Home

Braun Photo Technik Scouting Cam BLACK300

image

Contents

1. ur 4 1 9 Set Video Size This parameter also has four values 1080P 720P WVGA and QVGA The default value is 1080P the following shows how to set it to be WVGA video size a Press MENU to display the setting menu b Press DOWN to select Resolution c Press RIGHT to select WVGA d Press OK to save the current setting then press menu to return to info display e Press MENU to cancel setting and return to info display 4 1 10 Set Date and Time You can change the date and time of the device by setting this parameter when necessary e g after every battery change The date format is day month year the time format is hour minute second The valid value for year is between 2010 and 2050 Provided that the date and time are needed to be set to November 15th 2011 and half past ten the steps are as following a Press MENU to display the setting menu b Press right enter into system c Press DOWN to select Date Time d Press Right to Display Date Time Interface Press UP and DOWN to change the Value e Press OK to save the current setting then press MENU to return to info display f Press MENU to cancel setting and return to info display 4 1 11 Set Multi This parameter affects the number of pictures taken for each triggering in the camera mode It has four values 1 Photo 3 Photos 6 Photos and 9 photos Its default value is 1 Photo The following shows how to set photo burst to 3 P
2. batteries with 1 5V output can be used 1 High density and high performance alkaline batteries Recommended 2 Rechargeable alkaline batteries 3 Rechargeable NiMH batteries A Risk of explosion in case of incorrect changing of batteries or use of wrong type of batteries Never expose batteries to excessive heat such as direct sunlight fire etc as otherwise danger of fire and explosion When in Test Mode camera will be automatically shut down to save power if without any operation within 3 minutes it could be waked up by any movement detection When in low battery state camera will be also automatically shut down Please change the batteries in time 3 2 Insert the SD card Insert SD card into the card slot with marked side upwards Please note that the SD card can only be plugged in one direction 3 3 Power on and Enter into the ON Mode Before switching on please pay attention to the following 1 Avoid temperature and motion disturbances that could be construed as animals or humans such as trees that are exposed to direct sunlight for much of the day or any other heat source These may cause false triggers 2 The height from ground for placing the camera should be one meter higher than object one to two meters height are preferred Slide the power switch to the ON position to power on the camera and enter into the ON mode The motion indication LED red will blink for about 15s The 15s is a buffering time before automat
3. 9 meters 2 3 1 Navigating Press UP or DOWN to select or highlight the menu item while press LEFT or RIGHT to select the option of each item and press OK to make selection Select ltem UP Display Menu Exit MENU Cancel Select Option y v io Te Left abc S3def RIGHT v Select Item DOWN 2 3 2 Laster Pointer Press the punctuation for laser pointer 2 4 Shooting Information Display When the camera is turned on the power switch is slid to TEST position the shooting information will be displayed in the monitor 3 Image Size 2 Camera Mode fy 7 J 4 Battery Level 1 SD Card 07 09 201 s bate M D Y 14 30 28 m 6 Time H M S 0000 0036 7 Available Picture space 2 5 Supported Format File Format FAT32 You dont need to concern about the file system format of the camera unless you have problems with reading the SD card by your other equipment If this happened please format the SD card in the camera or in a computer at first and then reinsert the card into your camera to make a try 3 Easy Operation 3 1 Power Supply To supply power for the camera eight AA size batteries are needed Open the bottom cover Confirm that the power switch is at the OFF Right position pull out the battery depot Load the fully charged batteries into the depot according the polarities sign shown below Push back the battery compartment to the battery chamber The following
4. IEOSIZE u a ee are 11 A ISA A a e a 11 ES A AAA oe PP A 12 A A EET T 12 4 A3 Set Video Lendthe2s un na aieniedee laces 12 Aili Ck Video Sound er ee einge 12 4 1 19 Ser DEA iira E a 12 A MAO SOL TME ru 13 Adel Enter a WO isaac 13 A A A 13 4 2 1 VIEWING Photo or Video viii il 13 4 2 2 Delete Photo OF VideO u ll 14 4 37 LaSer PONEI wasser drid 14 4 2 FIG NUDO essa et 14 4 5 Firmware Upgrade ccccccccsscccsecceececeeecceeeceueesseeeeeeessuseseeeseeeeseeesaeeessaeens 14 Appendix Technical Specifications ccccssecsessesceseecenseeceneeeeneesenseseeneesenees 15 1 Caution A 1 Do not drop knock or shake the camera 2 The working voltage of the camera is 6 0V The camera is supplied by eight AA batteries 3 Remove batteries from camera if camera is not be used for some time 4 Only use a power supply not supplied with the rated input voltage 6V min 500mA specified on the rating plate as otherwise danger of fire and electrocution 5 Please unlock the write protect before inserting the SD card 6 Please insert the SD card when the power switch is at OFF position before testing the camera 7 Please do not insert or take out the SD card when the power switch is at ON position 8 It is recommended to format the SD card by the camera when used at the first time 9 The camera will be in USB mode when connected to an USB port of a computer In this case the SD card functions as a removable d
5. PIR works all the time and media is taken almost continuously The maximum interval is 30 minutes it means the PIR will be disabled for 30 minutes after each triggering The default value is 5 seconds The following shows how to set PIR Triggering Interval Time as 1 minute provided 12 that previous option is 5 seconds a Press MENU to display the setting menu b Press DOWN to select Delay c Press RIGHT to enter in to the interval setting d Press DOWN to select 1 minute e Press OK to save the current setting then press MENU to return to info display f Press MENU to cancel setting and return to info display 4 1 16 Set Timer This parameter defines a certain time lapse in a day when the Camera can be triggered In the rest of the time the device is shut off The effective value of the hour ranges from 0 to 23 while the minute ranges from 0 to 59 Provided that the camera should work from eight a m to five p m the steps are as follows a Press MENU to display the setting menu b Press DOWN to select Timer c Press RIGHT to select item press UP or DOWN to change the value until the start time changes to 8 and the stop time changes to 17 d Press OK to save the current setting then press MENU to return to info display e Press MENU to return to previous menu 4 1 17 Enter Password If the password setting is selected as On after switching on the camera the LCD screen on camera will prompt to enter password The default pa
6. Video and Camera Video The way to set the camera mode is via setting menu The following shows how to set camera mode to Video provided that the previous option is Camera a Press MENU to display the setting menu b Press DOWN to select Mode c Press RIGHT to select Video d Press OK to save the current setting e Press MENU to cancel setting and return to info display Sr SA Sr 4 1 7 Format SD Card The system will delete all images or videos stored in the SD card after formatting make sure that you have made a backup of important data a Press MENU to display the setting menu b Press RIGHT to select System setting c Press DOWN to select Format 10 d Press RIGHT to select SD Card e Press OK to choose Enter to enter into submenu f Press down to select OK OK will be highlighted g Press OK to start formatting the SD card During formatting the display screen will show a message Please Wait h Press MENU to cancel setting and return to info display 4 1 8 Set Photo Size This parameter has three values 12MP 8MP and 5MP The default value is 5 mega pixels The following shows how to set pixel size as 12M Pixel a Press MENU to display the setting menu b Press DOWN to select Resolution c Press Right to select 12M Pixel d Press OK to save the current setting then press menu to return to info display e Press MENU to cancel setting and return to info display Sr gt or
7. a high sensitive Passive Infrared PIR motion sensor and then automatically captures high quality pictures up to 12MP or records 1080p HD video clips WVGA or QVGA At sunrise the unit begins to take color photos and video until there is insufficient light dusk when it begins to take infrared monochrome photos and video It is easy to use there is a 2 0 inch colorful LCD display on camera It is resistant against water and snow for outside uses 2 1 Camera Body Interface The camera has the following I O interfaces USB connector SD card slot TV output and external DC power connector 2 2 Camera components and features 1 Bottom Cover 2 SD Card Slot Memory card must be inserted to store photos or videos 3 Mini USB connection USB 2 0 For connecting the camera to a computer to download photos and videos 4 TV output TV Out The camera can be connected to the AV input of your TV using the supplied AV cable in order to show the monitor image External power supply can be connected via the DC IN socket 6V min 500 mA not supplied 5 PIR Passive Infrared Sensor 6 Infrared LED Flash 1 8 2 inch color LCD Display 9 Sound recorder 0 Lock 1 Power switch ON TEST OFF 2 Battery Depot 2 3 Remote Control The remote control is an input device of the camera and is primarily used for customer settings and password input This is an infrared type wireless remote control The maximum remote distance is
8. hotos provided that the previous option is 1 Photo a Press MENU to display the setting menu b Press DOWN to select Multi c Press RIGHT to select 3 pictures d Press OK to save the current setting then press MENU to return to info display e Press MENU to cancel setting and return to info display 4 1 12 Set ISO This menu could only help you get a better photo at night there are 3 values 100 200 400 a Press MENU to display the setting menu b Press DOWN to select ISO400 c Press OK to save the current setting then press MENU to return to info display d Press MENU to cancel setting and exit 4 1 13 Set Video Length The following shows how to set video length to 30 Seconds provided that the previous value is 10 Seconds a Press MENU to display the setting menu b Press DOWN to select Video Length c Press OK to save the current setting then press MENU to return to info display d Press MENU to cancel setting and exit 4 1 14 Set Video Sound The following shows how to turn off the sound of the video a Press MENU to display the setting menu b Press DOWN to select Voice c Press RIGHT to display the VOICE setting Interface 4 1 15 Set Delay This parameter means that how long the PIR Passive Infrared motion sensor will be disabled after each triggering in ON mode During this time the PIR of the device will not react to the motion of human or animals The minimum interval is 5 seconds it means the
9. ic capturing photos or videos e g for closing and locking the bottom cover fixing the camera on a tree and walk away In ON mode the camera will take pictures or videos automatically according to the default settings or previous custom settings The camera has the sound recording function so the sound will be embedded in the video clip while capturing a video 3 4 Enter into the TEST Mode Slide the power switch to the TEST position to enter into the TEST mode There are some functions in TEST mode Custom settings manual capture preview 3 4 1 Custom Settings Press the MENU switch to enter into menu setting The camera can be taken over control to manually customize the camera settings which display on the camera or external TV monitor The detailed operations will be described in Advanced Operations chapter 3 4 2 Manual Capturing You can press OK to manually capture photos or recording video 3 4 3 View Images or Videos There are two ways to view the captured images or videos 1 LCD screen on camera 2 TV monitors which connects to camera with TV cable Turn right the select switch to view images the latest image will be shown in the LCD screen on camera or TV monitor Press UP to view the previous image and press DOWN for the next The detailed operations like deleting images or videos will be 7 described in Advanced Operations chapter 3 5 Power Off Slide the power switch to OFF position to power off the ca
10. isk 10 Please ensure sufficient power when having firmware upgrade otherwise the upgrade process could be interrupted incorrectly If any fault occurs after improper upgrading process the camera may stop function properly 11 Damage to the electronics housing and display caused by external influences such as heavy jerks electric shocks having fallen or others aren t covered by the warranty 12 Don t dismantle or repair the camera If repair is required ask an expert or technical service centre 13 Keep the camera out of reach of children Attention Legal and privacy protection Please inform yourself carefully about the legal regulations in your country concerning to data protection personal identification copyright duty of notification and privacy laws before using this device The Braun Photo Technik GmbH assumes no liability for violations against the Federal Data Protection Act and other legal regulations Privacy of individuals must be preserved Prepare your camera only at places where this is guaranteed Recordings with people have to be deleted if there is no agreement for publishing The area of recording has to be displayed clearly to all public entry points 2 Instructions Thank you for purchasing BRAUN Scouting Cam BLACK300 This camera is a surveillance camera working automatically It can be triggered at once by any movement of human or animals in a certain region of interested ROI monitored by
11. mera Please note that even in the OFF mode the camera still consumes certain power at UA level 4 Advanced Operations From the basic operations of the camera in previous chapter we know that the camera has three basic operation modes Power switch 1 OFF mode Power switch is at OFF position Right 2 ON mode Power switch is at ON position Left 3 TEST mode Power switch is at TEST position Middle In the above three modes the OFF mode is the specified safe mode when replacing the SD card or batteries and transporting the camera The settings can only be customized in TEST mode and the remote control is needed 4 1 Settings Menu To view the camera settings menu press MENU in the TEST mode called settings menu in this chapter The settings menu will be shown on the LCD on camera or the external TV monitor 4 1 1 Photo Setting 4 1 2 Video Setting 4 1 3 System Setting 4 1 4 Default Camera Video CameraBVideo Resolution Camera 12M 12M 8M 5M ISO 400 100 200 400 Resolution Video 1080P 1080P 720P WVGA QVGA Video Length 10s 30s 60s 90s Same as last time YY MM DD MM DD YY DD MM YY Adjust English French Germany Spanish and Language English Russian 4 1 5 General Settings The operating steps are suitable for following menu items Camera Mode Photo Size Video Size Multi Video Length Delay Timer 4 1 6 Set Camera Mode There are three camera modes Camera
12. o the camera 4 Power on the camera Test Mode 5 The camera will read it and update itself automatically When updating the 14 camera its screen is black 6 The screen will light on after being finished 7 Plug out the SD card then insert it into pc delete the FW18NA bin in the SD card If you don t do this the camera will enter update mode when power on again 8 Insert the SD card into the camera for its working Appendix Technical Specifications sm x 80mm x 55mm Reiter FuilAutomatleiRFilter ri TFT Display 2 0 Color TFT LCD Pin sensor angle of detection OUP PTiggertime O seconds CO meroma PRA OOO Password Security 4 digital numbers Stand by time TV out NTSC PAL USB SD Card Holder 6V DC External Belt on tripod Operation Temperature 30 70C Power Supply 8 x AA batteries Security authentication FCC CE RoHS Included Digital Camera Wireless controller USB Cable TV cable CD Manual Yes 15
13. r delete all d Press OK Cancel and OK are prompted e Press OK to delete the image or video f Press cancel to cancel then press MENU and OK to return to info display Please note that after deleting a picture or a video file the deleted files can t be restored Furthermore in order to delete all the images and video clips in the SD card it is suggested to format the SD card Sr m u 4 3 Laser Pointer The laser pointer can be turned on and is especially useful when it is somewhat dark as an additional function for pointing to an object or a certain region of interested ROI Press to turn on the laser light in TEST mode and use the tilt adjuster on the back of camera to adjust the angle of capturing direction WARNING Please note that the laser could be harmful to the eyes if pointed at other person 4 4 File Numbering Images and videos are separately saved in the pre named folder 104MEDIA File numbering continues by adding one to the last number for each new image or video The saving name is like PTDC0001 JPB or PTDC0001 AVI Through the suffix you can distinguish whether the file is an image with suffix jog or a video with suffix avi 4 5 Firmware Upgrade This camera is equipped with an automatic upgrade function for you Upgrading is needed only when an improved firmware is available The operations are as following 1 Unzip the update file 2 Copy the FW18NA bin to SD card 3 Insert the SD card int
14. scouting Cam BLACK300 Instruction Manual RS NA OE EOI oe ED in E ie DIR en BS B te BRAUN PHOTO TECHNIK GmbH KlingenhofstraBe 72 90411 N rnberg www braun phototechnik de 4 Inhalt AUN ral 3 2 INSTUCUIONAS dd 4 2 1 Gamer BOV Interface ae u I 4 2 2 Camera components and features 222u002400020nnenennennnnn nenne nennen nenne nennen 4 2 3 Remote GOTO 5 2 3 1 Navidad iii 5 2 3 2 E O nee ie 5 2 4 Shooting Information Display 2u0224002020020n nenn E nenn name nenne nennen 5 2 5 SUDDOMCG Formal ota 6 3 EASY OPC FatlO N ai e e A abet errechnen 6 Sal O SUDD Y AAA PP 6 9 2 Insert HESD eAald urenee ee ne nie 7 3 3 Power on and Enter into the ON Mode s2220022200200000n0 none nenne nennen 7 3 4 Enter into the TEST Mode ccooccccncccncccncconcconoconocononononononanonanonanonanonanonanonoss 7 34 1 CUSTOMS CUMING Srita 7 34 2 Malidal CapuninG xiii Celie foe Sie cee tae 7 3 4 3 View Images or VIdeosS occoocccoccoocccocnoccnconnononccononononanonanonanonanenaninon 7 E E 8 4 Advanced Operations nn nenn 8 AA Setlinds Menu zeiten ee rin eisen 8 AAs PAP 8 41 2 o A A 9 A O SIS a eat 9 O A ner Re Re ae ee EN Te ee ne SS 10 41 5 General Settings rd daa 10 41 6 Set Camera MOC wc cescscecconceveicascscescnasecdtendcaxescnaseeddardcavesceacsestosdenesendcs 10 47127 Formato Cadet 10 41 8 gt SEFPIOIO SI ZB ar nee ne ee ee ee 11 41 9 SELVI
15. ssword is off It can be changed where the steps are as following a Press MENU to display the setting menu b Press DOWN to select Password c Press Up to select On then press Right to select 4 numbers as password d Press OK to save the current setting then press MENU to return to info display e The LCD screen will prompt to enter password next time you switch on the camera f Press MENU to cancel setting and return to previous menu 4 2 Playback In playback mode images or videos can be viewed deleted The images and videos can be viewed on LCD screen on camera and TV monitor which connect to camera with TV cable For simplicity operations with PC won t be introduced here 4 2 1 Viewing Photo or Video a Switch to TEST mode and enter into info display b Press right the select switch to view the latest picture or video in LCD screen 13 on camera TV monitor or Image viewer with TV in connector c Press Left to start playing the video when viewing d Press Left again to stop playing the video e Press UP to view the previous picture or video and DOWN for the next f Press OK to return to info display When viewing images the total number of all images in the SD card and the index of the displaying image will be shown respectively 4 2 2 Delete Photo or Video The operations are as following a Press Right to display Photos and Videos b Press Menu to select Delete c Press right to select delete current o

Download Pdf Manuals

image

Related Search

Related Contents

EVM 210−60  仕様書別紙2  Milwaukee Heavy-Duty 3/8" Hammer-Drills User's Manual  [Download] azionamenti-hcs01  Instructions d`Installation et d`Itilisation Modèle: TLC  LED照明総合カタログ  取扱説明書.pdf  13.0 Diagnostica, software e accessori  

Copyright © All rights reserved.
Failed to retrieve file