Havis DS-DA-602
Contents
1. 4 Hardware Kit J Bracket a Machine Screw Pan Head 6 32 x 1 4 Long 2 Phillips Drive with Adhesive Patch 2 2 Cables b Thread Forming Screw Pan Head a USB Cable b Power Cable 6 32 x 1 4 Long 2 Phillips Drive 3 c Zip Ties 2 Q e THE POWER CABLE INCLUDED WITH THE DS DA 602 IS UNIQUE TO THIS PRODUCT DO NOT USE THE DS DA 602 POWER CABLE WITH ANY OTHER HAVIS DEVICE DO NOT USE ANY OTHER HAVIS DEVICE S POWER CABLE WITH THE DS DA 602 Port Replication and Fuse ri a a lt a ue Ethernet RJ45 USB 2 0 out USB 2 0 in Power Input 10 100 Type A Type B 9 24V DC LED Diagnostics 2 0 Amp Fuse Top of Rugged Hub USB Indicators 4 Power Indicator Status USB Indicators 4 Port has an over current ower indicator FSS Input Power is between 9V 24V Power Indicator Voltage less than 9 or more than 24 Installation amp Cable Management e THE DOCKING STATION AND OR UNIVERSAL TRAY DEPICTED IN THESE INSTRUCTIONS MAY NOT PRECISELY MATCH YOUR PRODUCT HOWEVER THE INSTRUCTION STEPS REMAIN APPLICABLE e IF MOUNTING RUGGED HUB TO ANY SURFACE OTHER THAN A HAVIS DOCKING STATION OR UNIVERSAL TRAY USE THE APPROPRIATE FASTENER AND TORQUES FOR YOUR INSTALLATION 1 Remove Strain Relief Bracket from Rugged Hub Be sure to retain fastener for reassembly in Step 4 2 Identify your required mounting configuration and select the appropriate2. fasteners from the Hardware Kit OPTION A If the back side of the panel to which the Rugged Hub is intended to be mounted is accessible use Hardware Kit Item 4a This is typically a Docking Station mounting configuration OPTION B If the back side of the panel to which the Rugged Hub is intended to be mounted is not accessible use Hardware Kit Item 4b This is typically a Universal Tray mounting configuration G OPTION A OPTION B Bottom view of Rugged Hub www havis com 1 800 524 9900
3. 4 Fto 149 F Storage Environment 30 C to 70 C 22 F to 158 F FCC Statement This device complies with the requirements of the Code of Federal Regulations listed below FCC Title 47 CFR Part 15 Class A for a digital device Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class A digital device 5 As needed use Zip Ties supplied in Hardware Kit to further strain relieve excess pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against cable lengths Be certain to allow for a service loop to accomodate the full range harmful interference when the equipment is operated in a commercial environment This equipment of intended motion generates uses and can radiate radio frequency energy and if not installed and used in accordance with instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense E www havis com ee en HAVIS watson Qmd DS DA 602 OMN 5 14 Parts Included 3 CD with Driver Software 2 _ oe pe Strain Relief
4. Owner s Manual Havis Rugged Hub DS DA 602 Installation amp Cable Management continued 3 Secure Rugged Hub to mounting surface OPTION A Typical Docking Station OPTION B Typical Universal Tray Align holes on bottom of Rugged Hub Align holes on top of Rugged Hub with with two 2 holes in panel and secure three 3 holes in panel and secure from from back side using Hardware Kit Item 4a front side using Hardware Kit Item 4b Torque screws to 14 in lbs 10 Torque screws to 14 in Ibs 10 i Before Beginning F Havis is pleased to provide this Owner s Manual to aid in the proper installation and use of the DS DA 602 Rugged Hub For questions regarding the set up of your DS DA 602 Rugged Hub please contact Havis at 1 800 524 9900 or visit www havis com for additional product support and information e THE POWER CABLE INCLUDED WITH THE DS DA 602 IS UNIQUE TO THIS PRODUCT DO NOT USE THE DS DA 602 POWER CABLE WITH ANY OTHER HAVIS DEVICE DO NOT USE ANY OTHER HAVIS DEVICE S POWER CABLE WITH THE DS DA 602 e READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION 4 Connect all required cables between peripheral devices and Rugged Hub Specifications then reinstall the Strain Relief Bracket as shown with fastener retained Power Supply Input from Step 1 Dimensions 5 1 12 9 cm W x 3 3 8 4 cm D x 1 0 2 5 cm H Weight 0 6 Ibs 0 3 kg Operating Environment 20 C to 65 C
Download Pdf Manuals
Related Search