Chief FPM4200 flat panel wall mount
Contents
1. P Flag may be moved TN Figure 1 Install Mount to Single Wood Stud 1 Determine approximate mounting location keeping in mind the display size Use a stud sensor to locate applicable wood stud Mark location with a pencil Level FPM assembly A at desired height and using it as a template mark the location of upper and lower pilot holes Ensure marks are in the center of wood stud NOTE Mount can provide 1 2 of lateral shift by using mount holes on either side of vertical center line WARNING ELECTRICAL SHOCK HAZARD Drilling into electrical wires or cables can cause DEATH or SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before drilling or installing mount fasteners Drill 1 8 pilot holes Ensure pilot holes are straight Fasten FPM to wood stud using two 10 x 2 1 2 Phillips head screws D through two 10 washers C FPM A and drywall not shown and install into pilot holes See Figure 2 Figure 2 Install Mount to Drywall WARNING Drywall must be a minimum thickness of 1 2 and a maximum thickness of 5 8 Do not install drywall anchors into the seam between drywall pieces 1 Determine approximate mounting location keeping in mind the display size 2 Level FPM assembly A at desired height and using it as a template mark the location of the four anchor holes one in2. O 2 13 moa 1 50 i 4 38 385 Mo D 1 4 x3 8 SLOT Installation Instructions FPM Series LEGEND Apretar elemento de fijaci n Marcar con l piz Befestigungsteil festziehen Stiftmarkierung Apertar fixador VA Marcar com l pis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Aflojar elemento de fijaci n Perforar Befestigungsteil l sen Bohrloch Desapertar fixador Fazer furo Allentare il fissaggio Praticare un foro Bevestiging losdraaien Gat boren Desserrez les fixations Percez un trou Destornillador Phillips Ajustar Kreuzschlitzschraubendreher Einstellen Chave de fendas Phillips Ajustar Cacciavite a stella Regolare Kruiskopschroevendraaier Afstellen Tournevis pointe cruciforme Ajuster TOOLS REQUIRED FOR INSTALLATION 1 8 wood stud 3 8 e 4 10 24 Hollow wall anchor D 2 10 x 2 1 2 A 1 FPM Assembly FPM Series Installation Instructions INSTALLATION The FPM may be installed on either a single 2 x 4 wood stud or on drywall 1 2 minimum thickness The FPM allows a tilt range from 5 up to 18 down NOTE The latching flag may be moved if necessary See Figure 1
3. CH E E USA International Our Mounts Your Vision Europe Chief Manufacturing a products division of Milestone AV Technologies Asia Pacific gt 2011 Milestone AV Technologies 852 2145 4099 PO Duchossois Group Company F 8522145 4477 www chiefmfg com 09 11 4 MY Os O CONSUMER
4. INSTALLATION INSTRUCTIONS Small Flat Panel Tilt Wall Mount CHIEF FPM Series Our Mounts Your FPM Series Installation Instructions DISCLAIMER Milestone AV Technologies its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT WARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions DIMENSIONS WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warr
5. anty Itis the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm Do not install drywall anchors into the seam between drywall pieces WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the combined weight of all components attached to the mount does not exceed 45 lbs 20 4 kg for wood stud installation OR 30 lbs 13 6 kg for drywall installation Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury es O FACE TILTS y 5 UP 18 DOWN 12 MOUNTING BUTIONSON INTERFACE BRAC KET FIT INTO SLOTS ON MOUNT 5 el DIMENSIONS INCHES 1 29 eoh 2235 113
6. each corner slot WARNING ELECTRICAL SHOCK HAZARD Drilling into electrical wires or cables can cause DEATH or SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surfaces is free of electrical wires and cables before drilling or installing mount fasteners Installation Instructions FPM Series 3 Drill 3 8 anchor holes Ensure holes are straight and completely through drywall See Figure 3 07 Anchor x4 CN screws Sy Y y Figure 3 a 4 Gently tap anchor into anchor hole Anchor barbs should be fully engaged in drywall See Figure 4 A Anchor not Drywall Anchor Figure 5 collapsed collapsed Lee Install Display to Mount NOTE Proper interface must be attached to display Follow instructions included with interface assembly 1 Open latching flag by rotating flag clockwise on FPM A H 5 See Figure 6 Latching flag closed Latching flag open Anchor barb Figure 4 5 Using Phillips screwdriver tighten anchor screw until anchor has fully collapsed against back side of drywall See Figure 3 and See Figure 4 NOTE Anchor screw will feel tight until anchor begins to collapse Screw will then turn easier for many turns Screw will feel tight when anchor has fully collapsed 6 Repeat Steps 4 and 5 for remai
7. ning anchors 7 Remove and retain anchor screws from anchors B NOTE Anchors B may come with small washers which may Figure 6 be left on the screw or discarded These small washers do NOT replace washers C 8 Insert anchor screws through washers C FPM A and install into collapsed anchors B Tighten until secure See Figure 5 FPM Series Installation Instructions 2 Lift and maneuver display such that all mounting buttons fit into openings on FPM A See Figure 7 10 Tilt Down 3 Lower display firmly into place Ensure each mounting button has fully seated in the opening See Figure 7 a o 4 Close latching flag by rotating flag counterclockwise on FPM A See Figure 7 Latching flag Display 299 Figure 8 Figure 7 Adjusting Tilt 1 Loosen adjusting screws on each side of display See Figure 8 Adjust tilt as desired Retighten adjusting screws Installation Instructions FPM Series FPM Series Installation Instructions 8401 Eagle Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street 8803 000034 RevD Fotan Shatin Hong Kong IC
Download Pdf Manuals
Related Search