Fibaro FGWPE-101 power plug adapter
Contents
1. Home Center 2 Measuring is carried out by an independent microprocessor dedicated exclusively for this purpose assuring maximum accuracy and precision Electric power power consumed by an electric device in an instant in Watts W Electric energy energy consumed by a device through a time period Most commonly measured in kilowatt hours kWh One kilowatt hour is equal to one kilowatt of power consumed over a period of one hour 1kWh 1000 Wh NOTE Please contact your local electricity supplier for the current rates NOTE Turning off the LED ring turns off alarm signaling as well 2 Fibaro Wall Plug stores consumed electricity data in its memory which means disconnecting the Plug from a socket does not erase the data To reset electricity consumption memory a Insert the Plug in a socket b Press and hold the B button for 5 10 seconds until LED ring glows green c Release the B button d Press the B button briefly Resetting electricity consumption memory will be signaled by double green LED ring blink Plug s relay won t change its status NOTE Some Z Wave network controllers allow for resetting electricity consumption from controllers menu 3 Frequently asked questions about power and energy consumption measuring Why doesn t a device consume precisely 100W when its data plate says this is the power exactly Power data specified by producers are often based on rough estimates or m2. Parameter 1 byte 63 LED ring illumination colour at the Z Wave network alarm detection Default setting 1 Available settings 0 No change in colour LED ring illumination colour determined by parameters 61 or 62 settings 1 LED ring flashes red blue white default 2 White illumination 3 Red illumination 4 Green illumination 5 Blue illumination 6 Yellow illumination 7 Cyan Greenish blue illumination 8 Magenta Purplish red illumination 9 illumination turned off completely Parameter 1 byte SAFETY 70 Oveload safety switch This function allows for turning off the controlled device in case of exceeding the defined power Controlled device will be turned off even if always on function is active parameter 1 Controlled device can be turned back on via B button or sending a control frame By default this function is inactive Default setting 65 535 6 553 5W Available settings 10 65 535 1W 6 553 5W Value higher than 32 000 3 200W turns the overload safety switch off ie this functionality is turned off by default Parameter 2 byte NOTE This functionality is not an overload safety protection nor a short circuit protection Circuit needs additional short circuit and overload protection XI Guarantee 1 The Guarantee is provided by FIBAR GROUP Sp z o o hereinafter Manufacturer based in Poznan ul Lotnicza 1 60 421 Poznan enter
3. associated devices on once the power rises above UP value parameter 51 Parameter 1 byte COLOUR SETTINGS 60 Power load which when exceeded makes the LED ring flash violet Function is active only when parameter 61 is set to 0 or 1 Default setting 25 000 2 500W Available settings 1 000 32 000 100W 3200W Parameter 2 byte 61 LED ring illumination colour when controlled device is on Default value 1 Available settings 0 LED ring illumination colour changes in predefined steps depending on power consumption changes 1 LED ring illumination colour changes continuously using full spectrum of available colorus depending on power consumption changes 2 White illumination 3 Red illumination 4 Green illumination 5 Blue illumination 6 Yellow illumination 7 Cyan Greenish blue illumination 8 Magenta Purplish red illumination 9 illumination turned off completely Parameter 1 byte 62 LED ring illumination color when controlled device is off Default setting 8 Available settings 0 LED ring is illuminated with a color corresponding to the last measured power before the controlled device was turned off 1 White illumination 2 Red illumination 3 Green illumination 4 Blue illumination 5 Yellow illumination 6 Cyan Greenish blue illumination 7 Magenta Purplish red illumination 8 illumination turned off completely
4. checks correction of errors or parameter programming and other activities that should be performed by the user Buyer The guarantee shall not cover natural wear and tear of the Device and its components listed in the operating manual and in technical documentation as such elements have a defined operational life 16 If a defect is not covered by the guarantee the Manufacturer reserves the right to remove such defect at its sole discretion repairing the damaged or destroyed parts or providing components necessary for repair or replacement 17 This guarantee shall not exclude limit or suspend the Customer rights when the provided product is inconsistent with the purchase agreement This Device may be used with all devices certified with Z Wave certificate and should be compatible with such devices produced by other manufacturers Any device compatible with Z Wave may be added to Fibaro system FIBARGROUP FIBARO In case of any technical questions contact customer service centre in your country www fibargroup com
5. in energy consumed by controlled devices New reported energy value is calculated based on last reported value Default setting 10 0 1 kWh Available settings 1 254 0 01kWh 2 54kWh Value of 255 changes in consumed energy will not be reported Reports will be sent only in case of polling Parameter 1 byte 47 Time period between reports on power load and energy consumption Parameter defines time period between reports sent when changes in power load have not been recorded By default if power load changes have not been recorded reports are sent every hour Default setting 3 600 s Available settings 1 65534 s Value of 65535 no periodic reports Reports will be sent only in case of power load energy consumption changes parameters 40 42 43 45 or in case of polling Parameter 2 byte 49 Metering energy consumed by the Wall Plug itself This parameter determines whether energy metering should include the amount of energy consumed by the Wall Plug itself Results are being added to energy consumed by controlled device Default setting 0 Available settings 0 function inactive 1 function activated Parameter 1 byte ASSOCIATION GROUP 2 Status of devices added to 2nd Association Group may depend on power consumed by the connected device For example turning on the TV controlled by the Plug will turn off the lights in the room User defines two thresholds UP and DOWN
6. operating status Colours shown are those of a RGB scheme In addition the LED ring signals Plugs range in relation to the Z Wave networks main controller and overheating protection activation parameter no 70 LED rings signaling modes 1 Wall Plugs On Off signaled with a color defined by relevant parameter settings see parameters no 60 61 62 2 Alarm status signaled according to parameters 63 settings 3 Energy meter reset signaled by double green blink 4 Once inserted to mains socket LED ring signals Z Wave network inclusion status Single green blink means it s included Single red blink means Plug has not been included in the Z Wave network 5 Blinking yellow means memory write during software update process 6 Alternating blinking yellow red signals overheating warning overload LED ring illumination may be turned off completely To do so 1 Insert the Plug in a socket 2 Press and hold the B button for 2 5 seconds till LED ring starts pulsing white 3 Release the B button 4 Press the B button briefly Plugs relay will not change its status After the LED ring has been turned off it can be turned on by completing again the above procedure The Fibaro Wall Plug features built in network range status in relation to the Z Wave network main controller To test the range 1 Insert Plug into a mains socket 2 Press and hold the B button for 10 15 seconds until the LED ring glows viol
7. unforeseen accidents theft water damage liquid leakage battery spill weather conditions sunlight sand moisture high or low temperature air pollution damages caused by malfunctioning software attack of a computer virus or by failure to update the software as recommended by the Manufacturer damages resulting from surges in the power and or telecommuni cation network improper connection to the grid in a manner inconsistent with the operating manual or from connecting other devices not recommended by the Manufacturer damages caused by operating or storing the device in extremely adverse conditions i e high humidity dust too low freezing or too high ambient temperature Detailed permissible conditions for operating the Device are defined in the operating manual damages caused by using accessories not recommended by the Manufacturer damages caused by faulty electrical installation of the Customer including the use of incorrect fuses damages caused by Customer s failure to provide maintenance and servicing activities defined in the operating manual damages resulting from the use of spurious spare parts or accessories improper for given model repairing and introducing alterations by unauthorized persons defects caused by operating faulty Device or accessories 15 The scope of the guarantee repairs shall not include periodic maintenance and inspections in particular cleaning adjustments operational
8. Operating Manual Fibaro Wall Plug FGWPE JF 101 v 2 1 v 2 3 Fibaro Wall Plug is a universal Z Wave compatible relay switch in the form of a socket adapter The Plug may be used to operate any device up to 2 500W power output The Plug features power consumption measuring and uses a crystal LED ring to visualize the current load by colour changing illumination Fibaro Wall Plug may be operated using the service button located on its casing or via any Z Wave compatible controller Specifications Power supply 110 230 V AC 10 50 60 Hz Rated load current 11A 110 230V 50 60 Hz continuous load 13A 110 230V 50 60 Hz momentary load Power consumption up to 0 8W Power output For resistive load 2 5kW at continuous load 3 0kW at momentary load In accordance with EU EN 55015 noise standards EN 60669 2 1 operational safety Circuit s temperature limit 105 C Operational temperature 0 40 C Circuit s thermal protection 115 C Ta Ta ambient temperature To be used with E or F type Schuko sockets CEE 7 16 max load 2 5 A CEE 7 17 max load 16A Dual type plugs E F Radio signal power 1mW Radio protocol Z Wave Radio frequency 868 4 MHz Range up to 50m outdoors up to 30m indoors depending on building materials Dimensions D x H 43 x 65mm NOTE In case of loads other than resistive please observe cos and use load lower than rated if necessary It s recommende
9. Wave network 1 Insert the Plug into a socket 2 Set the Z Wave network controller into the learn mode see Z Wave controller operating manual 3 Triple click the B button located on the Plug s casing V Resetting Fibaro Wall Plug Reset procedure clears the Plug s memory including Z Wave network controller information and energy consumption data To reset Fibaro Wall Plug 1 Insert the Plug into a socket 2 Press and hold the B button for 15 20 seconds until LED ring glows yellow 3 Release the B button 4 Press the B button briefly Once the reset procedure is completed LED ring will glow red and turn off Plug s relay will turn off as well NOTE Resetting the Plug does not mean is has been removed from Z Wave network controller s memory Remove the Plug from Z Wave network controller s memory before carrying out the resetting procedure VI Operating the Plug through Z Wave network After successful inclusion Plug will be represented in the Home Center 2 by the following single icon 9 xX Wall Plug Fig 1 Wall Plug icon in Home Center 2 interface Clicking ON OFF will turn a connected device On or Off VII Association Through an association Fibaro Wall Plug may control another Z Wave network device e g another Fibaro Wall Plug Dimmer Relay Switch or Roller Shutter NOTE Association allows for direct communication between Z Wave network devices Main controller does not tak
10. and then defines the reaction to them being exceeded parameter 52 50 DOWN value Lower power threshold used in parameter 52 Default setting 300 30 W Available settings 0 25 000 0 0W 2 500W DOWN value cannot be higher than a value specified in parameter 51 Parameter 2 byte 51 UP value Upper power threshold used in parameter 52 Default setting 500 50 W Available settings 1 25 000 0 1W 2 500W UP value cannot be lower than a value specified in parameter 50 Parameter 2 byte 52 Action in case of exceeding defined power values parameters 50 and 51 Parameter deifines the way 2nd association group devices are controlled depending on the current power load Default setting 6 Available settings 0 function inactive 1 turn the associated devices on once the power drops below DOWN value parameter 50 2 turn the associated devices off once the power drops below DOWN value parameter 50 3 turn the associated devices on once the power rises above UP value parameter 51 4 turn the associated devices off once the power rises above UP value parameter 51 5 1 and 4 combined Turn the associated devices on once the power drops below DOWN value parameter 50 Turn the associated devices off once the power rises above UP value parameter 51 6 2 and 3 combined Turn the associated devices off once the power drops below DOWN value parameter 50 Turn the
11. d In alarm mode Wall Plug does not report status change power changes ignores alarm frames After the defined time period has passed parameter 39 or after the alarm cancellation connected device is set to the previous state Parameter 1 byte NOTE If always on function is active parameter 1 this parameter s settings are ignored 39 Alarm duration Wall Plug s alarm mode duration If a device sending an alarm frame through the Z Wave network sets alarm duration as well this parameter s settings are ignored Default setting 600 seconds Available settings 1 65536 seconds Parameter 2 byte REPORTS Reports on power load sent to the main controller Default settings of below parameters are chosen in such a way that instantaneous power load is shown without blocking the Z Wave network in the process Default settings are good for most of the devices In specific cases it may be necessary to modify default settings in order to optimize Z Wave network s use In extreme cases it is recommen ded to turn off reporting completely and configure power polling or periodic reports in Home Center 2 Fibaro Wall Plug reports the power load with specified frequency Below configuration parameters allow to specify how and how frequently power load will be reported 40 Immediate power report Parameter defines by how much power load must change in percents to be reported to the main controller with the highe
12. d not to exceed 8A 1 5kW Technical Information Controlled by Fibaro devices or any other Z Wave controller Microprocessor control Executive element relay Active and historic average power consumption measuring I General information about Fibaro System Fibaro is a wireless system based on Z Wave technology Fibaro provides many advantages when compared to similar systems In general radio systems create a direct connection between the receiver and transmitter But the radio signal is weakened by various obstacles located on its path apartment walls furniture etc and in extreme cases it fails to transfer required data The advantage of Fibaro System is that its devices apart from being transmitters and receivers are also signal duplicators When a direct connection path between the transmitter and the receiver cannot be established the connection may be achieved through other intermediate devices Fibaro is a bi directional wireless system This means that the signal is not only sent to the receivers but also the receivers send the confirmation of its reception This operation confirms their status to check whether they are active Safety of the Fibaro System transmission is comparable to the safety of transmission in data bus wired systems Fibaro operates in the free band for data transmission The frequency depends on radio regulations in individual country Each Fibaro network has its own unique network id
13. e part in such communication The Fibaro Wall Plug provides three association groups I association group is assigned to Plugs status On Off Allows for sending control command to associated devices whenever the Plug is turned On or Off Il association group allows for sending control commands to associated devices depending on the current load This association group is configured through the advanced parameters no 50 51 and 52 Ill association group reports relay s status to just one device Z Wave network s main controller by default It s not recommended to modify settings of this association group The Fibaro Wall Plug allows for associating 5 normal devices per single association group out of which 1 field is always reserved for main controller NOTE Group association commands are sent only in case of manual operation through the B button Group Il association commands are sent automatically depending on parameters no 50 51 and 52 settings To add an association using Home Center 2 Interface go to device settings and click the following icon 9 Select the device options tab Then specify to which group and what devices are to be associated Sending relevant information to devices added to association groups may take even a few minutes VIII Current load and energy consumption 1 Fibaro Wall Plug allows for the current load and power consumption monitoring Data is sent to the main controller e g
14. e variety of advanced configuration settings Below parameters can be accessed from main controllers configuration interface To configure Wall Plug using Home Center 2 controller go to device options by clicking the following icon 9 Select the advanced settings tab GENERAL 1 Always on function Once activated Wall Plug will keep a connected device constantly ON will stop reacting to alarm frames and B button push Always on function turns the Plug into a power and energy meter Also connected device will not be turned off upon receiving an alarm frame from another Z Wave device parameter 35 will be ignored In Always on mode connected device may be turned off only after user defined power has been exceeded parameter 70 In such a case connected device can be turned on again by pushing the B button or sending a control frame By default overload protection is inactive Default setting 1 Available settings 0 function activated 1 function inactive Parameter 1 byte 16 Remember device status after power failure Define how will the Plug react after the power supply is back on Default setting 1 Available settings 0 Wall Plug does not memorize its state after a power failure Connected device will be off after the power supply is reconnected 1 Wall Plug memorizes its state after a power failure Parameter 1 byte ALARMS Z Wave network alarm will be signalled by LED ring acc
15. easured in perfect conditions Real world power depends on mains voltage device condition or ambient conditions the device is used in It may happen that two identical devices will consume different amounts of energy Why power of the same device differs depending on the socket it is connected to in the same house Such things happen because of mains voltage fluctuations Causes also include wire lengths and voltage drops between the sockets Why the power of the same device differs in times of day The reason is the mains voltage fluctuations Why do we measure power not any other parameter instead Power measuring is important because based on this parameter electricity suppliers charge households for energy use Why certain devices power fluctuates instead of being constant Some devices may have such a characteristic e g computers In case of devices frequently significantly changing power consumption e g plasma TVs it is recommended to modify configuration parameters to optimize the Z Wave network use Modify parameters no 40 42 and 43 settings in order to reduce the frequency of reporting the power use To reduce the number of power reports value of the parameters 42 and or 43 must be increased based on user s experience e g parameter 42 set to 30 and parameter 43 set to 60 IX Led rings settings and readings The Fibaro Wall Plug has built in colour changing LED ring signaling connected devices power and
16. ed in the register of the National Court Register kept by the District Court in Poznan VIII Economic Department of the National Court Register no 370151 NIP 7811858097 REGON 301595664 2 The Manufacturer is responsible for equipment malfunction resulting from physical defects manufacturing or material of the Device for 12 months from the date of its purchasing 3 During the Guarantee period the Manufacturer shall remove any defects free of charge by repairing or replacing at the sole discretion of the Manufacturer any defective components of the Device with new or regenerated components that are free of defects When the repair impossible the Manufacturer reserves the right to replace the device with a new or regenerated one which shall be free of any defects and its condition shall not be worse than the original device owned by the Customer 4 In special cases when the device cannot be replaced with the device of the same type e g the device is no longer available in the commercial offer the Manufacturer may replace it with a different device having technical parameters similar to the faulty one Such activity shall be considered as fulfilling the obligations of the Manufacturer The Manufacturer shall not refund money paid for the device 5 The holder of a valid guarantee shall submit a guarantee claim through the guarantee service Remember before you submit a guarantee claim contact our technical support using tel
17. entification number home ID which is why it is possible to co operate two or more independent systems in a single building without any interference Although Z Wave is quite new technology it has already become recognizable and officially binding standard similarly to Wi Fi Many manufacturers in various industries offer solutions based on Z Wave technology guaranteeing their compatibility This means that the system is open and it may be extended in the future Find more information at www fibaro com Fibaro generates a dynamic network structure After Fibaro System is switched on the location of its individual components is automatically updated in real time through status confirmation signals received from devices operating in a mesh network The Fibaro Wall Plug is hereinafter referred to as Plug It is designed to turn on off electrical devices see specifications using radio waves controllers and push button located in it s casing Plug automatically recognizes connected load and is protected from overcurrent or short circuit Features unique real time energy consumption measuring through color changing crystal LED ring Il Installation 1 Insert device into a socket 2 Add device into the Z Wave network if necessary 3 Connect load to the Plug making sure it does not exceed 2 500W 4 Set the connected device switch to ON 5 To turn on connected device manually turn on the Plug using B button Alternative to rem
18. ephone or e mail More than 50 of operational problems is resolved remotely saving time and money spent to initiating guarantee procedure If remote support is insufficient the Customer shall fill the guarantee claim form using our website www fibargroup com in order to obtain claim authorization When the guarantee claim form is submitted correctly the Customer shall receive the claim confirmation with an unique number Return Merchandise Authorization RMA 6 The claim may be also submitted by telephone In this case the call is recorded and the Customer shall be informed about it by a consultant before submitting the claim Immediately after submitting the claim the consultant shall provide the Customer with the claim number RMA number 7 When the guarantee claim form is submitted correctly a representative of the Authorised Guarantee Service hereinafter as AGS shall contact the Customer 8 Defects revealed within the guarantee period shall be removed not later than 30 days from the date of delivering the Device to AGS The guarantee period shall be extended by the time in which the Device was kept by AGS 9 The faulty device shall be provided by the Customer with complete standard equipment and documents proving its purchase 10 Parts replaced under the guarantee are the property of the Manufacturer The guarantee for all parts replaced in the guarantee process shall be equal to the guarantee period of the origina
19. et 3 Release the B button 4 Press the B button briefly 5 LED ring signals Z Wave network range see below for signaling modes description 6 To exit range testing mode press the B button briefly Plugs relay will not change its status Z Wave network range signaling modes LED ring pulsing green Wall Plug tries to establish direct connection with the main controller If direct connection cannot be established Plug will try routing connection with the main controller which will be signaled by LED ring pulsing yellow LED ring glowing green Wall Plug managed to establish a direct connection with the main controller LED ring pulsing yellow Wall Plug is trying to establish routed connection with the main cotroller via other Z Wave devices acting as signal repeaters LED ring glowing yellow Wall Plug managed to establish routed connection with the main controller After 2 seconds the Plug will try again to establish a direct connection with the main controller which will be signaled by LED ring pulsing green LED ring pulsing violet Wall Plug is located outside the Z Wave network s range or the network is busy Ultimately failure to connect with the main controller will be signalled by LED ring pulsing red After 2 seconds the Plug will again try to establish a direct connection with the main controller which will be signalled by LED ring blinking green X Advanced configuration Fibaro Wall Plug offers a wid
20. l device The guarantee period of the replaced part shall not be extended 11 Costs of delivering the faulty device shall be borne by the Customer For unjustified service calls the Service may charge the Customer with travel expenses and handling costs related to the case 12 AGS shall not accept a complaint claim only when the Device was misused or the manual was not observed the Device was provided by the Customer incomplete without accessories or nameplate it was determined that the fault was caused by other reasons than a material or manufacturing defect of the Device the guarantee document is not valid or there is no proof of purchase 13 The Manufacturer shall not be liable for damages to property caused by defective device The Manufacturer shall not be liable for indirect incidental special consequential or punitive damages or for any damages including inter alia loss of profits savings data loss of benefits claims by third parties and any property damage or personal injuries arising from or related to the use of the Device 14 The guarantee shall not cover mechanical damages cracks fractures cuts abrasions physical deformations caused by impact falling or dropping the device or other object improper use or not observing the operating manual damages resulting from external causes e g flood storm fire lightning natural disasters earthquakes war civil disturbance force majeure
21. ording to the parameter 63 settings Blinking in Red Blue White is a default setting Connected device state will be changed according to the parameter 35 settings By default connected device state will remain unchanged Wall Plug will be signaling an alarm through the time period specified in the parameter 39 10 minutes by default unless the alarm is cancelled earlier In addition Wall Plug may exit the alarm mode after the B button has been pressed and held for 2 5 seconds 34 Reaction to alarms Define Z Wave network alarms to which the Wall Plug will respond Default setting 63 Available settings 0 63 1 general alarm 2 smoke alarm 4 COalarm 8 CO2 alarm 16 high temperature alarm 32 flood alarm 63 device responds to all types of alarm frames Set value may be a sum of available values e g set value 5 means the Plug will respond to general alarm 1 and CO alarm 4 Parameter 1 byte 35 Wall Plug s response to alarm frames Parameter defines how the Wall Plug will respond to alarms device s status change Default setting 0 Available settings 0 no reaction 1 turn on connected device LED ring signals an alarm through defined time period parameter 39 or untill the alarm is cancelled 2 turn off connected device LED ring signals an alarm through defined time period parameter 39 or untill the alarm is cancelled 3 cyclically change device state each 1secon
22. ote control via Z Wave controller Once the Plug is turned on LED ring will glow 6 Current power load is visualized with LED ring color 7 Press B button to turn off the Plug manually 8 Once the Plug is turned off LED ring illumination is turned off as well Ill Z Wave network inclusion Fibaro Wall Plug may be controlled manually by the B button located on its casing or via any Z Wave controller To include the Plug into the Z Wave network please complete following tasks 1 Insert the Plug into a socket 2 Auto inclusion will be activated i e Plug automatically starts looking for Z Wave network controller Auto inclusion activation is signaled by a single red LED ring blink 3 Set the Z Wave network main controller into learning mode see Z Wave network controller operating manual 4 Fibaro Wall Plug should be recognized and automatically included into the Z Wave network After the inclusion process is completed Plug s auto inclusion function is deactivated i e Plug will not try to include itself into the Z Wave network NOTE To disable auto inclusion press the B button once after inserting the Plug into a socket To include the Plug manually without the use of auto inclusion 1 Set the Z Wave controller into the learn mode see Z Wave controller operating manual 2 Triple click the B button located on the Plug s casing IV Removing from Z Wave network To remove Fibaro Wall Plug from the Z
23. st priority in the Z Wave network By default Fibaro Wall Plug immediately sends power report if the power load changes by 80 Default setting 80 Available settings 1 100 Value of 100 means the reports are turned off Parameter 1 byte NOTE In extreme cases reports may be sent every second if rapid and significant power load changes occur Frequent reporting may overload the Z Wave network so these parameter s settings should reflect significant changes in power load only 42 Standard power load reporting Parameter defines by how much power load must change in percents to be reported to the main controller By default Fibaro Wall Plug sends power report if the power load changes by 15 By default such changes in power load may be reported up to 5 times per 30 seconds Wall Plug sends 5 reports during time period specified in paramater 43 Default setting 15 Available settings 1 100 Value of 100 means the reports are turned off Parameter 1 byte 43 Power reporting frequency This parameter defines how frequently standard power reports parameter 42 will be sent By default Wall Plug sends up to 5 reports each 30 seconds provided the power load changes by 15 Default seting 30 s Available settings 1 254 s Value of 255 Reports will be sent only as a result of parameter 47 settings or in case of polling Parameter 1 byte 45 Reporting changes
Download Pdf Manuals
Related Search