Plantronics Voyager Edge
Contents
1. If necessary enter four zeros 0000 for the passcode or accept the connection Once successfully paired you hear pairing successful and the headset indicator lights stop flashing Select language Once your headset is paired and connected to your phone you can change the headset language Wearing your headset power it on Press and hold the Volume up and down buttons together until you hear welcome The language selection directions repeat in every supported language Follow the voice guided prompts to select the headset language Charge Check headset battery status It takes 90 minutes to fully charge the headset The indicator light turns off once charging is complete TIP To reset the accuracy of the talk time prompt deplete the headset battery then charge fully Headset LED behavior while charging with micro USB cable Off Charging complete eee Battery high Battery medium Battery low Battery critical There are three ways to check your headset battery status Wearing the headset tap the Voice button say Check battery and listen to the voice alert Wearing the headset tap the Call control button and listen to the voice alert When not wearing the headset tap the Call control button and observe the headset LEDs Headset LED behavior for battery status Off Charging complete e Battery high e Battery low less than 30 minutes rema2. Select a new headset language using your headset see Select language Download and install the HUB app on your phone visit plantronics com apps Download and install the MyHeadset Updater tool visit plantronics com myheadset To use voice commands tap the Voice button G gt wait for command request then say a command For example What can say tells you the full list of available commands Voice commands list Am connected Answer 14 Use two phones Change headset settings Update headset firmware Call back Cancel Check battery Ignore Pair mode What can I say NOTE The voice dial feature on your phone is initiated by pressing the Call button for 2 seconds The voice dial feature is not a headset voice command Disable the answer ignore voice commands Power on the headset Press and hold the Voice button G gt until you hear voice answer off Repeat to reactivate the voice answer commands Multipoint technology lets you pair a second phone and answer calls from either phone Once you have paired your two phones it s easy to answer calls from either phone When on a call you will hear a ringtone notification of the incoming call from the second paired phone To answer a second call from the other phone you must end the current call tap Call button so the new call automatically answers If you choose to not answer the second call it will go to voicemail You can
3. change the headset settings two different ways Download and install the HUB app on your phone visit plantronics com apps Download and install the MyHeadset Updater tool visit plantronics com myheadset The following headset settings can be changed Turn voice commands on off Turn high quality audio A2DP streaming on off Turn Wideband Audio for HD Voice on off Customize smart sensors Customize mute You can update your headset firmware using a USB cable and computer with the MyHeadset Updater tool installed Connect your headset and USB cable to your computer Download the MyHeadset Updater tool by visiting plantronics com myheadset Besides receiving firmware updates you can also change language and regional settings and configure other features 15 Specifications Talk time Up to 16 hours talk time using fully charged case and headset Up to 6 hours talk time without using case Standby time Up to 7 days Weight 9 grams Smart sensor technology Noise cancelling Dual capacitive sensors wearing status Triple mic active Digital Signal Processing DSP Acoustic echo cancellation Sidetone detection Automatic volume adjustment Water resistance P2i nano coating on headset and case to repel moisture NFC pairing Touch headset to NFC enabled phones to complete pairing process Bluetooth profiles Advanced Audio Distribution Profile A2DP Wideband Hands Free HFP Profi
4. Voyager Edge Series User Guide Contents What s inthe box 3 Headset overview 4 Charge case overview 5 Pair 6 Bluetooth pairing 6 NFC pairing 6 Pair Another Phone 6 Select language 7 Charge 8 Check headset battery status 8 Use the charge case 9 Fit 10 Adjust the fit 10 The Basics 11 Make Take End Calls 1 Mute 12 Adjust the volume 12 Use Smart Sensors 12 Play or pause streaming audio 13 More Features 14 Voice alerts 14 Voice commands 14 Use two phones 15 Change headset settings 15 Update headset firmware 15 Specifications 16 What s in the box Headset with medium eartip Car charger Micro USB cable Earloop Small and large eartip NOTE Charger style may vary by product Headset overview Call button Volume button Micro USB charge port Mute button Voice button Play Pause button Power button Headset LED indicator light Charge case overview IMPORTANT The charge case is placed in deep sleep mode after manufacturing to save power and protect the battery To wake up the charge case plug it into a power source for a minimum of 1 minute The LED s flash when charging so Charge case LEDs indicates case headset battery status Headset Touch the icon to display the headset battery status QW Charge case Touch the icon to display the charge case battery status Micro USB charge port When fully charged the charg
5. e case provides an extra 10 hours of battery life for the headset Pair Bluetooth pairing NFC pairing Pair Another Phone NOTE f your phone supports Near Field Communication NFC go to NFC pairing Wearing your headset power it on You hear welcome in all the supported languages and then pairing in the default language The headset LED flashes red and blue Activate Bluetooth on your phone and set it to search for new devices e iPhone Settings gt Bluetooth gt On Android Settings gt Bluetooth On gt Scan for devices NOTE Menus may vary by device Select PLT Edge If necessary enter four zeros 0000 for the passcode or accept the connection Once successfully paired you hear pairing successful Ensure NFC is on and your phone s display is unlocked Tap and hold the headset to the phone s NFC tag location until NFC pairing completes If necessary accept the connection TIP Keep an eye on your Smartphone s screen for prompts to start and accept the pairing process NOTE The headset s NFC tag is located on the top of the headset Phone NFC tag locations vary After pairing your headset to your phone you may want to pair another phone Power on your headset Choose Tap the Voice button G gt and say Pair mode e Press and hold the Call button until you hear pairing Activate Bluetooth on your phone and set it to search for new devices Select PLT Edge
6. ining eee Battery critical under 10 minutes remaining Use the charge case A fully charged case can supply an additional 10 hours of headset talk time IMPORTANT The charge case is placed in deep sleep mode after manufacturing to save power and protect the battery To wake up the charge case plug it into a power source for a minimum of 1 minute The LED s flash when charging Check the charge case or headset battery status by touching swiping either the case or headset icons The LEDs indicate the battery status Battery status LEDs for charge case and headset e Battery high Battery medium e Battery low De Battery critical Recharge case headset oN Fit Adjust the fit The loop of the gel eartip tucks into the back curve of your ear for a stable fit With the headset powered off replace the eartip with one of the two alternate sizes if it feels loose or tight in you ear To adjust the fit rotate the eartip on the headset or add the optional clip on earloop NOTE If the eartip feels loose after use remove the eartip wash it in warm water let it dry and reattach The Basics Make Take End Calls Answer a call Choose Put on the headset to answer call or Say answer after call is announced or Tap the Call button Answer a second call First tap the Call button to end current call then tap the Call button again to answer ne
7. le 1 6 Headset HSP Profile 1 2 and Enhanced Date Rate EDR Mulltipoint technology Connect two phones and answer calls from either phone Battery type Rechargeable non replaceable lithium ion polymer Charge connector Headset battery meter Micro USB charging on headset and charging case Automatically shows on screen for iPhone and iPad For Android devices use the free Plantronics app Charge time maximum Operating and storage temperature 90 minutes for full charge 32 F 104 F 0 40 C NOTE Performance is dependent upon battery and may vary by device 16 NEED MORE HELP plantronics com support plantronics Simply Smarter Communications Plantronics Inc Plantronics BV 345 Encinal Street South Point Building C Santa Cruz CA 95060 Scorpius 140 United States 2132 LR Hoofddorp Netherlands 2014 Plantronics Inc All Rights Reserved Bluetooth is a registered trademark of Bluetooth SIG Inc and any use by Plantronics is under license iPhone is a trademark of Apple Inc All other trademarks are the property of their respective owners Patents U S 5 712 453 7 039 179 Patents pending 202056 06 06 14 MODEL ID PITE14 plantronics
8. r pause or resume playback of streaming audio NOTE You must pause your streaming audio before you use your headset s voice commands initiate an outbound call with your headset call back or voice dial NOTE f you power off the headset or go out of phone range while streaming audio your headset will not play pause the stream upon reconnecting until you manually resume streaming with your phone More Features Voice alerts Voice commands You can change the language of voice alerts three different ways Select a new headset language using your headset see Select language Download and install the HUB app on your phone visit plantronics com apps Download and install the MyHeadset Updater tool visit plantronics com myheadset Voice alerts list Following is a list of the most frequent voice alerts Answering call Battery low Calling back last number Incoming call Lost connection Mute on off No phone is connected Pairing Pairing incomplete restart headset Pairing successful Power on off Phone X connected disconnected Recharge headset Say a command Smart sensors on off Talk time remaining X hours Volume maximum minimum Adjust voice alert volume Toggle the volume button when the headset is powered on and idle not on a call or streaming music to adjust the volume of the headset s voice alerts You can change the language of voice commands three different ways
9. ute on or mute off An alert repeats every 15 minutes when mute is on NOTE If the headset smart sensors are enabled default mute is deactivated when the headset is taken off and everyone can hear each other Toggle the Volume button up or down during a call or while streaming audio While not on a call or streaming audio you can toggle the Volume button to adjust the volume level for Caller Announce and other voice prompts Smart sensors in this headset recognize if the headset is being worn and can automatically perform time saving functions Putting on your headset will Answer an incoming call Transfer an active call from your phone Resume streaming audio Taking off your headset will Transfer an active call to your phone Pause streaming audio Lock the Call button to avoid accidental calls Reset sensors You may need to reset the sensors if they are not working as expected To reset your sensors connect the headset directly to your computer s USB port and place it with the eartip up on a flat non metallic surface for more than 10 seconds 12 Play or pause streaming audio Disable sensors To disable the sensors hold both the Voice S and Call buttons for more than 6 seconds until the LED flashes purple then red Repeat to reactivate the LED flashes purple then blue NOTE Sensors cannot be disabled while streaming audio A 2 second press of the Play Pause button II will eithe
10. w call End a call Tap the Call button to end current call Reject a call Choose Say ignore after call is announced or Press Call button for 2 seconds Call back last call Double tap the Call button to call back the last active call regardless of whether it was an inbound or an outbound call NOTE If no calls have been made or received in the current connected session this feature will not function Double tapping the Call button will result in a single low tone for each button press however will not connect you to the last active call from the previous session Voice dial phone feature If your smartphone has a voice enabled assistant press the call button for 2 seconds and wait for phone prompt 11 Mute Adjust the volume Use Smart Sensors Caller Announcement mobile phone only When wearing your headset you will hear the name of a contact calling you so you can decide whether to answer or ignore the call without having to check the phone screen An incoming caller name is announced if your phone supports Phone Book Access Profile PBAP if you granted access to your contacts during pairing process for many mobile phones this is preset out of the box and may not be necessary if the caller is stored in the phone s contacts list An incoming caller name is not announced if the caller is unknown unlisted or blocked During a conversation press the Mute button amp You hear m
Download Pdf Manuals
Related Search