Home

UTAX P-C3060DN

image

Contents

1. 5 Click Print 6 Forsettings that are configurable refer to Embedded Web Server RX User Guide Printing Operation 2 13 gt Notice this license agreement View License Agreement By using or installing the device drivers and software included in this package you agree to become bound by the terms and conditions of C d Read manuali and readme mes Remove devices river and Installing the Printer Driver Ensure the printer is plugged in and connected to the PC before installing the printer driver from the DVD ROM Note Installation on Windows must be done by a user logged amp on with administrator privileges When connected by USB cable Plug and Play is disabled on this device when in Sleep mode To continue the installation press the GO key to wake the device from Low Power Mode or Sleep before continuing KX XPS DRIVER cannot be installed on Windows XP Installing Printer Driver in Windows Express Install The following procedure is an example for installing the software in Windows 7 using Express Install For details refer to Custom Installation in the Custom Install on page 2 16 1 Insert the DVD ROM Note Installation on Windows must be done by a user logged on with administrator privileges If the Welcome to the Found New Hardware Wizard dialog box displays select Cancel If the autorun screen i
2. 8 10 e Ff Da 3 9 8 Left Cover 9 Waste Toner Box 10 Main Charger Units on the Drum Units 11 Magenta Toner Container M 12 Cyan Toner Container C 13 Yellow Toner Container Y 14 Black Toner Container K Machine Parts Machine Parts 17 Internal Components 15 16 17 18 Components at the Rear of the Printer 20 21 22 Paper Transfer Unit Paper Ramp Duplex Unit Envelope Switch De 2 ur 19 20 21 22 23 24 25 23 USB Memory Slot Power Cord Connector Option Interface Slot Network Indicators Network Interface Connector USB Interface Connector Rear Cover 19 1 3 1 4 Operation Panel 26 27 28 30 31 33 34 O Eee Ready w O MENU E Data eB i Attention me Ce 26 27 28 29 30 31 32 33 34 29 32 Message Display Ready Indicator Data Indicator Attention Indicator Arrow Keys MENU Key OK Key GO Key Cancel Key Machine Parts Printing Operation 2 Printing Operation This chapter contains explanations on the following topics Changing Network Interface Parameters 2 2 Printing a Network Interface Status Page 2 4 Embedded Web Server RX 2 5 Installing the Printer Driver 2 14 Printing from Application Software 2 21 Printing by AirPrint 2 22 Status Monitor 2 23 Energy Saver Fu
3. Printing Operation Printing Operation Setting Description E mail Send Settings E mail Size Limit Enter the maximum size of E mail that can be sent in kilobytes When E mail size is greater than this value an error message appears and E mail sending is cancelled Use this setting if you have set E mail Size Limit for SMTP server If not enter a value of 0 zero to enable E mail sending regardless of the size limit Sender Address Enter the E mail address of the person responsible for the machine such as the machine administrator so that a reply or non delivery report will go to a person rather than to the machine The sender address must be entered correctly for SMTP authentication The maximum length of the sender address is 128 characters Signature Enter the signature The signature is free form text that will appear at the end of the E mail body It is often used for further identification of the machine The maximum length of the signature is 512 characters Function Default Change the function default settings in Common Job Defaults Settings page 4 Click Submit Registering a Custom Box You can register a custom box from Embedded Web Server RX 1 Access Embedded Web Server RX by referring to Accessing 2 Device Information gt Ego Status gt Job Box Settings Device Settings gt DA Function Settings gt 5 Embedded Web Server RX on page 2
4. Share this printer on the network Sharing Preferences Default printer Last Printer Used B Default paper size A4 B d HD cick the tock to prevent further changes Protocol Line Printer Daemon LPD Address 192 168 48 21 Valid and address Queue BD Leave blank for default queue Print Using More Printers Add Installable Options Make sure your printer s options are accurately shown here so you can take full advantage of them For information on your printer and its optional hardware check the documentation that came with it Paper Feeders Not Installed 1 Optional Disk RAM Disk Cancel Continue 800 ele ED Hope Pint Queses Open Print Queue Options amp Supplies idie C Share this printer on the network Sharing Preferences le Default printer Last Printer Used Z Default paper size A4 Z n U cick te tock to prevent further changes 2 20 8 Click the plus symbol to add the installed printer driver 9 Click the IP icon for an IP connection and then enter the IP address and printer name The number entered in Address will automatically appear in Name Change if needed 2 Note When using a Bonjour connection select Default and y click the item that appears in Printer Name The driver with the same name as the machine automatically appears in Driver 10 Select the options available for the machine
5. A new toner kit for each color contains the following items Toner Container Plastic waste bags for old toner container and old waste toner box Maintenance Maintenance Waste Toner Box e Installation Guide Note Do not remove the toner container from the carton until you are ready to install it in the printer Understanding Messages Requesting Toner Container Replacement The printer displays messages for individual colors at two stages of toner usage This message is automatically alternated with the other printer message such as Ready e When the printer becomes low on toner for example in the cyan container the printer displays the message Toner low C as the first caution Note the replacement is not always necessary at this stage If you ignore the above message and continue printing the printer displays the message Replace toner just before the toner is used up The toner container must be replaced immediately Clean the separate charger wires etc After the cleaning is finished however the message does not automatically change to Ready To restart printing you must press GO and make the printer ready In either case replace the toner container refer to Toner Container Replacement on page 3 2 3 4 Top Cover Top Tray Replacing the Toner Container This section explains how to replace the toner containers When replacing the tone
6. click the arrow button to move it to the Products to Install list Select the utility to be installed and then click the arrow button to move it to the Products to Install list Click Install 7 Note To install Status Monitor it is necessary to install SV Microsoft NET Framework 4 0 beforehand eu Setup has detected that the following prerequisites have not been met Microsoft NET Framework 4 0 www microsoft com Finish the installation When Your software is ready to use appears you can use the software To print a test page click the Print a test page checkbox and select the machine Click Finish to exit the wizard Note When you have selected Device settings in Windows I XP the dialog box for device setting will appear after Finish is clicked Configure the settings for options installed on the machine Device settings can be configured after the installation is completed For details refer to the Device Settings in the Printing System Driver User Guide on the DVD ROM If a system restart message appears restart the computer by following the screen prompts This completes the printer driver installation procedure 2 17 2 18 Welcome to the Software Remove Wizard This wizard helps you remove software for your printing system D gt Please close all your applications before continuing Select All _vansai_ conce Uni
7. of procedures other than those specified herein may result in hazardous radiation exposure Cautions for Toner Handling Do not incinerate toner and toner containers Dangerous sparks may cause burn Never open the toner container Do not inhale the toner If you get toner on your hands do not rub your eyes or touch your mouth Wash the toner from your hands For the disposal of the old toner container consult your service technician or dispose of the toner or toner containers in accordance with Federal State and Local rules and regulations xix Convention About the Operation Guide This Operation Guide has the following chapters Chapter 1 Machine Parts This chapter explains the names of parts Chapter 2 Printing Operation This chapter explains how to print from your workstation Chapter 3 Maintenance This chapter explains how to replace the toner container and how to care for your printer Chapter 4 Troubleshooting This chapter explains how to handle printer problems that may occur such as paper jams Chapter 5 Specifications This chapter lists the printer s specifications Conventions This manual uses the following conventions Description Example Italic Typeface Used to emphasize a key word phrase or reference to additional information To replace the toner container refer to Toner Container Replacement on page 3 2 Bold Used to denot
8. refer to the Embedded Web Server RX User Guide 2 8 AS Home 8 Admin Device Information ob Status gt Document Box gt Paper Feed Output Energy Saver Timer Date Time DA Function Settings gt e Network Settings gt Changing Device Information Change the device information of the machine 1 Access Embedded Web Server RX by referring to Accessing Embedded Web Server RX on page 2 6 2 Fromthe Device Settings menu select System Model Host Name Location s n i Last Updated Device Settings System m lt coe m Device Information Host Name KMAE9F21 Asset Number Location General Language English RAM Disk Mode On RAM Disk Size MB 1 32 Override A4 Letter Error Settings Auto Error Clear 5 On Off Low Toner Alert Level On Off For these settings to take effect click Submit and then restart the device and ha 3 Enter the device information and then click Submit IMPORTANT After changing the setting restart the network or turn the machine OFF and then ON To restart the network interface card click Reset in the Management Settings menu and then click Restart Network in Restart Printing Operation Device Information gt Egg Job Status mmon Jo ult Printer gt E mail settings By configuring the SMTP settings you can send E mail notifications on completed jobs To use this function
9. this machine must be connected to a mail server using the SMTP protocol In addition check the following The network environment used to connect this machine to the mail server A full time connection via a LAN is recommended SMTP settings Use Embedded Web Server RX to register the IP address or host name of the SMTP server If limits have been set on the size of E mail messages it may not be possible to send very large E mails The procedure for specifying the SMTP settings is explained below 1 Access Embedded Web Server RX by referring to Accessing Embedded Web Server RX on page 2 6 2 From the Function Settings menu click E mail Model Host Name Location Last Updated SMTP SMTP Protocol Note Settings must be made in SMTP E mail TX Protocol SMTP Server Name SMTP Port Number 25 1 65535 SMTP Server Timeout 10 seconds Authentication Protocol Off Note Make settings here Protocol Test Connection Test Domain Restriction Domain List POP3 Printing Operation 3 Enter the appropriate values to each field Setting Description SMTP Set to send e mail from the machine SMTP Protocol Set SMTP protocol Set the SMTP E mail TX setting to On on the Protocol Settings page SMTP Server Enter the host name or IP address of the SMTP server Name SMTP Port Specify the port number to be used for SMTP Use the SMTP Number defa
10. 6 From the Document Box menu click Custom Box Model Host Name Location u Last Updated Document Box Custom Box p Add Delete 1 3 3 box s Click Add Enter the box details Enter the information for the custom box you want to register The fields to populate are the same as when registering on the machine For details refer to the Using the Operation Panel section of the Advanced Operation Guide Click Submit Printing Operation Printing a document stored in a Custom Box A document stored in a Custom Box can be printed from Embedded Web Server RX 1 Access Embedded Web Server RX by referring to Accessing Embedded Web Server RX on page 2 6 2 From the Document Box menu click Custom Box Model Host Name Location Last Updated Job Box Settings 1 2 2 hawle 3 Click the number or name of the Custom Box in which the document is stored 4 Select the document you wish to print Select the checkbox of the document to be printed Model Host Name Location Home Box Documents Last Mu Le Admin Document Box Custom Box je Box Property Used Area 109 0 KB 200 0 MB Check All None Delete Movef Print ee F O ee rx I Type Eile Name a Date Size Device Information gt Ef Job Status gt E file01 082213 133744984 2013 08 21 23 38 108 0 KB FR Document Box v Custom Box 0 1 Selected 1 1 1 document s Job Box Settings
11. IS PROVIDED BY THE OpenSSL PROJECT AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED INNO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE Original SSLeay License Copyright 1995 1998 Eric Young eay cryptsoft com All rights reserved This package is an SSL implementation written by Eric Young eay cryptsoft com The implementation was written so as to conform with Netscapes SSL This library is free for commercial and non commercial use as long as the following conditions are adhered to The following conditions apply to all code found in this distribution be it the RC4 RSA Ihash DES etc code not just the SSL code The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson tih cryptsoft com Copyright remains Eric Young s and as such any Copyright notices in the code are not t
12. NO EVENT WILL MONOTYPE IMAGING BE LIABLE FOR LOST PROFITS LOST DATA OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES CAUSED BY ABUSE OR MISAPPLICATION OF THE SOFTWARE AND TYPEFACES Massachusetts U S A law governs this Agreement You shall not sublicense sell lease or otherwise transfer the Software and or Typefaces without the prior written consent of Monotype Imaging Use duplication or disclosure by the Government is subject to restrictions as set forth in the Rights in Technical Data and Computer Software clause at FAR 252 227 7013 subdivision b 3 ii or subparagraph c 1 ii as appropriate Further use duplication or disclosure is subject to restrictions applicable to restricted rights software as set forth in FAR 52 227 19 c 2 YOU ACKNOWLEDGE THAT YOU HAVE READ THIS AGREEMENT UNDERSTAND IT AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS NEITHER PARTY SHALL BE BOUND BY ANY STATEMENT OR REPRESENTATION NOT CONTAINED IN THIS AGREEMENT NO CHANGE IN THIS AGREEMENT IS EFFECTIVE UNLESS WRITTEN AND SIGNED BY PROPERLY AUTHORIZED REPRESENTATIVES OF EACH PARTY BY OPENING THIS DISKETTE PACKAGE YOU AGREE TO ACCEPT THE TERMS AND CONDITIONS OF THIS AGREEMENT GPL LGPL This product contains GPL http www gnu org licenses gpl html and or LGPL http www gnu org licenses Igpl html software as part of its firmware You can get the source code and you are permitted to copy redistribute and modify it
13. Paper Jams on page 4 11 Nothing lights on the operation panel even when power is turned on and the fan makes no noise Check that the power cord is properly plugged into the power outlet Turn off the printer s power plug in the power cord securely and try turning on the printer s power again Check that the power switch is in the On position Set the power switch to the On position The printer prints a status page but does not print jobs from the computer Check the printer cable or the interface cable Connect both ends of the printer cable securely Try replacing the printer cable or the interface cable Check program files and application software Try printing another file or using another print command If the problem occurs only with a specific file or application check the printer driver settings for that application The printer is emitting steam in the area around the top tray Check the room temperature to see if it is low or if damp paper was used Tips Depending on the printing environment and the paper s condition the heat generated during printing will cause the moisture in the paper to evaporate and the steam emitted may look like smoke This is not a problem and you can continue printing If the steam concerns you raise the room temperature or replace the paper with a newer dryer paper Printer problems may be solved easily by following the tips
14. a status page is printed out 9 When printing ends the display returns to Ready Printing Operation Embedded Web Server RX If the machine is connected to the network you can configure various settings using Embedded Web Server RX This section explains how to access Embedded Web Server RX and how to change security settings and the host name For details on Embedded Web Server RX refer to the Embedded Web Server RX User Guide Note To fully access the features of the Embedded Web Server RX pages enter the User Name and Password and click Login Entering the predefined administrator password allows the user to access all pages including Document Box and Settings on the navigation menu The factory default setting for the default user with administrator privileges is shown below Login User Name Admin Admin Login Password Upper case and lower case letters are distinguished case sensitive Settings that the administrator and general users can configure in Embedded Web Server RX are as follows A ee Administ General Setting Description er User Device The machine s structure can be checked O Information Configuration Counter About Embedded Web Server RX Job Status Displays all device information including print jobs and job log history Printing Jobs Status Printing Job Log O O Document Box Add or delete document boxes or delete document
15. and click Continue 11 The selected printer is added Printing Operation Printing Operation Printing from Application Software The steps required to print a document created with an application are explained below You can select the printing Paper Size and Output Destination 1 Load the paper required into the paper cassette 2 From the application File menu select Print The Print dialog box displays 3 Click the drop down list of printer names All the printers installed in Windows are listed Click the name of the machine 4 Use Number of copies to enter the number of prints required Up to 999 copies can be entered For Microsoft Word we recommend that you click Options and specify Use printer settings for the Default tray Page range Copies a Number of copies Current page e Pages Enter page numbers and or page ranges separated by commas For example 1 3 5 12 Print what Document Pages per sheet 1 page All pages in range x Scale to paper size No Scaling Prints 5 To start printing click OK options I Draft output T Update fields T Update links Allow A4 Lette IV Background printing I Print PostScript over text T Reverse print order er paper resizing Include with document Document properties T Hidden text T Field codes TT Comments IV Drawing objects Op
16. below When you have encountered a problem that following the above guidelines will not solve try the following e Turn the printer power off and wait for several seconds Then turn on the printer Reboot the computer which sends the print jobs to the printer e Make sure that the procedures for printing are correctly followed in the application software Consult the documentation supplied with the application software Troubleshooting Printed Results Print Quality Problems The tables and diagrams in the following sections define print quality problems and the corrective action you can conduct to solve the problems Some solutions may require cleaning or replacing parts of the printer If the suggested corrective action will not solve the problem call for service Corrective Action Skewed color printout E ABC Conduct color registration using the printer operation panel For details refer to Registration Normal Color registration standard section or Registration Details Color registration detailed section of the Advanced Operation Guide Completely blank printout Check the toner containers Open the printer top cover top tray and check that the toner containers are correctly installed in the printer For more information on installing the toner containers refer to Toner Container Replacement on page 3 2 Check that the application software is correctly operate
17. color calibration either by switching the printer off then on or using the printer operation panel For details refer to Adjust Maintenance Adjust Maintenance selection setting section ofthe Advanced Operation Guide Check the paper chute and the ramp Pull out the paper transfer unit and check for toner on the paper ramp Clean the paper ramp using a soft dry lint free cloth For details refer to Cleaning the Paper Transfer Unit on page 3 8 Clean the main charger units For details refer to LSU Charger LSU Main charger cleaning mode setting section ofthe Advanced Operation Guide Troubleshooting 4 5 Message Account error Press GO Error Messages The following table lists errors and maintenance messages that you can be dealt with by yourself If Call service appears turn off the printer disconnect the power cord and contact your service technician IfCall service or Error Power off is displayed turn off the printer then turn it back on to see if the printer has recovered If the printer has not recovered turn off the printer disconnect the power cord and contact your service representative or authorized service center Some errors cause the alarm to sound To stop the alarm press Cancel Corrective Action This message is displayed when the Job Accounting function is enabled and an attempt to specify job accounting settings or to register or delete an account fails To ret
18. im unmittelbaren Gesichtsfeld platziert werden Disclaimer We will not be liable to customers or any other person or entity for any loss or damage caused or alleged to be caused directly or indirectly by equipment sold or furnished by us including but not limited to any interruption of service loss of business or anticipatory profits or consequential damages resulting from the use or operation of the equipment or software Energy Saving Control Function The device comes equipped with a Low Power Mode where energy consumption is reduced after a certain amount of time elapses since the device was last used as well as a Sleep where printer functions remain in a waiting state but power consumption is still reduced to a minimum when there is no activity with the device within a set amount of time Low Power Mode The device automatically enters Low Power Mode when 1 minute has passed since the device was last used The amount of time of no activity that must pass before Low Power Mode is activated may be lengthened For more information refer to Low Power Timer Low Power Mode timer timeout time section of the Advanced Operation Guide Sleep The device automatically enters Sleep when 15 minutes have passed since the device was last used The amount of time of no activity that must pass before Sleep is activated may be lengthened For more information refer to Sleep Timer Sleep timer timeout setting section of the Advanced Opera
19. or Typefaces except that you may make one backup copy You agree that any such copy shall contain the same proprietary notices as those appearing on the original 5 This License shall continue until the last use of the Software and Typefaces unless sooner terminated This License may be terminated by Monotype Imaging if you fail to comply with the terms of this License and such failure is not remedied within thirty 30 days after notice from Monotype Imaging When this License expires or is terminated you shall either return to Monotype Imaging or destroy all copies of the Software and Typefaces and documentation as requested 10 11 12 13 14 You agree that you will not modify alter disassemble decrypt reverse engineer or decompile the Software Monotype Imaging warrants that for ninety 90 days after delivery the Software will perform in accordance with Monotype Imaging published specifications and the diskette will be free from defects in material and workmanship Monotype Imaging does not warrant that the Software is free from all bugs errors and omissions THE PARTIES AGREE THAT ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE EXCLUDED Your exclusive remedy and the sole liability of Monotype Imaging in connection with the Software and Typefaces is repair or replacement of defective parts upon their return to Monotype Imaging IN
20. over SSL On Off HTTPS On Off IPSec On Off LAN Interface Auto 10BASE Half 10BASE Full 100BASE Half 100BASE Full 1000BASE T Security Level High Low Note After all network related settings have been done turn amp the machine OFF and ON again This is mandatory to make the settings effective 2 3 2 4 Adjust Maintenance gt gt gt Print Network Status Page Printing a Network Interface Status Page You can print out a status page for the network interface The network status page shows the network addresses and other information under various network protocols about the network interface Adjust Maintenance Adjust Maintenance is used to adjust the print quality and to carry out printer maintenance The options available in Adjust Maintenance are as follows Color Calibration e Registration Normal e Registration Details e Restart Printer Service IMPORTANT Service is primarily a menu used by service personnel for maintenance work There is no need for customers to use this menu 1 Press MENU 2 Press A or V repeatedly until Adjust Maintenance gt appears Press gt while Adjust Maintenance gt is displayed Press A or V repeatedly until gt Service gt appears Press D aoa KR W Press A or V repeatedly until gt gt Print Network Status Page appears N Press OK A question mark appears Press OK Processing appears and
21. privileges If the Welcome to the Found New Hardware Wizard dialog box displays select Cancel If the autorun screen is displayed click Run setup exe If the user account management window appears click Yes Allow 2 Click View License Agreement and read the License Agreement Click Accept 3 Select Custom Install tab 4 Select the device to be installed and click the arrow button to move itto the Products to Install list The following buttons are available This button is used to switch the display between icon and text display This button is used to select multiple items If the target device is not displayed press this button to directly select the device to be used ah ss Printing Operation ices and utilities tne Products to instant Products to Install ices and utilities Intl devices and utilities Move tne items to tne Prous to Instat ist pst Montar Finished Your software is ready to use Details Product Status Monitor FONTS Uninstaller Detail Installed Installed Installed Installed Gb Print a test page 1 Enable event notification 2 Show Quick Print tab Printing Operation 5 Select the device to be installed and driver to be installed and then
22. unit you must use the dry cloth CAUTION Components inside the fuser cover are hot Do not touch it with your hands as it may result in burn injury 1 Press the lever to release the lock 2 Pull out the front cover Maintenance Maintenance 3 Wipe away the paper dust on the registration roller and the paper ramp using the dry cloth Paper Transfer Unit Duplex Unit Paper Ramp Q DA Transfer Belt Y Black FL Registration y Roller Metal Transfer Roller Black Note Be careful not to touch the black transfer roller and amp black transfer belt during cleaning as this may adversely affect print quality 4 Push the front cover back in completely Note Take care not to get your hands caught in the front cover when you close it 3 9 Maintenance Troubleshooting 4 Troubleshooting This chapter contains explanations on the following topics General Guidelines 4 2 Print Quality Problems 4 3 Error Messages 4 6 Clearing Paper Jams 4 11 If a problem cannot be corrected contact your service technician 4 1 Symptom General Guidelines The table below provides basic solutions for problems you may encounter with the printer We suggest you consult this table to troubleshoot the problems before calling for service Check Items Corrective Action Print quality is not good Refer to Print Quality Problems on page 4 3 Paper is jammed Refer to Clearing
23. 24 seconds or less Memory Standard 512 MB Maximum 1 536 MB Operating Systems Microsoft Windows 2000 XP Vista 7 8 Windows Server 2003 2008 2012 Apple Macintosh OS 10 5 or later Interface USB USB Interface 1 USB Memory Slot 1 Network Network Interface 1 10 BASE T 100 BASE TX 1000BASE T Option eKUIO slot 1 SSD HD 6 HD 7 Network Interface Kit IB 50 Wireless Network Interface Kit IB 51 Monthly Duty Average 3 000 pages plain A4 paper Maximum 100 000 pages plain A4 paper Paper Sizes Cassette Envelope C5 Executive Letter Legal A4 B5 A5 A6 ISO B5 Custom Oficio II 216 x 340 mm 16K Statement Folio Cassette Envelope Monarch Envelope 10 Envelope DL Envelope C5 Executive Letter Optional Paper Feeder PF 500 PF 510 Legal A4 B5 A5 Envelope 9 Envelope 6 ISO B5 Custom Oufuku Hagaki Oficio II 216 x 340 mm 16K Statement Folio Youkei 2 Youkei 4 MP Tray Envelope Monarch Envelope 10 Envelope DL Envelope C5 Executive Letter Legal A4 B5 A5 A6 B6 Envelope 9 Envelope 6 ISO B5 Custom Hagaki Oufuku Hagaki Oficio Il 216 x 340 mm 16K Statement Folio Youkei 2 Youkei 4 t After 16 pages the printing speed becomes 14 ppm Specifications 5 1 Item Description Paper Typest Cassette Plain preprinted bond recycled rough letterhead color prepunched high quality Optio
24. 65 Ibs t When using CUSTOM 1 to 8 use the MP tray for paper sizes smaller than 105 x 148 mm 4 1 8 x 5 13 16 inches The MP tray can be used with paper sizes over 70 x 138 mm 2 3 4 x 5 7 16 inches tt Sound pressure level at bystander position front in accordance with EN ISO 7779 Specifications A1 We recommend the use of our own brand supplies We will not be liable for any damage caused by the use of third party supplies in this machine QUALITY CERTIFICATE ach ne Pas passed lity controls and TA Triumph Adler GmbH Betriebsst tte Norderstedt Ohechaussee 235 22848 Norderstedt Germany First edition 2013 10 2PPGEENOOO
25. FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT INDIRECT INCIDENTAL SPECIAL EXEMPLARY OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES LOSS OF USE DATA OR PROFITS OR BUSINESS INTERRUPTION HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY WHETHER IN CONTRACT STRICT LIABILITY OR TORT INCLUDING NEGLIGENCE OR OTHERWISE ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE The licence and distribution terms for any publically available version or derivative of this code cannot be changed i e this code cannot simply be copied and put under another distribution licence including the GNU Public Licence Compliance and Conformity This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined b
26. IF IT WORX IT S USER MANUAL COLOUR PRINTER 3 on P C3060DN Operation Guide Contents Machine Parts Components at the Front of the Printer n 1 2 Components at the Left of the Printer n 1 2 Internal Components sssaaa oeodna ai 1 3 Components at the Rear of the Printer n 1 3 Operation Panel su 1 4 Printing Operation Changing Network Interface Parameters 2 2 Printing a Network Interface Status Page 2 4 Embedded Web Server RX_ ii 2 5 Installing the Printer Driver ii 2 14 Printing from Application Software 2 21 Printing by AirPrint uunaiiic 500000 0000 nn ins 2 22 Status Monitor siii 2 23 Energy Saver Function ri 2 27 Maintenance General Information sg ra 3 2 Toner Container Replacement ursuessneneannnnnnnnnnnannnnnnnnn 3 2 Replacing the Waste Toner BOX usnsensnnnnsnnnnnnnnnnnnnnnnnnnnnnnnnnnn 3 6 Cleaning the Printer ul 3 8 Troubleshooting General Guidelines i iiii iii 4 2 Print Quality Problems ieri 4 3 Error Messages 4 6 Cleaning Paper Jams iaia 4 11 Specifications Legal and Safety Information CAUTION NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION Notice on Software SOFT
27. O Replace MK Replace Maintenance Kit which is displayed on the message display Replacement of the maintenance kit is necessary at every 200 000 images of printing and requires professional servicing Contact your service technician Replace toner Cp Ep v4 Replace toner Clean printer Two message items are displayed alternately Toner has run out in the toner container s Replace the toner container using a new toner kit for the particular color The printer does not operate when this message is displayed For example if Replace toner C K is displayed replace the cyan and the black toner containers SSD error Press GO A SSD error has occurred Look at the error code given in place of and refer to Storage Error Codes on page 4 10 To ignore the SSD error press GO Toner low Replace the toner container using a new toner kit Color of the toner container that needs to be replaced is represented by c Cyan M Magenta y Yellow and K C M Y K Black Top tray The top tray has become full approx 250 pages You must remove all printed pages paper full from the top tray When the printer detects that the top tray is empty again the printer will continues printing into the top tray Unknown toner installed We will not be liable for any damage caused by the use of third party supplies in this machine Unknown toner PC CiM Xy K USB mem
28. Status Monitor automatically shuts down after 7 minutes if it is not being used Status Monitor Display The display of the Status Monitor is as follows Quick View State The status of the printer is displayed using icons Detailed information is displayed when the Expand button is clicked sa 9999I 30 44 56 59 61 Settings icon Expand button Alert Tab Toner Status Tab Paper Tray Status Tab Printing Progress Tab Detailed information is displayed by clicking on each icon tab 2 23 Printing Progress Tab The status of the print jobs is displayed fol __ m x 0 100 100 100 100 Job Name Printed Status document 01 082 Printing Status icon Job list Select a job on the job list and it can be canceled using the menu displayed with a right click Paper Tray Status Tab Information is displayed about the paper in the printer and about the amount of paper remaining de _ 2999 0 30 100 100 100 100 a Name Size Type LA MP Tray LetterR Plain Cassette 1 A4 R Plain Toner Status Tab The amount of toner remaining is displayed ren _ E N S A 3 100 100 100 Toner Black Cyan Magenta Yellow 2 24 Printing Operation Alert Tab If an error occurs a notice is displayed using a 3D image and a mess
29. WARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER S EMULATION MODE The printer is factory set to emulate the PCL Notice The information in this guide is subject to change without notification Additional pages may be inserted in future editions The user is asked to excuse any technical inaccuracies or typographical errors in the present edition No responsibility is assumed if accidents occur while the user is following the instructions in this guide No responsibility is assumed for defects in the printer s firmware contents of its read only memory This guide any copyrightable subject matter sold or provided with or in connection with the sale of the page printer are protected by copyright All rights are reserved Copying or other reproduction of all or part of this guide any copyrightable subject matter without the prior written consent of Copyright owner is prohibited Any copies made of all or part of this guide any copyrightable subject must contain the same copyright notice as the material from which the copying is done Regarding Tradenames PRESCRIBE and KPDL are trademarks of Kyocera Corporation e Microsoft Windows Windows XP Windows Server 2003 Windows Vista Windows Server 2008 Windows 7 Windows Server 2012 Windows 8 and Internet Explorer are registered trademarks or trademarks of Microsoft Corporation in the U S A and or other countries PCL is a trademark of Hewlett Packard Company e Adobe Acr
30. a problem with this website s security certificate is displayed configure the certificate For details on Certificates refer to the Embedded Web Server RX User Guide You can also continue the operation without configuring the certificate 3 Select a category from the navigation bar on the left of the screen When you log in to the machine as an administrator you will see Device Settings Function Settings Network Settings Security Settings and Management Settings Printing Operation Printing Operation Changing Security Settings This section explains how to change the security settings 1 Access Embedded Web Server RX by referring to Accessing Embedded Web Server RX on page 2 6 2 Fromthe Security Settings menu select the setting you want to configure The configurable settings are Device Security Network Security and Certificates Device Information 4 RE Source p Job Status Cassette 1 MP Tray Color Black Cyan Magenta Yellow Model Host Name Location 2 Last Updated e ea rt Status Ready Sleeping Size Type Capacity Status A4 Pian 500 Letter Pian 150 Status Note The configurable settings within Device Security and Network Security can also be configured from the machine s System Menu For details refer to the Using the Operation Panel section of the Advanced Operation Guide For details on settings related to certificates
31. age a gt o g I I JS R 0 30 100 100 100 100 a Cover open The printing system s left cover is open Close it securely Ready Status Monitor Context Menu The following menu is displayed when the settings icon is clicked Settings icon _ U 5 5 I 0 30 100 100 100 100 Configure Notification Ready Exit e Configure If the printer is connected to a TCP IP network and has its own IP address use a web browser to access the Embedded Web Server RX to modify or confirm the network settings For more information refer to the Embedded Web Server RX User Guide This menu is not displayed when using USB connection e Notification This sets the display of the Status Monitor For details refer to Status Monitor Notification Settings on page 2 26 Exit Exits the Status Monitor Printing Operation 2 25 2 26 Status Monitor Notification Settings The Status Monitor settings and event list details are displayed Enables event notification Available events Events Sound file Text to Speech Paper jam Add paper Sleep Add toner Toner low Not connected Select whether notification is performed when an error in the event list OCCUFS 1 Select Enable event notification If this setting is set to Off then the Status Monitor will not start u
32. atically resumed after a preset period of time Multi copies cannot be printed because RAM disk is disabled or the SSD is not installed Try adding more memory or installing SSD and configuring the RAM disk settings No power supply Cassette This message is displayed when the optional paper feeder PF 510 is not connected to a power source and COATED coated paper is selected as the paper type setting Connect it to a power source via the printer Not completed Press GO The restarting of the option network failed Please restart it again Paper jam 44 4 EEE HEHEHE HH A paper jam has occurred The location of the paper jam is indicated in place of the s For details refer to Clearing Paper Jams on page 4 11 Paper loading The selected cassette is being prepared Paper path error There is no paper cassette in the feeder or the cassette is not inserted properly After reinserting the paper cassette you should be able to print When two or more optional feeders are installed and the lowest one is selected the same message will appear if any of the upper paper feeder and the printer cassette is improperly installed Troubleshooting Message Corrective Action RAM disk error Press GO A RAM disk error has occurred Look at the error code given in place of and refer to Storage Error Codes on page 4 10 To ignore the RAM disk error press G
33. autionary Labels The printer bears any of the following labels CAUTION ACHTUNG ATTENTIO HOT SURFACE HEISSEOBERFL CHE TEMPERATURE ATTENCION _ ATTENZIONE EXTERIDA CALIENTE SUPERFICIE CHE SCOTIA N High temperature inside Do A not touch parts in this area because there is a danger of getting burned Label inside the printer Laser radiation warning ANGER fianco SE ATENIRNE GAR MONET NE RT RRM ZT RSAMIURH NERI AVOID DIRECT EXPOSURE TO BEAM EVITARE L ESPOSIZIONE AL FASCIO n Fil DA ATTENTION CLASE 3B RAYONNEMENT PRECAUCION CLASSE 3B RADIACIONE SRE AIBA AA ai TREAT LEAN GAS DOUVERTURS LASER INVISIBLE CUANDO SE ABRE FART ROA MAI TARR EXPOSITION DANGEREUSE AU FAISCEAU EVITAR EXPONERSE AL RAYO 918 CLASS 3B 8 4 M0 AMS VORSICHT KLASSE 38 UNSICHTBARE VARO AVATTAESSA OLET ALTTIINA LUOKAN 214 3ix o amp AJ 3B N KYM TT M LLE LASERS TEILYLLE we se GE FFNET ALA KATSO SATEESEEN ES CTER CDS AIBAARL Ht NICHT DEM STRAHL AUSSETZEN 3 TEIL LEBER MIST SER P C3060DN xii CDRH Regulations The Center for Devices and Radiological Health CDRH ofthe U S Food and Drug Administration implemented regulations for laser products on August 2 1976 These regulations apply to laser products manufactured after August 1 1976 Compliance is mandatory for products marketed in the United States A label indicating compliance with the CDRH regulations must be attached to laser pr
34. cally activates energy saving mode when the machine is idle for a certain period of time Although it takes the machine a slight amount of time to return to READY mode when in energy saving mode a significant reduction in energy XV xvi ENERGY STAR consumption is possible It is recommended that the machine be used with the activation time for energy saving mode set to the default setting Energy Star ENERGY STAR Program We have determined as a participating company in the International Energy Star Program that this product is compliant with the standards laid out in the International Energy Star Program ENERGY STAR is a voluntary energy efficiency program with the goal of developing and promoting the use of products with high energy efficiency in order to help prevent global warming By purchasing ENERGY STAR qualified products customers can help reduce emissions of greenhouse gases during product use and cut energy related costs Left 400 mm 16 inches Installation Precautions Environment A CAUTION Avoid placing the printer on or in locations which are unstable or not level Such locations may cause the printer to fall This type of situation presents a danger of personal injury or damage to the printer Avoid locations with humidity or dust and dirt If dust or dirt becomes attached to the power plug clean the plug to avoid the danger of fire or electrical shock Avoid locations near
35. d Full single color printout Check the main charger unit Open the left cover and check that the main charger unit is correctly installed Dropouts or stray dots Clean the main charger units For details refer to LSU Charger LSU Main charger cleaning mode setting section of the Advanced Operation Guide Troubleshooting 4 3 Printed Results Corrective Action Black or white vertical streaks ABC ABC 123 123 Direction of Paper Feed Check the operation panel for toner Ifthe Toner low C M Y K message is displayed with color description install a new toner kit for the color To replace the toner container refer to Toner Container Replacement on page 3 2 Clean the main charger units For details refer to LSU Charger LSU Main charger cleaning mode setting section of the Advanced Operation Guide Refresh drum Perform the following procedures on the operation panel and try cleaning the drum surface using the printer s built in cleaning system Press MENU Press A or V repeatedly until Adjust Maintenance gt appears Press Press A or V repeatedly until gt Service gt appears Press Press A or V repeatedly until gt gt Drum appears Press OK twice The message display shows Please wait After approx 3 minutes the display returns to Ready ooh WN Faint or blurred printing ABC ABC 123 123 Clean the main charger units For details ref
36. e buttons on the To start printing click OK software Braket Bold Used to denote operation panel Press GO to resume printing keys Note Used to provide additional or useful Note Check with your network information about a function or 2 administrator for the network address feature settings Important Used to provide important IMPORTANT Ensure paper is not folded information curled or damaged Caution Cautions are statements that CAUTION Components inside the fuser no 1 damage as a cover are hot Do not touch it with your i hands as it may result in burn injury Warning Used to alert users to the possibility WARNING High voltage is present in the of personal injury charger section Machine Parts 1 Machine Parts This chapter provides explanations and illustrations for you to determine the parts and their functions Try to be familiar with the names and functions of these parts for correct use and optimal performance This chapter contains explanations on the following topics Components at the Front of the Printer 1 2 Components at the Left of the Printer 1 2 Internal Components 1 3 Components at the Rear of the Printer 1 3 Operation Panel 1 4 1 1 Components at the Front of the Printer Operation Panel Front Cover Paper Stopper Top Cover Top Tray MP Multi Purpose Tray Paper Cassette Power Switch NO GG Born Components at the Left of the Printer 11 12 1314
37. er to LSU Charger LSU Main charger cleaning mode setting section of the Advanced Operation Guide Make sure the paper type setting is correct the paper being used For details refer to Paper Settings section of the Advanced Operation Guide Conduct color calibration either by switching the printer off then on or using the printer operation panel For details refer to Color Calibration section of the Advanced Operation Guide Try adjusting the color control settings using the printer driver Check the operation panel If the Toner low C M Y K message is displayed with color description install a new toner kit for the color To replace toner refer to Toner Container Replacement on page 3 2 Refresh drum Perform the following procedures on the operation panel and try cleaning the drum surface using the printer s built in cleaning system Press MENU Press A or V repeatedly until Adjust Maintenance gt appears Press Press A or V repeatedly until gt Service gt appears Press D Press A or V repeatedly until gt gt Drum appears Press OK twice The message display shows Please wait After approx 3 minutes the display returns to Ready ou hth WN 4 4 Troubleshooting Printed Results Corrective Action Grey background Clean the main charger units For details refer to LSU Charger LSU Main charger cleaning mode setting section ofthe Advanced Operation Guide Conduct
38. h off and contact your service representative or authorized service center Error Power off F000 The printer controller and operation panel cannot exchange data Turn the printer off and unplug it from the mains power supply Then contact your service representative or authorized service center See the back page of this manual for the relevant phone numbers Exceeded Max output Press GO This message is displayed when the Job Accounting function is enabled and an attempt has been made to exceed the print limit set for each account To return the printer to the print ready status press GO For more information refer to Job Accounting Job Accounting selection setting section of the Advanced Operation Guide Format SSD The SSD installed in the printer is not formatted and therefore cannot be read or written ID error Illegal Account Press GO The user ID entered for a private job or a stored job is not correct Check the user ID that you specified on the printer driver For more information refer to Job Box section of the Advanced Operation Guide This message is displayed when the Job Accounting function is enabled and no account is set for a transmitted print job or the specified account is not registered the incorrect account is set To return the printer to the print ready status press GO For more information refer to Job Accounting Job Accounting select
39. he power plug from the outlet when performing cleaning operations If dust accumulates within the printer there is a danger of fire or other trouble It is therefore recommended that you consult with your service representative in regard to cleaning of internal parts This is particularly effective if accomplished prior to seasons of high humidity Consult with your service representative in regard to the cost of cleaning the internal parts of the printer Other Precautions Do not place heavy objects on the printer or cause other damage to the printer Do not open the top left rear cover turn off the main switch or pull out the power plug during printing During printing some ozone is released but the amount does not cause any ill effect to one s health If however the printer is used over a long period of time in a poorly ventilated room or when printing an extremely large number of copies the smell may become unpleasant To maintain the appropriate environment for print work it is suggested that the room be properly ventilated Do not touch electrical parts such as connectors or printed circuit boards They could be damaged by static electricity Do not attempt to perform any operations not explained in this handbook If the printer will not be used for an extended period of time remove the paper from the cassette return it to its original package and reseal it CAUTION Use of controls or adjustments or performance
40. ic bag contained in the toner kit and discard it later according to the local code or regulations for waste disposal Plastic Bag A Take the new toner container out of the toner kit a Shake the new toner container 5 or 6 times as shown in the figure in order to distribute the toner evenly inside the container Do not press too firmly on the center of the toner container or touch the toner feed slot Maintenance Toner Feed Slot 6 Set the new toner container in the printer as shown in the figure below 7 Push down on the top of the toner container to install it firmly in place Use the same procedure to replace the other color toner containers 8 Close the top cover top tray Note Ifthe top cover top tray does not close check that the I new toner container is installed correctly in step 7 After use always dispose of the toner container and the waste toner box in accordance with Federal State and Local rules and regulations Proceed to the next section 3 6 Old Waste Toner Box Plastic Bag Replacing the Waste Toner Box Replace the waste toner box when the Check waste toner box message is displayed A new waste toner box is included with the toner kit The waste toner box needs to be replaced before the printer will operate 1 Open the left cover 2 While holding the waste toner box press the lock lever and then gently remove the waste toner box Note Rem
41. ing If you want to print from a different paper source press A or V to display Use alternative and you can change the source for paper feeding After selecting a paper source and pressing MENU Paper Settings gt appears By pressing the A the paper type settings menu appears After setting the correct paper type press OK and printing starts Load MP Tray A4 PLAIN There is no paper cassette installed in the printer that matches the paper size and paper type of the print job Set paper in the MP tray Press GO to resume printing Note that feeding the paper having a paper size which does not match the current paper size from the MP tray can cause paper jam If you want to print from a different paper source press A or V to display Use alternative and you can change the source for paper feeding After selecting a paper source and pressing MENU Paper Settings gt appears By pressing the A the paper type settings menu appears After setting the correct paper type press OK and printing starts Low security This message is displayed when Low was selected in Security Level Memory overflow Press GO No multi copies Press GO The total amount of data received by the printer exceeds the printer s internal memory Try adding more memory Press GO to resume printing You can abandon printing by pressing Cancel If Auto Error Clear is set to On printing will be autom
42. inotype Hell AG ITC Avant Garde Gothic ITC Bookman ITC ZapfChancery and ITC Zapf Dingbats are registered trademarks of International Typeface Corporation Monotype Imaging License Agreement 1 Software shall mean the digitally encoded machine readable scalable outline data as encoded in a special format as well as the UFST Software 2 You agree to accept a non exclusive license to use the Software to reproduce and display weights styles and versions of letters numerals characters and symbols Typefaces solely for your own customary business or personal purposes at the address stated on the registration card you return to Monotype Imaging Under the terms of this License Agreement you have the right to use the Fonts on up to three printers If you need to have access to the fonts on more than three printers you need to acquire a multi user license agreement which can be obtained from Monotype Imaging Monotype Imaging retains all rights title and interest to the Software and Typefaces and no rights are granted to you other than a License to use the Software on the terms expressly set forth in this Agreement 3 To protect proprietary rights of Monotype Imaging you agree to maintain the Software and other proprietary information concerning the Typefaces in strict confidence and to establish reasonable procedures regulating access to and use of the Software and Typefaces 4 You agree not to duplicate or copy the Software
43. inter is certified as a Class 1 laser product under the U S Department of Health and Human Services DHHS Radiation Performance Standard according to Radiation Control for Health and Safety Act of 1968 This means that the printer does not produce hazardous laser radiation Since radiation emitted inside the printer is completely confined within protective housings and external covers the laser beam cannot escape from the printer during any phase of user operation Laser Notice This printer is certified in the U S to conform to the requirements of DHHS 21 CFR Subchapter for Class 1 laser products and elsewhere is certified as a Class laser product conforming to the requirements of IEC EN 60825 1 2007 DANGER CLASS 3B INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure Radio Frequency Transmitter This machine contains a transmitter module We the manufacturer hereby declare that this equipment page printer model P C3060DN is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Radio Tag Technology In some countries the radio tag technology used in this equipment to identify the toner container may be subject to authorization and the use of this equipment may consequently be restricted xi C
44. ion setting section of the Advanced Operation Guide Job not stored Press GO Printing using the Job Box function failed because there was insufficient space available on the hard disk or RAM disk or because the RAM disk was disabled when demounting the hard disk To print an error report and return the printer to the print ready status press GO Job restricted Press GO This message is displayed when printing was attempted despite the Job Account function being on with Restriction applied as the job limit for each job account To return the printer to the print ready status press GO For more information refer to Job Accounting Job Accounting selection setting section of the Advanced Operation Guide Troubleshooting Message Corrective Action KPDL error Press GO Current print processing cannot continue because of occurrence of KPDL error which is categorized by To print out an error report display gt gt Error Report from the menu system and select On Press GO to resume printing You can abandon printing by pressing Cancel If Auto Error Clear is set to On printing will be automatically resumed after a preset period of time Load Cassette A4 PLAIN The paper cassette matching the paper size and paper type of the print job is empty Load paper into the paper cassette as displayed in place of Press GO to resume print
45. ion using the command Troubleshooting Clearing Paper Jams If the paper jammed in the paper transport system or no paper sheets were fed at all the Paper jam message appears and the location of the paper jam the component where the paper jam has occurred is also indicated The printer automatically goes off line when this message is displayed Remove jammed paper After removing jammed paper the printer will re start printing Possible Paper Jam Locations The figure below explains the printer s paper paths including the options The locations where paper jams might occur are also shown here with each location explained in the table below Paper jams can occur in more than one component on the paper paths MP Tray Paper Cassette Paper Feeder PF 500 PF 510 Paper Jam Message Description Reference Page Paper jam Paper is jammed inside the printer page 4 12 Printer paper cassette or MP tray page 4 13 page 4 14 Paper jam Cassette 2 to 4 Paper is jammed at the optional paper page 4 14 feeder s cassette Troubleshooting P General Considerations for Clearing Jams Bear in mind the following considerations when attempting jam removal CAUTION When pulling the paper pull it gently so as not to tear it Torn pieces of paper are difficult to remove and may be easily overlooked deterring the jam recovery If paper jams occur frequently
46. n to support new product planning and development The information gathered is anonymous it cannot be associated to any specific individual and the data is intended to be used anonymously Toner Container Replacement The toner container in the printer should be replaced as soon as the message display shows Toner low or soon after If you continue to use the printer eventually the toner supply will be exhausted at which point the printer will stop printing and the Replace toner C M Y K message will be shown instructing you to install a new toner kit Frequency of Toner Container Replacement The life of the toner containers depends on the amount of toner required to accomplish your printing jobs According to ISO IEC 19798 and EcoPrint switched off the toner container can print as follows A4 Letter paper is assumed Toner Color Life of the Toner Container Printable pages Black 12 000 images Cyan 10 000 images Magenta 10 000 images Yellow 10 000 images Note The toner container packed with the new printer has to fill amp up the system when operating the first time Therefore only 50 of the first toner kits can be used for printing For example P C3060DN can print 6 000 Black amp White images using the black starter toner container Toner Kits For best results we recommend that you only use genuine Parts and Supplies The toner kits are supplied in 4 different colors cyan magenta yellow and black
47. nal Paper and custom Feeder PF 500 Cassette Plain preprinted labels bond recycled rough letterhead color prepunched Optional Paper envelope cardstock coated thick high quality and custom Feeder PF 510 MP Tray Plain transparency preprinted labels bond recycled vellum rough letterhead color prepunched envelope cardstock coated thick high quality and custom Paper Feed Cassette 500 sheets 80 g m Source Capacity MP Tray 150 sheets 80 g m Margin 4 mm left right top and bottom Output Tray Top Tray 250 sheets 80 g m Capacity Operation Temperature 10 to 32 5 C 50 to 90 5 F Environment Relative 15 to 80 Humidity Altitude 2 500 m 8 202 feet maximum Illumination 1 500 lux maximum Power Source 120 V 60 Hz max 9 2 A U S A Canada 220 240 V 50 Hz 60 Hz max 4 7 A European countries Max allowable voltage fluctuation 10 Max allowable frequency fluctuation 2 Power Maximum 120 V models 1 103 W or less Consumption 220 240V models 1 103 W or less During Printing 120 V models 554 W 220 240 V models 529 W During Standby 120 V models 79 W 220 240 V models 76 W During Sleep 120 V models 4 W Mode 220 240 V models 4 W Power Off ow Operating During Printing LpA 55 dB A Noise During Standby LpA 36 dB A During Sleep Mode immeasurably low Dimensions W x D x H 345 x 518 x 480 mm 13 5 8 x 20 2 5 x 18 9 10 Weight Approx 29 5 kg
48. name and password used to log in to the operating system Printing Operation 1 Insert the DVD ROM 2 Double click the GEN_LIB icon 3 Double click OS X 10 5 or higher eno GENLUB eo EEr ela a Devices SHARED PLACES LS l Common files Document OSX 10 5 or higher ja Readime pdt x ose es ane OSX 10 5 or higher oO 4 Lale Elne oJ s a Devices A SHARED gt OSX 10 5 build AS PDL Setup buil nu Welcome 5 Introduction Read Me You will be guided through the steps necessary to install this software Continue eoe System Preferences aLr ShowAl Personal B 5 ee aa Hardware Lal O CDs amp DVDs Displays Energy Keyboard Mouse Z Internet amp Wireless u Q l 2 Printing Operation Security Spotlight Universal amp Privacy Access ce Sound ro Sharing Speech Time Machine Startup Disk Double click Brand Name OS X 10 5 The printer driver installation program starts up Install the printer driver as directed by the instructions in the installation software This completes the printer driver installation If a USB connection is used the machine is automatically recognized and connected If an IP connection is used the settings below are required Open System Preferences and click Print amp Scan 2 19 Open Print Queue Options amp Supplies idle
49. nced Operation Guide Troubleshooting 4 10 Storage Error Codes SSD Errors Code Meaning 03 The SSD is write protected using command operation Remove the write protection using the command 04 There is no available SSD space Delete unnecessary files etc in order to free up space 05 The desired file does not exist in the SSD Stored the file in the SSD 10 The file stored in the SSD is write protected using command operation Remove the write protection using the command USB Memory Errors Code Meaning 01 The amount of data that can be saved at once has been exceeded Split the large file into multiple smaller files The USB memory is write protected Remove the write protection The USB memory is broken Even if the problem is not solved format the USB memory with the device or use the new USB memory compatible with the printer 04 There is no available space Delete unnecessary files etc in order to free up space RAM Disk Errors Code Meaning 02 RAM disk mode is off Turn RAM disk mode On from the operation panel 03 The RAM disk is write protected using command operation Remove the write protection using the command 04 No disk space Purge unnecessary files or increase the RAM disk size 05 The desired file does not exist in the RAM disk Stored the file in the RAM disk 10 The file stored in the RAM disk is write protected using command operation Remove the write protect
50. nction 2 27 2 1 Changing Network Interface Parameters This printer supports TCP IP TCP IP IPv6 NetWare AppleTalk IPP SSL Server and the IPSec protocols and Security Level The table below shows the items required for each of the settings Configure the printer s network parameters as appropriate for your PC and your network environment For details of the procedure refer to the Using the Operation Panel section of the Advanced Operation Guide Note When Embedded Web Server RX is used network parameters and security settings can be conveniently changed and checked from your PC For more information refer to Embedded Web Server RX User Guide If the optional IB 50 or IB 51 is installed then NetWare and AppleTalk settings are possible For details refer to Optional Network section of the Advanced Operation Guide Menu Submenu Setting Network TCP IP On Off DHCP On Off Auto IP On Off IP Address IP address Subnet Mask IP address Gateway IP address Bonjour On Off TCP IP IPv6 On Off RA Stateless On Off DHCPv6 On Off Security I F Block USB Host Block Unblock USB Device Block Unblock Option I F Block Unblock USB Storage Block Unblock WSD PRINT On Off Enhanced WSD On Off EnhancedWSD SSL On Off IPP On Off Printing Operation Printing Operation Menu Submenu Setting SSL Server On Off DES On Off 3DES On Off AES On Off IPP
51. nstalling the Software Perform the following procedure to delete the Software from your computer Note Uninstallation on Windows must be done by a user SV logged on with administrator privileges 1 Click Start button on the Windows and then select All Programs name of offer company and Uninstall Product Library to display the Uninstall Wizard 2 Place a check in the check box of the software to be deleted Click Uninstall 3 Ifa system restart message appears restart the computer by following the screen prompts This completes the software uninstallation procedure Note The software can also be uninstalled using the Product amp Library In the Product Library installation screen click Uninstall and follow the on screen instructions to uninstall the software Installing Printer Driver in Macintosh The machine s printer functionality can be used by a Macintosh computer The following is an explanation for installation in MAC OSX 10 7 Z Note Installation on MAC OS must be done by a user logged I on with administrator privileges When printing from a Macintosh computer set the machine s emulation to KPDL or KPDL Auto For details refer to the Using the Operation Panel section of the Advanced Opera tion Guide If connecting by Bonjour enable Bonjour in the machine s network settings For details refer to the Using the Operation Panel section of the Advanced Operation Guide In the Authenticate screen enter the
52. o be removed If this package is used in a product Eric Young should be given attribution as the author of the parts of the library used This can be in the form of a textual message at program startup or in documentation online or textual provided with the package Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the copyright notice this list of conditions and the following disclaimer 2 Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution 3 All advertising materials mentioning features or use of this software must display the following acknowledgement This product includes cryptographic software written by Eric Young eay cryptsoft com The word cryptographic can be left out if the rouines from the library being used are not cryptographic related 4 Ifyou include any Windows specific code or a derivative thereof from the apps directory application code you must include an acknowledgement This product includes software written by Tim Hudson tih cryptsoft com THIS SOFTWARE IS PROVIDED BY ERIC YOUNG AS IS AND ANY EXPRESS OR IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
53. obat Adobe Reader and PostScript are trademarks of Adobe Systems Incorporated Ethernet is a registered trademark of Xerox Corporation e NetWare is a registered trademark of Novell Inc IBM is a registered trademark of International Business Machines Corporation AppleTalk Bonjour Macintosh and Mac OS are trademarks of Apple Inc registered in the U S and other countries All European language fonts installed in this machine are used under licensing agreement with Monotype Imaging Inc Helvetica Palatino and Times are registered trademarks of Linotype GmbH e ITC Avant Garde Gothic ITC Bookman ITC ZapfChancery and ITC ZapfDingbats are registered trademarks of International Typeface Corporation vi e UFST MicroType fonts by Monotype Imaging Inc are installed in this machine AirPrint and the AirPrint logo are trademarks of Apple Inc e iOS is a trademark or registered trademark of Cisco in the U S and other countries and is used under license by Apple Inc ThinPrint is a trademark of Cortado AG in Germany and other countries All other brands and product names are registered trademarks or trademarks of their respective companies Thedesignations and will not be used in this Operation Guide License Agreements Typeface Trademark Acknowledgement All resident fonts in this printer are licensed from Monotype Imaging Inc Helvetica Palatino and Times are registered trademarks of L
54. oducts marketed in the United States Ozone concentration The printers generate ozone gas 03 which may concentrate in the place of installation and cause an unpleasant smell To minimize the concentration of ozone gas to less than 0 1 ppm we recommend you not to install the printer in a confined area where ventilation is blocked Safety Instructions Regarding the Disconnection of Power Caution The power plug is the main isolation device Other switches on the equipment are only functional switches and are not suitable for isolating the equipment from the power source VORSICHT Der Netzstecker ist die Hauptisoliervorrichtung Die anderen Schalter auf dem Ger t sind nur Funktionsschalter und k nnen nicht verwendet werden um den Stromflu im Ger t zu unterbrechen xiii xiv Canadian Department of Communications Compliance Statement This Class B digital apparatus complies with Canadian ICES 003 Avis de conformit aux normes du minist re des Communications du Canada Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada EN ISO 7779 Maschinenl rminformations Verordnung 3 GPSGV 06 01 2004 Der h chste Schalldruckpegel betr gt 70 dB A oder weniger gem EN ISO 7779 EK1 ITB 2000 Das Ger t ist nicht f r die Benutzung im unmittelbaren Gesichtsfeld am Bildschirmarbeitsplatz vorgesehen Um st rende Reflexionen am Bildschirmarbeitsplatz zu vermeiden darf dieses Produkt nicht
55. onditions such as ventilation may cause the machine to respond more slowly For more information about configuring settings refer to Sleep Timer Sleep timer timeout setting section of the Advanced Operation Guide Energy Saver Mode This mode reduces power consumption even more than quick recovery mode and allows Sleep mode to be set separately for each function To use the printer press GO The printer will be ready to operate within 24 seconds For more information on Energy Saver settings refer to Sleep Level Set Sleep level setting section of the Advanced Operation Guide Note If the Low Power Timer is equal to the Sleep Timer a Sleep mode is preceded Printing Operation Maintenance 3 Maintenance This chapter contains explanations on the following topics General Information Toner Container Replacement Replacing the Waste Toner Box Cleaning the Printer 3 2 3 2 3 6 3 8 3 1 General Information This chapter describes basic maintenance tasks you can perform on the printer You can replace the following component according to the printer s display Toner Kits Waste Toner Box Also the following parts need periodic cleaning Paper Transfer Unit Note Information Collection on Memory Chips The memory chip attached to the toner container is designed to improve convenience for the end user to support the recycling operation of empty toner containers and to gather informatio
56. ory error Press GO This message is displayed if the installed toner container s regional specification does not match the printer s Install the specified toner container An error has occurred in the USB memory device To return the printer to the print ready status press GO Use alternative Cassette 1 When the cassette does not contain any paper that matches the print data paper size and type this message allows you to specify an alternative cassette to use instead A paper source number is only displayed when an optional paper feeder is installed To print from a different paper source refer to Paper Feed Mode Setting the paper feed source section ofthe Advanced Operation Guide Wrong Account Displayed when an attempt is made to register an account in the Job Accounting menu by entering an account code that already exists For more information refer to Job Accounting Job Accounting selection setting section ofthe Advanced Operation Guide Wrong ID The ID or Password entered for the Job Accounting function is not correct Check the ID or Password For more information refer to Job Accounting Job Accounting selection setting section of the Advanced Operation Guide Wrong Password The password does not match the password set Enter the correct password For more information refer to Job Accounting Job Accounting selection setting section of the Adva
57. ot touch it with your hands as it may result in burn injury 1 Press the lever to release the lock 2 Pullthe front cover towards you 3 Ifthe paper has jammed near the registration roller as shown in A remove the paper by pulling it up from the center If the paper has jammed inside the fuser unit as shown in B open the fuser cover and remove the paper by pulling its edge 4 13 4 14 C If the paper has jammed inside the duplex unit as shown in C lift the duplex unit and remove the paper by holding it in the middle Duplex Unit 4 Close the front cover TFA HH i fe LL Paper Jam at Cassette 2 to 4 Paper is jammed at the paper cassette Remove the jammed paper using the procedure given below Pull out the paper feeder and remove the jammed paper Troubleshooting 5 Specifications 7 Note Specifications are subject to change without notice Item Description Printing Electrophotographic four color CMYK printing using tandem 4 drum system Method Printing Cassette A4 30 ppm B5 A5 A6 27 ppm Letter 32 ppm Legal 26 ppm ERGE MP Tray A4 27 ppm B5 A5 A6 27 ppmt Letter 28 ppm Legal 23 ppm Duplex Printing Speed A4 30 ppm B5 A5 27 ppmt Letter 32 ppm Legal 14 ppm Resolution 600 dpi First Print Out Time B W 8 5 seconds or less Color 10 seconds or less Warm up Time Power On 36 seconds or less 22 C 60 RH Sleep
58. ove the waste toner box as gently as possible so I as not to scatter the toner inside Do not let the opening of the waste toner box face downward 3 Close the cap to the old waste toner box after removing the box from the printer 4 To prevent toner from spilling put the old waste toner box in the plastic bag contained in the toner kit and discard it later according to the local code or regulations for waste disposal Maintenance Maintenance 5 Open the cap of the new waste toner box 6 Insert the new waste toner box as shown in the figure When the box is set correctly it will snap into place 7 Makesurethatthe waste toner box is correctly inserted and close the left cover After replacing the toner containers and the waste toner box clean the paper transfer unit For instructions refer to Cleaning the Printer on page 3 8 3 8 Cleaning the Printer The paper transfer unit should be cleaned each time the toner container and waste toner box are replaced To maintain optimum print quality it is also recommended that the inside of the printer be cleaned once a month as well as when the toner container is replaced It should also be cleaned if streaking or lines appear on printed copies or if printouts appear faint or blurred Cleaning the Paper Transfer Unit Print problems such as soiling of the reverse side of printed pages may occur if the paper transfer unit becomes dirty To clean the paper transfer
59. p even when printing is executed 2 Select an event to use with the text to speech function in Available events 3 Click Sound file Text to Speech column Click the browse button to notify the event by sound file Available events Events Sound file Text to Speech Cover open us Paper jam Add paper Sleep Add toner Toner low 9 Note The available file format is WAV When customizing the message texts to read on the screen aloud enter the texts in the text box Printing Operation Printing Operation Energy Saver Function Low Power Mode When the set time factory setting is 1 minute elapses after the printer is last used the printer automatically enters low power mode The message display backlight and lights turn off and power consumption is reduced This status is referred to as Low Power Mode The amount of time of no activity that must pass before Low Power Mode is activated may be lengthened For more information refer to Low Power Timer Low Power Mode timer timeout time section of the Advanced Operation Guide If print data is received during Low Power Mode the message display lights up and printing starts To resume press GO The printer will be ready to operate within 17 seconds Note that ambient environmental conditions such as ventilation may cause the machine to respond more slowly Sleep For Europe When the set time factory setting is 15 minutes elap
60. r container of any color always replace the waste toner box at the same time If this box is full the printer may be damaged or contaminated by the waste toner that may spill over the box CAUTION Do not attempt to incinerate parts which contain toner Dangerous sparks may cause burns IMPORTANT During toner container replacement temporarily move storage media and computer supplies such as floppy disks away from the toner container This is to avoid damaging media by the magnetism of toner IMPORTANT We are not liable against any damages or problems arising from the use of toner containers other than those designated as original our toner containers For optimum performance it is also recommended to use only the our toner containers which are specifically intended for use in your country or region If the toner container for another destination is installed the printer will stop printing Note You do not have to turn printer power off before starting the replacement Any data that may be processing in the printer will be deleted if you turn the printer power off To replace the toner container first make sure of the color of the toner container requiring replacement In this example it is assumed that you are replacing the yellow toner container 1 Open the top cover top tray Magenta M 2 Carefully remove the old toner container from the printer Maintenance 3 Putthe old toner container in the plast
61. radiators heaters or other heat sources or locations near flammable items to avoid the danger of fire To keep the printer cool and facilitate changing of parts and maintenance allow access space as shown below Leave adequate space especially around the side cover to allow air to be properly ventilated from the printer Top 400 mm 16 inches 40 Right 250 mm Rear 200 mm Front 600 mm 10 inches 7 7 8 inches 23 5 8 inches Other Precautions Adverse environmental conditions may affect the safe operation and performance of the printer Install in an air conditioned room recommended room temperature around 23 C humidity around 60 RH and avoid the following locations when selecting a site for the printer Avoid locations near a window or with exposure to direct sunlight Avoid locations with vibrations Avoid locations with drastic temperature fluctuations Avoid locations with direct exposure to hot or cold air Avoid poorly ventilated locations If the flooring is of a soft material it may be damaged by the casters when this product is moved after installation xvii xviii Power Supply Grounding the Printer WARNING Do not use a power supply with a voltage other than that specified Avoid multiple connections in the same outlet These types of situations present a danger of fire or electrical shock Plug the power cord securely into the outle
62. s displayed click Run setup exe If the user account management window appears click Yes Allow 2 Click View License Agreement and read the License Agreement Click Accept 3 Select Express Install tab Note To install Status Monitor it is necessary to install SJ Microsoft NET Framework 4 0 beforehand ee Setup has detected that the following prerequisites have not been met Microsoft NET Framework 4 0 www microsoft com Printing Operation Lenguas iii a Remove devices arwen and Driver Package Languac ge evel Ena Finished Your software is ready to use petails Product Detail Installed Status Monitor Installed FONTS Installed Uninstaller Installed a 2 8 Show Quick Print tab Printing Operation 4 Select the device to be installed You can also select Use host name for port name and setto use the host name ofthe standard TCP IP port AUSB connection cannot be used Note The machine cannot be detected unless it is on Ifthe SS computer fails to detect the machine verify that it is connected to the computer via a network or USB cable and that it is turned on and click Reload Select the package to be installed Packages include the following software Driver Package Prin
63. s within a document box O O Custom Box Job Box Settings Device Settings Configure the advanced settings of the machine O _ Paper Feed Output Energy Saver Timer Date Time System Function Configure the advanced function settings O BE Settings Common Job Defaults Printer E mail Network Settings Configure the network advanced settings O _ General TCP IP Protocol Security Settings Configure the security advanced settings O _ Device Security Network Security Certificates Management Configure the advanced management settings Settings Job Accounting Authentication Notification Report O History Settings SNMP Reset Printing Operation 2 5 Accessing Embedded Web Server RX 1 Launch your Web browser 2 Inthe address or location bar enter the machine s IP address or the host name Examples https 192 168 48 21 for IP address https P001 if the host name is P001 http 192 168 48 21 192 168 48 21 Admin Login le User Name Password Edo Status Login Device Information gt gt D Model Host Name Location a Home English v MAuto refresh USE Device Status amp b Printer Ready Status Message Sleeping Source Type Capacity Status Cassette1 A4 Pian 500 30 The web page displays basic information about the machine and Embedded Web Server RX as well as their current status Note Ifthe screen There is
64. ses after the printer is last used the printer automatically enters sleep mode The message display backlight and lights turn off to minimize power consumption This status is referred to as Sleep To use the printer press GO The printer will be ready to operate within 24 seconds For more information about configuring settings refer to Sleep Timer Sleep timer timeout setting section of the Advanced Operation Guide Except for Europe When the set time factory setting is 15 minutes elapses after the printer is last used the printer automatically enters sleep mode The message display backlight and lights turn off to minimize power consumption This status is referred to as Sleep For more information about configuring settings refer to Sleep Timer Sleep timer timeout setting section of the Advanced Operation Guide There are two sleep modes Quick Recovery and Energy Saver The default setting is Energy Saver mode Quick Recovery Mode The recovery from the sleep mode is faster than when using Energy Saver mode The message display goes off when sleep mode is entered and the Ready indicator flashes The machine recovers quickly when GO is pressed The machine also automatically recovers and prints when a job is detected If print data is received during Sleep the print job is performed while the message display remains unlit To use the printer press GO 2 27 2 28 Note that ambient environmental c
65. t If metallic objects come in contact with the prongs on the plug it may cause a fire or electric shock Always connect the printer to an outlet with a ground connection to avoid the danger of fire or electrical shock in case of an electric short If an earth connection is not possible contact your service representative Other Precautions Connect the power plug to the closest outlet possible to the printer Handling of Plastic Bags WARNING Keep the plastic bags that are used with the printer away from children The plastic may cling to their nose and mouth causing suffocation Precautions for Use Cautions when Using the Printer Do not place metallic objects or containers with water flower vases flower pots cups etc on or near the printer This type of situation presents a danger of fire or electrical shock should they fall inside Do not remove any of the covers from the printer as there is a danger of electrical shock from high voltage parts inside the printer Do not damage break or attempt to repair the power cord Do not place heavy objects on the cord pull it bend it unnecessarily or cause any other type of damage These types of situations present a danger of fire or electrical shock Never attempt to repair or disassemble the printer or its parts as there is a danger of fire electrical shock or damage to the laser If the laser beam escapes there is a danger of it causing blindness If the prin
66. ter becomes excessively hot smoke appears from the printer there is an odd smell or any other abnormal situation occurs there is a danger of fire or electrical shock Turn the power switch OFF O immediately remove the power plug from the outlet and contact your service representative If anything harmful paper clips water other fluids etc falls into the printer turn the power switch OFF O immediately Next remove the power plug from the outlet to avoid the danger of fire or electrical shock Then contact your service representative Do not remove or connect the power plug with wet hands as there is a danger of electrical shock Always contact your service representative for maintenance or repair of internal parts Do not pull the power cord when removing it from the outlet If the power cord is pulled the wires may become broken and there is a danger of fire or electrical shock Always grasp the power plug when removing the power cord from the outlet Always remove the power plug from the outlet when moving the printer If the power cord is damaged there is a danger of fire or electrical shock If the printer will not be used for a short period of time overnight etc turn the power switch OFF O If it will not be used for an extended period of time vacations etc remove the power plug from the outlet for safety purposes during the time the printer is not in use For safety purposes always remove t
67. ting System Driver Status Monitor Fonts Click Install Finish the installation When Your software is ready to use appears you can use the software To print a test page click the Print a test page checkbox and select the machine Click Finish to exit the wizard Note When you have selected Device settings in Windows amp XP the dialog box for device setting will appear after Finish is clicked Configure the settings for options installed on the machine Device settings can be configured after the installation is completed For details refer to the Device Settings in the Printing System Driver User Guide on the DVD ROM If a system restart message appears restart the computer by following the screen prompts This completes the printer driver installation procedure r ES Notice By using or installing the device drivers and software included in this package you agree to become bound by the terms and conditions of this license agreement View License Agreement C Dima Intl devices and utilities Move te items to tne proguats to insta st Devices Remove devices arvers and 2 16 Custom Install The following procedure is an example for installing the software in Windows 7 using Custom Install 1 Insert the DVD ROM Note Installation on Windows must be done by a user logged on with administrator
68. tion Guide Automatic 2 Sided Print Function This device includes 2 sided printing as a standard function For example by printing two 1 sided originals onto a single sheet of paper as a 2 sided print it is possible to lower the amount of paper used For more information refer to Duplex Duplex Printing section of the Advanced Operation Guide Printing in duplex mode reduces paper consumption and contributes to the conservation of forest resources Duplex mode also reduces the amount of paper that must be purchased and thereby reduces cost It is recommended that machines capable of duplex printing be set to use duplex mode by default Resource Saving Paper For the preservation and sustainable use of forest resources it is recommended that recycled as well as virgin paper certified under environmental stewardship initiatives or carrying recognised ecolabels which meet EN 12281 2002 or an equivalent quality standard be used This machine also supports printing on 64 g m paper Using such paper containing less raw materials can lead to further saving of forest resources 1 EN12281 2002 Printing and business paper Requirements for copy paper for dry toner imaging processes Your sales or service representative can provide information about recommended paper types Environmental benefits of Power Management To reduce power consumption when idle this machine is equipped with a power management function that automati
69. tions for current document only T Print data onl Default tray ly for Forms Use printer settings Auto Source Selection sette Multi Purpose Feeder Note For information on how to use the printer driver software amp refer to Printing System Driver User Guide 2 21 2 22 Printing by AirPrint AirPrint is a printing function that is included standard in iOS 4 2 and later products and Mac OS X 10 7 and later products This function enables you to connect and print to any AirPrint compatible device without installing a printer driver To allow the machine to be found when printing by AirPrint you can set machine location information in Embedded Web Server RX For details refer to the Embedded Web Server RX User Guide Printing Operation Printing Operation Status Monitor The Status Monitor monitors the printer status and provides an ongoing reporting function Note When you activate Status Monitor check the status below 5 Printing System Driver is Installed e Either Enhanced WSD or EnhancedWSD SSL are set to On in Security section of the Advanced Operation Guide Accessing the Status Monitor The Status Monitor also starts up when printing is started Exiting the Status Monitor Use either of the methods listed below to exit the Status Monitor e Exit manually Click the settings icon and select Exit in the menu to exit the Status Monitor Exit automatically The
70. try using a different type of paper replace the paper with paper from another ream flip the paper stack over or rotate the paper stack 180 degrees The printer may have problems if paper jams recur after the paper was replaced Whether or not the jammed pages are reproduced normally after printing is resumed depends on the location of the paper jam Utilizing Online Help Messages Online help messages are available in the printers message display to provide simple instructions for clearing jams Press J when the paper jam message has appeared Then a help message will appear to facilitate jam clearing in the location Paper jam at Cassette Paper is jammed at paper cassette 1 First open the printer s front cover and check for paper jams in the paper transfer unit For more information refer to Paper Jam in Printer on page 4 13 2 Pulloutthe paper cassette and remove the jammed paper Paper Jam at MP Tray Paper is jammed at the MP tray Remove the jammed paper using the procedure given below 1 First open the printer s front cover and check for paper jams in the paper transfer unit For more information refer to Paper Jam in Printer on page 4 13 2 Remove the jammed paper Troubleshooting Troubleshooting Paper Jam in Printer Paper is jammed at the paper cassette or inside the printer Remove the jammed paper using the procedure given below CAUTION Components inside the fuser cover are hot Do n
71. ult port 25 SMTP Server Set the amount of time to wait before time out in seconds Timeout Authentication Set whether SMTP authentication is used To use Protocol authentication enter the user information for authentication SMTP Security Set SMTP security Turn on SMTP Security in SMTP E mail TX on the Protocol Settings page POP before Specify the time in seconds until the connection to the POP SMTP Timeout server times outs This can be set when POP before SMTP is selected in Authentication Protocol Connection Test Tests to confirm that the settings are correct Domain Set whether or not domains are restricted Click the Domain Restriction List and enter the domain names of addresses to be allowed or rejected Restriction can also be specified by e mail address POP3 Set to receive e mail at the machine POP3 Protocol Set POP3 protocol Set the POP3 E mail RX setting to On on the Protocol Settings page Check Interval Specify the interval for checking for incoming e mail in minutes Run once now Click Receive to connect to the POP3 server immediately and check for incoming E mails Domain Set whether or not domains are restricted Click the Domain Restriction List and enter the domain names of addresses to be allowed or rejected Restriction can also be specified by e mail address POP3 User Configure the settings for POP3 user accounts and the POP3 Settings server You can configure up to three users
72. under the terms of GPL LGPL Open SSLeay License Copyright 1998 2006 The OpenSSL Project All rights reserved Redistribution and use in source and binary forms with or without modification are permitted provided that the following conditions are met 1 Redistributions of source code must retain the above copyright notice this list of conditions and the following disclaimer Redistributions in binary form must reproduce the above copyright notice this list of conditions and the following disclaimer in the documentation and or other materials provided with the distribution vii viii 3 All advertising materials mentioning features or use of this software must display the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http www openssl org 4 The names OpenSSL Toolkit and OpenSSL Project must not be used to endorse or promote products derived from this software without prior written permission For written permission please contact openssl core openssl org 5 Products derived from this software may not be called OpenSSL nor may OpenSSL appear in their names without prior written permission of the OpenSSL Project 6 Redistributions of any form whatsoever must retain the following acknowledgment This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit http www openssl org THIS SOFTWARE
73. urn the printer to the print ready status press GO Add paper MPTray The paper has run out in the paper source displayed Supply paper according to the paper source displayed paper cassettes MP tray or optional paper feeders This message is displayed alternately with messages indicating the printer status such as Ready Please wait and Processing Call service F Call service 0123456 F represents a controller error 0 1 2 Call for service The printer does not operate when this message is displayed represents a mechanical error 0 1 2 Call for service The printer does not operate when this message is displayed The total number of pages printed is also indicated e g 0123456 Canceling data Displayed when data is being canceled Cassette not loaded The corresponding paper cassette is not installed Install the cassette The cassette number can be 1 topmost to 4 bottom Change envelope switch position Check cassette Displayed when the paper type does not match the envelope switch setting This message is displayed when a paper lift error has occurred in the paper source s cassette Pull out the cassette for the paper source displayed either the paper cassettes or optional paper feeders and check if the paper is loaded correctly The message Call service is displayed when this error occurs repeatedl
74. y Check waste toner box This message warns following two cases Install the new waste toner box The waste toner box is not installed The waste toner box is full Close front cover The front cover of the printer is open Close the front cover Close left cover Close top cover The left cover of the printer is open Close the left cover The top cover of the printer is open Close the printer top cover Troubleshooting Message Corrective Action Device busy This message is displayed when Remove Device was selected while a USB memory was being used The previous screen is displayed again 1 or 2 seconds Duplex disabled Press GO You attempted to print with a paper size and paper type that cannot be used for duplex printing Press GO to print onto one side of the paper only Enter Account An account code must be entered This message is displayed if you try to print from the operation panel e g printing a status page or using the Job Retention function when the Job Accounting function is enabled For more information refer to Job Accounting Job Accounting selection setting section of the Advanced Operation Guide Envelope mode Displayed when the envelope switch is set to envelope mode Error Power off F Turn the power switch off and then back on again Ifthis message still remains turn the power switc
75. y turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help The use of a non shielded interface cable with the referenced device is prohibited CAUTION The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with Part 15 of FCC Rules and RSS Gen of IC Rules Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device The above warning is valid only in the United States of America Interface connectors IMPORTANT Be sure to power off the printer before connecting or disconnecting an interface cable For protection against static electricity discharge to the printer s internal electronics through the interface connector s cover any interface connector that is not in use with the protective cap supplied l Note Use shielded interface cables Safety Information Laser Safety This pr

Download Pdf Manuals

image

Related Search

Related Contents

Guidelines for Client Managers  Service Manual - Wiki Karat  Dokumentation von Zibepla FeWo 2.1.0 Deutsch  User Manual - ProductReview.com.au  Samsung Samsung C3780 Korisničko uputstvo  株式量社アクティオ 殿 - 【AKTIO】アクティオエンジニアリング事業部  Nikon Zoom Wide Angle-Tele 28-70mm f/2.8 D-AFS AF Lens - AF-S_28  User Manual - File Management  iSPOT 575 EB  MSA Optimair HC (Health Care) User Manual  

Copyright © All rights reserved.
Failed to retrieve file