Da-Lite 37034L projection screen
Contents
1. INSTRUCTION BOOK FOR Tensioned Large Advantage Electrol DA LITE Important Safety Instructions Whe n using your video equipment basic safety precautions should always be followed including the following 1 2 or contact hot surfaces Read and understand all instructions before using Position the cord so that it will not be tripped over pulled f an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords rated for less amperage than the appliance may overheat 4 To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently 5 The use of an accessory attachment not recommended by the manufacturer may cause a ris of fire electric shock or injury to persons Tools Required for Installation 3 4 Open Wrench 1 8 Hex Key or Socket Driver included Pre Installation 1 2 Carefully unpack case from shipping crate Set aside the Installation Kit Items inside will be used during installation ake sure to recheck measurement of case for proper installation clearance Remove any protective foam from case f necessary adjust hanger brackets with a 3 4 open wrench or socket driver Case Installation2. Brown Down Tr Black Up Oo o Blue Common Green Yellow Ground Black Up Brown Down Green Yellow Ground Screen Motor Troubleshooting Visit www da lite com products tutorials php to find installation You can contact us by email at info da lite com or by phone and troubleshooting tutorials You will also find a link to Live at 800 622 3737 or 574 267 8101 with any additional Chat for interactive support troubleshooting questions Symptom Cause Solution Verify 115 125V or 220 240V If insufficient voltage rewire Incorrect line voltage Blown fuse Tripped circuit breaker Screen will not operate and motor does not hum No power to operating switch or junction incoming electric line Re Re ch place fuse set circuit breaker eck above Tighten all loose wire connections Correct any improper connections Down Position ch eck for power across black and white leads Up Position ch eck for power across red and white leads Thermal overload tripped Screen will not operate Broken wire in the down or up position and motor does not hum Power at junction box Defective motor limit switch or capacitor Capacitor burned out Le ch Re Re motor cool down for 15 minutes Try again eck for continuity Cut off old splice and
3. Re install the access door Procedure is the reverse of step 1 listed above Bolts Screen Motor Limit Switches Bolts Figure 2 Figure 3 Tensioned Large Advantage Electrol Installation Suggested 1 2 Threaded Rod Not Included Attached to Mounting Bracket A Electrical Junction Box 2 e O O e 123 Screen Roller 11 gt o a 1 Audience 9 Side Self Trimming y Y Flange en e N i i Self Trimming Access Door 1 Finished eh In BY 2 10 746 gt Variable Position Mounting Brackets Electrical Junction Box Screen Adjustment Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da Lite Should it be necessary to adjust for more or less drop of picture proceed in the following manner NOTE Use a screw driver or 5 32 Allen wrench to make adjustments More Screen Drop LVC Control Box 1 Place operating switch in down position 2 When the screen stops turn the white down limit knob Figure 4 one quarter turn counterclockwise Test by raising picture surface approximately two feet then lower again Repeat until desired picture surface position is attained CAUTION Do not adjust for more drop than what
4. n wrench or socket driver to loosen th re pin end mo er into position ten all four bol left side The li head of the m Figure 1 roller assembly from shipping board using a 1 2 Leave packing paper on roller he square peg bracket from the motor end of the assembly Figu bracket he screen housing e four unting bracket into housing Lift and slide the bracket into the s Slide the pin end bracket d of the case Figure 3 assembly into the case with the motor on the mit switches should be facing down Line up the otor with the motor attachment bracket Door Support Access Door 7 Complete electrical hook up by snapping motor 1 3 wire connectors into case connectors Figure 2 Return to motor end and insert safety clip over casting bracket to secure motor end Carefully remove tape strips securing picture surface around roller Slat should move freely Only if the roller assembly is pre installed A CAUTION Do not cut tape on fabric with a knife or any sharp tool Remove by hand A ATTENTION Ne coupez pas le ruban adh sif sur la toile 10 LVC Control Box Screen Motor avec un couteau ou un outil tranchant Retirez a la main Test installation by running screen up and down a few times Be prepared to stop screen should any objects obstruct the movement of the screen To prevent damage to the motor the standard duty cycle is 1 minute on and 3 minutes off
5. gt gt gl The case provides multiple attachment points for bolts cables or threaded rod Page 4 shows threaded rod installed The variable position mounting bracket may be located anywhere along the length of the case It is recommended to keep the brackets spaced evenly enough to distribute the weight of the screen One mounting bracket is required for every 4 of case lenath Tighten bolts until trim flange is flush with ceiling NOTE For proper operation screen assembly must be level after installation Remove 2 screws to open junction box Install electrical connections that apply to your unit Make sure to review the wiring diagram for proper hook up Replace junction box cover and secure with 2 screws NOTE Please Note Motor Operator Projection Screen Models LADT LADDT LAD and LADD must be installed in accordance with the requirements of the Local Building Codes the Canadian Electrical Code CEC CAN CSA C221 and the National Electric Code NEC NFPA 70 An appropriate disconnect device shall be provided as part of the building installation If your case was ordered in advance of the screen and roller assembly your installation is now complete Continue to step 4 if your Tensioned Large Advantage Electrol was ordered as a complete unit Carefully remove paper and tape from roller assembly CAUTION Do not use a knife or sharp object to cut tape you will damage the screen Pull orange s
6. may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 800 622 3737 F 574 267 7804 or 877 325 4832 E info da lite com www da lite com DL 0123 Rev 2 04 14 O 2014 Milestone AV Technologies LLC Printed in U S A 35890
7. was ordered At least 1 1 2 wraps of fabric must remain on the roller This screen comes standard with 12 black at the top A ATTENTION N effectuez pas de r glage pour obtenir un d roulement sup rieur celui command Au moins 1 a 1 2 tour de toile doit tre maintenu sur le cylindre Ce cran est dot de s rie d une bande noire sup rieure de 30 5 cm 12 po Less Screen Drop 1 Raise picture surface approximately two feet above Screen Motor Screen Motor desired level Limit Switches 2 Place operating switch in off position Figure 4 3 Turn the white down limit switch Figure 4 one quarter turn clockwise Test by raising picture surface approximately two feet then lower again Repeat until desired picture surface position is attained A Caution Adjusting the down limit switch for less drop by more than 6 can cause the screen surface to lose proper tensioning A ATTENTION Le fait d ajouter ne d roulez pas trop l cran plus de 15 cm 6po aux interrupteurs de fin de course peut faire perdre la bonne tension la surface de l cran 120V Wiring Diagram With Optional Built In Low Voltage Control NOTE 20 24 AWG wire recommended for connecting wall switch to low voltage controller A CAUTION Do not use 3 position high voltage rocker switch with this unit This will damage the low voltage control
8. board A ATTENTION NE UTILISEZ PAS l interrupteur bascule fourni avec l cran Le tableau de contr le basse tension sera endommag Front of Wall Back of Switch Wall Switch O NV White Common Red Up Black Hot White Common Green Ground 4 Black Down Eye Port OT Power Input Plug IR or RF 120VAC 60Hz Remote Here D i White Common T Black Down i T Red Up White Common 0 m Black Down r Red Up O MN o T Green Ground SS y y O Green Ground Screen Motor 240V Wiring Diagram With Optional Built In Low Voltage Control NOTE 20 24 AWG wire recommended for connecting wall switch to low voltage controller A CAUTION Do not use 3 position high voltage rocker switch with this unit This will damage the low voltage control board A ATTENTION NE UTILISEZ PAS l interrupteur bascule fourni avec l cran Le tableau de contr le basse tension sera endommag Front of Back of Wall Switch Wall Switch 0 Blue Common Y E Brown Hot Green Yellow Ground 4 Red Up Power Input White Common 120VAC 60Hz Black Down Wire Nut Eye Port Plug IR or RF Black Remote Here of O Wire Nut Blue Common MN
9. ply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the five 6 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you
10. reconnect place motor assembly NOTE Motor is a sealed assembly place motor assembly Screen does not stop ae Limit switch out of adjustment at correct position See Screen Adjustment section Squeaking rubber end plug rubbing on motor Noise Grinding Foreign object in screen Cel nter roller in case NOTE Screen will operate bbi i adn Remove with a low pitched hum AS Gear noise Replace motor assembly Coasting Defective brake Replace motor assembly Screen not installed properly Fabric hangs crooked Fabric has backed up inside case Fabric is damaged Ch Ad wr Re eck for level and plumb just down limit switch slowly until roller is exposed and inkle comes out then readjust for proper drop place fabric LIMITED FIVE YEAR WARRANTY ON DA LITE TENSIONED ADVANTAGE ELECTROL ADVANTAGE ELECTROL TENSIONED LARGE ADVANTAGE ELECTROL LARGE ADVANTAGE ELECTROL TENSIONED CONTOUR ELECTROL AND CONTOUR ELECTROL PRODUCTS ONLY Milestone AV Technologies LLC warrants these Da Lite branded products to the original purchaser only to be free from defects in materials and workmanship for a period of five 5 years from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not ap
11. tring ATTENTION Ne coupez pas le ruban adh sif sur la toile avec un couteau ou un outil tranchant Retirez la main Use supplied 1 8 hex key to remove silver shipping brackets attached to slat and screen case Test installation by running screen up and down a few times Be prepared to stop screen should any objects obstruct the movement of the screen To prevent damage to the motor the standard duty cycle is 1 minute on and 3 minutes off Screen And Roller Assembly Installation Tools required for screen and roller assembly NANA 9 16 Open Wrench or Socket Driver 5 32 Hex Key 1 8 Hex Key included 1 2 Open Wrench or Socket Driver If your screen was shipped with the motor and roller already installed proceed to step 7 1 Remove the access door Firs end with a 9 16 open wrench hex key to remove the two screws in the his will allow the door door T Figure 1 Careful y unpa ck screen and e2 rive cen non bolts from each Next use a 5 32 er of the access the hinges remove th or socket d o drop ope b oller assembly Use supplied 1 8 hex key to remove shipping brackets attached to slat Remove fabric and wrench Remove t rolle Remove t located in the Use a 1 2 ope bolts that secu pin end of roll roller pin Tigh towards the e Place the rolle e 2 he safety clip from the motor attachemen motor end of t
Download Pdf Manuals
Related Search