Cisco PWR-CORD-G2A-AP= power cable
Contents
1. Chapter 5 Field Replaceable Units and Region and Country Specific Power Cables Step 3 Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only W Remove the tie wraps from around the cables by pressing the latch on the tie wraps and removing them One of the tie wraps is shown with callout 1 in Figure 5 4 209094 Figure 5 4 Removing the Tie Wraps around the Cable Bundles Step4 Detach the cables from the codec Make a note of each cable connection You can use the tape flags on the cables for this purpose If your cables do not have tape flags you can make some with masking tape Step 5 Remove the two screws from each side of the codec one on each side These screws are at the top of the codec Save the screws Step6 Rotate the codec backward and remove it from the metal bracket Step7 Unpack the new codec Step8 Determine the placement of the diagram on the codec and make sure that it is oriented correctly and on the correct side of the codec and that it will not be upside down amp Note The new codec comes with a wiring diagram with a self adhesive backing Step9 Peel off the adhesive backing on the diagram and place it on the codec Step 10 Place the codec in the bracket in the display assembly and secure it with the screws you saved in Step 5 Step11 Reconnect the cables Use the tape flags or the wiring diagram on the codec as a guide Cisc2. Field Replaceable Units and Region and Country Specific Power Cables June 5 2013 OL 23420 01 This chapter describes the tasks you perform to replace the Field Replaceable Units FRUs for your Cisco TelePresence System 500 32 CTS 500 32 for first time use This chapter also includes a list of FRUs for the TelePresence system and region and country specific power cord information and includes the following sections amp List of Field Replaceable Units page 5 2 Finding the Serial Number Location page 5 3 Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only page 5 4 Replacing the Display Assembly Part Number CTS500 32 INTDISP page 5 9 Replacing the Rear Camera Cover Part Number CTS500 32 CAM CVRs page 5 12 Replacing the Camera Lens Cover Part Number CTS500 32 LENSCVR page 5 14 Replacing the Microphone Cover Part Number CTS500 32 MICCVRL Left or CTS500 32 MICCVRR Right page 5 17 Replacing the Power Supply Part Number CTS CODEC S PWRe page 5 18 Region and Country Specific Power Cables page 5 24 Note The display used in this product contains mercury Dispose of according to local state and federal laws I OL 23420 01 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide gy Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables W List of Field Replaceable Units List of Fie
3. 2 Phillips screwdriver Replacing the Codec Video For videos that show removal and replacement of the codec refer to the following URLs http www cisco com en US docs telepresence cts_500 cts_500_32 assembly guide video fru_videos removing_the_codec html http www cisco com en US docs telepresence cts_500 cts_500_32 assembly guide video fru_videos installing_the_codec html Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide a OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only Replacing the Codec Detailed Steps To replace the codec complete the following steps Step 1 Turn the On Off switch to the Off position Figure 5 2 On Off Switch Location 208933 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide oL 23420 01 g 5s Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only Step2 Remove the rear codec cover Figure 5 3 Removing the Codec Cover 209093 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01
4. MAC Address of the new Cisco Unified IP Phone Find the MAC address on a white sticker on the rear of the phone next to the Ethernet port Log in to the Unified CM Administrative GUI Enter the MAC address of the new Cisco Unified IP phone into the Administrative GUI The phone settings are stored in Unified CM and the MAC address is required for the phone to register with Unified CM I OL 23420 01 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables Hi Replacing the Cisco Unified IP Phone Part Number CP 7975G CTS Step 5 Step 6 Step7 amp Connect the new Cisco Unified IP Phone to the Ethernet cable to the 10 100 SW port the same port as was used on the existing phone The IP phone starts booting with the PoE provided by the TelePresence codec and attempts to register with Unified CM Wait for the phone to become active Press the Settings button on your Cisco Unified IP Phone Figure 5 13 Settings Button a Using the Up and Down arrows on the phone scroll down until you highlight the Network Configuration option Note Step 8 Step 9 Step 10 Step 11 Step 12 Step 13 Step 14 Step 15 Step 16 Step 17 Step 18 Step 19 Step 20 Step 21 Step 22 Step 23 Step 24 Step 25 Step 26 Step 27 Step 28 Step 29 Do not press the Select softkey yet Press St
5. country specific power cables Table 5 2 Region and Country Specific Power Cables Power Cord ID Description PWR CORD G2A AP TelePresence G2A Power Cords Asia Pacific PWR CORD G2A AR TelePresence G2A Power Cords Argentina PWR CORD G2A AU TelePresence G2A Power Cords Australia PWR CORD G2A CE TelePresence G2A Power Cords Central Europe PWR CORD G2A CN TelePresence G2A Power Cords China PWR CORD G2A ID TelePresence G2A Power Cords India PWR CORD G2A ISR TelePresence G2A Power Cords Israel PWR CORD G2A ITA TelePresence G2A Power Cords Italy PWR CORD G2A JP TelePresence G2A Power Cords Japan PWR CORD G2A NA TelePresence G2A Power Cords North America PWR CORD G2A SA TelePresence G2A Power Cords South Africa PWR CORD G2A SWI _ TelePresence G2A Power Cords Switzerland PWR CORD G2A UK TelePresence G2A Power Cords United Kingdom and United Arab Emirates Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01
6. Remove the camera lens cover Figure 5 8 Removing the Camera Lens Cover ate qili 209103 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide I OL 23420 01 SEN Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables WE Replacing the Camera Lens Cover Part Number CTS500 32 LENSCVR Step5 Attach the new camera lens cover to the system Figure 5 9 Attaching the Camera Lens Cover 209097 Step6 In the Cisco TelePresence Administrative GUI click Stop to retract the camera back into its enclosure Step7 Log out of the Cisco TelePresence Administrative GUI Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide Ea OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Replacing the Microphone Cover Part Number CTS500 32 MICCVRL Left or CTS500 32 MICCVRR Right Replacing the Microphone Cover Part Number CTS500 32 MICCVRL Left or CTS500 32 MICCVRR Right To remove the microphone cover grasp the microphone cover by its edges near the camera lens and pull outward Installation is the opposite of removal Figure 5 10 Removing the Speaker Cover ie Kins 209098 Cisco TelePresence System 500 32 Installat
7. ar Star Pound to unlock the network setting parameter The phone displays the following message on bottom of the screen Settings Unlocked In addition an unlocked icon appears on the top right of the screen Press the Select softkey Select IPv4 configuration and press the Select softkey Using the up and down arrows on the phone scroll to the DHCP selection Press the No softkey Press the Save softkey Scroll to the IP address selection and press the Edit softkey Enter the static IP address for the Cisco Unified IP phone Press the Validate softkey Scroll to the Subnet Mask selection and press the Edit softkey Enter the subnet mask for your static IP address Press the Validate softkey Scroll to the Default Router selection and press the Edit softkey Enter the IP address of the IP gateway default router Press the Validate softkey Scroll to the TFTP server 1 selection and press the Edit softkey Enter the IP address of the TFTP server Press the Validate softkey Optional scroll to the TFTP server 2 selection and press the Edit softkey Enter the IP address of the alternate TFTP server Press the Validate softkey m_ Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 Chapter 5 Field Replaceable Units and Region and Country Specific Power Cables Replacing the Cisco Unified IP Phone Part Number CP 7975G CTS W Step 30 Press th
8. bly Part Number CTS500 32 INTDISP W Replacing the Display Assembly Part Number CT 500 32 INTDISP The following section provides you with the procedure to replace the display and includes the following topics e Tools required page 5 9 e Replacing the Display Assembly Video page 5 9 e Replacing the Display Assembly Detailed Steps page 5 9 Tools required One 2 Phillips screwdriver amp Note Two people are required for installation to remove the display assembly from the column Replacing the Display Assembly Video For videos that show removal and replacement of the display complete the tasks as shown in the following URL Step 1 Remove the codec by completing the tasks in the following video http www cisco com en US docs telepresence cts_500 cts_500_32 assembly guide video fru_videos removing_the_codec html Step2 Remove the display by completing the tasks in the following video http www cisco com en US docs telepresence cts_500 cts_500_32 assembly guide video fru_videos removing_the_display html Step3 Install the new display by completing the tasks in the following video http www cisco com en US docs telepresence cts_500 cts_500_32 assembly guide video fru_videos installing_the_display html Step4 Replace the existing codec into the new display assembly by completing the tasks in the following video http www cisco com en US docs telepresence cts_500 cts_500_32 assembly guide vide
9. cation of this switch Open a browser on a computer connected to the network Type the IP address of the primary codec unit into the browser address bar Enter the required information at the login screen The Cisco TelePresence Administrator window appears Verify the status of the Cisco Unified Communications Manager seen in the lower left portion of the window is Enabled Up Select Hardware Setup to verify the cameras displays speakers and microphones are working properly See the Manual First Time Setup section on page 4 31 for more information Perform the Auto Adjust camera setup procedure This sets the white balance to the correct levels See the Manual First Time Setup section on page 4 31 for more information Configure the codec in CTS Manager by completing the following steps a Log in to CTS Manager as SysAdmin or Administrator b Go to Configure gt Application Settings c Disable the Meeting Notification Email by selecting No for Enable Feature and clicking Apply d Go to Configure gt Unified CM e Select the Unified CM that has the new codec f Click Discover Rooms The new codec with the existing room name is added and the previous codec is removed from CTS Manager w_ Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Replacing the Display Assem
10. e Save softkey to save your changes After the configuration is saved the IP phone will display the following text Updating CTL Step 31 Press Star Star Pound to lock your phone configuration The Cisco Unified IP Phone reloads and bring up the Cisco TelePresence screen Step 32 Wait for the phone to complete its bootup procedure After the IP phone has successfully booted up and registered with the Call Manager the IP phone ready screen will display See Figure 5 12 for an example of this screen Figure 5 14 IP Phone TelePresence Screen O TES ab Cisco TelePresence RR X New Call Directory Favorites Meetings Your current options Step 33 Check the status of the Cisco Unified IP Phone by completing the following steps a Log in to the Cisco Telepresence System Administration GUI to verify the IP Phone status Tip To find TelePresence system IP address press the More softkey then press the Info softkey on the Cisco Unified IP Phone b Look in the System Status area on the lower left of the window c Determine if there is a check mark next to Room Phone I OL 23420 01 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide gy Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables HZ Region and Country Specific Power Cables Region and Country Specific Power Cables Table 5 2 provides you with a list of the region and
11. ec cover Step15 Place the rear codec cover back on the display Step16 Follow these steps to configure the new codec in Cisco Unified Communications Manager a Open a browser on a computer connected to the network b Access the Cisco Unified Communications Manager interface c Add the Room Email ID of the previous codec to the new codec d Make sure the new codec s status is registered Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 m Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables WE Replacing the Rear Camera Cover Part Number CTS500 32 CAM CVR Step 17 Step 18 Step 19 Step 20 Step 21 Step 22 Step 23 Step 24 Step 25 Step 26 e Delete the MAC address of the previous codec from the Cisco Unified CM application user profile that is used in CTS Manager f Add the new codec to the application user profile and click Save Power on the system by turning the power switches to the On position on the two left PDUs single right PDU and if present auxiliary control unit or PDU on the rear center of the display assembly Open a browser on a computer connected to the network Type the IP address of the codec into the browser address bar Enter the required information at the login screen The Cisco TelePresence Administrator window appears Verify the status of the Cisco Unified Communications Manager see
12. era targets small and large Optional CTS CODEC SING1CH Codec China only Note To replace this part follow the procedure in the Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only section on page 5 4 CTS CODEC SING G1 Codec Note To replace this part follow the procedure in the Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only section on page 5 4 CTS CODEC S PWR Power supply Finding the Serial Number Location You might need the serial number of your CTS 500 32 to order FRUs The serial number is located on the rear of the display as shown in Figure 5 1 I OL 23420 01 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide gy Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables E Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only Figure 5 1 Serial Number Location SN XXXNNNNXXXX Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only This section provides you with the procedure to replace the codec for your system and includes the following topics e Tools required page 5 4 e Replacing the Codec Video page 5 4 e Replacing the Codec Detailed Steps page 5 5 Tools required One
13. he Cables Behind the Codec Bracket Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide u OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Replacing the Display Assembly Part Number CTS500 32 INTDISP W Step8 Loosen the screws that attach the display assembly to the column and pull the display off the column Figure 5 6 Removing the Display From the Column Unpack the new display assembly Step10 Put the new assembly back on the column and route the cable bundles upward behind the codec bracket Note Attachment of the display is the same procedure as removal with the steps performed in reverse Step11 Tighten the screws that attach the display to the column The screws are shown in Figure 5 6 Step12 Place the codec back in the bracket in the display assembly and secure it with the screws you saved in Step 5 Step13 Reconnect the cables Use the tape flags or the wiring diagram on the codec as a guide Step14 Use the tie wraps to route the cables Correct cable routing ensures that the codec cover can be placed on the rear of the display Therefore make sure that the cables do not cover the mounting holes for the codec cover and that they do not protrude so that you cannot attach the cod
14. ion First Time Setup and Field Replaceable Unit Guide I OL 23420 01 nE Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables W Replacing the Power Supply Part Number CTS CODEC S PWR Replacing the Power Supply Part Number CTS CODEC S PWR This section provides you with the procedure to replace the codec for your system and includes the following topics e Tools required page 5 18 e Replacing the Power Supply page 5 18 Tools required One 2 Phillips screwdriver Replacing the Power Supply To remove the power supply complete the following steps Step 1 Remove the codec by following the procedure in the Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only section on page 5 4 Step2 Disconnect the power cord from the power supply The cord is on the top of the supply Step3 Pull the power supply out from behind the codec cover Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide u OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Replacing the Cisco Unified IP Phone Part Number CP 7975G CTS W Figure 5 11 Removing the Power Supply n i Step4 Place the new power supply in the slot behind the codec cover Step5 Connect the power cord to the power supply to the power supply Step6 Replace the codec you remo
15. is screen w_ Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Step 7 Replacing the Cisco Unified IP Phone Part Number CP 7975G CTS W Figure 5 12 IP Phone TelePresence Screen O TESA va Cisco TelePresence New Call Your current options Check the status of the Cisco Unified IP Phone by completing the following steps a Log in to the Cisco Telepresence System Administration GUI to verify the IP Phone status Tip Step 8 DA To find TelePresence system IP address press the More softkey then press the Info softkey on the Cisco Unified IP Phone b Look in the System Status area on the lower left of the window c Determine if there is a check mark next to Room Phone Perform a test call to another Cisco TelePresence endpoint Note If the IP phone fails registering with Unified CM contact your Unified CM administrator or your authorized TelePresence representative Removing the Replacing the Cisco Unified IP Phone With Networks that Use a Static IP Address Step 1 Step 2 Step 3 Step 4 If your network uses a static IP address complete the following steps to replace your Cisco Unified IP Phone Unplug the Ethernet cable from the back of the existing Cisco Unified IP Phone The Ethernet port is marked as 10 100 SW Make a note of the
16. ld Replaceable Units Table 5 1 contains a list of the FRUs for the CTS 500 32 amp Note Most FRUs replace lost or broken items optional items are listed as Optional and do not come with the standard product configuration Table 5 1 FRUs for the CTS 500 32 FRU Description CP 7975G CTS Cisco IP Phone CP 7975G CTS500 32 ACC KIT Accessory kit The accessory kit includes the following parts e 37 0887 02 RJ45 to RJ45 cable 3 meters e 37 1025 01 RJ45 to RJ45 cable 8 meters e 37 1210 01 VGA to VGA cable with 3mm audio connection for external presentations 6 meters Note In addition to the VGA to VGA cable listed here you can order additional cables for video only external presentations CTS CABL VGA 2 VGA to VGA or CTS CAB HDMIDVID2 HDMI to DVI D CTS500 32 CABCVR Cable Sheath CTS500 32 CAM CVR Rear camera cover Note To replace this part follow the procedure in the Replacing the Rear Camera Cover Part Number CTS500 32 CAM CVR section on page 5 12 CTS500 32 COD CVR Codec cover CTS500 32 CVRDOOR Codec cover port access door CTS500 32 INTDISP Cisco TelePresence Integrated 32in Display without codec Note To replace this part follow the procedure in the Replacing the Display Assembly Part Number CTS500 32 INTDISP section on page 5 9 CTS500 32 LENSCVR Camera lens cover Note To replace this part follow the procedure in the Replacing the Came
17. n in the lower left portion of the window is Enabled Up Select Hardware Setup to verify the cameras displays speakers and microphones are working properly For more information see the Manual First Time Setup section on page 4 31 Perform the Auto Adjust camera setup procedure This sets the white balance to the correct levels See the Setting Up the Camera section on page 4 33 for detailed instructions Configure the codec in CTS Manager by completing the following steps a Log in to CTS Manager as SysAdmin or Administrator b Go to Configure gt Application Settings c Disable the Meeting Notification Email by selecting No for Enable Feature and clicking Apply d Go to Configure gt Unified CM Select the Unified CM that has the new codec Click Discover Rooms The new codec with the existing room name is added and the previous codec is removed from CTS Manager Replacing the Rear Camera Cover Part Number CT 500 32 CAM CVR Step 1 Step 2 To replace the rear camera cover complete the following steps Unscrew the two screws that secure the rear camera cover to the display assembly Unlatch the latch on the underside of the cover and lift it off the display assembly w_ Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Replacing the Rear Camera Cover Pa
18. o fru_videos installing_the_codec html Replacing the Display Assembly Detailed Steps To replace the display assembly complete the following steps Step 1 Turn off the system using the on off switch on the bottom of the column near the floor Step2 Remove the rear codec cover Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 oe Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables WE Replacing the Display Assembly Part Number CTS500 32 INTDISP Step3 Remove the tie wraps from around the cables by pressing the latch on the tie wraps One of the tie wraps is shown with callout 1 in Figure 5 4 Step4 Detach the cables from the codec Make a note of each cable position You can use the tape flags on the cables for this purpose If your cables do not have tape flags you can make some with masking tape Step5 Remove the two screws from each side of the codec one on each side These screws are at the top of the codec Save the screws Step6 Rotate the codec backward and remove it from the metal bracket Save the codec Note You do NOT have to remove the power supply behind the codec another one is supplied with the new display assembly Step7 Take the two cable bundles on each side of the display and route them downward behind the codec bracket until the two cable bundles hang on each side of the stand Figure 5 5 Routing t
19. o TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide I OL 23420 01 a 57 Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables E Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only Step 12 Step 13 Step 14 Step 15 Step 16 Step 17 Step 18 Step 19 Step 20 Step 21 Step 22 Use the tie wraps to route and rearrange the cables Callout 1 in Figure 5 4 shows the location of one of the two tie wrap Correct cable routing ensures that the codec cover can be placed on the rear of the display Therefore make sure that the cables do not cover the mounting holes for the codec cover and that they do not protrude so that you cannot attach the codec cover Place the rear codec cover back on the display Complete the following steps to configure the new codec in Cisco Unified Communications Manager a Open a browser on a computer connected to the network b Access the Cisco Unified Communications Manager interface c Add the Room Email ID of the previous codec to the new codec d Make sure the new codec s status is registered e Delete the MAC address of the previous codec from the Cisco Unified CM application user profile that is used in Cisco TelePresence Manager CTS Manager f Add the new codec to the application user profile and click Save Turn the codec power switch to the On position See Figure 5 2 for the lo
20. ra Lens Cover Part Number CTS500 32 LENSCVR section on page 5 14 CTS500 32 MICCVRL Microphone cover left Note To replace this part follow the procedure in the Replacing the Microphone Cover Part Number CTS500 32 MICCVRL Left or CTS500 32 MICCVRR Right section on page 5 17 CTS500 32 MICCVRR Microphone cover right Note To replace this part follow the procedure in the Replacing the Microphone Cover Part Number CTS500 32 MICCVRL Left or CTS500 32 MICCVRR Right section on page 5 17 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Finding the Serial Number Location W Table 5 1 FRUs for the CTS 500 32 continued FRU Description CTS500 32 PED Pedestal Stand Mount only CTS500 32 PEDCOL Column for table stand Table Mounted systems only CTS500 32 TABMT Table mount Note Order this FRU to convert your system from a pedestal mounted to a table mounted system CTS CABCVR FLR Cable cover floor mat Optional CTS CAB HDMIDVID2 HDMI to DVI D external presentation cable 2 meters Optional CTS CABL VGA 2 VGA to VGA external presentation cable 2 meters CTS CAB MGMTCUP External presentation cable holder table mounted cable cup Optional CTS CAM TOOL G2 Cam
21. rt Number CTS500 32 CAM CVR W Figure 5 7 Removing the Rear Camera Cover 209096 Step3 Attachment of the new rear camera cover is the opposite of removal Place the cover on the display assembly and secure it with the screws Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide oL 23420 01 SEE Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables WE Replacing the Camera Lens Cover Part Number CTS500 32 LENSCVR Replacing the Camera Lens Cover Part Number CT 500 32 LENSCVR To replace the camera lens cover complete the following steps Step 1 Log in to the Cisco TelePresence System CTS by completing the following steps Open a browser and type in the IP address of the system in the URL and press Enter a Inthe Admin field type admin b In the Password field type cisco c Click Login d Navigate to Troubleshooting gt Hardware Setup gt Cameras Step2 Click Start The camera drops from its enclosure Step3 Unscrew the screw that attaches the camera lens cover to the display assembly Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 Chapter5 Field Replaceable Units and Region and Country Specific Power Cables Replacing the Camera Lens Cover Part Number CTS500 32 LENSCVR W Step4
22. tape flags or another method for labeling the device and Ethernet cables Removing the Replacing the Cisco Unified IP Phone With Networks that Use a Dynamic IP Address Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 If your network uses the Dynamic Host Configuration Protocol DHCP to dynamically allocate an IP address for your Cisco TelePresence system complete the following steps to replace your Cisco Unified IP Phone Unplug the Ethernet cable from the back of the existing Cisco Unified IP Phone The Ethernet port is marked as 10 100 SW Make a note of the MAC Address of the new Cisco Unified IP Phone Find the MAC address on a white sticker on the rear of the phone next to the Ethernet port Log in to the Unified CM Administrative GUI Enter the MAC address of the new Cisco Unified IP phone into the Administrative GUI The phone settings are stored in Unified CM and the MAC address is required for the phone to register with Unified CM Connect the new Cisco Unified IP Phone to the Ethernet cable to the 10 100 SW port the same port as was used on the existing phone The IP phone starts booting with the Power over Ethernet PoE power provided by the TelePresence codec and attempts to register with Unified CM Wait for the phone to complete its bootup procedure After the IP phone has successfully booted up and registered with the Call Manager the IP phone ready screen will display See Figure 5 12 for an example of th
23. ved in Step 1 by following the procedure in the Replacing the Codec Part Number CTS CODEC SING G1 or CTS CODEC SING1CH China Only section on page 5 4 Replacing the Cisco Unified IP Phone Part Number CP 7975G CTS This section provides you with the steps you perform to replace the Cisco Unified IP Phone and includes the following topics e Required and Optional Tools page 5 20 e Removing the Replacing the Cisco Unified IP Phone With Networks that Use a Dynamic IP Address page 5 20 Cisco TelePresence System 500 32 Installation First Time Setup and Field Replaceable Unit Guide OL 23420 01 a 5 19 Chapter5 _Field Replaceable Units and Region and Country Specific Power Cables W Replacing the Cisco Unified IP Phone Part Number CP 7975G CTS Required and Optional Tools To replace the Cisco Unified IP Phone the following tools are required e Laptop computer for connecting to the Cisco TelePresence Administration Software and Cisco Unified Communications Manager Unified CM GUIs e RJ45 Ethernet straight through patch cable for the laptop to codec connection e Customer Unified CM administrator IP or DNS address ID and password to configure Unified CM e Customer Cisco TelePresence administrator IP or DNS address ID and password to configure the Cisco TelePresence Administration software The following items are optional but recommended e Phillips and flat head screwdrivers e Cable marker
Download Pdf Manuals
Related Search