Home

Ergotron StyleView

image

Contents

1. and permanent and dry erase markers can be removed with 91 isopropyl alcohol and a soft cloth lodine stains can be removed with commonly used cleaners and a soft cloth e Never use steel wool or other abrasive materials that will damage the surface finish e Do not use strong solvents such as trichloroethylene and acetone These solvents will damage the surface finish It is recommended that any cleaning solution be tested on a small inconspicuous area to ensure surface is not harmed A sajustment Service Replacement DO NOT attempt to adjust service or replace any part of the StyleView Cart unless directed to do so through Ergotron approved documentation i e installation instructions Only Ergotron Inc or an Ergotron certified entity may adjust service or replace StyleView Cart components If any component on the Cart is missing or damaged the Cart must not be used contact Ergotron Customer Care immediately to request a replacement part Cables Keep cables neatly organized on the Cart a variety of solutions are provided with your cart for this purpose Excess cables should be routed away from moving components with cable clips Review Cable Routing section of this guide or contact Ergotron Customer Care for more information Casters Check casters periodically to make sure they are clean and free of debris that would prevent smooth travel Avoid moving Cart across uneven dirty or damaged surfaces A customer Equipment Make
2. and stay where you set it If movement is difficult or the product does not stay where you set it follow the adjustment instructions to loosen or tighten the tension to create a smooth easy motion Depending on your product and the adjustment it may take many turns to notice a difference 514mm 9 16 gt IMPACT HAZARD MOVING PARTS CAN CRUSH AND CUT Failure to heed this warning may result in serious personal injury or property damage Minimize Lift Tension BEFORE Removing Mounted Equipment Shipping Cart Storing Cart DANGER D IMPACT LES PARTIES EN MOUVEMENT PEUVENT CRASER ET COUPER Il existe un risque de blessure corporelle ou d endommagement mat riel en cas de non respect de cet avertissement Minimisez la tension d l vation AVANT de retirer l quipement fix d exp dier le chariot de stocker le chariot www ergotron com 826 501 This Class A digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe A est conforme a la norme NMB 003 du Canada FCC Compliance Statement The cart has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and 1 Worksurface used in accordance
3. sure equipment is balanced and mounted securely to Cart Do not reposition Cart components on riser or tower unless instructed to do so in the installation instructions Moving Cart components too high or too low on the Riser may create an unstable condition leading to equipment damage or even personal injury Contact Ergotron Customer Care for information about moving Cart components Safety Alerts Associated with this Product The following Warnings Cautions appear in this reference guide or on the cart NOTE Failure to adhere to these guidelines may result in equipment damage or personal injury AS caution The lift brake helps stablilize the worksurface and keyboard tray during normal use but it DOES NOT increase load capacity DO NOT load riser with equipment totaling more than the maximum weight capacity specified by Ergotron Ensure optimum lift function by testing and if necessary re adjusting tension whenever the weight mounted to the riser changes i e equipment is removed or added See Set Riser Lift Tension adjustment instructions AX caution Do not operate StyleView Cart with missing or damaged components Do not remove modify or substitute Cart components without consulting Ergotron If you encounter problems with Cart installation or operation contact Ergotron Customer Care A caution DO NOT overtighten fasteners Overtightening may cause damage to your equipment N warne Stored Energy Hazard The worksurface lift mechanism
4. 7 SS LE USB Type A Re udi NOTE Bar Code Scanner should be connected directly to AN computer USB port DO NOT connect Bar Code Scanner to the USB Hub 888 24 297 G 00 rev A 08 14 7 15 Set up Set up laptop boosters so the screen fits through the slot in the worksurface and the bottom of the screen is visible when the worksurface is attached 822 470 00 8 15 888 24 297 G 00 rev A 08 14 Set up b Plug the following factory connected cables into your computer USB This cable runs from the USB Hub to your computer and uses your computer to power the USB Hub and Keyboard Lights NOTE Your computer must be turned on for the USB Hub and Keyboard Lights to function 888 24 297 G 00 rev A 08 14 9 15 8 DO NOT OBSTRUCT AIR VENTS Obstructing air vents may cause overheating and result in equipment BR 10 15 888 24 297 G 00 rev A 08 14 It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps Any time equipment is added or removed from this product resulting in a change in the weight of the mounted load you should repeat these AED adjustment steps to ensure safe and optimum operation SEE MANUAL 822 421 00 Adjustments should move smoothly and easily through the full range of motion and stay where you set it If adjustments are difficult and do not
5. User Guide ERGOTRON StyleView SV43 Cart with Laptop Mount Tools Needed b E iy PR i N 14mm 9 16 LLN Components p a m 8mm UJ 2x CD M3 5 x 6mm x a 11 Auto Lock Drawer os 00000000000000000000000000000000000000000 12 13 M4x12mm E MICA O 13 Maintenance amp Safety 14 15 For service and warranty visit www ergotron com For local customer care phone numbers visit http contact ergotron com For the latest User Installation Guide and StyleLink Software Download please visit www ergotron com User s Guide English Gu a del usuario Espa ol Manuel de l utilisateur Francais Gebruikersgids Deutsch Benutzerhandbuch Nederlands Guida per l utente Italiano www ergotron com Anvandarhandbok svenska USA 1 800 888 8458 000 N Europe 31 0 33 45 45 600 n China 86 769 86018920 888 24 297 G 00 rev A 08 14 1 15 Features amp Specifications IMPORTANT This product will need tension adjustments once installation is complete Make sure all equipment is properly installed on the product before attempting range of motion or tension adjustments Any time equipment is added or changed on this product resulting in a different mounted weight you should repeat the adjustment steps to ensure safe and optimum operation This product should move smoothly and easily through the full range of motion
6. acy PIN allows all drawers to unlock at the 1 Enter Master PIN and press ENTER for Mode Menu same time Drawers should then be opened at least slightly as the system will auto lock after 2 Press 2 for Pharmacy PIN Entry Mode 10 seconds All LEDs will flash green until system auto locks Once a drawer is opened the 3 Input Pharmacy PIN and press ENTER all LEDs blink green in PIN is accepted corresponding LED for that row will light solid until it is placed back into its original location 4 Pharmacy PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice 12 15 888 24 297 G 00 rev A 08 14 Auto Lock Drawer Unlock Drawer 2 methods NOTE All Drawers in row must be closed before a new row can be unlocked Enter User PIN only numbers for available drawer rows flash green then press desired drawer row number e Key turn clockwise 1 4 turn Drawer Row Numbers Lock Drawer e Wait 4 seconds for lock to engage automatically NOTE Always ensure drawer is pushed in all the way and engaged with lock Drawer Troubleshooting No LEDs on keypad when pressing any number Verify battery box is connected to controller e Verify keypad cable is connected to controller e Verify battery box switch is in the ON position and that batteries are properly installed Drawer selection not available when User PIN is entered e Check to make sure drawer cable is installed securely e Remove power from drawer syste
7. ejected exit current mode after 5 seconds timeout All LEDs blink green 3 times PIN entry accepted All LEDs flashing red Firmware update in progress All LEDs flashing red green System power ON or low battery condition Moving stow before you go 1 During normal movement release brake and lower worksurface to lowest position for optimal stability and unobstructed view 2 Tuck away open trays and return mouse scanner and other accessories to their places 3 Unlock both front casters 4 Push cart from rear with elbows bent at about 90 to maximize control and minimize muscle strain 5 Don t run out Before moving make sure cord is unplugged from outlet and hooked to basket for safe travel Remember charge battery fully 10096 every day 13 15 Maintenance 8 Safety Hazard Symbols Review The Meaning of Symbols appearing in this Guide on the Symbol Cart or on the Power System These symbols alert you to a safety condition that demands your attention You should be able to recognize and understand the significance of the following Safety Hazards if you encounter them on the Cart or within Cart documentation such as this Set up Guide Signal Word Level of Hazard Color Indicates an imminently hazardous situation which if not avoided will result in death or serious injury Indicates a potentially hazardous situation which if not avoided could result in death or serious injury Indicates a potentially
8. g non medical equipment supplied as part of a system directly to the wall outlet when non medical equipment is intended to be supplied by the multiple socket outlet Risk of shock or personal injury when connecting any equipment that has not been supplied as part of the medical system to the multiple socket outlet Recommended Periodic Inspection and Maintenance UI Ethernet USB Inspect for wear pinching bad cables connectors Inspect for wear and debris Monthly Inspect to ensure that maximum recommended loads are not exceeded Maximum Load 1 Please dispose of all batteries in accordance with local law 2 Always replace with similar size battery 33 A h to replace 33 A h and always replace in pairs ERGOTRON 2014 Ergotron Inc All rights reserved While Ergotron Inc makes every effort to provide accurate and complete information on the installation and use of its products it will not be held liable for any editorial errors or omissions including those made in the process of translation from English to another language or for incidental special or consequential damages of any nature resulting from furnishing this instruction and performance of equipment in connection with this instruction Ergotron Inc reserves the right to make changes in the product design and or product documentation without notification to its users For the most current product information or to know if this document is available in language
9. hazardous situation which if not avoided may result in minor or moderate injury Used without the safety alert symbol indicates a potentially CAUTION hazardous situation which if not avoided may result in property damage INSTRUCTIONS Follow operating instructions 1 Please dispose of all batteries in accordance with local EQUIPMENT amp ACCESSORIES DISPOSAL law 2 All Electronics should be recycled through an lil INSTRUCTIONS Follow operating instructions 3 Remaining plastics and metals can be recycled through electronics recycler a commercial recycler can and Maintenance The following procedures are not guaranteed to control infection The hospital infection control administrator or epidemiologist should be consulted regarding cleaning procedures and processes To avoid risk of electric shock do not expose electrical components to water cleaning solutions or other potentially corrosive liquids or substances Do not immerse Cart or Cart components in liquid or allow liquids to flow into the Cart Wipe all cleaners off surface immediately using a damp cloth Thoroughly dry surface after cleaning Do not use flammable cleaners on Cart surfaces due to close proximity of electrical power and equipment All paints and plastic Cart components will withstand cleaning by most commonly used diluted non abrasive solutions such as quaternary ammonia compounds ammonia enzyme cleaners bleach or alcohol solutions Pen
10. is under tension and will move up rapidly on its own as soon as attached equipment is removed For this reason DO NOT remove equipment unless the worksurface has been moved to the highest position on the tower Failure to follow this instruction may result in serious personal injury and or equipment damage When Shipping the cart set the worksurface lift mechanism to the lowest tension setting CAUTION DO NOT loosen tighten or remove any other nuts or bolts on the riser or top of tower Tampering with nuts or bolts may result in an unstable Cart leading to equipment damage and or personal injury CAUTION Release Lift Brake before moving work surface Moving work surface while Lift Brake is engaged may cause serious damage to Lift Engine warne In the event that repair of the StyleView Cart is needed contact Ergotron Customer Care immediately Cart repair can only be performed by Ergotron Inc or by an Ergotron authorized agent WARNING This cart is not intended for use in a flammable anesthetic mixture or oxygen rich environment 14 15 888 24 297 G 00 rev A 08 14 Maintenance amp Safety Configuration 8 Safety AM additional multiple socket outlet or extension cord shall not be connected to the medical system A When used in a Medical Electrical system connect only equipment that complies with IEC ISO UL ANSI or CSA standards that are relevant to that equipment A Risk of shock or personal injury when connectin
11. ll store up to 100 PINs on the cart Ergotron recommends the following for choosing PIN digit length assumes less than 1 in 25 chance of guessing random User PIN Max number of User PINs gt 50 5 digit length recommended Max number of User PINs gt 300 6 digit length recommended For maximum security use PIN length of 7 Set up Master PIN for the First Time Default Master PIN 12345 Contact Ergotron Customer Care for instructions if Master PIN is lost 1 Enter default Master PIN 1 2 3 4 5 then press ENTER 2 Press 5 for Master PIN Entry mode 3 Enter new Master PIN and press Enter LEDs will blink green if PIN is accepted 4 Master PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice Master PIN Mode Menu Enter Master PIN and then select one of the below numbers to enter that mode 1 User PIN Entry Mode 2 Pharmacy PIN Entry Change Mode 5 Master Pin Change Mode Programming User PINS 1 Enter Master PIN and press ENTER for Mode Menu 2 Press 1 for User PIN Entry Mode 3 Input new User PIN and press ENTER All LEDs blink green if PIN is accepted You may enter multiple USER PINs consecutively 4 User PIN entry mode will exit after 5 seconds of inactivity LEDs blink red twice NOTE User PIN cannot be the same as a Master PIN or Pharmacy PIN Once maximum User PIN storage is exceeded the oldest User PIN will be over written Programming Pharmacy PIN Note System will hold 1 Pharmacy PIN Pharm
12. m for 10 seconds and re apply LEDs flash red green after User PIN in entered Battery charge is low check to make sure USB charging cable is plugged into computer and computer is ON Set up 1 4 Keyboard Light Keyboard Light will automatically turn off after 15 minutes if not manually turned off Ergonomics Working customize to your size 1 Set top of monitor screen about one inch below eye level Release brake and lift or lower riser as needed 2 Tilt screen for comfortable viewing and to reduce eye and neck strain 3 Pull keyboard tray forward and position mouse tray on right or left as needed 4 Work with elbows bent at about 90 to minimize muscle strain 5 If the riser moves up and down with difficulty or if it drifts out of set position consult the product manual for adjustment information 6 Stay in charge Powered carts should be plugged into outlet as often as possible to keep battery charged and computer running 888 24 297 G 00 rev A 08 14 LEDs Alarm Meaning 1 2 3 4 or 5 LED ON green Corresponding Drawer is open 1 2 3 4 or 5 LED flashing red and alarm sounding Corresponding Drawer is open longer than 20 seconds Mute alarm by pressing flashing button corresponding to open drawer All available drawer numbers flashing green Waiting for drawer selection see Unlock Drawer All LEDs flashing green Pharmacy mode all drawers are unlocked All LEDs blink red twice PIN entry r
13. r 1 Drawer rawers 1 0 5 Es gt 267 mm S gt 267 mm 315 mm Weight Capacity 20 508 mm 2 Ibs 0 9 kg see inset below Total weight capacity per drawer 2 lbs 1 kg 0 25 Ibs 0 1 kg Total weight capacity per drawer 888 24 297 G 00 rev A 08 14 3 15 Dimensions 19 5 2 495 mm 50 5 EDS 1282 mm 31 51 T Lm 3 27 787 1295 mm 83 mm mee ame 13 4 xd 3 4 2 7 4 AE gt 40 216 mm a 50 mm 390 mm an 1016 mm 000 Lh 19 6 499 mm 30 75 445 mm 23 43 781 mm 584 1092 mm JF z 16 75 OL 425 mm 19 25 2 51 mm 4 aos 3 12 4 mm 315 mm 21 102 mm 22 533 mm 562 mm Laptop Compartment When figuring dimensions include mounted accessories protruding cables and port replicators or docking stations 466 mm 4 15 888 24 297 G 00 rev A 08 14 Release Brake to move riser CAUTION Completely release brake engagement before raising or lowering the cart Raising or lowering the cart with the brake partially engaged may cause F product damage gt gt 6 alg 2x 4 M M3 5 x 6mm 888 24 297 G 00 rev A 08 14 5 15 Set up 888 24 297 G 00 rev A 08 14 6 15 Alcohol Prep b Connect Keyboard and Mouse to USB Hub SS GEE P lt SIS NS SSS SSS SSS LL RSS
14. s other than those herein please contact Ergotron No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written consent of Ergotron Inc 1181 Trapp Road Eagan Minnesota 55121 USA Patents Pending and Patented U S 8 Foreign Ergotron is a registered trademark of Ergotron Inc 888 24 297 G 00 rev A 08 14 Americas Sales and Gorporate Headquarters 1181 Trapp Rd St Paul MN USA 800 888 8458 1 651 681 7600 www ergotron com salesQergotron com APAC Sales Tokyo Japan www ergotron com EMEA Sales Amersfoort The Netherlands 31 33 45 45 600 www ergotron com info euQergotron com Worldwide OEM Sales www ergotron com info oemQergotron com apaccustomerservice ergotron com 15 15
15. stay in the desired position follow the instructions to loosen or tighten the tension to create a smooth easy adjustment motion Depending on your product and the adjustment it may take several turns to notice a difference Adjustment 4 J CUSTOMER le Lift Up and down Release Brake to move riser O Follow these instructions to tighten or loosen tension 2 may require 40 0 7 AUE SSH x revolutions M4 x 8mm K2 gt e NOTE Adjustment Y Ww Tx JI RS 3 888 24 297 G 00 rev A 08 14 11 15 Auto Lock Drawer CAUTION Only use NiMh rechargeable batteries Using non 1 3 AutoLock Drawer Battery Pack 6x rechargeable batteries may cause product damage AA Rechargeable Nickel Metal Hydride USB to computer USB to charge ALD Batteries may not come fully charged and may need to charge for several hours To charge ALD batteries batteries computer needs to be powered on and connected to the USB hub CAUTION Open only one drawer at a time Do Not push cart when drawers are open Failure to follow these instructions may cause the cart to be unstable NOTE User should change Master Personal Identification Number PIN upon receipt of cart Lost Master PIN Contact Ergotron Customer Care for instructions All PINs may vary in length from 4 7 digits Number of PINs possible Carts using StyleLink will store up to 1 000 PINs on the cart Carts not using StyleLink wi
16. with the instruction manual may 2 Secure storage for open laptop cause harmful interference to radio communications 3 Front Handle Operation of this equipment in a residential area is 4 Height Adjustment Brake Handle likely to cause harmful interference in which case the 5 USBHub connects keyboard and mouse USB cables user will be required to correct the interference at his 6 Keyboard tray slides out tilts and allows for right or left mousing with attached mouse holder own expense 7 Keyboard Light under Front Handle Changes or modifications not expressly approved 8 Keyboard Light Switch by Ergotron Inc could void the user s authority to 9 Cable Management and Storage for excess cables and power supplies operate the equipment 10 Storage Basket and Rear Handle Please contact Ergotron for complete EMC compatibility 11 Front Locking Casters information 12 Laptop Screen Holders 13 Quick Reference Card 14 Scanner Holder Teri6eratire Rande mem 15 Antimicrobial worksurface and antimicrobial coating on wrist rest 16 Auto Lock Drawer see page 3 for drawer configurations Relative Relative Humidity Humidity Range VC Range VC Operational Storage Product was placed on the market after 13 August 2005 2 15 888 24 297 G 00 rev A 08 14 Features amp Specifications Part Number Auto Lock Drawer 4 Drawers 28 compartments 6 Drawers 24 compartments SV43 1190 0 9 Drawers 36 compartments Auto Lock Drawe

Download Pdf Manuals

image

Related Search

Related Contents

Asrock Z77 Pro4-M  Xerox Phaser 6280 User's Manual  COMPASS  Land Rover TestBook User Manual - Eng  取扱説明書 施工説明書  キャビトロン プラスMP タップオン  Microsoft Word - PARTE 1 CAPITULO 12  BMW 320i Sedan Service and Warranty Information  X-Stream VISION User Manual  Comment continuer de chanter l`Amérique  

Copyright © All rights reserved.
Failed to retrieve file