Home

Da-Lite 35263 projection screen

image

Contents

1. INSTRUCTION BOOK FOR Tensioned Professional Electrol DA LITE Important Safety Instructions Whe n using your video equipment basic safety precautions should always be followed including the following 1 2 Read and understand all instructions before using contact hot surfaces rated for less amperage than the appliance may overheat To reduce the risk of electric shock do not disassemble this appliance Contact an authorized service dealer when repair work is required Incorrect reassembly can cause electric shock when the appliance is used subsequently The use of an accessory attachment not recommended by the manufacturer may cause a risk of fire electric shock or injury to persons Save These Instructions Pre Installation Position the cord so that it will not be tripped over pulled or f an extension cord is necessary a cord with a current rating at least equal to that of the appliance should be used Cords Carefully unpack screen Make sure to recheck measurements of screen location before installation Remove instruction cover plate Fig 1 Do not remove wrapping paper until screen is installed Remove the retainer screws from the slat bar before the case has been installed Fig 2 Instruction Cover Case Figure1 3 Screws 1 On Bottom of Slat 2 On Inside of Case Slat Retainer Bracket Figure 2 Installa
2. In multiple control To junction box mounted in screen Black Down installations the switch is case in which interal wiring terminates White Common replaced by the low in white black and red leads Green Ground voltage control operated E from push A A A button be stations 5 Green Ground a EL l a g Black x 2 g Down a g Operating switch p 6 AC Common switch box and Opas AC Hot plate furnished with off a screen SPDT with 115V AC 6OHZ center off 5 LAMP MAX Green Down x Ground Side View Of Red Black With Switch amp Box ia Up Yellow Green Ground This switch cannot be used with LV C NOTE A single switch cannot be used to operate more than one screen Contract the factory for further information 240 VOLT WIRING DIAGRAM FOR STANDARD WALL SWITCH Da Lite offers two styles of 240 volt wall switches for standard operation Please see wiring diagram in wall switch box included with screen Screen Adjustment Surface travel is stopped automatically in the fully opened and closed positions by limit switches that are properly adjusted at Da Lite A CAUTION Contact Da Lite at 800 622 3737 or 574 267 8101 if screen motor needs adjustment A ATTENTION Contactez Da Lite au 800 622 3737 ou au 574 267 8101 au cas le moteur de l cran a besoin d tre ajust Troubleshooting Visit www da lite com to find installation and troubleshooting tutorials You will
3. AS TO FITNESS FOR USE AND MERCHANTABILITY Any implied warranties of fitness for use or merchantability that may be mandated by statute or rule of law are limited to the one 1 year warranty period This warranty gives you specific legal rights and you may also have other rights which vary from state to state TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW NO LIABILITY IS ASSUMED FOR EXPENSES OR DAMAGES RESULTING FROM INTERRUPTION IN OPERATION OF EQUIPMENT OR FOR INCIDENTAL DIRECT OR CONSEQUENTIAL DAMAGES OF ANY NATURE In the event that there is a defect in materials or workmanship of a Da Lite product you may contact our Sales Partners at PO Box 137 Warsaw IN 46581 0137 574 267 8101 800 622 3737 IMPORTANT THIS WARRANTY SHALL NOT BE VALID AND DA LITE BRANDED PRODUCTS SHALL NOT BE BOUND BY THIS WARRANTY IF THE PRODUCT IS NOT OPERATED IN ACCORDANCE WITH THE DA LITE WRITTEN INSTRUCTIONS Keep your sales receipt to prove the date of purchase and your original ownership A Milestone AV Technologies Brand 3100 North Detroit Street Warsaw Indiana 46582 P 574 267 8101 or 800 622 3737 F 574 267 7804 or 877 325 4832 E info da lite com www da lite com DL 0170 Rev 2 10 14 2014 Milestone AV Technologies LLC Printed in U S A 33871
4. also find a link to Live Chat for interactive support and you can contact us by email at info da lite com or by phone at 800 622 3737 or 674 267 8101 with any troubleshooting questions Symptom Cause Solution Screen will not operate and motor does not hum Blown fuse Tripped circuit breaker No power to operating switch or junction Power at junction box Thermal overload tripped Broken wire in the down or up position Defective motor limit switch or capacitor Capacitor burned out Replace fuse Reset circuit breaker Check abov Correct any e Tighten all loose wire connections improper connections Down Position Check for power across black and white leads Up Position Check for power across red and white leads Let motor cool down for 15 minutes Try again Check for continuity Cut off old splice and reconnect Replace mo Replace mo or assembly NOTE Motor is a sealed assembly or assembly Incorrect stopping position in downward direction Lost roller wrap Down limit switch out of adjustment See instruct Contact Da ons below te at 800 622 3737 or 574 267 8101 Incorrect stopping position in upward direction Lost roller wrap Up limit switch out of adjustment See instruct Contact Da ons below e at 800 622 3737 or 574 267 8101 Noise NOTE Screen will operate wit
5. down should have at least a full wrap and a half around the roller Do not allow any part of the roller to become exposed Not on 4 Roller Figure 4 Slat i Tensioned Professional Electrol Installation Reinforced Top Motor End Electrical Outlet Box Ceiling Type Hanger 2 Moulding Picture Surface 1 x 3 Cleat Picture Surface o Ceiling Mount Without Hangers Screen case is placed flush with the wall and ceiling and held in position by moulding securely attached to the wall Picture Surface Wall or Ceiling Mount With Hangers Wall type hangers and ceiling type hangers are standard equipment One set is supplied with each screen Useful for recessed installations Rafters Picture Surface Recessed Above Ceiling Other methods of installation will suggest themselves in new buildings where it would be an easy matter to provide a recess for the screen to conceal it when not in use Do not seal in allow access For Exposed Installation If the screen is to be mounted in an exposed position it may be covered with finisned plywood veneer paneling plastic wall covering or a valance Tensioned Professional Electrol Installation 120V Wiring Diagram re Red Up
6. h a low pitched hum Coasting Gear Noise Defective brake Replace mo Replace mo or assembly or assembly LIMITED ONE YEAR WARRANTY ON DA LITE PRESENTATION PRODUCTS Milestone AV Technologies LLC warrants certain Da Lite branded products to the original purchaser only to be free from defects in materials and workmanship for a period of one 1 year from the date of purchase by the original purchaser provided they are properly operated according to Da Lite s instructions and are not damaged due to improper handling or treatment after shipment from the factory This warranty does not apply to equipment showing evidence of misuse abuse or accidental damage or which has been tampered with or repaired by a person other than authorized Da Lite personnel Da Lite s sole obligation under this warranty shall be to repair or to replace at Da Lite s option the defective part of the merchandise Returns for service should be made to your Da Lite dealer If it is necessary for the dealer to return the screen or part to Da Lite transportation expenses to and from Da Lite are payable by the purchaser and Da Lite is not responsible for damage in shipment To protect yourself against damage or loss in transit insure the product and prepay all transportation expenses TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING WARRANTIES
7. tion Hangers If required 1 See Figure 3 for hanger placement 2 Make sure hangers are placed to fit into notches of ironing board Screens 22 Wide And Under ue ae A Kc f P 5 lt AA Case Length 2 12 Case Length 23 3 12 Screens Over 22 Wide Figure 3 Installation Level unit lengthwise with a carpenter s plum level CAUTION Do Not completely seal in unit Access room must be allowed for motor repair or fabric replacement ATTENTION Ne fixez pas compl tement l unit Un espace doit tre laiss pour pouvoir r parer le moteur ou remplacer la toile Remove shipping brace by removing 2 hex head screws Figure 4 Use supplied 1 8 nex key and a 5 16 wrench to remove silver shipping brackets attached to slat and screen case Remove wrapping paper CAUTION Do not cut wrapping paper with knive or any sharp tool Remove by hand A ATTENTION Ne coupez pas le papier d emballage ou le ruban adh sif avec un couteau ou un outil tranchant Retirez a la main Shipping Brace Install electrical hook up that applies to your unit Make sure to review your Electrical Installation Checklists and wiring diagrams included for either 110 volt switch 220 240 volt switch or DRC low voltage control Test installation by carefully running surface up and down several times Be prepared to stop screen NOTE The picture surface when rolled

Download Pdf Manuals

image

Related Search

Related Contents

"user manual"  Manual Alpha 1200    Owners manual animeo® Solo  Activision Skylanders Spyro's Adventure Starter Kit 47875841543 User's Manual  Lennox International Inc. G43UF User's Manual    ダウンロード    Numark Industries RM6 Musical Instrument User Manual  

Copyright © All rights reserved.
Failed to retrieve file