EK Water Blocks 3831109821268
Contents
1. pads EKWB web shop Thermal PAD A 1mm 100x16mm EAN 3830046996626 Thermal PAD A 0 5mm 100x16mm EAN 3830046996619 5 PLACING THERMAL PADS ON MOTHERBOARD Place thermal pads you cut on PCB as shown on picture bellow PLEASE REMOVE THE PROTECTIVE FOIL FROM BOTH SIDES OF THE THERMAL PADS PRIOR TO INSTALLATION EK recommends using small drops of electrically non conductive for example Arctic Cooling MX 2 or MX 4 thermal grease on each phase regulator that is being covered with thermal pad see picture below in order to even further improve the thermal performance of the EK FB KIT ASUS R5E series water block Place 0 5mm thermal pads in larger strips over marked area and make sure all mosfet chips are covered Place 1mm thermal pads in larger strips over the coils inductors This is merely to prevent any possible short circuiting Due to the uneven nature of motherboard manufacturing not all of a i A a a aH a the inductors will have contact with the thermal amp E co pad This is normal Dm a All disclosures notices and warranty conditions are being written on EKWB web page Please check terms of use Published on October 27 2014 1 PLACING SB BLOCK ON MOTHERBOARD Place the SB part of the water block with 2 PLACING MOSFET BLOCK ON MOTHERBOARD Place the water block preinstalled 2 5mm standoffs kit gently to the motherboard or vice versa Make sure that gently to2. cessfully complete installation of the FB KIT ASUS R5E and cannot be used in combination with the FB KIT ASUS RSE X99 PCH SB STEP 2 PREPARING YOUR MOTHERBOARD 1 REMOVING STOCK COOLER Remove all encircled screws There are 13 screws on the 2 CLEANING THE PCB Carefully detach the original stock cooler after back of the motherboard that needs to be removed in order to remove the factory installed removing all screws securing it to the board Wipe off the remains by using SB MOSFET heat pipe cooling solution non abrasive cloth or gtip as shown on sample photo of the original thermal Nee oo ibd compound until the components and circuit board are completely clean is Eee lt Shige miat EKWB recommends the use of denatured alcohol for removing TIM leftovers ezi ar pany e G 3 APPLYING THERMAL COMPOUND Apply thermal compound lightly coat the Jnte X99 PCH 4 CUTTING THERMAL PADS Your block comes with thermal pads which SB with electrically_non conductive thermal grease for example Gelid GC Extreme Arctic needs to be trimmed in order to fit the voltage regulation area Cooling MX 2 or MX 4 EKWB recommends to apply thermal grease in cross form for best VRM MOSFET on the motherboard s circuit board WARNING DIMENSIONS ON PICTURES BELOW ARE SCALED VS OA A jj 1 Thermal pad A 0 5mm 100 Af for VRM MOSFET 2 Thermal pad A 1 0mm 100 for inductor coils 16 Replacement thermal
3. ekwD Installation and mounting manual for EK FB KIT ASUS R5E water block This product is intended for installation only by expert users Please consult with a qualified technician for installation Improper installation may result in damage to your equipment EK Water Blocks assumes no liability whatsoever expressed or implied for the use of these products nor their installation The following instructions are subject to change without notice Please visit our web site at www ekwb com for updates Before installation of this product please read important notice disclosure and warranty conditions printed on the back of the box Before you start using this product please follow these basic guidelines 1 Please carefully read the manual before through before beginning with the installation process 2 Please remove your motherboard from the computer to assure safest mounting process in order to prevent any possible damages to your CPU and or motherboard s circuit board PCB 3 The EK High Flow and EK CSQ type fittings require only a small amount of force to screw them firmly in place since the liquid seal is ensured by the rubber O ring gaskets 4 The use of quality market proved corrosion inhibiting coolants is always strongly recommended for any liquid cooling system STEP 1 GENERAL INFORMATION Sample photo of ASUS Rampage V Extreme edition motherboard Mosfets IMPORTANT NOTICE CPU socket ROG LED Logo has to be removed in order to suc
4. g circuit EKWB recommends using EK CSQ compression fittings with the EK FB KIT ASUS R5E series water block You can use any opening as an inlet outlet port Plan your tubing routing in advance e EK CSQ fitting REQUIRED TOOLS scissors philips screwdriver thermal grease 2mm Allen key All disclosures notices and warranty conditions are being written on EKWB web page Please check terms of use Published on October 27 2014
5. the motherboard or vice versa Make sure that mounting holes are mounting holes are aligned Skip to STEP 4 on how to fasten the water block to the aligned motherboard using the enclosed screws and washers ya z MOSFET block SB block l m aog You can use a bit of themal paste to glue the PVC washers on the standoffs for easier installation of the waterblock Prior to fastening the screws please make sure the mounting holes on the motherboard s circuit Temporarily remove the water block to check for uniform surface contact board are aligned with the water block between the block and the components Then repeat steps 3 and 4 to reattach the block applying more or less pressure to the areas where you have found it necessary Note that there is no need for perfect thermal pad imprint on the inductors coils mentioned in STEP2 A SB block Use five M3x5 DIN7985 and washers Tighten the screws beginning near the south bridge and continue evenly outwards Do not use excessive force when tightening the screws B MOSFET block Use ASUS factory stock backplate and two M3x8 DIN7991 screws Use 2mm allen key to tighten the screws Do not use excessive force when tightening the screws Use the enclosed screws and washers as shown in picture below M3x8 DIN 7991 screw T ASUS Factory backplate a M3x5 DIN 7985 screw PVC washer i Attach the liquid cooling tubes and connect the water block s into the coolin
Download Pdf Manuals
Related Search