Hikvision Digital Technology DS-2CE16C5T-IT1 surveillance camera
Contents
1. HIKVISION TURBO HD Turret amp Bullet Camera User Manual UD 6L0201D1396A01 www hikvision com Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual applies to Type Model DS 2CE56C5T IT1 DS 2CE56C5T IT3 DS 2CE16C5T IT1 T DS 2CE16C5T IT3 DS 2CE16C5T IT5 This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual Please refer to the product specification for camera parameters and functions 0100001040420 Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits fora digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in acommercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at2. assembly parts are included Make sure that all the related equipment is power off during the installation Check the specification of the products for the installation environment Check whether the power supply is matched with your power output to avoid damage Please make sure the wall is strong enough to withstand three times the weight of the camera and the mounting elf the wall is the cement wall you need to insert expansion screws before you install the camera If the wall is the wooden wall you can use self tapping screw to secure the camera if the product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself 2 1 Installation of Type Camera Steps 1 Drill the screw holes and the cable hole on the ceiling according to the supplied drill template Drill Template Hole 1 for mounting base 1 1 Hole A for cables routed through the wall Figure 2 1 The Drill Template 2 Fix the mounting base to the ceiling with the supplied screws Figure 2 2 Fix the Mounting Base 3 Route the cables to the cable hole and connect corresponding power cable and video cable 4 Secure the camera to the mounting base 5 Fix the enclosure to camera 6 Attach the trim ring to the camera and rotate it clockwise to secure the camera loosely es f S Figure 2 3 Attach the Camera and Trim Ring 7 Adjust t
3. gure 3 7 Detection Area MASKING Select a masking back ground color Select an AREA to enter the masking AREA menu As shown in figure 3 9 AREA Set the status as OFF ON Move the joystick up down and right left to set the horizon vertical size and position As shown in Figure 3 10 MASKING 1 COLOR WHITE 2 AREA NO 0 a 3 AREA NO 1 Fa AREA al 4 AREA NO 2 er m 5 AREA NO 3 m 2 HORIZON SIZE 0 6 AREA NO a 7 AREA NO 5 F 3 VERTICAL SIZE 0 8 AREANO 6 S 4 HORIZON MOVE 0 5 VERTICAL MOVE 0 9 AREA NO 7 ror 0 10 RETURN E Figure 3 8 Marsking Area Figure 3 9 Masking ZOOM IN The ZOOM IN value can be adjusted from 50 to 100 3 3 6 Reset Reset all the settings to the default 3 3 7 Save amp Exit Move the cursor to SAVE amp RESET and press OK to save the settings and exit the menu
4. he surveillance angle according to the figure below coo 0 75 Figure 2 4 3 axis Adjustment 8 Rotate the trim ring to get it fixed with the camera to complete the installation o Figure 2 5 Complete the Installation 2 2 Installation of Type Il Camera Steps 1 Drill the screw holes and the cable hole inthe ceiling according to the supplied drill template 2 Hammer the supplied plastic expansion bolt into the screw holes 2 6 Ceiling Mounting 6 1 1 2 2 1 Screw Hole fo 2 Screw Hole fog Bracket Mounting Base 1 1 Figure 2 6 Drill Template 3 Route the cables to the cable hole and connect the corresponding cables 4 Fix the camera to the ceiling with the supplied screws Adjusting Screw Figure 2 7 Fix the Camera to the Wall 5 Adjust the surveillance angle 1 Loosen No 3 adjusting screw to adjust the pan position 0 360 2 Tighten No 3 adjusting screw 3 Loosen No 2 adjusting screw to adjust the tilting position 0 90 4 Tighten No 2 adjusting screw 5 Loosen No 1 adjusting screw to adjust the rotation position 0 360 6 Tighten No 1 adjusting screw Figure 2 8 3 axis Adjustment 3 Menu Operation MENU i i E DAY VIDEO CO OA S a me aS o CONTRAST SAVE amp EXIT ED ED GO D Em Com MIRROR Figure 3 1 Main Menu E A coaxial camera con
5. his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable C the supplied accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info 1 Introduct
6. ion 1 1 Product Features This camera adopts new generation sensor with high sensitivity and advanced circuit board design technology It possesses the features of high resolution low distortion and low noise etc It is extremely suitable for supervisory system and image processing system The main features are as follows High performance CMOS sensor and high resolution bring high quality image Low illumination 0 01 Lux F1 2 AGC ON O Lux with IR Support IR cut filter with auto switch OSD menu parameters are configurable Support auto white balance auto gain control electronic shutter control and internal synchronization Advanced Engineering Design and patent universal adjustable structure provides convenient adjustment and high reliability SMART IR mode Unit transmission control Advanced 3 axis design meets different installation requirements lngress protection IP66 1 2 Overview 1 2 1 Overview of Type I Camera Enclosure Camera Mounting Base AWAY nN Wun HD Video Cable Figure 1 1 Overview of Type I Camera 1 2 2 Overview of Type Camera HD Video Cable Figure 1 2 Overview of Type ll Camera rE MITE The HD video output mode is set as the default You can short the white and black line end of the switch cable to switch the mode as CVBS output 2 Installation Before you start Please make sure that the device in the package isin good condition and all the
7. n in Figure 3 4 3 3 4 Video Setting Move the cursor to the VIDEO SETTING and press the menu button to enter the video configuration interface As shown in Figure 3 5 CONTRAST Set the CONTRAST value from 1 to 10 SHARPNESS Set the edge and detail sharpness value from 1to 10 COLOR GAIN Set the color gain from 1 to 10 3D NR Set the 3D NR level as High Middle and Low Select OFF to disable the 3D NR MIRROR Set the mirror mode as OFF H V orHV VIDEO SETTING FUNCTION 1 CONTRAST 1 10 1 DETECTION 2 SHARPNESS a 2 MASKING a 3 COLOR GAIN 1 10 3 ZOOMIN 50 100 4 3D NR OFF 4 LANGUAGE ENGLISH 5 MIRROR OFF 5 RETURN a 6 RETURN Figure 3 4 Video Settings Figure 3 5 Function 3 3 5 FUNCTION You can set DETECTION MASKING ZOOM IN and LANGUAGE of the camera in this menu As shown in Figure 3 6 DETECTION Set the motion sensitivity as WEAK LOW MIDDLE or HIGH Select an AREA to enter the motion detection AREA menu As shown in Figure 3 7 AREA Set the status as OFF ON Selecta color for area border Move the joystick up down and right left to set the horizon vertical size and position As shown in Figure 3 8 AREA DETECTION 1 1 SENSITIVITY HIGH STATUS OFF 2 COLOR WAITE 2 AREA NO 0 3 HORIZON SIZE 0 3 AREANO 1 A ARFANO2 4 VERTICAL SIZE 0 SSSR a 5 HORIZON MOVE 0 6 RETURN a 6 VERTICALMOVE 0 l 7 RETURN Figure 3 6 Detection Fi
8. troller purchase separately is required to select the menu and adjust the camera parameters 3 1 VIDEO OUT PAL or NTSC is selectable 3 2 LANGUAGE English and Chinese are selectable 3 3SETUP 3 3 1 AE Move the cursor to AE and you can adjust the image brightness by the BRIGHTNESS AE MODE AGC and SENS UP in this menu As shown in Figure 3 2 BRIGHTNESS Set the brightness value from 1 to 10 to darken or brighten the image AE MODE Set AE mode as GLOBLE AE and D WDR AGC HIGH MIDDLE and LOW can be set for the AGC level Select OFF to disable the AGC SENSE UP Set the SENSE UP value as 0 2 4 8 10 12 14 and 16 AE 1 BRIGHTNESS 1 10 2 AE MODE DWDR MANUAL 3 AGC OFF 1 R GIAN Po A SENSEUP 0 16 2 B GAIN ae 5 RETURN a 3 RETURN Figure 3 2 AE Figure 3 3 Manual of WB 3 3 2 WB Move the cursor to WB and you can set White Balance mode as AUTO and MANUAL in this menu AUTO white balance is being adjusted automatically MANUAL Set the R GAIN B GAIN value from 1 to 10 As shown in Figure 3 3 3 3 3 DAY amp NIGHT Move the cursor to DAY amp NIGHT and select COLOR B W or SMART as the DAY amp NIGHT mode COLOR The image is colored in day mode all the time B W The image is black amp white all the time and the IR LED turns on in the low light conditions SMART Select to turn on off the INFRARED_LAMP and to set the Smart IR level from Oto 5 As show
Download Pdf Manuals
Related Search