Ematic EMW222 flat panel ceiling mount
Contents
1. Install the screws to fix the ceiling mount and VESA plate together tightly 944 6 Adjustment Remove the decorative covers for adjusting tension Itis necessary that slightly loosen or tighten adjustment screws to adjust tension using a proper Allen key Loosen screws but not remove and adjust the display to desired height as needed then tighten screws 102. INSTALLATION MANUAL 7 Adjustment Folding LCD Ceiling Mount Adjust to the desired position CAUTION DO NOT EXCEED RATED LISTED WEIGHT SERIOUS INJURY OR PROPERTY DAMAGE MAY OCCUR ISSUED MAY 2013 For saving the space you can fold the display by pushing the display back until it fits in place WUT g Maintenance e Check that the bracket is secure and safe to use at regular intervals at least every three months e Please contact your distributor if you have any questions 11444 1 NOTE Read the entire instruction manual before you start installation and assembly WARNING e Do not begin the installation until you have read and understood all the instructions and warnings contained in this installation sheet If you have any questions regarding any of the instructions or warnings please contact your local distributor e This mounting bracket was designed to be installed and utilised ONLY as specified in this manual Improper installation of this product may cause damage or serious injury e This product should only be installed by someone with good mechanical ability who has basic building experience and fully understands this manual e Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components e Always use an assistant or mechanical lifting equipment to safely lift and position the equipment e
3. Tighten screws firmly but do not over tighten Over tightening can cause damage to the items This greatly reduces their holding power e This product is intended for indoor use only Using this product outdoors could lead to product failure and personal injury Component Checklist IMPORTANT Ensure that you have received all parts according to the component checklist prior to installation If any parts are missing or faulty telephone your local distributor for a replacement ceiling mount x1 __J __ 4mm Allen key x1 6mm Allen key x1 B C Package M M4x14 x4 M5x14 x4 M6x14 x4 M A M B M C D5 washer x4 D8 washer x4 M F Package W ST6 3x55 x4 concrete anchor x4 W A W B M8x20 x4 M D l small spacer x8 M G D6 washer x2 W C b 2 1 Separating the VESA Plate 3a For Wooden Ceiling Mounting _oomm M22 ye 4 5MM gi 3 16 mark the exact location of mounting holes Use a proper Allen key to loosen the screws in order to separate the VESA plate from the ceiling mount 2 Opening the Mount Drill pilot holes a Screw the screws into the ceiling Tighten the screw leaving a 4mm space to ceiling Open the mount for installing Press the ceiling plate down then lift it up till fully open 3b For Solid Brick and Concrete Mounting Align the both holes of ceiling plate to the screws in ceiling and move the ce
4. iling plate until the both screws are seated in upper area of tear drop mounting holes Mark the exact location of mounting holes Drill pilot holes Fix the ceiling plate using the two other screws and then tighten all screws Screw the screws into the ceiling N WARNING e Installers are responsible to provide hardware for other types of mounting situations Tighten the screw leaving a 4mm space to ceiling e Installers must verify that the supporting surface will safely support the combined weight of the W A equipment and all attached hardware and components 54 b 6 4 Installing the VESA Plate Align the both holes of ceiling plate to the screws in ceiling and move the ceiling plate until the both screws are seated in upper area of tear drop mounting holes Fix the ceiling plate using the two other screws and then tighten all screws N WARNING Installers must verify that the supporting surface will safely support the combined weight of Note Choose the appropriate screws washers and spacers if necessary according to the type of screen the equipment and all attached hardware and components e Screw the VESA plate onto the display ZX Tionten all screws but do not over tighten T44 8 5 Hooking the Display onto the Ceiling Mount Hang the display with the VESA plate onto the ceiling mount SS Xa D B
Download Pdf Manuals
Related Search