If problem persists the gt unit should be returned for repair All LED s flashing with warning Treatment head is removed or beep loose 3 Not full contact Flash button was pressed while the skin contact sensor was not fully engaged Replace bulb Bulb is missing or needs to be replaced Skin contact sensors stuck Flash button was pressed after the skin contact sensor had been engaged since unit start up Skin contact sensor may be stuck ad FREQUENTLY ASKED QUESTIONS For a full list of FAQs please visit www remington ilight com What areas of my body can treat with i LIGHT
7. are susceptible to treatment which is why multiple treatments are required for optimal results Fig 3 Active Growth Anagen Phase Catagen Phase Telogen Phase It s important to continue with the full treatment regime and top up treatments to ensure that every active hair is treated 3 Treatment Regime A full treatment regime is once every two weeks for three treatments Individual results may vary so multiple treatments may be required for optimal results Some hair growth will occur that is less dense finer and lighter in colour than the original hair This regrowth is perfectly normal and should be expected After completing the initial treatment regime top up treatments will provide even better results Continuous regular weekly use will give good results within 6 12 weeks darker skin tones may take longer 3 NOTE You should avoid treating the same area multiple times in one session as it will not improve efficacy but increases the risk of skin irritation WARNINGS AND SAFETY PRECAUTIONS IMPORTANT SAFETY CAUTIONS Before you start using i LIGHT Be sure to read all Warnings and Safety Information Before you begin check to see if i LIGHT is suitable for you Use the skin and hair chart at the front of this manual and the integrated skin sensor to determine if this device is right for you Consult the hair chart at the front of this manual to ensure the device is right for you 3 Skin Type e Do not use
8. d to activate a flash Sj r w 3 Skin Tone Sensor Will only allow usage on suitable skin tones CHECK YOUR SKIN TONE Consult the skin and hair chart at the front of this manual to ensure your skin is in the suitable range and your hair colour is susceptible to treatment with i LIGHT Place the skin of your intended treatment area onto the skin sensor ensure the skin is touching the sensor Fig 4 If your skin is suitable you will hear a beep and the i LIGHT will switch on If your skin is unsuitable you will hear a buzz and the i LIGHT will remain switched off NOTE You must use the skin sensor on each body part you wish to treat a REMINGTON Dstt 3c PREPARE YOUR SKIN FOR TREATMENT Ensure the area to be treated is clean and free from oils deodorants perfume make up lotions and creams Shave the hair from the area to be treated and ensure the skin is clean and dry Never use wax epilation tweezers or other methods that remove the hair from the root as IPL is not effective if the hair has been pulled out 3 PREPARE THE i LIGHT FOR USE Unwrap the hand piece cord from the i LIGHT base and rest the hand piece back on the base unit Ensure the power switch on the base unit is OFF Connect the power cord to the i LIGHT base unit at the power inlet Connect the power cord to the wall outlet Turn the power switch ON fig 5 3c SELECTING THE ENERGY LEVEL The i LIGHT is equip
9. each treatment Do not use bleaching creams or perfumed products for 24 hours after treatment INFINITY BULB 3 Signs that the bulb needs replacing The infinity bulb means no replacement parts are needed The bulb in this device is guaranteed to last for the entire guarantee period as communicated on the guarantee card supplied with this product In the extremely unlikely event that your bulb becomes empty please contact your local Remington Service centre who will provide you with a replacement Bulb Status Indicator is illuminated yellow 150 Flashes remain in the bulb Bulb status indicator is flashing yellow Bulb is empty CLEANING YOUR i LIGHT DEVICE CAUTION Before cleaning your i LIGHT make sure that the device is switched OFF and the power cord is disconnected from the device Regular cleaning helps to ensure optimal results and a long life for the i LIGHT device To clean the Flash Window use only the lint free cloth included with your i LIGHT device Take care not to scratch or chip the Flash Window Scratches and chips can reduce the effectiveness of the unit For stubborn stains on the flash window dampen a cotton swab with surgical spirit or rubbing alcohol apply to the flash window and clean gently with the lint free cloth provided Use a small hand held vacuum to remove dust and debris from the hand piece vents WARNING If the Flash Window is cracked or broken the unit must not be used Never scratc
10. h the filter glass or the metallic surface inside the Treatment Head CAUTION The i LIGHT is a high voltage device Never immerse in water Never clean the unit or any of its parts under a tap or in a dishwasher 3 Storage Switch off the unit unplug and allow to cool for 10 minutes before storage Store the unit in a dry place at a temperature between 15 C and 35 C 2 TROUBLESHOOTING Always read these instructions fully before using i LIGHT Refer to this troubleshooting guide if you experience any problems with i LIGHT as this section addresses the most common problems you could encounter with i LIGHT If you have followed the instructions in this section and continue to experience problems please contact the Remington Service Centre for further assistance 3 The power switch is ON but the unit is not working Make sure the unit is plugged into a working electrical outlet Try switching to a different outlet 3 The unit appears to have cracks or is broken Do not use if the unit is damaged If you have concerns about using the unit discontinue use and contact the Remington Service Centre for further assistance 3 have switched the unit ON but cannot increase or decrease the energy level Try resetting the unit by turning it off and waiting several seconds before turning it back on 3 The Bulb Status Indicator Light turns green but the unit does not flash when the button is pressed Make sure the Skin Contact
11. it has fallen into water immediately unplug it from the electrical outlet 12 Do not plug or unplug the appliance with wet hands 13 This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been supervised instructed and understand the hazards involved Children shall not play with the appliance Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised 14 Keep the appliance and cable out of reach of children under 8 years 15 This appliance is not intended for commercial or salon use 16 This appliance should be supplied with approved safety isolating adaptors SW 120060EU for Europe and SW 120060BS for United Kingdom with the output capacity of 12 dc 600mA adaptor output OY Ul JS UY N w ON i LIGHT KEY FEATURES amp KEY FEATURES Power Switch Power Inlet Base Unit Hand Piece Flash Button Energy Level Selection Button Cool Down Mode Indicator CON AWM bh WN Bulb Status Indicator Display 9 Energy Level Indicator 10 Skin Tone Sensor 11 Hand Piece Cord 12 Flash Window 13 Skin Contact Sensors 14 Attachment Release Buttons 15 Bulb 16 Body Attachment 17 Power Cord 18 Lint Free Cloth GETTING STARTED Be patient when first using your i LIGHT as with any new product it may take a little while to familiarise yourse
12. lf with the product Take the time to acquaint yourself with your i LIGHT as we are confident you will receive years of enjoyable use and complete satisfaction GETTING ACQUAINTED WITH i LIGHT 3 What is i LIGHT The i LIGHT system is a revolutionary light based device designed for the removal of unwanted body hair at home i LIGHT utilises similar clinically proven technology that professional dermatologists and salons use optimised for personal treatment 3 What is Intense Pulse Light IPL and how does i LIGHT work IPL Intense Pulsed Light is a well established technology used worldwide for over 15 years i LIGHT uses this technology to flash your skin with an intense pulse of light The pulse works under the skin s surface to target hairs at the root helping to stop their growth Fig 1 The energy in the pulse of light targets dark colouring and best results are seen on darker hair To avoid targeting and possibly damaging dark skin you should only use i LIGHT on light to medium skin tones I IV 3 What to expect from i LIGHT Results aren t immediate and individual results vary Most users will begin to notice fewer hairs within 1 2 weeks after beginning treatment During this time it may look like the hair is still growing but it is actually being pushed out Fig 2 Fig 2 _ Hair grows in a cycle of 3 different phases which lasts 18 24 months Fig 3 Only hairs in the active growth phase
13. on naturally dark skin as it may result in burns blisters and changes in skin colour Do not use on tanned skin or after recent sun exposure as it may cause burns or skin injury e _i LIGHT is not effective on naturally white grey blonde or red body hair 3 Areas not to treat Do not use on the scalp or ears Do not use on the face or neck Do not use on nipples areola or genitals Do not use if you have tattoos or permanent makeup in the area to be treated Do not use on dark brown or black spots such as moles birth marks or freckles Do not use on an area of recent surgery deep peel laser resurfacing scars or skin that has been damaged with burns or scalds When not to use When to avoid using i LIGHT DO NOT use if you have tanned skin in the intended treatment area as your skin may be too dark and treatment in tanned areas could temporarily cause skin swelling blisters or could change the colour of your skin Wait until your tan has faded before treating e DO NOT use on skin with cosmetics applied as treating in those areas could temporarily cause skin swelling blisters or could change the colour of your skin Make sure to thoroughly clean the intended treatment area prior to use e DO NOT flash the same treatment spot multiple times during the same session as this could temporarily cause skin swelling blisters or could change the colour of your skin e DO NOT treat any area more than once per week as this
14. ou 3 NOTE You must test the device on each area of the body you wish to treat amp TREATMENT Multi Flash Mode The i LIGHT device will flash when the Flash Button is pressed and will continue to flash every 3 seconds when the skin contact sensors are fully engaged The Multi Flash mode allows you to quickly treat large areas by simply gliding the hand piece over the skin after each flash 3 How to treat Place the Flash Window firmly against the skin ensure the Skin Contact Sensors are fully engaged 3 NOTE When the Skin Contact Sensors are fully engaged you will hear a chirp and the Bulb Status Indicator Display will illuminate green 2 Press the flash button to deliver a flash You should expect to see a bright flash of light similar to a camera flash and you should feel a mild sensation of warmth 3 Move to the next area and treat in a grid like pattern to ensure full coverage of the treatment area For Single Flash Mode press the Flash Button each time you move to the next area For Multi Flash Mode keep your finger on the Flash Button to keep it depressed and glide to the next area being sure to keep the Skin Contact Sensors fully engaged The next flash will be delivered automatically after 3 seconds 3 NOTE During Multi Flash Mode if you let go of the Flash Button or lose skin contact simply resume treatment by repeating the above steps amp TREATMENT TIPS For best results avoid overlapping flashes
15. ped with 5 energy levels Level 1 is the lowest setting and level 5 is the highest setting 3 TIP For the most effective results always use the highest energy level that does not cause discomfort on the skin To determine the energy level being used observe the number of lights illuminated on the Energy Level Display fig 6 Fig 6 St A Ze qa e pa Your i LIGHT will automatically be set to Energy Level 1 each time the device is powered ON To change the level press the Energy Level Selection Button 3 TEST THE i LIGHT ON YOUR SKIN 3 Before your first full treatment test the i LIGHT on a small patch of skin and wait 24 hours to ensure there are no adverse reactions Start at energy level 1 Place the i LIGHT hand piece against your skin so the Flash Window is flush with the skin surface 2 Ensure the Skin Contact Sensors are fully engaged and the Bulb Status Indicator Display is illuminated green Fig 7 0 Fig 7 E J 3 Press the Flash Button to deliver a flash e Mild to moderate discomfort is normal If a flash delivered at Energy Level 1 feels tolerable increase to Energy Level 2 Move the device to a different spot and flash the i LIGHT one more time Repeat this process until you find the setting that feels right for you Wait 24 hours and then look at the test area If the skin appears normal proceed with your first full treatment at the energy level you determined is right for y
16. r under your skin to disable your hair at the root so it is not effective if the hair has been pulled out DO NOT use directly over or near Active Implantable Medical Devices such as implantable pacemaker internal defibrillator or insulin devices Although no problems associated with the use of this device have been reported during clinical studies it is recommended to observe all active implantable medical device warnings regarding the use of electronic devices to prevent any failure or interruption of an active implantable device Do not use over or near anything artificial such as silicon implants Implanon contraceptive implants pacemakers subcutaneous injection ports insulin dispenser or piercings Wireless communications equipment may affect the i LIGHT device and should be kept at least 3 3 m away amp PREPARING FOR USE 3 Familiarise yourself with the features of your new i LIGHT device 3 Flash Window with built in UV skin protection WARNING always inspect the Flash Window before use to ensure there is no damage to the lens WARNING always clean the Flash Window before use with the lint free cloth provided to ensure there is no oil or debris on the lens A 3 Skin Contact Sensors This safety mechanism prevents accidental flashing The device will not flash unless both Skin Contact Sensors are in full contact with the skin 3 Flash Button The Flash Button is located on the hand piece This is use
17. will not speed up results but could increase likelihood of skin swelling blistering or changing the colour of your skin DO NOT use on damaged skin including open wounds cold sores sunburns or areas where you have had a skin peel or other skin resurfacing procedure within the last 6 8 weeks DO NOT use on irritated skin including rashes or swollen skin These conditions can make the skin more sensitive Wait for the affected area to heal before use DO NOT use if your skin is sensitive to light In order to determine if you can use i LIGHT perform a test on a small patch of skin and wait 24 hours to determine if there are any adverse reactions before treating more broadly DO NOT use if you are or may be pregnant or are breast feeding i LIGHT has not been tested on pregnant women Hormonal changes are common during pregnancy or breast feeding and could increase skin sensitivity and the risk of skin injury e DO NOT flash against any material other than skin DO NOT use i LIGHT for any purpose other than hair removal e DO NOT treat any area where you may someday want your hair to grow back The results may be permanent and irreversible If you ve had professional or clinical or self administered laser or IPL or electrolysis hair removal treatments wait at least 6 months before using i LIGHT If you ve waxed plucked or epilated hair in the treatment area wait at least 6 weeks before using i LIGHT The device uses the hai
Download Pdf Manuals
Related Search
Related Contents
ATW-F808B 取扱説明書 Kensington K39565US Copyright © All rights reserved.
Failed to retrieve file