Home

Provision-ISR PZ-22IR surveillance camera

image

Contents

1. Input AC100 240V 50 60Hz Output DC12V 5 5A Max Power IR off 15W Consumption IRon 31W Sync system Internal Sync Language English Pan Speed 0 08 2407S Tilt Speed 0 08 240 S Pan Range 0 360 Continuous Tilt Range 0 90 180 auto flip Preset 128 Preset Accuracy lt 0 1 Tour 4 27 presets tour Pattern 4 Zone 1 Protocol RS485 Communication PELCO D P auto detected Baud Rate 2400bps 4800bps 9600bps 19200bps Address 1 255 By DIP Switch or Software sjh RTC Set any functions at any time Superpower LED Default Zoom x1 5 open the near distance IR lights Zoom 6 9 open the near distance and middle distance IR lights IR Light switch Zoom x10 turn off the near distance IR lights open the middle distance and far distance IR lights Work Indoor O C 50 C Temperature Outdoor 20 C 50 C with heater Work Humidity 9096 3 Installation Site Preparations 3 1 Tool List 1 Screws 2 Monkey wrench 3 Philips screwdriver 4 Straight Screwdriver 5 Wire stripper 6 Socket head wrench 7 Electric drill 8 Hammer 9 BNC connector 10 BNC Clamp Included in the kit 3 2 Installation Preparation 1 Check the space and toughness of the site and make sure that the environmental conditions meet the installation requirements for this product 2 The installation surface should be ab
2. f 3 PA password If the old Password input is not correct you will not be able to change the password e lt CONFIRM gt Re input the new password and confirm If the input is not the same as the first time input the system will remain the old password e PSWD PROTECTION Switch on off the password protection When it is On user need to enter password in order to access OSD menu or save preset through keyboard e BACK return to upper menu e EXIT exit the menu 4 3 5 SET DEFAULT Main Menu SYSTEM SET DEFAULT Select SET DEFAULT to restore factory default setting Please note there is no confirmation prompt Once entering the camera will immediately restore itself 4 3 6 SYSTEM REBOOT Main Menu SYSTEM SYSTEM REBOOT gt Select SYSTEM REBOOT to reboot the dome 4 3 7 RTC TIME SET Main Menu SYSTEM RTC TIME SET DATE Y M D 000000 TIME H M S 000000 BACK EXIT Use left and right keys to move the cursor to desired item use up and down keys to change the current cursor value 4 3 8 RTC RIME RUNNING Main Menu SYSTEM RTC TIMER RUNNING DATE Y M D 00 TIME H M S 00 00 00 ACTION PRESET 001 BACK EXIT DATE and TIME Setup time running time 24 hour ACTION Choose one function from lt PRESET gt ZONE TOUR PATTERN to run BACK Back to the upper menu EXIT Exit the current menu 4
3. avoid facing the camera directly into strong light To prevent damage do not drop the unit or allow to strong shocks or vibrations Make sure no object is blocking the unit s full range of motion 2 Features 2 1 Product Picture dei 2 2 Product Features 3 0 Adaptive PELCO P D protocol Adjustable IR illumination 4 Memoryrecall Real Time Control call any functions at any time Upto8 privacy masks Support 128 preset positions English OSD menu user friendly for smooth operation Proportional zoom Auto flip function Builtin lightning proof and surge proof Advanced step motor Less heat Smooth movement No shaking Efficient heating device ensure to work in 20 low temperature Support 4 groups cruise scan 27 presets group 4 group patterns one scan and 360 continuous scan and 360 intermittent scan IR lights automatically adjust the light intensity according to the zoom f 1 PR speed to reduce the dark angle and flashlight effect The upper dome adopts 7 aluminum alloy structure for better magnetic shield and heat radiation Theunderpart dome adopts full metal class points bin type design for fast heat dissipation and anti mist non interference light source images and long life span IR light 2 3 Specifications
4. 4 LENS Main Menu LENS ZOOM SPEED HIGH DIGITAL ZOOM OFF JOYSTICK AF AI BOTH AF RESUME TIME 005 AI RESUME TIME 005 DAY NIGHT IR CTR CAMERA P N AUTO BACK EXIT 9 ZOOM SPEED Set the zoom speed level to HIGH or LOW e DIGITAL ZOOM Turn On Off the Digital Zoom JOYSTICK AF AI gt Set up Auto Focus AF Auto Iris Al or Both BOTH Joystick movement triggers both auto focus and auto iris FOCUS Joystick movement triggers auto focus only IRIS Joystick movement triggers auto iris only NONE Joystick movement triggers none of the functions lt AF RESUME This item sets the time to restore auto focus after focus is manually changed The default setting is 005 options are OFF Never restore auto focus after switch to manual 001 255 The dome will start auto focus that number of seconds after user manually adjusts focus AI RESUME This item sets the time to restore auto iris after iris is manually changed The default setting is 005 seconds options are OFF Never restore auto iris after switch to manual 001 255 The dome will start auto iris that number of seconds after user manually adjust iris DAY NIGHT Set the dome color black white mode Color mode is suitable to work in daytime because it needs higher illumination Light sensitivity of black amp white mode is much higher It is suitable to work at night without
5. illumination but the video is black and white There are 4 options AUTO The dome will automatically change modes according to the environment illumination COLOR The dome is always in color mode NIGHT The dome is always in Black and White mode IR CTL The dome is controlled by the IR lights sensor when the IR lights opened the mode auto change to Black and White L E CAMERA P N Show the current camera P N PAL NTSC The PTZ can automatically detected some of the camera Signal mode If not please set manually 4 5 CAMERA Important Note Camera setting will vary between Z 22lR and Z 27IR For the Simple camera menu access Main Menu CAMERA Simple Camera Menu WHITE BALANCE AUTO BLC MODE BACK EXIT e WHITE BALANCE gt White Balance is normally compensated for by the automatic white balance gain control In some lighting conditions user may want to manually adjust the red and blue settings for optimal viewing There are 6 options AUTO Auto White Balance default setting MANUAL Manually set the red and blue values setup from 000 to 255 ATW Auto track White Balance OPW Once touch White Balance OUTDOOR Suitable for outdoor use INDOOR Suitable for indoor use e BLC MODE If the backlight is bright the objects in the center of the picture may appear f PA dark The dome can auto adjust the brightness of the who
6. 11 1 0 128 129 10000001 130 131 11000001 132 133 10100001 134 135 11100001 136 137 10010001 138 139 11010001 140 141 1 0 t tT 0 9 0 1 142 35 143 11110001 144 145 10001001 146 147 11001001 148 149 10101001 150 151 11101001 152 153 10011001 154 155 11011001 156 157 10111001 158 159 41 T 1 0 160 161 10000101 162 163 11000101 164 165 10100101 166 167 11100101 168 169 1 0 0 1 0 1 170 171 11010101 172 173 1 0 11 0 1 0 41 174 175 41 LI 1 t0 1 01 176 177 10001101 178 179 4 1 0 0 1 1 0 14 180 181 4 0 1 0 1 1 0 1 182 183 4 1 0 1 1 0 14 184 185 4 0 0 1 1 1 0 1 186 187 1 1 0 3 Y 1 188 189 10 1 1 1 1 0 1 190 191 T T 1 544 0 1 192 193 10000011 194 195 11000011 196 36 197 10100011 198 199 4 1 1 0 0 0 1 1 200 201 202 203 1i 10 1 0 0 141 204 205 1 50 1 1 0 0 T 1 206 207 1 11 10 0 25 208 209 10001011 210 211 1 1 0 1 41 212 213 10101011 214 215 1 41 41 0 4 0 1 216 217 1 0 01 T 0 t1 218 219 41 0 4 220 221 4 1 0 1 1 222 223 1 11 1 0 1 1 224 225 10000111 226 227 1 10 0 0 1 1 1 228 229 10100111 230 231 11100111 232 233 1 00 T 0 1 1 1 234 235 4 10 L0 11 1 236 237 1 0 t0 1 141 238 239 240 37 APPENDI
7. IND User Manual Z 221R Z 27IR Package Contents 2 22 27 IR PTZ Wall Bracket Hinge Pin Rubber Seal DC12V 5A power supply Wall Screws PM8 25 socket head screws e RP Allan Key User Manual Table of Contents T General Instructioris n n ttti e P HE 3 1A Safety Instructions iion e e His 3 1 2 WARNINGS ie ERO Or RERO E EORNM 3 pA cp cc ee 4 2 2 PO UCEF a UCS ad vas nee 4 2 3 Specificatiotis 5n eise nim eni 5 3 Installation Site Preparations n nite tee emitte e 6 SA Toolibist iue p UR 6 3 2 Installation Preparation 6 3 3 DIP Switch Set p 2 ioi e RR 7 4 Setup of the OSD MenUu i RO 8 4 1 Display Boot UP Info i itte a ec exe 8 4 2 Enter the OSD Menu tede ERR ER 9 4 3 SYSTEM iiie ER UE EAE 10 GA LENS aeree x pss e eteteetade ng 15 V CAMERA iiit RH E MR E n EE 17 4 6 PAN TILT ee ER 211 4 7 AUTO RUNNING ordsssocs otdiotesgisbacb sgssanse sucks boddssisbarsosb dersanistbsb dsspsnren 22 4 8 PRIVACY MASK iis ios iE Rea ERE ee DER Ee ade ates 29 49 ALARM 300 410 Er REPE snaran 311 AsV
8. IR START SET 006 IR CLOSE SET 012 BACK EXIT e IR MODE gt AUTO OPEN CLOSE AUTO Default When the detected signal value from the IR sensitive below the value of IR Start the IR dome automatically open the IR lights OPEN Open the IR lights forcibly No influence from the detected signal value CLOSE Close the IR lights forcibly No influence from the detected signal value Notice The function only effective in LENS gt lt DAY NIGHT gt IR CHANGE mode 9 IRZOOM SET 1 006 The second section IR Zoom value 9 IRZOOM SET 2 010 The third section IR Zoom value 9 PRESENT LUX gt Display the current illumination value Unit Lux cannot be edited IRSTART SET 006 Default Open IR light illumination value Range 0 8 Unit Lux IR CLOSE SET 012 Close IR light illumination value Range 12 20 Unit Lux PA APPENDIX I DIP SWITCH SETTING DIP Switch consists of 8 numbers from 1 8 use 8421 binary cod max 255 address When the switch is in the ON position the number from 1 8 corresponding to 1 2 4 8 32 64 128 For example if you set 1 3 5 7 switch to the ON position the corresponding address will be 1 4 16 64 85 please refer to the blow details Sheet 1 1 ON O OFF DIP switch K1 ID Switch number 1 DIP switch K1 ID Switch number 1 number 8 number 8 Address 14 2 3 4 5 6 7 8 Ad
9. VIR SET 2 nni ERO 322 APPENDIX I DIP Switch Setting 33 APPENDIX II Shortcuts Key 8 3838 APPENDIX III Trouble Shooting sess 400 jh 1 General Instructions 1 1 Safety Instructions Make sure to read the user manual before using the product Always follow national and local safety codes during the installation Only qualified and experienced person can carry this installation and maintenance Usereliable tools not complying can result in serious injury Make sure that the environmental conditions meet the installation requirements for this product Please check the space and toughness of the site before installing It should be able to bear 4 times the weight of the dome and its accessories 1 2 Warnings not install this speed dome in hazardous places where combustible or explosive materials are stored or used not install on platform that suffers from constant vibrations Make sure no object or fluid substances get inside the unit This speed dome runs on DC 12V do not connect it to higher or lower voltage Do not turn power on before installation is complete Do not disassemble any part of the items Use soft towel to clean the down cover when necessary do not use caustic detergent To protect CCD
10. X II Shortcuts Key Chart Shortcut Key Function Set Preset Set 71 preset Set H73 preset Proportional P T OFF OS Park time ON Set H74 preset 60S Park time ON Set H75 preset 1205 Park time ON Set H76 preset Dome restart Set H77 preset Restore Factory Setting Set H78 preset 360 scan and tour scan speed is automatic Set H79 preset 360 scan and tour scan speed is high 207 sec Set 80 preset 360 scan and tour scan speed is middle 157 sec Set 81 preset 360 scan and tour scan speed is low 67 sec Set H82 preset Delete left right limit Set 84 preset Record Pattern scan 1 Set 85 preset Record Pattern scan 2 Set 86 preset Record Pattern scan 3 Set 87 preset Record Pattern scan 4 Set H88 preset Set cruise 1 Set 89 preset Set cruise 2 Set H90 preset Set cruise 3 Set H91 preset Set cruise 4 Set H94 preset Set color to black function Set H95 preset Open main menu Set 97 preset Set 360 scan the preset dwell OS Set 98 preset Set 360 scan the preset dwell 5S Set H99 preset Set 360 scan the preset dwell 10S Shortcut Key Function Call Preset Call 471 preset Proportional P T ON Call 82 preset Call 83 preset Start Cruise scan and switch the cruise scan direction Delete all Preset
11. ce default setting MANUAL Manually set the red and blue values setup from 000 to 255 ATW Auto track White Balance OPW Once touch White Balance OUTDOOR Suitable for outdoor use INDOOR Suitable for indoor use lt AGC gt changing the value of AGC lt DNR gt Turning digital noise reduction on off lt BACKLIGHT gt switching between OFF BLC HLC lt HLC LEVEL gt after choosing HLC in the backlight menu you can change level of HLC effect lt MIRROR gt Turning Mirror effect ON OFF lt BRIGHTNESS gt Changing the brightness value lt SHARPNESS gt Changing the sharpness value lt MASK SETTINGS gt This mask setting it referring to the zoom module only and will not be effective in a PTZ lt COLOR gt Adjusting color levels 6 L 060 4 6 PAN TILT Main Menu PAN TILT AUTO STOP TIME OFF SPEED AMPLIFY OFF PROPORTIONAL P T ON SET NORTH BACK EXIT e AUTO STOP TIME For some particular protocols the dome will not stop moving even there is no operation on CCTV Tester This menu sets the time after which the dome receives last control command Off Disable this function 001 255 The time second that dome will stop moving without receiving any commands e SPEED AMPLIFY gt Some protocols controlling speed is much lower set SPEED AMPLIFY gt to accelerate domes movement Options are as below Off Disable this function 01x 32x Speed amp
12. dress 12 3 4 5 6 7 8 1 10000000 2 01000000 3 11000000 4 00100000 5 10100000 6 01100000 7 11100000 8 00010000 9 10010000 10 01010000 11 11010000 12 00110000 13 1 0 1 14 01110000 15 1 2 1 1 0 0 0 16 00001000 17 10001000 18 01001000 19 11001000 20 00101000 21 10101000 22 0 r 10 00 23 11101000 24 00011000 25 10011000 26 01011000 27 110110 70 0 28 00111000 29 10111000 30 01111000 31 1 1 1 1 1 050 32 00000100 33 10000100 34 01000100 35 36 37 38 39 41 40 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 95 81 82 83 84 85 86 87 88 34 89 1 0 1 1 0 10 90 91 00111010 92 93 1 1 1 0 94 95 0 2 0 96 97 4 0 0 0 0 1 1 0 98 99 4 1 0 0 0 1 1 0 400 401 1 0 1 0 0 1 1 0 102 103 1 0 104 105 10010110 106 107 11010110 108 109 10110110 110 111 1 T 1 10 11 0 112 113 10001110 114 115 De 50 X 0 116 117 4 0 1 0 1 1 1 0 118 119 1 T 1 0 e SE c 120 121 1 0 0 1 1 1 1 0 122 123 LOL X3 124 125 10 11 1 0 126 127 4 131 1
13. e the corresponding function to achieve the auto monitoring purpose The dome camera supports one way alarm input grounded connection available and one way alarm output Any auto run functions can be set and called Wiring ALin alarm input positive ALin alarm input com polarity ALoutA 30 E means alarm out on A side ALoutB means alarm out on B side Note The alarm has highest priority For example if Cruise set to run at 12 00 and at the same time an alarm signal input the dome camera would respond to the alarm first ALARM IN 1 Set the alarm input and the dome s corresponding action Following options are applicable e Off or choose one function of Preset Tour Pattern and Auto when alarm e RELAY 1 OFF Turn off the alarm output the alarm will not be activated ON Turn on the alarm output the alarm will give an alarm signal when activated ARM DISARM The alarm system effective DISARM The alarm system is not effective INTERVAL gt Set the alarm interval time from 0047255 seconds 4 10 LANGUAGE Main Menu LANGUAGE LANGUAGE English BACK EXIT Language move the cursor up and down to choose language press the left direction key to confirm 31 4 11 IR SET Main Menu 2 IR SET IR MODE AUTO IR ZOOM SET 1 006 IR ZOOM SET 2 010 PRESENT LUX 010
14. et is skipped SAVE AND BACK gt Save the tour and back CANCEL AND BACK gt Quit without saving and then exit to the upper menu 4 7 3 PATTERN Main Menu AUTO RUNNING PATTERN PATTERN NUMBER 001 RECORD RUN BACK EXIT There are max 4 patterns and the dome camera can record all regular operation in 3 minutes at least The command will drive the speed dome runs as given route repeatedly 9 PATTERN NUMBER gt Set current pattern number from 001 004 lt RECORD gt Edit the current pattern s running route and record all operation in 3 minutes at least CALL PRESET 1 TO BACK CONFIRM 1808 000 RECORD 1805 Remaining record time 00096 The recording space The record time will decrease while the space increases User can call preset 1 to back to the upper menu Notice Any of the time and space is finished even not call preset 1 the recording is end and exit and saved the recording e lt RUN gt Run current pattern repeatedly until other command received 4 7 4 360 SCAN Main Menu AUTO RUNNING 360 scan 360 SCAN DWELL 0S PAN SPEED HIGH RUN BACK EXIT 360 SCAN DWELL gt 0S 360 continuous scan 5S 90 intermittent scan then dwell on 5s the dome will continuously run at the given route repeatedly until receiving new command 10S 90 intermittent scan then dwell on 10s the dome will continuously run at the given route re
15. le image according to the brightness of the center point Thus backlight compensation can increase the brightness of the objects in the center of the picture Select BLC SET and choose the right key to access the sub menu as below BLCQTY 000 WDR OFF BACK EXIT BLC QTY Adjust the data of the BLC choose from 000 255 WDR ON and OFF the camera s WDR function Not supported Advanced Camera Menu For advanced Menu Call preset 69 PLEASE NOTE Scrolling and changing values in the advanced menu is done with different controls 1 Thecontroller joystick has effect 2 Scrolling up and down is done by pressing IRIS IRIS 3 Changing Values of the selected feature is done by pressing ZOOM ZOOM IMPORTANT Changing any values except of in the lt DSP SETTINGS gt menu will result in the camera malfunctioning sjh DSP Settings FOCUS AUTO ID DISPLAY OFF CAM ID 1 PROTOCOL VISCA BAUD RATE 92600 485 CONTROL NORMAL LED 1 8 LED 2 15 lt DSP SETTINGS gt LANGUAGE RESET EXIT SHUTTER WB MODE AGC DNR BACKLIGHT HLC LEVEL MIRROR BRIGHTNESS SHARPNESS lt MASK SETTING gt COLOR EXIT lt SHUTTER gt Choosing between Auto and Manual WB MODE gt White Balance is normally compensated for by the automatic white balance gain control In some lighting conditions user may want to manually adjust the red and blue settings for optimal viewing There are 6 options AUTO Auto White Balan
16. le to bear 4 times the weight of the PTZ and its accessories 3 3 DIP Switch Setting 1 Default Settings Pelco P D auto detected baud rate 2400 address 1 Use Philips screwdriver to remove the DIP switch cover see location below DIP Switch Position Reset Position 2 Baud Rate Setup Decoder Switch 9710 1 ON O OFF Switch 9 10 setting Max transmission Baud Rate 9 10 distance M 0 0 2400BPS 1800 1 0 4800BPS 1200 0 1 9600BPS 800 Auto detected 2400 1 1 4800 9600 600 1800 19200BPS 3 When the DIP Switch 9th and 10th are ON the PTZ can automatically detected the baud rate 2400 4800 9600 19200 4 Hardware Address Setup Please refer to Appendix I Please note that the address setting can also be configured via the software using the camera OSD Page 11 7 AA 4 Setup of the OSD Menu 4 1 Display Boot UP Info Before installation please check the protocol baud rate address and RS485 data cable Default protocol PELCO D address 1 baud rate 2400 PROTOCOL PELCOPD BAUD RATE 2400BPS CAMERA ID 001 CAMERA S N 0000000001 VERSION V1 02 FAN SPEED 6000RPM STARTING When starting the PTZ will display the following information Level self check Success Vertical self check Success Camera type Success Once done the above information will disappear and the user will gain control o
17. lify from 01 32x Notice The above two functions is not available at present e PROPORTIONAL P T gt The dome moves at a certain speed degree per second While zoomed in the default movement speed may become too fast This function decreases the dome movement speed while zoomed in for easier control on the dome f PA e SET NORTH gt User can set orientation by using joystick to position north When select SET NORTH following menu will pop up CALL PRESET 1 TO RETURN CONFIRM Adjust the lens to desired position and call preset 1 to confirm and return 4 7 AUTO RUNNING Main Menu AUTO RUNNING PRESET TOUR PATTERN 360 SCAN ZONE PARK TIME PARK ACTION OFF BACK EXIT 4 7 1 PRESET Main Menu AUTO RUNNING PRESET PRESET NUMBER 001 TITLE PRESET 001 SET CURRNET REMOVE CURRENT BACK EXIT In this function the values of the pan tilt positions will be stored in the desired memory slot so that you will be able to call it when in need 128 presets can be saved It could also setup by shortcuts of control system e PRESET NUMBER Display current preset number the value ranges from 001to 064 Except preset 33 and 34 and 101 to 164 Note Presets 33 34 has other functions in PELCO protocols so the user cannot save any information on it e TITLE To set current preset title 16 bit can be set by the number 0 to 9 and the letters A Z of any combinatio
18. n e SET CURRENT Select this item to set the preset position and zoom The following menu will pop up when Set Current is selected f 23 PA CALL PRESET 1 TO BACK CONFIRM Move to the desired position and zoom to a suitable level call preset 1 to save the current preset and return REMOVE CURRENT Delete the preset with the number and title display above 4 7 2 TOUR Main Menu AUTO RUNNING TOUR TOUR NUMBER 001 DWELL 003 EDIT RUN BACK EXIT The dome camera will run repeatedly as the given sequence of presets at certain dwell time by one command Max 4 tours available 27preset tour 9 TOUR NUMBER gt Set current tour number from 0017004 lt DWELL gt Set the default dwell time from 0007255 seconds for each preset User can still set independent dwell time for each preset when editing the tour X EDIT Edit presets and corresponding dwell time in a tour as follows f 4 PP PRESET DWELL 000 003 000 003 000 003 000 003 000 003 000 003 000 004 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 000 003 SAVE AND BACK CANCEL AND BACK There are three group numbers the left side is preset number the right side is dwell time tour from left to right up to down in the order to run preset when the preset number is set to lt 000 the current pres
19. peatedly until receiving new command e PAN SPEED High 20 S Middle 15 S Low 6 S Auto Doasthe camera s proportional P T speed e RUN The dome will continuously run at the given route repeatedly until receiving new command 4 7 5 ZONE Main Menu AUTO RUNNING ZONE TITLE RGEIN LEFT LIMIT RIGHT LIMIT PAN SPEED HIGH REMOVE CURRENT RUN BACK EXIT lt TITLE gt To set current zone Name 16 bit can be set up by the number 0 9 and the letters A Z of any combination LEFT LIMIT Set the right edge of region lt A gt CALL PRESET 1 TO BACK CONFIRM Move the camera left limit position to confirm and return The position of the left limit position will now be marked on the menu screen 9 RIGHT LIMIT Set the right edge of region B CALL PRESET 1 TO BACK CONFIRM Move the camera right limit position to confirm and return The position of the right limit position will now be marked on the menu screen e PAN SPEED High 20 S Middle 15 S Low 6 S Auto Do as the camera s proportional P T speed REMOVE CURRENT Delete current zone 9 RUN Start current zone scan repeatedly before receiving new command Note PTZ default tour scan direction clockwise direction starting from the left limit If the user finds out the route is wrong he could call number 82 preset again when the tour scan run to the critical point PTZ will scan in the reverse direc
20. reboot the system RTC TIME SET Set the present date and time lt RTC TIMER RUNNING Schedule actions for specific date and time 4 3 1 SITE INFO NAME GXAAF DOME 001 DOME ID OPT SOFT SOFTWARE ID 001 HARDWARE ID 000 BROADCAST ID 255 BACK EXIT Main Menu SYSTEM gt SITE INFO gt NAME The title name of the dome Assigning a name to a dome helps the user to identify which dome is under control for multiple domes site Max 16 digits Setting with number from 0 9 and letter from Move the cursor to SITE ID and then move the joystick right to enter dome ID setting e DOME ID OPT gt Setting the address method that controls the dome user can choose from SOFT Software and HARD Hardware SOFT when choose this the SOFTWARE ID is effective while the HARDWARE ID is ineffective HARD when choose this the HARDWARE ID is effective while the SOFTWARE ID is ineffective e SOFTWARE ID shows the current software ID user can modify and choose address in the range of 0017254 HARDWARE ID shows the current physical ID it is decided by the DIP Switch only user cannot modify via the OSD e BROADCAST ID shows the current ID The ID functions the same as dome s SORTWARE HARDWARE ID The dome works when receives any of those ID The dome s broadcast ID is 255 and cannot be modified BACK return to upper menu EXIT exit the menu 4 3 2 DISPLAY SET UP l
21. s Call 84 preset Start Pattern 1 Call 85 preset Start Pattern 2 Call 86 preset Start Pattern 3 Call 87 preset Start Pattern 4 Call 88 preset Call cruise 1 default number 1716 preset Call 89 preset Call cruise 2 default number 17 32 preset Call 90 preset Call cruise 3 default number 35 48 preset Call 91 preset Call cruise 4 default number 49764 preset Call 92 preset Set left limit Position Call 93 preset Set right limit Position Call 494 preset Camera IR CUT switch Call 95 preset Open main menu Call 97 preset Call all valid presets cruise Call 98 preset Call 360 scan Call 99 preset Preset Error Correction APPENDIX III Trouble Shooting Troubles Reason Solution 1 The power supply is not 1 Correct the connection No action when power on connected correctly 2 Check the power supply LED 2 The fuse is broken power indicator 3 Replace the fuse 1 The dome DIP switch 1 Confirm DIP settings on camera Self testing and image are setting is incorrect power up screen normal but the dome is out 2 85485 cable is 2 Reset the DIP Switch according of control disconnected or reversed to the DIP switch chart 3 Control device is not 3 Check the wiring properly configured 4 Check the control device settings 1 RS485 communication 1 Connect 1200 resistor to the Some function i
22. s out of signalis not balance RS485 line control 2 Control protocol is not 2 Change protocol type compatible Unclear image 1 Focus is in manual state 1 Reset the focus mode to Auto 2 Digital Zoom is on and in 2 Cancel reduce digital zoom full ratio If applicable 3 Clean the dome cover 3 Dome cover is dirty 1 Camera is in Color mode 1 Reset the day night function to No night vision 2 backlight on the top or Auto back of the dome camera 2 Remove the direct light source f 40 PA Nou you can see Ultra Z IR PTZ gives you even more of everything It is faster More accurate Easier for installation and its video Performance is better than ever even in complete darkness
23. t Main Menu SYSTEM DISPLAY SETUP SITE NAME OFF PRESET TITLE OFF PATTERN NAME OFF ZOOM OFF ORIENATATION OFF TEMPRETURE OFF ZONE NAME OFF RTC TIME OFF BACK EXIT lt SITE NAME gt Choose to display site name or not lt PRESET TITLE gt Choose to display preset position or not lt PATTERN NAME gt Choose to display pattern name or not ZOOM Choose to display the current zoom or not ORIENTATION Choose to display the current lens direction or not lt TEMPRETURE gt Choose to display the current temperature or not ZONE NAME Choose to display the current zone name or not RTC TIME Choose to display the date and time or not 4 3 3 DISPLAY BOOT UP INFO PROTOCOL PELCOPD BAUD RATE 2400BPS CAMERA ID 001 CAMERA S N 0000000001 VERSION V1 02 FAN SPEED 6000RPM CALL PRESET 1 TO BACK Main Menu SYSTEM DISPLAY BOOT UP INFO Enter into Boot up info displays to check current setup call preset 1 to return to upper menu 4 3 4 PASSWORD Main Menu SYSTEM 2 PASSWORD INPUT PASSWORD CONFIRM dokeleletok PSWD PROTECTION BACK EXIT lt INPUT PASSWORD gt Factory default is 123456 Use the joystick to enter submenu then input the old password If you forget the password after changing please contact Provision ISR support for recovery password The cursor will flash if the old password is correct and then input the new
24. tion 606 4 7 6 PARK TIME The camera will run certain function automatically if the dome is not receiving any command for the specified time 0S PARK TIME OFF 60S PARK TIME ON 60S 120S PARK TIME ON 120S 4 7 7 RUNNING TYPE Choose the type of action that will take place on activation of Park users can choose between Preset Tour or Pattern Note Time running available only if lt IDLE TIME and RUNNING TYPE are both ON state 4 8 PRIVACY MASK Main Menu PRIVACY MASK MASK NUMBER 001 MASK SETUP REMOVE MASK REMOVE ALL MASK BACK EXIT e MASK NUMBER gt Set and edit the current mask zone number from 001 008 e PRIVACY MASK SETUP Enter privacy mask setup to edit and confirm CALL PRESET 1 TO RETURN CONFIRM Call preset 1 to confirm your setup and then you will see below sub menu 9 E CALL PRESET 1 TO RETURN CONFIRM SIZE Using up down left and right key to adjust the size of the mask then call preset 1 to confirm and return e REMOVE CURRENT MASK Remove current mask then the black lump will disappear e REMOVE ALL MASK Remove all mask then all the black lump will disappear 4 9 ALARM Optional function standard camera do not include alarm Main Menu ALARM ALARMIN OFF RELAY 1 OFF ARM DISARM ARM INTERVAL lt S gt 004 BACK EXIT Using an external alarm sensor can activat
25. ver the camera 4 2 Enter the OSD Menu While the camera is in standby condition call preset 95 Call 95 Enter in order to display the main menu Use the Up Down direction to select item or start the configuration Use the Right key to confirm and left key for exit the current setting The Main menu as follows SYSTEM LENS CAMERA PAN TILT AUTO RUNNING PRIVACY MASK ALARM LANGUAGE IR SET EXIT 4 3 SYSTEM Menu Main Menu gt SYSTEM SITE INFO DISPLAY SETUP BOOTUP SCREEN PASSWORD SET DEFAULT SYSTEM REBOOT RTC TIME SET RTC TIMER RUNNING BACK EXIT System info includes following settings e lt SITE INFO In this menu the user can setup the dome s name View the Hardware address change the camera software address and choose the leading command Hardware or Software X DISPLAY SETUP gt In this menu the user can choose which details will display on the camera Screen The available options are Site name Preset title Pattern name Zoom Orientation Temperature Zone name and RTC time DISPLAY BOOT UP INFO User can view the boot information PASSWORD User can setup or change menu access password SET DEFAULT All settings will go back to factory default Preset positions will be retained 9 SYSTEM REBOOT gt After change dome ID or adjust deviation between two preset positions user this to remotely

Download Pdf Manuals

image

Related Search

Related Contents

EViews 5.1 User's Guide - FOBTECH Remote Services  Mode d`emploi Revécu Sensoriel – Juin 2014  Scorpion Manual V1.docx - Old Dominion University  SP25VDP IM 1.1.3  User Manual - Pro Gadget  König CMP-SPUSB50BU loudspeaker  EUROCONTROL  Datasensor S65 Series Color Detection Sensors  シリーズ  Graco 3A1973B User's Manual  

Copyright © All rights reserved.
Failed to retrieve file