TP-LINK NC200 surveillance camera
Contents
1. 2 Click Manually and you will see the following screen Wireless Network Name Security None pr Connect 3 In the Wireless Network Name field enter the name of the wireless network to which your camera is ready to connect Note The name must be exactly the same as that used in the wireless access point or the connection will not be established Leaving this field blank means the camera will attempt to access the nearest open network If your PC wants to access the camera make sure your PC and the camera are connecting to the same wireless network 4 Select the wireless security mode used by your wireless network from the drop down list The security mode and its corresponding settings must be exactly the same as that used in the 23 NC200 WEIER EREIET TTT wireless network 5 Click Connect and a screen will pop up Click Change on the pop up screen D Click OK on the pop up screen to finish wireless connection procedure 7 To start using camera wirelessly unplug its Ethernet cable 3 4 4 Advanced Wireless Extender On this page you can setup and configure the wireless network extending feature of your camera Wireless extender function allows your camera to extend the range of your existing wireless network The same network name and settings as the existing wireless network can be used or you can create a new one The camera s wireless extender function is disabled by default If you want to use this f2. If the Internet bandwidth is lower than target bit rate the video streaming will not work correctly Use the operating system of the selected language Set the Encoding or the Character Set of the selected language on the Internet Explorer e The traffic of the network and the object of the image affect the frame rate The network congestion causes frame rate slower than the setting Check the bandwidth of Internet connection If the Internet bandwidth is lower than target bit rate the video streaming will not work correctly Ethernet switching hub can smooth the frame rate Default Gateway and DNS server address should be set up correctly If FTP does not work properly ask your ISP or network administrator about the transferring mode of FTP server The lens is dirty or dust is attached Fingerprints dust stain etc on the lens can degrade the image quality To insure the images you are viewing are the best they can be set the Display property setting color quality to 16bit at least and 24 bit or higher if possible within your computer The configuration on the camera image display is incorrect You need to adjust the image related parameters such as brightness contrast and saturation properly Wrong power line frequency makes images flicker Make sure the 50 or 60Hz format of your camera If the object is dark the image will flicker Make the condition around the camera brighter Miscellaneous Cannot
3. 23 TP LINMK_FFFFFF Mone FE FF FF FF FF FF TP LINK_3G_2CBBB4 WPAWYPAZ PSEK OC 82 68 2C BB B4 feng Mone Ag 87 4E F 7 6E 20 3112AC Mone O0 01 56 31 12 AC TP LINK_FIC62C Mone 08 57 00 F9 C6 2C DASE ZE WIPANYPAZ PSk D4 CA4 6D 0A 5F 2F TP LINK_MS_ EC6G12 WIPANYPAZ Pok 5A oF CC EC 6B 12 Wireless Network Mame connect gt Wireless Network Name Displays the wireless network s name Make sure the camera and your PC connect to the same wireless network or your PC can t access the camera gt Signal Displays the strength of the wireless signal gt Security Displays the wireless network s security mode gt MAC Address Displays the MAC address of the front device To connect your camera to a wireless network follow the steps below 1 Click Scan to scan the available wireless network and to refresh the Wireless Network List 2 Select a wireless network from the wireless network list 3 Ifthe wireless network s security mode is None simply click Connect If the security mode is one requiring for a password enter the wireless network s password and then click Connect NC200 WEIER EREIET TTT You can select Show password to display what you ve entered Wireless Connection Enable lt Disable Wireless Network List Gran Wireless Network Mame Signal Security WAC Address TF LINK_1B0F 28 WWPANYPA PSE S4 E6 FC 16 0F 268 TR LINK_3G None O0 0C 43 7 6 16 20 TP LINK_EC amp 823 None O0 04 EC EC 68 253 TP LINK
4. Custom Level find the item Download signed ActiveX controls and check Prompt 4 After the plugin is successfully installed refresh the webpage to display the monitor video TP LINK Cloud Camera 300Mbps WiFi 7 The Reliable Choic NC200 English Logout S Live View Basic Advanced ei System Brightness emm see Contrast emm Ae Saturation m on Resolution 640 480 v 3 2 Live View The Live View screen shows you the live video feed from your camera On this screen you can capture a picture record a video change the resolution and so on NC200 WEIER EREIET TTT v ESS gi Brightness emm Contrast wm Saturation m Preset Resolution 640 480 Vv The image file will be saved in JPG or BMP Click to capture a still format in your local computer The file is named image shot by the camera as image yyyy mm dd hh mm ss jpg You can select a save path and rename the image file The video file will be saved in AVI format in your local computer The file is named as rec yyyy mm dd hh mm ssi avi You can select a save path and rename the video file The icon LY will turn yellow CD once the save path is selected If you want to stop recording just click Last If the camera is installed upside down Flip Image and Mirror should both be checked Click to record the current video Click to vertically flip the current image Normal Mirror image spam Mirror Flip Click
5. IP address which is used to access and configure the camera IP Address Dynamic IP Static IP Fallback IF 19 168 0 10 gt Dynamic IP Select this option when a DHCP server is installed on the network to issue IP address assignment With this setting the IP address of the camera is assigned automatically Fallback IP If the camera cannot get a Dynamic IP address from a DHCP server within limited tries the camera will assign a default IP address 192 168 0 10 by itself as the Fallback IP address 19 NC200 WEIER EREIET TTT IP Address Dynamic IP Static IP MAC Address 00 0C 43 7 6 20 69 IP Address 192 168 1 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 1 Primary ONS Server 172 31 1 1 secondary ONS Server 1r2_ 31 12 gt Static IP Select this option when a static or fixed IP address is obtained for the camera A static IP address will ease your access to the camera in the future Add your camera s static IP information to your router to avoid IP conflicts MAC Address Displays the Ethernet MAC address of the camera The MAC address is read only IP Address Enter a fixed IP address for the camera in dotted decimal notation Subnet Mask Enter the subnet mask in dotted decimal notation The default value is 255 255 255 0 Default Gateway Enter the default gateway in dotted decimal notation Primary DNS Server Enter a DNS address in dotted decimal notation Secondary DNS
6. Network Wireless Connection Cloud Settings LED 3 3 1 Basic Status The Status page displays the current configuration information of the camera You can find out 11 NC200 camera s settings such as wireless connection settings here All the information is read only Camera Name Model Firmware Version Current Viewers Cloud Server Connection Status Username Wireless Connection Status Wireless Network Name Channel Rate Signal Strength Security Network Connection Type MAC Address LAN IP Address Subnet Mask Default Gateway Primary DNS Server secondary DNS Server Status Resolution Frame Rate Image Quality Light Frequency NC 201 NC200 1 0 1 0 13 Build 140513 Rel 16006 0 Connected TF LINK_1B0F28 D 100 WPANMVPA2 PSK Dynamic IP 00 0C 43 7 6 20 69 192 168 171 100 255 255 255 0 192 168 1 1 192 168 1 1 0 0 0 0 640 480 20FPS High auto 12 Cloud Camera 300Mbps Wi Fi NC200 WEIER EREIET TTT 3 3 2 Basic Network On this page you can configure your camera s IP address which is used to access and configure the camera IP Address ei Dynamic IP Static IF Save gt Dynamic IP Select this option when a DHCP server is installed on the network to issue IP address assignment With this setting the IP address of the camera is assigned automatically IP Address Dynamic IP Static IP MAC Add
7. Notification Sending Target k FTP FIP Server Port 1 Usemame Password Path l Passive Mode Ei Test TT E mail Save gt FTP Server Port Enter the IP or the domain IP domain without prefix ftp and the port of the FTP server that you will be connecting to The port is 21 by default L Note The FTP server you set and the camera should be in the same LAN gt gt Username Enter the username that is used to log in to your FTP server Password Enter the password that is used to log in to your FTP server Path Enter the path to the destination on the FTP server Passive Mode Enabling passive mode may help you reach your FTP server if your camera is behind a router protected by a firewall To set up a FTP to receive notification follow the steps below 29 6 T NC200 Boi KTERE Ea Notification Sending Target Wi FIP FTP ServeriPort 192 168 1 168 21 Usemame test Password TIT Path itest Fassive Mode Ba Test C E mail Save Enter an IP address or domain of your FTP server e g 192 168 1 168 Remain the FTP port number as the default value 21 Enter your username to log in to the FTP server e g test Enter your password to log in to the FTP server Enter the path to the destination on the FTP server e g test Enable Passive Mode Click Save to save and enable the settings Click Test and a test JPEG snapshot will be sent to the specified FTP server to check whether y
8. Server Enter a DNS address in dotted decimal notation PPPoE Point to Point Protocol over Ethernet This camera is a PPPoE enabled one It can directly connect to the xDSL however it should be set up in a LAN environment to configure the PPPoE information first and then connect to the xDSL modem Power on again and the camera will dial on to the ISP to get a dynamic IP address and connect to the WAN through the xDSL modem In this case you need to use a domain name to log in to the camera For details please refer to 3 4 6 Advanced DDNS PPPoE PPPoE Enable Disable Status Disconnected Username Password 20 NC200 WEIER EREIET TTT gt PPPoE To enable or disable the PPPoE service here gt Status Displays the PPPoE connection status gt Username Enter the username for PPPoE service provided by your ISP gt Password Enter the password for PPPoE service provided by your ISP HTTP Hypertext Transfer Protocol This feature allows you to access and manage your camera from a remote location over the Internet Web browser access normally uses the standard HTTP service port 80 This camera s default remote management web port number is 80 For greater security you can change the port to a custom one When you have set the HTTP port number to a number other than 80 a corresponding port must be opened on the router Access the camera by typing the IP address of the camera on the Web browser as follows for e
9. or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Note The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment Such modifications could void the user s authority to operate the equipment FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This device and its antenna must not be co located or operating in conjunction with any other antenna or transmitter To comply with FCC RF exposure compliance requirements this grant is applicable to only Mobile Configurations The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co located or operating in conjunct
10. play the recorded file Have installed Microsoft s DirectX 9 0 or later and use the Windows Media Player 11 0 or later to play the AVI filed recorded by the camera 45
11. the IP address of the camera you want to monitor in the address field of the browser CH gt rttp 192 168 1 100 Gl E NC200 Admin Login ER CES 2 Enter the default username and password admin admin Click Login to start the main menu admin CH E eeooeo La Remember account Logn LS Note For the administrator the default password is admin We recommend you to change it in the Account menu Go to System Account If you log in to the camera as an administrator you can perform all the settings provided by the Camera If you log in to the camera as a user you can only view the Live View After logging as administrator you can add up to five user accounts in the Account menu Go to System Account 3 Click Download to download and install the required plugin NC200 WEIER EREIT TTT TIPS x The TP LINK camera plugin is required Please download and install the Camera plugin and manually refresh the page or restart the browser If the installed plugin doesn t work please set your browser security settings to allow plugins LS Note If the installed plugin doesn t work set your browser security settings to allow plugins Here we take the settings for IE browser as an example Go to Tools Internet Options Security Click Internet Custom Level find the item Download signed ActiveX controls and check Prompt Click Local Intranet
12. 00 762069 gt Bonjour To enable or disable the Bonjour service here gt Bonjour Name Displays the Bonjour name By default it is a combination of model and the last six characters of the camera s MAC address Click Save to save and enable the settings 3 4 3 Advanced Wireless Connection The camera s wireless function is enabled by default With this function enabled you can connect your camera to a wireless network wirelessly If you don t want to use this function just select the Disable option On this page you can either scan a wireless network to connect to or enter a wireless network s parameters manually To scan a wireless network refer to 3 3 3 Basic Wireless Connection To enter the parameters manually see the following 22 NC200 WEIER EREIET TTT EREECHEN ee Eeer gt Enable O Disable Wireless Network List Gran Wireless Network Mame Signal Security MAC Address TP LINK_ 1 BOF 26 WYIPANMYPAZ PSE S4 E6 FC 16 0F 28 TP LINK_ 3G Morne 00 0C 45 76 16 20 TP LINK_EC amp 8623 Mone 00 04 EC EC 68 23 TP LINK_FFFFFF Mone FE FF FF FF FF FF TP LINK_3G_2CBBB4 Ta VWF AMYPAD P Bk OC 82 68 2C BB B4 feng More Ao of 4E F 6E 20 S112AC None O0 01 56 37 12 AC TP LINK_F C62C Mone 0 57 00 F9 C6 2C DASFAF a WPAWPAZ FSF D4 CA 6D 0A 5F 2F TP LINK_MS_EC6612 at WPAIYPAY PSE 5A 9F CC EC BB 12 Wireless Network Name Manually Connect 1 Select Enable to enable your camera s wireless function
13. 6 09 10 45 44 Time Zonge Auto Timezone d C Enable Daylight Saving Time Automatic Time Configuration C Synchronize With NTP Server Set Date And Time Manually C Set Date and Time Manually Save gt Current Time Displays the current date and time of the camera gt Time Zone Select the time zone for the region where the camera is installed from the drop down list Auto Time zone is recommended gt Enable Daylight Saving Time Select this option to enable daylight saving time adjustment If enabled you will see the following screen Wi Enable Daylight Saving Time Automatically e Manually Time Offset 0300 w Stan Time First al sunday w in January we at 0 we 0 W End Time First VI sunday wf in January w at 0 wl 0 Automatically If selected the internal system clocks of the camera will adjust the DST automatically Manually If selected you can adjust the DST by setting the Time Offset Start Time and End Time gt Synchronize With NTP Server Select this option to specify the NTP server name to synchronize the date and time of the camera with those of the time server known as the NTP Network Time Protocol server If enabled you will see the following screen 36 NC200 WEIER EREIET TTT Automatic Time Configuration k Synchronize With NTP Server NTP Service 0 pool_ntp org O poolntp org a Gei NTF Server from Dynamic IF NTP Server You can either enter a domain name o
14. ICES 003 Class B specifications Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada This device complies with RSS 210 of Industry Canada This Class B device meets all the requirements of the Canadian interference causing equipment regulations Cet appareil num rique de la Classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Korea Warning Statements da TAANE SRS ABSA Fo Ys NCC Notice amp BSMI Notice TER WRG RIR E HT E E E EE BTF ARATE AS RI RIN JEKE An ANAE A ey A A ERK In LC solo eet BA AE o P VU 1 Us OR ER EL A a ER ne Ten rr KARA FERR ESR FH Wes de IR A 1 MEAE I eae Fe RR a IR ATE BS Fin 42 52 IIE BT Se PH DA A Be Pee H E 8c HY PE FB a HA FEE VLD FE GU SE RITE SE A o Pad a AER IA EEH Vin R Te WR HS ase A EE AG AS E m YEH YD SS 8 A AS E Ad ORRA ZA RTC EIR RAJEH RBI mn rr ORM cA KKB H mg BRIA mE O fie p O EEH MERE E m RET SEE A RAIA E ng a i HO o SE BRIE IE Fy A JEL ASH aT CAE APA m TRAM AST D I A el AT AIS Em UE REIH Bh SS A EEIT TE 9 MpogykT CepTudikoBaHo 3rigHo c npasnnamn cuctemu YkpCEMNPO Ha BIANOBIGHICTe BNMOTaAM HOpMaTNBHNX HOKyYMeHT B Ta BUMOraM LO nNepeqbayeHi YWHHUMU 3aKOHOAABYUMU akTaMn YkKpalHu DI Safety Information When product has power button the power button is one of the way to shut off the product when there is no power button the only way to comple
15. Si Enable Disable Light Frequency auto hal Time Stamp Enable Disable On Screen Display OSD Enable Disable OSD Text NC200 Save Frame Rate Select the frame rate to use for the video stream from the drop down list Higher settings offer better quality but will require more bandwidth to stream Image Quality Select one of the three levels of image quality from the drop down list High Medium and Low Higher settings offer better quality but will require more bandwidth to stream Backlight Compensation If enabled this feature will compensate for bright backgrounds so foreground objects aren t silhouetted It is enabled by default Light Frequency Select the frequency used by your lighting and power to help reduce image flicker The default setting is auto which is recommended 26 NC200 Boi MEREN Ea gt Time Stamp If enabled the current time of your camera which can be set on System Date Time page will be displayed on the top right corner of the live view screen With this feature enabled you can find out the exact time of the snapshot or record easily gt On Screen Display OSD If enabled you can set the OSD text and the OSD text you entered will be displayed on the top left corner of the live view screen The OSD text is camera name by default If Backlight Compensation Time Stamp and OSD are all enabled see the following two pictures to see the differences Before After Aan fF A Qe y
16. TP LINK User Guide NC200 Cloud Camera 300Mbps Wi Fi REV1 0 1 1910011071 COPYRIGHT amp TRADEMARKS Specifications are subject to change without notice TP LINK is a registered trademark of TP LINK TECHNOLOGIES CO LTD Other brands and product names are trademarks or registered trademarks of their respective holders No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation transformation or adaptation without permission from TP LINK TECHNOLOGIES CO LTD Copyright 2014 TP LINK TECHNOLOGIES CO LTD All rights reserved http www tp link com FCC STATEMENT Fe This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to pro vide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not in stalled and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient
17. The maximum number of users accessing the camera simultaneously The camera can be used outdoors or not The maximum number of users is limited to 13 However it also depends on the total bandwidth accessed to this camera from clients The actual number of connected clients varies by streaming mode settings of resolution frame rate and bandwidth Obviously the performance of the each connected client will slow down when many users are logged on The camera is not weatherproof It needs to be equipped with a weatherproof case for outdoors using However equipped with a weatherproof case might disable the audio function of the camera Install this camera system LED does not light up The camera will be installed and work if a firewall exists on the network The username and password for the first time or after factory default reset Forgot the username and password Forgot the IP address of the camera Internet Explorer does not seem to work well with the camera e Check and confirm that the DC power adaptor included in package is used Secure the power connector and re power it on again e If the problem is not solved the camera might be faulty Contact your dealer for further help If a firewall exists on the network port 80 is open for ordinary data communication The HTTP port needs to be opened on the firewall or NAT router Username is admin and password is admin Note that it s all case sens
18. _FFFFFF None FE FF FF FF FF FF TP LINK_3G_2CBBB4 SH VVPDAIVPDAZHOk OC 82 68 2C BB A4 feng More As o 4E F 6E 20 311240 None O0 01 56 31 12 Ac TP LINK_FOCH2C None 08 57 00 F9 C amp 2C DASE 2 a WWPANYPA PSE D4 C4 6D 04 5F 2F TIRHUINK M ECppi Ta WWPARYPA PSE SA SF CC EC BB 12 Wireless Network Marie TF LINK_1B0F 28 Password C Show password Connect 4 A pop up screen will prompt you for the network modification Click Change to continue The camera s wireless network will change Make sure the camera and computer are in the same LAN or your computer won t be able to access the camera 5 Click OK on the pop up screen to finish wireless connection procedure 15 NC200 Boi MEREN Ea TIPS x The camera is connected to the TP LINK_1BOF26 network To use this wireless connection unplug the camera s Ethernet cable D To start using camera wirelessly unplug its Ethernet cable 3 3 4 Basic Cloud Settings NC200 is a Cloud Camera which can be viewed anytime and anywhere over the Internet with TP LINK Cloud service On this page you can add your camera to an existing TP LINK Cloud account or you can sign up for a TP LINK Cloud account and then add your camera to it LS Note To add a camera to TP LINK Cloud account or to sign up for a TP LINK Cloud account make sure that the camera is connected to the Internet Add Your Camera to TP LINK Cloud Account If you already have a TP LINK Cloud accou
19. a username for your new account 34 NC200 Boi KTERE Ea 3 Enter a password for your new account The password should contain 5 20 characters 4 Enter the password again to confirm it 5 Click Save to save and enable the settings Change Password You can change the password of all the accounts here LS Note The default account and password are both admin Everyone who knows the camera s IP address can access the device with all configuration authority It is necessary to change the default password if the device is intended to be accessed only by administrator To change password follow the steps below 1 Select one user account in the list whose password you want to change 2 Click Change Password and you will see the following screen Account User Mame ser Group admin admin test user Add Change Password ie ete Change Password Current User admin Old Password LLLI New Password eaeeee Confirm Password eneeee SE Vu 3 Enter the current password in the Old Password textbox 4 Enter a new password 5 Enter the new password again to confirm it 6 Click Save to save and enable the settings Delete a User Account 35 NC200 WEIER EREIET TTT You can delete a user account except admin here Select one in the list and click Delete 3 5 2 Date Time On this page you can configure the settings of the internal system clocks for your camera Date Time Time Configuration Current Time 2074 0
20. can specify the module by selecting one from the Module drop down list at the bottom gt Level Displays the severity level of the log information You can specify the level by selecting one from the Level drop down list at the bottom gt Content Displays the details of the log information gt Refresh Click Refresh to refresh the log information gt Save Log Click Save Log and follow the instructions on the browser to save the log as a text file named log txt to your specified location gt Clear Log Click Clear Log to clear all the log information 40 NC200 oillt e E o ta r Lol ooa a Appendix A Specifications Frame Rate amp Resolutions r D N OS o ae Audio Compression PCM Notification Method E mail FTP Bonjour TCP IP DHCP PPPoE ARP ICMP FTP SMTP Standards and Protocols Samba NFS DNS NTP UPnP RTP RTCP HTTP HTTPS 41 NC200 Boi MEREN Ea O S SE Microsoft Internet Explorer 7 or higher Firefox 4 0 or higher Supported Browser Safari 4 0 or higher Chrome 5 0 or higher Opera 12 0 or higher Windows XP Vista 7 8 Mac OS X 10 7 or higher Certification CE FCC RoHS Operating Temperature 0 C 40 C 32 F 104 F Storage Temperature 20 C 60 C 4 F 140 F Environment Operating Humidity 10 90 non condensing Storage Humidity 5 90 non condensing 42 NC200 WEIER ie MN Ea Appendix B Troubleshooting Answer or Resolution
21. d RESET function To use the WPS function press it for 1 second to use the RESET function press and hold for more than 5 seconds NC200 WEIER EREIET TTT Used as RESET button With the camera powered on press and hold the WPS RESET button more than 5 seconds until both the System LED and WPS LED turn off Then release the button and wait the camera to reset to its factory default settings Used as WPS button If your router supports WPS then you can press the WPS RESET button for 1 second to quickly establish a connection between the camera and router 2 4 Mount the Camera 2 4 1 The Screw Size 2 4 2 Mount the Camera LS Note If you use the camera wirelessly mount the camera within the coverage of your wireless network 1 Unscrew the camera head 2 Remove the base cover NC200 Coud Camera 200Mbpe WLE 3 Drill two mounting holes and fix the 4 Put the base cover and camera head back mounting base NC200 WEIER EREIET TTT Chapter 3 Managing the Camera The camera s built in web management page is designed to allow you to easily access and configure your camera Use the management IP address of the camera to log in to the camera You can find the IP address in two ways gt Run the Setup Wizard The IP address is displayed on the Select a camera screen gt Find the IP address on the DHCP setting page of the front device such as router 3 1 Login 1 Open a Web browser and type in
22. eless network e Ethernet port for wired connectivity e UPnP support for network setup amp configuration e 4x digital zoom for close up viewing NC200 Boi KTERE Ea 2 3 Appearance Description 2 3 1 Front Panel Microphone System LED Figure 2 1 Front Panel gt Microphone The camera has a built in internal microphone This microphone is hidden in the pinhole located on the front panel gt System LED Flashing Red The camera starts booting up Solid Red The camera has boot up but is not connected to any network Flashing Green The camera is in firmware upgrade procedure Solid Green The camera is connected to a network or is transferring data NC200 Bo KTERE Ea 2 3 2 Rear Panel Power Jack ETHERNET Port ETHERNET WPS LED WPS RESET Button Figure 2 2 Rear Panel gt WPS LED The camera starts booting up Flashing Green The camera is connecting to a network by WPS function This process will last in the first 2 minutes The camera has boot up The camera failed to be added to a network by WPS function The camera has been successfully added to a network by WPS Solid Green e function This process will last in the first 2 minutes gt ETHERNET Port The ETHERNET port is used to connect the camera to a network via RJ45 cable gt Power Jack The power jack is where you connect the AC adapter to the camera gt WPS RESET Button This button is used for both WPS an
23. etup and management of NC200 Cloud Camera 300Mbps Wi Fi Please read this guide carefully before operation 1 1 Conventions In this Guide the following conventions are used gt The camera or NC200 mentioned in this Guide stands for NC200 Cloud Camera 300Mbps Wi Fi without any explanation gt Bold font indicates a button a toolbar icon menu or menu item Symbol in this Guide a Ignoring this type of note might result in a malfunction or damage to the Note device 1 2 Overview of This Guide Chapter Introduction Chapter 1 About This Guide Introduces the guide structure and conventions Chapter 2 Introduction Introduces the features application and appearance of NC200 Cloud Camera 300Mbps Wi Fi Chapter 3 Managing the Introduces how to quickly set up the camera using the built in web Camera management page Appendix A Specifications Introduces the specifications of NC200 Cloud Camera 300Mbps Wi Fi Appendix B Troubleshooting Lists the answers or resolutions for some common problems NC200 BRA Mert tic Mei TTT Chapter 2 Introduction Thanks for choosing the NC200 Cloud Camera 300Mbps Wi Fi 2 1 Overview NC200 is a versatile solution for home amp office monitoring to Keep an eye on your home kids or workplace whatever it is that you care for most NC200 has a complete system with a built in CPU and web server that transmits high quality video images which can fully meet the need of your small o
24. f the NTP server or select one which will be filled in automatically from the drop down list Set NTP Server from Dynamic IP You can use the NTP server applied in the DHCP server on the network gt Set Date and Time Manually Select this option to set the date and time of the camera manually If enabled you will see the following screen Set Date And Time Manually LA Set Date and Time Manually Year 2014 WM Month 6 eal Day 09 W Hour 10 inal Minute 45 w Second 29 WM Copy Your Computer s Time Settings Copy Your Computer s Time Settings Click this button to copy your Computers current time settings Click Save to save and enable the settings 3 9 3 Management On this page you can reboot the camera backup and restore the camera s current settings reset factory settings and update the camera s software 37 NC200 WEIER EREIET TTT Reboot Reboot your camera Reboot Backup and Restore Back up current settings Backup Restore settings from a backup file Browse Restore Restore factory default settings Reset Update Upgrade from a file on your hard disk Browse Upgrade Software update Your software version is the latest one Reboot Click Reboot and then click Reboot on the pop up screen to confirm Rebooting will not change the camera s setting After rebooting you need to log in to this page again Backup Click Backup and follow the instructions on the browser to save the setti
25. ffice or home s security and surveillance NC200 is an affordable and fully scalable surveillance camera Because the camera can be added to your existing local area network LAN with a stable high speed Wi Fi connection you will potentially save a lot from unnecessary cabling With wireless extender feature it can also be used as a Wi Fi range extender to easily expand your Wi Fi network NC200 can be accessed remotely and controlled from any computer over your local network or through the Internet via a web browser NC200 is a complete and cost effective home or office security solution for it comes with remote monitoring and motion detection feature NC200 is a cloud based Wi Fi video monitoring device with free live streaming and remote viewing which makes it easy to stay connected with what you care most wherever you are You can view and manage your camera from anywhere over the Internet through the TP LINK Cloud website or through the toCamera app for iOS and Android 2 2 Main Features e Monitor your home or office remotely with web based management page e iOS and Android app for remote viewing and management with TP LINK Cloud e TP LINK Cloud www tplinkcloud com access for easy viewing and management e Email or FTP notification triggered by motion detection e Supports wireless 802 11b g n with speed up to 300Mbps e Wireless connectivity compliant with WPS button e Instantly eliminates the dead zones and expand your home s wir
26. i Click Save to save and enable the settings 3 4 8 Advanced Motion Detection Motion detection allows you to specify areas of your camera s video to monitor for motion which can be used to trigger snapshots Refer to 3 4 9 Advanced Notification Sending for more details 27 NC200 WEIER EREIET TTT aaa E TT NEE Motion Detection e Enable O Disable Click the parts of the screen where you would like motion detection to be active Sensitivity Medium w gt Motion Detection To enable or disable the motion detection function here gt Sensitivity Specify the level of difference between two sequential images that would indicate motion Select one of the three levels of sensitivity from the drop down list High Medium and Low Use your mouse to click on the parts of screen where you would like to monitor for motion Click Save to save and enable the settings 3 4 9 Advanced Notification Sending Notification Sending settings are available only after the Motion Detection function is enabled Notification sending function is used to inform you immediately by sending the snapshots which are triggered by the camera s motion detection function to the specified FTP server or E mail address 28 FTP NC200 BRAr KTERE Ea Notification Sending Target FIP IT E mail Save Select FTP you can configure your camera to send snapshots to a specified FTP sever on the following screen
27. in letters digits and _ gt Password Enter a password for your TP LINK Cloud account Password should contain 6 20 characters It can only contain letters digits and _ amp gt Confirm Password Enter the password again to confirm it Click Sign up to sign up for a TP LINK Cloud account After signing up successfully you can add your camera to this account Click Back if you don t want to sign up 3 3 5 Basic LED The camera s LED is on by default If you want to turn it off just select Off LED KEE On Ott Save 3 4 Advanced Click the Advanced menu to display the submenus including Status Network Wireless 17 NC200 WEIER EREIET TTT Connection Wireless Extender Cloud Setting DDNS Video Motion Detection Notification Sending and LED Gi Advanced Status Network Wireless Connection Wireless Extender Cloud Settings DDNS Video Motion Detection Notification Sending LED 3 4 1 Advanced Status Refer to 3 3 1 Basic Status 3 4 2 Advanced Network On this page you can configure your network settings 18 NC200 WEIER EREIT TTT IP Address Dynamic IP Static IP Fallback IF 19 168 0 10 PPPoE PPPoE Enable Disable HTTP HTTP Port an UPnP UPnP Port Forwarding zi Enable Disable UFnFP Name Nc200 Bonjour Bonjour Enable Disable Bonjour Name NWO200 F 62069 Save IP Address On this page you can configure your camera s
28. ion with any other antenna or transmitter CE Mark Warning C 1588 This is a class B product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures Canadian Compliance Statement This device complies with Industry Canada license exempt RSS standard s Operation is subject to the following two conditions 1 This device may not cause interference and 2 This device must accept any interference including interference that may cause undesired operation of the device Cet appareil est conforme aux norms CNR exemptes de licence d Industrie Canada Le fonctionnement est soumis aux deux conditions suivantes 1 cet appareil ne doit pas provoquer d interferences et 2 cet appareil doit accepter toute interference y compris celles susceptibles de provoquer un fonctionnement non souhait de l appareil This device has been designed to operate with the antennas listed below and having a maximum gain of 3 dBi Antennas not included in this list or having a gain greater than 3 dBi are strictly prohibited for use with this device The required antenna impedance is 50 ohms To reduce potential radio interference to other users the antenna type and its gain should be so chosen that the equivalent isotropically radiated power e i r p is not more than that permitted for successful communication Industry Canada Statement Complies with the Canadian
29. itive Follow the steps below 1 Restore the factory default setting by pressing and holding the WPS RESET button more than 5 seconds on the camera 2 Reconfigure the camera e Run the Setup Wizard The IP address is displayed on the Select a camera screen e Find the IP address on the DHCP setting page of the front device such as router Make sure that your Internet Explorer is version 7 0 or later If you are experiencing problems try upgrading to the latest version of Microsoft s Internet Explorer from the Microsoft webpage UPnP NAT Traversal Cannot work with NAT e Maybe NAT router does not support UPnP function Please 43 NC200 Boi KTERE Ea router check user s manual of router and turn on UPnP function Maybe UPnP function of NAT router is not compatible to the IP camera Please contact your dealer to get the approval routers list Maybe too many cameras have been installed on the LAN and Some cameras are then NAT router is out of resource to support more cameras working but others are failed You could turn off and on NAT router to clear out of date information inside router Maybe the IP Address of the camera is already being used by another camera or computer To confirm this possible problem disconnect the camera from the network first and then run the PING utility to check it out May be due to the network cable Try correcting your network cable and configuration Test the network in
30. king after above procedure reset camera to default setting and installed it again If the problem is not solved the camera might be faulty Contact your dealer for further help Cannot access the web Make sure the plugin is installed properly and your browser Image or video does not security settings are set to allow plugins Close and restart the appear in the main page browser Try to browse and log in again When using Windows XP or Vista log on with an appropriate 44 The camera work locally but not externally The unreadable characters are displayed Frame rate is slower than the setting Image Transfer on e mail or FTP does not work The focus on the camera Is bad The color of the image is poor or strange Image flickers NC200 Metal ert ie MN AE account that is authorized to install applications Network congestion may prevent the Image screen from appearing quickly You may choose lower resolution to reduce the required bandwidth Might be caused from the firewall protection Check the Internet firewall with your system or network administrator The firewall may need to have some settings changed in order for the camera to be accessible outside your LAN Make sure that the camera isn t conflicting with any other web server running on your LAN Check the configuration of the router settings allow the camera to be accessed outside your local LAN Check the bandwidth of Internet connection
31. l settings and try again later server connection failed 3 4 10 Advanced LED Refer to 3 3 5 Basic LED 3 5 System Click the System folder to display the sub folders including Account Date Time Management and System Log a System Account DateTime Management System Log 3 5 1 Account On this page you can change the administrator s password and manage the user account s that 33 NC200 WEIER EREIET TTT are allowed to access to your camera Account User Mame User Group admin admin test User Add Change Password Delete gt Username Displays the name of user account gt User Group Displays the group the user account is in Different user group has different limits of authority admin Admin group has all authority of configuration It can only have one account admin user User group can only view the Live View It can have up to five accounts Add a New User Account You can create new user account to provide viewing access for your camera s video User accounts will only be able to access the Live View section of the web configuration page but cannot access any other parts or change any settings To add a new user account follow the steps below 1 Click Add and you will see the following screen Account User Mame User Group admin admin Add Change Password Delete Add a Hew User Account User Mame test Password LLELE confirm Password LELLI SAVE 2 Enter
32. ng data file to your specified location Restore Click Browse to locate the saved backup file and then click Restore The camera will start rebooting and then the settings will be restored to the previous configuration Reset Click Reset and then click Reset on the pop up screen to restore the camera to its factory defaults Don t turn off the camera while resetting After resetting you need to find out the IP address of your camera refer to 3 1 Login and use the default username and password admin admin to log in to this page Update The system will detect whether your camera s current software is the latest one automatically If the software is the latest one you can see a note on the screen Your software version is the latest one If not a screen will pop up for you to download the latest software and you can follow the steps below to upgrade the software 1 Click Download on the pop up screen to download the latest software 38 NC200 WEIER EREIET TTT Mew software version is available please click Download Download Cancel 2 Click Browse to locate the latest downloaded software 3 Click Upgrade to update the camera s software to the latest version 4 Wait for the uploading process to complete and the camera will reboot automatically LS Note 1 We recommend you to use a wired connection for your camera and PC when upgrading firmware 2 The firmware upgrade procedure must not be inte
33. no need of remembering the IP address However if your camera is behind a NAT router you need to set DDNS on your router in no need of setting this on the camera As to xDSL environment most users will use dynamic IP addresses If users want to set up a web or a FIP server then the DDNS Dynamic Domain Name Server is necessary DDNS Service Provider No IP www noip com Ka Go to register Usemame Password Domain Name Connection Status Disconnected Login Save gt Service Provider Select one of the built in DDNS servers from the drop down list No IP 25 NC200 Coud Camera 200Mbpe WLE www noip com DynDNS www dyn com and Comexe www comexe cn LS Note If you have not registered for any of the listed DDNS servers please select one and click Go to register and follow the instructions provided on the official website to register gt gt gt Username Enter the username that is used to log into DDNS Password Enter the password that is used to log into DDNS Domain Name Enter the domain name that is applied to your camera and used to access your camera Connection Status Displays the current status of DDNS connection Click Login After logging in successfully click Save to save and enable the settings 3 4 7 Advanced Video On this page you can configure the video settings for your camera Video Frame Rate 2O0fps i Image Quality High va Backlight Compensation
34. nt to add your camera to your account just enter the TP LINK Cloud account and password and then click Register Cloud Setting Add your camera to Cloud account Dont have an account Please enter your Cloud account and password Account E mail Username Password Camera Mame NC With Cloud service You can view your cloud cameras anytime and anywhere over the Internet Go to W i Tolinke loud cor Fegister gt Account Enter your TP LINK Cloud account either E mail address or username is allowed gt Password Enter your TP LINK Cloud accoun s password gt Camera Name The model such as NC200 is camera name by default You can change it to 16 NC200 WEIER EREIT TTT an easy remember one Camera name can contain up to 30 characters It can only contain digits letters space and 0 After your camera is registered successfully you can go to www tplinkcloud com to view it Sign Up for a TP LINK Cloud Account If you do not have a TP LINK Cloud account click Don t have an account to sign up Cloud Setting E mail Username Password Confirm Password acceptthe TP LINK Cloud Privacy Policy and Terms of Use Back sign up gt E mail Enter a valid E mail address as your TP LINK Cloud account If you forget your TP LINK Cloud password you can reset it via this E mail address gt Username Enter a username as your TP LINK Cloud account Username should contain 1 32 characters It can only conta
35. on set the Sender E mail Port as 465 if STARTTLS is selected set the Port as 25 or 587 gt Sending Interval Set the limit for how frequently E mail notifications will be sent Select one interval from the drop down list For example if you want to use Gmail with TLS for E mail notifications follow the steps below Notification Sending Target FTP Lo E mail Recipient E mail Address test tp link com Add recipient Sender E mail server Port smtp gmail com ABS User Name test gmail com Password eeccee SSL Encryption TLS v Sending Interval 1m d Test SEI 1 Enter the receiver s E mail address in Recipient E mail Address e g test tp link com 2 Enter smtp gmail com in SMTP server 3 Enter your Gmail E mail address in Sender E mail Address e g test gmail com 4 Enter the password required to access the SMTP server 5 Select TLS as the SSL encryption and the SMPT server port number will be changed to 465 automatically D Set the Sending Interval e g 1m 7 Click Save to save and enable the settings Click Test and a test JPEG snapshot will be sent to the recipient E mail address to check whether your settings are correct If the settings are tested correct you will see the following screen Click OK 32 NC200 WEIER EREIET TTT E mail address connecting succeeded for all recipients If the settings are tested incorrect you will see the following screen Click OK Please check your network and E mai
36. our settings are correct If the settings are tested correct you will see the following screen Click OK FTP Servers setting succeeded If the settings are tested incorrect you will see the following screen Click OK Please check your network and FTP settings and try again later 30 NC200 WEIER EREIT TTT FTP service request timed out Please try again later E mail Select E mail you can configure your camera to send snapshots to a specified E mail address on the following screen Notification Sending Target C FIP ka E mail Recipient E mail Address Add recipient SMTP Server Port 7 25 Sender E mail Address Password SSL Encryption Close a Sending Interval im 8 Test Save gt Recipient E mail Address Enter the receiver s E mail address that the notification E mail will be sent to Click Add recipient to add receiver s E mail addresses You can specify up to four recipient E mail addresses gt SMTP Server Port Enter the domain name or IP address and the port of your external E mail server The port is 25 by default gt Sender E mail Address Enter the senders E mal address that is used to send the notification E mail gt Password Enter your password if the SMTP server uses authentication gt SSL Encryption Select TLS or STARTTLS as the SSL encryption select Close to disable SSL encryption 31 NC200 Boi MEREN Ea LS Note If TLS is selected as the SSL Encrypti
37. ress 00 0C 43 76 20 69 IP Address 192 168 1 100 Subnet Mask 255 255 255 0 Default Gateway 192 168 1 1 Primary DNS Server 172 31 1 1 Secondary DNS Server 172 31 1 2 Save gt Static IP Select this option when a static or fixed IP address is obtained for the camera A static IP address will ease your access to the camera in the future Add your camera s static IP information to your router to avoid IP conflicts MAC Address Displays the Ethernet MAC address of the camera The MAC address is read only IP Address Enter a fixed IP address for the camera in dotted decimal notation Subnet Mask Enter the subnet mask in dotted decimal notation The default value is 255 255 255 0 Default Gateway Enter the default gateway in dotted decimal notation Primary DNS Server Enter a DNS address in dotted decimal notation Secondary DNS Server Enter a DNS address in dotted decimal notation 13 NC200 Boi MEREN Ea Click Save to save and enable the settings 3 3 3 Basic Wireless Connection The camera s wireless function is enabled by default This function helps to connect your camera to a wireless network wirelessly If you dont want to use this function just select the Disable option Wireless Connection mi Enable Disable Wireless Network List Wireless Network Mame Security MAC Address TP LINK_ 1 BOF 28 None 54 E6 F C 1B 0F 28 TP LINK_3G None O0 0C 43 7 6 16 20 TP LINK_EC6823 Mone O0 04 EC EC 68
38. rrupted or the camera may be damaged 3 The firmware upgrade procedure is always risky and do not try to upgrade new firmware if it s not necessary 3 9 4 System Log On this page you can review any changes and events happened to your camera The system starts logging automatically after startup System Log Time Module Level Content 2013 01 02 00 27 29 FTP DEBUG msarcv failed No message of desired type continue A 2013 01 02 00 27 28 FIP DEBUG msarcv failed No message of desired type continue 2013 01 02 00 27 28 FTP DEBUG msarcv failed No message of desired type continue 2013 01 02 00 27 28 UserManage DEBUG Get user info admin 2013 01 02 00 27 27 FTP DEBUG msarcv failed No message of desired type continue 2013 01 02 00 27 27 FTP DEBUG msarcv failed No message of desired type continue 2013 01 02 00 27 26 FTP DEBUG msarcv failed No message of desired type continue 2013 01 02 00 27 26 FIP DEBUG msarcv failed No message of desired type continue 2013 01 02 00 27 25 FIP DEBUG msarcv failed No message of desired type continue 2013 01 02 00 27 25 BIE DEBUG msarcv failed No message of desired type continue bd Level Module Refresh Save Log Clear Log 39 NC200 Boi MEREN Ea gt Time Displays the time when the log event occurs The log can get the correct time after you configure on the Date Time page go to Advanced Date Time gt Module Displays the module to which the log information belongs You
39. s 1 3 4 5 and 28 floors 1 4 Central Science and Technology Park Shennan Rd Nanshan Shenzhen China NC200 Bo MEREN AE CONTENTS Chapter 1 About this EE 2 Lil CONVEO EN 2 ke OvemMmewor Eegeregie 2 Chapter 2 Otter EEEEEEEEREEETEEEEEEEEEENER 3 21 e EE 3 Pa FS Fiat EE 3 23 Appearance IC SCHDNO eegene 4 2 3 1 Fee OG st AIS E 4 2 3 2 Ke In TEE 5 2A eeh ge aE EE 6 2 4 1 MGS GI CW 2517 EE 6 2 4 2 MOUNES CAIET EE 6 Chapter 3 Managing the Came ra c cccccsssceeseeeeeeeeeeeeeeeeeeneseneeeesenesenesenesneaenes 8 SNE ee SEH 8 IA EE 9 e GE 11 3 3 1 Ge EEN 11 3 3 2 Basie Edel 13 3 3 3 Basic VWVireless COnneGlON EE 14 3 3 4 Base ele ele e 16 3 3 0 BSE ER HEH 17 Se laten DEE 17 3 4 1 Advanced Status EE 18 3 4 2 AOUN CE ESN EW OE a eect essen ota an aaa 18 3 4 3 Advanced Wireless Connechon ER 3 4 4 Advanced Wireless Evtender 24 345 Advanced Cloud SCMINGS rssi eege 25 340 Advanced DDNS EEN 25 3 4 7 Advanced gt Video BEE 26 3 4 8 Advanced Motion Detection cc ccecceccseceseeeeetseetecenseeeeeteeenseeeeseeenaess 2 3 4 9 Advanced Notification Gendmg 28 eh oL a E EE 33 39 OVSE EE 33 3 5 1 ACCOUN a E E E aaa eanee 33 3 5 2 BERT EE 36 3 5 3 E Ee SINGIN EE 37 Oe SYSICNVLOG eripere et aii ease 39 eeler CN 41 Appendix B Troubleshooting RE 43 NC200 WEIER EREIET TTT Chapter 1 About this Guide This User Guide contains information for s
40. tely shut off power is to disconnect the product or the power adapter from the power source Don t disassemble the product or make repairs yourself You run the risk of electric shock and voiding the limited warranty If you need service please contact us Avoid water and wet locations This product can be used in the following countries UI DON IW IN _ NO TPL TPT po RU SE Ter DS ua us TP LIN K TP LINK TECHNOLOGIES CO LTD DECLARATION OF CONFORMITY For the following equipment Product Description Cloud Camera 300Mbps Wi Fi Model No NC200 Trademark TP LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives Directives 1999 5 EC Directives 2004 108 EC Directives 2006 95 EC Directives 1999 519 EC Directives 2011 65 EU The above product is in conformity with the following standards or other normative documents EN 300 328 V1 8 1 EN 301 489 1 V1 9 2 amp EN 301 489 17 V2 2 1 EN 55022 2010 AC 2011 EN 55024 2010 EN 61000 3 2 2006 A1 2009 A2 2009 EN 61000 3 3 2013 EN 60950 1 2006 A11 2009 A1 2010 A12 2011 EN 62311 2008 The product carries the CE Mark C 1588 Person responsible for making this declaration Yang Hongliang Product Manager of International Business Date of issue 2014 TP LINK TECHNOLOGIES CO LTD Building 24 floor
41. terface by connecting a local computer to the camera via a crossover cable Make sure the Internet connection and setting is ok Make sure the IP address typed in is correct If the camera has a dynamic address it may have changed since you last checked it Network congestion may prevent the web page appearing quickly Wait for a while The IP address and Subnet Mask of the PC and camera must be in the same class of the private IP address on the LAN Make sure the http port used by the camera default 80 is management page and pret forward to the camera s private IP address other web pages of the l l l camera from Internet The port number assigned in your camera might not be Explorer available via Internet Check your ISP for available port The proxy server may prevent you from connecting directly to the camera set up not to use the proxy server Confirm that Default Gateway address is correct The router needs Port Forwarding feature Refer to your router s manual for details Packet Filtering of the router may prohibit access from an external network Refer to your router s manual for details Access the camera from the Internet with the global IP address of the router and port number of camera Some routers reject the global IP address to access the camera on the same LAN Access with the private IP address and correct port number of camera When you use DDNS you need to set Default Gateway and DNS server address If its not wor
42. to horizontally flip the current image 10 NC200 WEIER EREIT TTT Drag the slider to adjust the size of the current The maximum zoom ratio is 4 times Mute off You can hear the current sound by the Click CE and it will become KR camera Mute on The current sound by the camera is Click CB and it will become EE turned off Drag the slider to adjust You can adjust the sound volume only with mute the sound volume off ED Click to enlarge the 3 Press ESC key to return to the original screen current image to full display screen display ES gt Brightness Drag the Brighiness slider to adjust the brightness level of camera Large value will brighten the current displayed screen gt Contrast Drag the ontrast slider to adjust the contrast level of the camera Large value will contrast the current displayed screen heavily gt Saturation Drag the Saturation slider to adjust the saturation level of the camera Large value will saturate the current displayed screen to be more colorful gt Resolution Select the desired video resolution between two formats 640 480 and 320 240 Higher setting offers better quality but will require more bandwidth to stream gt Preset Click the Preset button to restore to factory image settings 3 3 Basic Click the Basic menu to display the submenus including Status Network Wireless Connection Cloud Settings and LED Basic Status
43. unction just select the Enable option Wireless Extender e Enable Disable Host Wireless Network Name TP LINK_1BOF26 Extended Wireless Network Name ei Same as Host Max Clients Unlimited Save gt Host Wireless Network Name Displays the name of the wireless network which your camera is connected to It is read only gt Extended Wireless Network Name Name of the wireless network that your camera will extend Same as Host The extended network will use the same name and settings as your Host network Your devices can use the same wireless information to connect to both the host and extended networks Create a New One Select this to manually set the name and security used for the extended network You devices can use the wireless parameters you set to connect to the extended network 24 NC200 Boi KTERE Ea Wireless Extender Enable Disable Host Wireless Network Name TP LINK_1BOF2S Extended Wireless Network Name Same as Host Security Max Clients Unlimited Save gt Max Clients Set the maximum number of clients that are allowed to connect to the extended network Click Save to save and enable the settings 3 4 5 Advanced Cloud Settings Refer to 3 3 4 Basic Cloud Settings 3 4 6 Advanced DDNS lf your camera is connected to xDSL modem or cable modem directly you might need this feature on the camera to allow you and your friends have access to the camera using domain name in
44. xample when HTTP port number is set to 2000 and the IP address of your camera is set to 192 168 1 100 you should type in http 192 168 1 100 2000 instead of http 192 168 1 100 to access the camera HTTP HTTP Port BI gt HTTP Port The default value is 80 If you want to use a port number other than 80 enter a port number between 1 and 65535 UPnP Universal Plug and Play This camera is an UPnP enabled one This means the camera can dynamically join a network obtain an IP address In turn the camera can leave a network smoothly and automatically when it is no longer in use UPnP is enabled by default if you don t want to use this function just select the Disable option UPnP UPnP Port Forwarding si Enable Disable UPnP Name NC 200 gt UPnP Port Forwarding To enable or disable the UPnP Port Forwarding service here If this function is enabled and your router supports UPnP the cameras and router can communicate with each other so that the router knows which ports are used by which camera gt UPnP Name Displays the camera name 21 NC200 WEIER EREIT TTT Bonjour Bonjour also known as zero configuration networking enables automatic discovery of computers devices and services on IP networks Bonjour uses industry standard IP protocols to allow devices to automatically discover each other without the need to enter IP addresses or configure DNS servers Bonjour Bonjour Enable Disable Bonjour Name NC2
Download Pdf Manuals
Related Search