Chief K2W110S flat panel wall mount
Contents
1. INTERFACE ROTATION RANGE TEE OU H an E OMAR MOUNTING PATTERN WPA TIBILIT He 11 11 44 Diss K2W Series Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavite a stella Kruiskopschroevendraaier Tournevis a pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl a fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a mao2. 1 Ensure faceplate is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust as required before proceeding See ADJUSTMENT for detail See Figure 3 Using Phillips screwdriver carefully install two M4x14mm screws B into the upper mounting holes on the display Thread screws completely into display then back out 3 complete turns See Figure 3 Pick up and align display so that screws B installed on the back of the display in the previous step fit into the mounting holes on the faceplate Rotate the bracket as required Lower the display firmly into place See Figure 3 5 Figure 3 Using Phillips screwdriver install two remaining M4x14mm Phillips screws B through the lower mounting holes in faceplate into the display See Figure 3 Tighten all four screws B Do not overtighten Recessed Mounting Holes 1 Ensure Centris bracket is able to swivel and tilt easily yet still be tight enough to hold display in desired position Adjust as required before proceeding See ADJUSTMENT for detail Carefully place display face down on protective surface Place the four spacers D over each of the mount holes on the back of the display See Figure 4 Pick up and orient the mount A so that the mounting holes are aligned with the holes in the spacers rotate the bracket as required See Figure 4 Using Phillips screwdri
3. A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option C d y 4 d Hex Head Wrench Llave de cabeza hexagonal Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranca Chiave di sicurezza Veiligheidssleutel Cl de s curit Installation Instructions K2W Series TOOLS REQUIRED FOR INSTALLATION e E 3 16 included 1 8 included A 1 e Arm assembly K2W120 shown single display models dual display models SE J 1 included with C 4 8 D 4 8 M4x25mm M10x5 3x10 K2W models only G 2 1 4 x 2 1 2 H 2 1 4 J2 1 Handle J5 1 9 J6 1 7 2 J8 2 J9 1 Poakel washer 5 16 18 roe SS Thin A Plastic clip washer washer e J3 1 e 16 5 16 18 x d SR J4 1 e Pivot pin L 1 1 8 e J10 1 J11 1 J12 1 Rotational Cable clip Pivot point spacer spacer K2W Series Installation Instructions Figure 1 Assembly And Installation spacer J12 if additional cable management is desired See Figure 2 Connecting
4. INSTALLATION INSTRUCTIONS C Gi K2W220 K2W Wall Mounts i CHIEF K2W Series Our Mounts Your Vision K2W Series Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved A IMPORTANT SAFETY INSTRUCTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the in
5. K2W Series wall mount to Wall 1 Determine mounting location on wall K1W22H shown 2 Use a stud finder to locate 2 x 4 wood stud 3 Use wall bracket E to mark and drill two 1 8 x 2 1 2 holes in wall at desired mounting location See Figure 1 IMPORTANT Only top and bottom holes of wall bracket E must be used to attach bracket to wall as shown in Figure 1 Do NOT use any other holes to secure bracket to wall 4 Use two 1 4 2 1 2 hex head lag screws F and two 1 4 washers G to install wall bracket E onto wall See Figure 1 IMPORTANT Over tightening screws F may cause bracket to compress into soft wall surface resulting in difficult mount installation or improper engaging of set screw in Step 6 5 Hang monitor arm A over wall bracket See Figure 1 6 Secure monitor arm to wall bracket by tightening set screw Ensure set screw engages back side of wall bracket E to properly secure mount See Figure 1 Array Installation K2W21H and K2W22H Models ONLY 1 Slide rotational spacer J10 into opening on array attachment bracket See Figure 2 2 Use 5 16 18 x 3 button head cap screw J3 two thin steel washers J8 plastic spacer J9 pocket washer J5 pivot Fi 2 pin J4 pivot point spacer J12 and 5 16 18 lock nut J6 igure to secure array J1 to K2 arm A See Figure 2 NOTE Cable clip J11 can be used in place of pivot point 8 Installat
6. ace See Figure 8 Figure 8 Handle Installation K2W21 22H models only 1 Loosen four screws securing handle brackets to K2W21H K2W22H array See Figure 9 2 Install uprights of handle J2 into handle brackets located on the back of array See Figure 9 Figure 9 3 Position handle J2 at desired height and secure by tightening button head cap screws attaching handle brackets to array See Figure 10 S Figure 10 Adjustments Portrait Adjustment K2W21 22H Models only 1 The monitor may be adjusted 90 degrees in either direction in order to provide a portrait view of the monitor See Figure 11 2 Use 3 16 hex key L to adjust rotational adjustment screw to adjust rotational tension See Figure 11 portrait tension Figure 11 11 K2W Series Installation Instructions Adjustments K2W21H 22H models only 1 Loosen knobs securing faceplates to array See Figure 12 2 Slide displays laterally on array to adjust lateral shift See Figure 12 Adjust pitch and pivot position as desired See Figure 12 Tighten knobs to secure faceplates in position See Figure 12 Figure 12 Array Bar Roll Adjustment 1 Loosen roll adjustment screws on back of array bracket See Figure 13 Adjust roll of array bar as desired See Figure 13 Tighte
7. ion Instructions K2W Series Display Installation WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment lt is the installer s responsibility to make sure the combined weight of all components located between the K2W Series Monitor Arm up to and including the display does not exceed the weight limit listed Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury Max Weight Allowed for EACH Max Weight Capacity of Display Mounting System K2W110 40 lbs 40 lbs 18 14 kg 18 14 kg K2W120 40 lbs 40 lbs 18 14 kg 18 14 kg K2W220 25 lbs 50 Ibs 11 34 kg 22 68 kg K2W21H 15 lbs 30 Ibs 6 8 kg 13 6 kg K2W22H 15 lbs 30 lbs 6 8 kg 13 6 kg K2W110 K2W120 AND K2W220 NOTE K2W21H and K2W22H mounts have K1 Series faceplates on array arms Proceed to K2W21H K2W22H Section The mounting holes on the back of the display will either be flush with the back surface or recessed into the back surface Refer to the applicable installation procedure Flush Mounting Holes A CAUTION Using screws of improper size may damage your display Proper screws will easily and completely thread into display mounting holes A CAUTION Inadequate thread engagement in display may cause display to fall Back out screws ONLY as necessary to allow installation of Centris bracket
8. n roll adjustment screws on back of array bracket See Figure 13 12 Figure 13 Swing Arm Pivot Adjustment 1 Adjust pivot position as desired See Figure 14 2 Adjust pivot point tension screws to change pivot adjustment tension See Figure 14 pivot point tension Figure 14 Installation Instructions K2W Series Cable Management 1 Route cables through cable management channels See Figure 15 Figure 15 Array Models 1 Install cable clips J7 to back of array See Figure 16 2 Route cables through cable clips J7 as desired See Figure 16 Figure 16 13 K2W Series Installation Instructions 14 Installation Instructions K2W Series 15 K2W Series Installation Instructions USA International i CHIEF Our Mounts Your Vision Europe Chief a products division of Milestone AV Technologies Asia Pacific 8800 002483 Rev02 2014 Milestone AV Technologies www chiefmfg com 05 14 Pn 0 Pn 0 P TU 6436 City West Parkway Eden Prairie MN 55344 800 582 6480 952 225 6000 877 894 6918 952 894 6918 Franklinstraat 14 6003 DK Weert Netherlands 31 0 495 580 852 31 0 495 580 845 Office No 918 on 9 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477
9. s 18 14 kg 18 14 kg K2W220 25 lbs 50 lbs 11 34 kg 22 68 kg K2wW21H 15 lbs 30 Ibs 6 8 kg 13 6 kg K2W22H 15 lbs 30 lbs 6 8 kg 13 6 kg SAVE THESE INSTRUCTIONS Installation Instructions K2W Series DIMENSIONS K2W110 2 32 59 0 INTERFACE ROTATION RANGE 9 G PATTERN PA TIBILITY 3 22 me 81 7 o o o o o O lat 14 K2W120 1 38 6 75 34 9 171 5 K2W Series Installation Instructions K2W21H tk ve pag 6 75 171 5 285 72 5 3 13 79 5 TLT RANGE Tor Wy fo 2 0 T o meo AO THI e E LES ET 1 36 3 22 g L 344 81 7 o l A 2 Es f K2W22H a PPa 34 9 aT DNR ey 675 171 5 2 85 Lei 72 5 E E z HP 3 51 i A 89 2 PS y Y 12 32 Io G ee ia TILT RANGE aa lla D Installation Instructions K2W Series K2W220 2 32 59 0 6 75 171 5 1 34 ol to Al E O
10. staller s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING Use this mounting system only for its intended use as described in these instructions Do not use attachments not recommended by the manufacturer WARNING Never operate this mounting system if it is damaged Return the mounting system to a service center for examination and repair WARNING Do not use this product outdoors WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components located between the K2W Series Monitor Arm up to and including the display does not exceed the weight limit listed below Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury Max Weight Allowed for EACH Display Max Weight Capacity of Mounting System K2W110 40 Ibs 40 lbs 18 14 kg 18 14 kg K2W120 40 lbs 40 lb
11. ver install four M4x25mm screws C through the mounting holes through the spacers and into the display See Figure 4 Tighten all four screws Do not overtighten K2W Series Installation Instructions Figure 4 K2W21H K2W22H 1 Remove quick release faceplate from mount by pulling quick release lever and sliding faceplate off mount See Figure 5 for flush mounting holes Y quick release faceplate Figure 6 For recessed mounting hole installation e Place four spacers D on top of mounting holes on back of display See Figure 7 e Using Phillips screwdriver carefully install four M4x25mm screws C through corresponding holes on faceplate spacers D and into the mounting holes on the display See Figure 7 Figure 5 Carefully place display face down on protective surface Connect faceplate to display For flush mounting hole installation e Using Phillips screwdriver carefully install four M4x14mm screws B through corresponding holes on faceplate and into the mounting holes on the display See Figure 6 10 for recessed mounting holes quick release faceplate Figure 7 Installation Instructions K2W Series 4 Position display with faceplate attached above mount See Figure 8 5 Slide faceplate onto mounting head until quick release tab clicks into pl
Download Pdf Manuals
Related Search