Powerplus POWXQ5234 cordless combi drill
Contents
1. Do not overreach Keep proper footing and balance at all times This enables better control of the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from moving parts Loose clothes jewellery or long hair can be caught in moving parts f devices are provided for the connection of dust extraction and collection facilities ensure these are connected and properly used Use of these devices can reduce dust related hazards 5 4 Power tool use and care Do not force the power tool Use the correct power tool for your application The correct power tool will do the job better and safer at the rate for which it was designed Do not use the power tool if the switch does not turn it on and off Any power tool that cannot be controlled with the switch is dangerous and must be repaired Disconnect the plug from the power source before making any adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool Power tools are dangerous in the hands of untrained users Maintain power tools Check for misalignment or sticking of moving parts breakage of parts and any other condition that may affect the power tool s operat2. ROWERPLUS XQ POWXQ5234 EN Do not abuse the cord Never use the cord for carrying pulling or unplugging the power tool Keep cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of electric shock When operating a power tool outdoors use an extension cord suitable for outdoor use Use of a cord suitable for outdoor use reduces the risk of electric shock f operating a power tool in a damp location is unavoidable use a residual current device RCD protected supply Use of an RCD reduces the risk of electric shock 5 3 Personal safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool while you are tired or under the influence of drugs alcohol or medication A moment of inattention while operating power tools may result in serious personal injury Use safety equipment Always wear eye protection Safety equipment such as dust mask non skid safety shoes hard hat or hearing protection used whenever conditions require will reduce personal injuries Avoid accidental starting Ensure the switch is in the off position before plugging in Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents Remove any adjusting key or wrench before turning the power tool on A wrench or a key left attached to a rotating part of the power tool may result in personal injury
3. 4 a Philippe Vankerkhove Certification Manager Date 17 01 2012 Copyright 2012 VARO NV Page 13 www varo com
4. the chuck jaws Insert drill bit straight into chuck the full length of the jaws as shown in Tighten the chuck jaws on the drill bit WARNING Make sure to insert drill bit straight into chuck jaws Do not insert drill bit into chuck jaws at an angle this could cause drill bit to be thrown from drill resulting in possible serious personal injury or damage to the chuck 9 4 2 Removing bits Lock the switch trigger by placing rotation selector in centre position Loosen the chuck jaws from the drill bit Do not use a wrench to tighten or loosen the chuck jaws Remove the drill bit from the chuck jaws 9 5 Adjustable torque This drill is equipped with an adjustable torque for driving different types of screws into different materials The proper setting depends on the type of material and the size of screw you are using TO ADJUST TORQUE Identify the 25 position torque ring located on the front of the drill Rotate adjusting ring 2 to the desired setting 21 25 ef a For heavy drilling LL For hammer drilling 10 DRILLING 10 1 Drilling hard smooth surfaces When drilling hard smooth surfaces use a centre punch to mark desired hole location This will prevent the drill bit from slipping off centre as the hole is started However the low speed feature allows starting holes without centre punching if desired To accomplish this simply operate the drill at a low speed until the hole is started The material to be drilled should
5. 1 www varo com POWERPLUS XQ POWXQ5234 EN 10 1 Drilling hard smooth surfaCceS sssssaaassnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 9 WO Wood GNUNG E 10 TOS AMIGTAl e e E 10 104 Masonry CIN sos ate sais se Sac sans ean a ann eas pened ee emi ene ee 10 11 CLEANING AND MAINTENANCE 00 eet teeeeeeeeeeeeneeeeeneeeeeneees 10 8 fy E amp 7 1 Le E 10 TL2 et e 10 11 3 Connecting Cable ANd MAINS plug cccccssseseecsnecesneensenseensnnnssssseneaansnessseaaenenes 10 12 TEE 10 13 TECHNICAL DATA uoaa este wcaseienawacnescusanesceeceeueaeces 11 14 SOUND EMISSION E 11 9 WARRANTY oee eeitemeueccncnenecveucenscocannedeiaxcwarsmencaneses 11 16 SCT er E WR 12 16 1 lt BQUCIY DA CK EE 12 17 DECLARATION OF CONFORMITY cccccceeseesceenseeseenneeees 13 Copyright 2012 VARO NV Page 2 www varo com PowerpLus X J POWXQ5234 EN POWXQ5234 CORDLESS DRILL 18V 1 APPLICATION The power tool is intended for driving and drilling through wood metal plastics and masonry It is not designed for commercial use before using the appliance for your own safety Your power tool should only be passed on together with these instructions D WARNING Read this manual and general safety instructions carefully 2 DESCRIPTION FIG A Keyless chuck Torque adjustment ring Speed selector switch knob On off switch Battery pack Auxiliary handle Forward reverse knob Screw bits Batt
6. be secured in a vise or with clamps to keep it from turning as the drill bit rotates Hold tool firmly and place the bit at the point to be drilled Move the drill bit into the work piece applying only enough pressure to keep the bit cutting Do not force or apply side pressure to elongate a hole WARNING Be prepared for binding or bit breakthrough When these situations occur drill has a tendency to grab and kick opposite to the direction of rotation and could cause loss of control when breaking through material If not prepared this loss of control can result in possible serious injury If the bit jams in work piece or the drill stalls release switch trigger immediately Remove the bit from the work piece and determine the reason for jamming Copyright 2012 VARO NV Page 9 www varo com POWERPLUS XQ POWXQ5234 EN 10 2 Wood drilling For maximum performance use high speed steel bits for wood drilling Turn the torque adjustment ring on the drill to desired torque setting Begin drilling at a very low speed to prevent the bit from slipping off the starting point Increase the speed as the drill bit bites into the material When drilling through holes place a block of wood behind the workpiece to prevent ragged or shintered edges on the back side of the hole 10 3 Metal drilling For maximum performance use high speed steel bits for metal or steel drilling Turn the torque adjustment ring on the drill to desired torque setting Begin dr
7. proper machine care and regular cleaning 11 3 Connecting cable and mains plug If the connecting cable or mains plug is damaged it must be replaced Replacement of the connecting cable should only be carried out by a qualified specialist qualified electrician 12 STORAGE Store it out of the reach of children in a stable and secure position in a cool and dry place avoid too high and too low temperatures Battery storage Store and charge your batteries in cool area Temperatures below 10 C 50 F or above 38 C 100 F will shorten battery life Copyright 2012 VARO NV Page 10 www varo com POWERPLUS XQ POWXQ5234 EN Never store batteries in discharged condition Recharge them immediately after they are discharged Batteries gradually lose their charge the higher the temperature the quicker so If you store your tool for longer periods of time without using it recharge the batteries every month or two This will prolong battery life 13 TECHNICAL DATA Model No POWXQ5234 Chuck 13 mm keyless Power supply 18 Volt DC Gear Train 2 Speed No oet cpet 0 470 0 1800 min Clutch 25 Positions Charger input 230 V 50 Hz Charger Rate 1 hour Torque 40 Nm MAX Battery Pack Model POWXQ5234B Battery Type NiMh Battery capacity 2500 mAh 14 SOUND EMISSION Noise emission values measured according to relevant standard K 3 POWXQ5234 LpA Sound pressure level 86 dB A LwA Sound power level 97 dB A
8. 1 APPEICSA THON HE 3 2 DESCRIPTION FIG A E 3 3 PACKAGE CONTENTS LIST ccccssseeecesseeeccesseeseesseeseenseessoees 3 4 eS E 4 5 GENERAL POWER TOOL SAFETY VWARNINGS seess 4 5 1 Work aroa isossa ronio S 4 9 2 Electrical Eegeregie eege 4 5 3 POISONAl Salo eessen 5 5 4 Pwer 100 USC and Car EE 5 5 5 IOI e AEI EI A NT N T N E T P A A A 6 ADDITIONAL SAFETY INSTRUCTIONS n sssnnannnnnnnnnnnnnnnnnnnnnnnnnnnnnne 6 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGER Sanr E E 6 8 FEATURES ear ee nse eee saci ssk sewer ee ce auc ae eawueewnaeceveceuedacewe 7 8 1 K yl ss CHUCK 1 siciiccasedawnewsacrsntnieonsdceanenandatnanesexdnensnduoasssaseeieaendateonsdansnenandeenodeaaadecn 7 8 2 TOPQUG AO USUMENT WAG 2 easscnssteseseeacescateataratenndaeashantenaueadeeashencaunaneacddeacteasamaneesdaeadhs 7 8 3 Forward reverse selector right left rotation selector 7 c sscccneseccnnnenennnenennecnanens 7 8 4 Vanapa Speed H 7 8 5 Speed SCIOCION J EE 7 9 PREJ OPERATION EE 7 9 1 Charging the battery DaCK accra A E 7 9 2 Install remove DatZet Dereke teggegesgegegugegeggesgegeg geed dE 8 9 2 1 To install battery pack on your cordless dl 8 9 22 TOrem ve battery e 8 9 3 SL E y E 8 TaN VU Wee 8 GE Direciono TOLANON REER OEEO TENERA 8 933 Ee persse E EEE SEEE E 8 9 4 installing removing Dils sssri EAEE raaa 9 GE e HR e Ell Lee siai EEEa 9 GEN tele e ko E 9 9 5 PIQIUSTADIC ee E 9 MO ING E 9 Copyright 2012 VARO NV Page
9. The machine may exceed 85 dB A at the workplace In this case noise protection measures need to be introduced to protect the user POWXQ5234 Vibration aw 6 07 m s K 1 5 m s 15 WARRANTY This product is warranted for a 5 year period effective from the date of purchase by the first user This warranty covers all material or production flaws It does not include defective parts subject to normal wear amp tear such as bearings brushes cables and plugs or accessories such as drills drill bits saw blades etc damage or defects resulting from maltreatment accidents or alterations nor the cost of transportation This warranty covers all material or production flaws excluding batteries chargers defective parts subject to normal wear and tear such as in particular bearings brushes cables plugs Accessories such as drills drill bits saw blades etc also do not fall under this warranty Damage and or defects resulting from inappropriate use also do not fall under the warranty provisions We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool Repairs may only be carried out by an authorised customer service centre for Powerplus tools Copyright 2012 VARO NV Page 11 www varo com POWERPLUS XQ POWXQ5234 EN You can always obtain more information at the number 00 32 3 292 92 90 Any transportation costs shall always be borne by the customer unless ag
10. e drill is started and stopped by depressing and releasing the switch trigger Release the switch trigger to turn the drill OFF in short time because of electric brake 9 3 1 Switch lock The switch trigger can be locked in the OFF position This helps to reduce the possibility of accidental starting when not in use To lock the switch trigger place the direction of rotation selector in the center position 9 3 2 Direction of rotation The direction of rotation is controlled by the direction of rotation selector located above the switch trigger With the drill held in normal operating position the direction of rotation selector should be positioned to the left of the switch for drilling The rotation direction is reversed when the selector is to the right of the switch When the selector is in the center position the switch trigger is locked 9 3 3 Variable speed This tool has a variable speed switch that delivers higher speed and torque with increased trigger pressure Speed is controlled by the amount of switch trigger depression Copyright 2012 VARO NV Page 8 www varo com POWERPLUS XQ POWXQ5234 EN 9 4 Installing removing bits 9 4 1 Installing bits Lock the switch trigger by placing the direction of rotation selector in centre position Open or close chuck jaws to a point where the opening is slightly larger than the bit size you intend to use Also raise the front of the drill slightly to keep the bit from falling out of
11. ery pack release button 3 PACKAGE CONTENTS LIST Remove all packing materials Remove remaining packaging and transit supports if existing Check the completeness of the packing content Check the appliance the power cord the power plug and all accessories for transportation damages Keep the packaging materials as far as possible till the end of the warranty period Dispose it into your local waste disposal system afterwards i 2 3 4 5 6 I 8 9 WARNING Packing materials are no toys Children must not play with plastic bags Danger of suffocation Cordless impact drill 3pcs screw bits 1pc on cordless drill 2pcs battery 1 mounted 1pc charger 1pc auxiliary handle on cordless drill Instruction manual K 6 i When parts are missing or damaged please contact your dealer Copyright 2012 VARO NV Page 3 www varo com POWERPLUS XQ POWXQ5234 EN 4 SYMBOLS The following symbols are used in this manual and or on the machine Denotes risk of personal injury loss of life or damage to the tool in case of AN non observance of the instructions in this manual Warning to reduce the risk of injury user must read instruction manual A e Conforms to all regulatory standards in the country EU where the product is purchased Always wear hearing protection with impact drills Exposure to noise can cause hearing loss X Do not expose charger and battery pack to water
12. illing at a very low speed to prevent the bit from slipping off the starting point Maintain a speed and pressure which allows cutting without overheating the bit Applying too much pressure will Overheat the drill Wear the bearings Bend or burn bits Produce off center or irregular shaped holes When drilling large holes in metal it is recommended that you drill with a small bit at first then finish with a large bit Also lubricate the bit with oil to improve drilling action and increase bit life 10 4 Masonry drilling For maximum performance use carbide tipped masonry impact bits when drilling holes in brick tile etc Rotate the torque selector to impact position T Apply light pressure and medium speed for best results in brick When drilling holes in tile practice on a scrap piece to determine the best speed and pressure 11 CLEANING AND MAINTENANCE 11 1 Cleaning Keep the ventilation slots of the machine clean to prevent overheating of the engine Regularly clean the machine housing with a soft cloth preferably after each use Keep the ventilation slots free from dust and dirt If the dirt does not come off use a soft cloth moistened with soapy water Never use solvents such as petrol alcohol ammonia water etc These solvents may damage the plastic parts 11 2 Maintenance Our machines have been designed to operate over a long period of time with a minimum of maintenance Continuous satisfactory operation depends upon
13. ion If damaged have the power tool repaired before use Many accidents are caused by poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to stick and are easier to control Use the power tool accessories and tool bits etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work to be performed Use of the power tool for operations different from intended could lead to a hazardous situation Copyright 2012 VARO NV Page 5 www varo com POWERPLUS XQ POWXQ5234 EN 5 5 Service Have your power tool serviced by a qualified repair person using only identical replacement parts This will ensure that the safety of the power tool is maintained 6 ADDITIONAL SAFETY INSTRUCTIONS Always wear hearing protection with impact drills Exposure to noise can cause hearing loss Use auxiliary handle s if supplied with the tool Loss of control can cause personal injury Hold power tool by insulated gripping surfaces when performing an operation where the cutting accessory may contact hidden wiring or its own cord Cutting accessory contacting a live wire may make exposed metal parts of the power tool live and could give the operator an electric shock 7 ADDITIONAL SAFETY INSTRUCTIONS FOR BATTERIES AND CHARGERS Batteries 1 Never attempt
14. l SCH f 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and all instructions Failure to follow all warnings and instructions may result in electric shock fire and or serious injury Save all warnings and instructions for future reference The term power tool in the warnings refers to your mains operated corded power tool or battery operated cordless power tool 5 1 Work area Keep work area clean and well lit Cluttered and dark areas invite accidents Do not operate power tools in explosive atmospheres such as in the presence of flammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep children and bystanders away while operating a power tool Distractions can cause you to lose control 5 2 Electrical safety Always check that the power supply corresponds to the voltage on the rating plate Power tool plugs must match the outlet Never modify the plug in any way Do not use any adapter plugs with earthed grounded power tools Unmodified plugs and matching outlets will reduce risk of electric shock Avoid body contact with earthed or grounded surfaces such as pipes radiators ranges and refrigerators There is an increased risk of electric shock if your body is earthed or grounded Do not expose power tools to rain or wet conditions Water entering a power tool will increase the risk of electric shock Copyright 2012 VARO NV Page 4 www varo com
15. nd torque will in decrease equivalently to applied trigger pressure This drill has an electric brake when the trigger switch is released the chuck stops turning 8 5 Speed selector 3 Your cordless drill has a two speed gear designed for drilling or driving at LO Low or HI High speed A slide switch is located on top of your drill to select either LO Low or HI High speed 9 PRE OPERATION WARNING Do not allow familiarity with the drill make you careless One careless fraction of a second is sufficient to inflict severe injury 9 1 Charging the battery pack The battery pack for this tool is supplied in a low charge condition to prevent possible problems therefore you have to charge the battery before first use Note The battery will not reach full charge after the first charge Allow several cycles drilling followed by recharging for them to become fully charged TO CHARGE f Charge battery pack solely with the charger provided Make sure that the power supply is 230 Volts AC 50Hz Connect the charger to the power supply Attach the battery pack 5 to the charger by aligning the ribs on battery pack 5 with grooves on the charger then slide battery pack 5 into the charger The red light is flickering now When the battery is fully charged the red light goes off and the green light goes on The battery pack will become slightly warm while charging This is normal and does not indicate a problem A forced ve
16. ntilation helps to cool down the charger Do not place charger in an area of extreme heat or cold It will work best at normal room Copyright 2012 VARO NV Page 7 www varo com ROWERPLUS XQ POWXQ5234 EN temperature When the battery is fully charged unplug your charger from the power supply and remove the battery pack from the charger CAUTION To prevent damage to the battery pack remove the battery pack immediately from the charger when no LED illuminates Return battery pack and charger to your dealer for checking or replacing Do not insert a battery pack into a damaged charger it may damage your battery pack 9 2 Install remove battery pack 9 2 1 To install battery pack on your cordless drill Lock the switch trigger 4 on the drill by placing the forward reverse selector in its centre position Place the battery pack in the drill Align the raised rib on battery pack with the groove inside the drill Make sure the latches on each side of your battery pack snap in place and battery pack is secured in the drill before beginning operation 9 2 2 To remove battery pack Lock the switch trigger on the drill by placing the forward reverse selector in its centre position Locate latches 9 on the side of the battery pack and depress them to release the battery pack from the drill The battery pack will automatically disconnect in the direction it should be removed in Remove the battery pack from you drill 9 3 Switch Th
17. nvironmentally safe way C A Waste of electrical products should not be disposed of with household waste Please recycle where facilities exist Check with your Local Authority or Me etailer for recycling advice 16 1 Battery pack This product contains nickel metal hydride To preserve natural resources please recycle or dispose of batteries properly Local state or federal laws may prohibit disposal of nickel metal hydride batteries in ordinary trash Consult you local waste authority for information regarding available recycling and or disposal options Copyright 2012 VARO NV Page 12 www varo com ROWERPLUS XQ POWXQ5234 EN 17 DECLARATION OF CONFORMITY CE VARO N V Joseph Van Instraat 9 BE2500 Lier BELGIUM declares that Product Cordless Impact Drill 18V Trade mark POWERplus XQ Model POWXQ5234 Is in conformity with the essential requirements and other relevant provisions of the applicable European Directives based on the application of European harmonized standards Any unauthorized modification of the apparatus voids this declaration European Directives including if applicable their amending directives 2004 108 EC 2006 42 EC European harmonized standards including if applicable their amendments EN60745 1 2009 EN60745 2 1 2010 EN60745 2 2 2010 EN55014 1 2006 EN55014 2 1997 The undersigned acts on behalf and under the power of attorney of the company management S ww
18. reed otherwise in writing Atthe same time no claim can be made on the warranty if the damage of the device is the result of negligent maintenance or overload Definitely excluded from the warranty is damage resulting from fluid permeation excessive dust penetration intentional damage on purpose or by gross carelessness inappropriate usage use for purposes for which the device is not suitable incompetent usage e g not following the instructions given in the manual inexpert assembly lightning strike erroneus net voltage This list is not exhaustive Acceptance of claims under warranty can never lead to the prolongation of the warranty period nor commencement of a new warranty period in case of a device replacement Devices or parts which are replaced under the warranty therefore remain the property of Varo NV We reserve the right to reject a claim whenever the purchase cannot be verified or when it is clear that the product has not been properly maintained Clean ventilation slots carbon brushes serviced regularly etc Your purchase receipt must be kept as proof of date of purchase Your appliance must be returned undismantled to your dealer in an acceptably clean state in its original blow moulded case if applicable to the unit accompanied by proof of purchase 16 ENVIRONMENT D Should your appliance need replacement after extended use do not dispose ST of it with the household refuse but in an e
19. the tool only to charge the battery Never attempt to charge non rechargeable batteries Have defective cords replaced immediately Do not expose to water Do not open the charger Do not probe the charger The charger is intended for indoor use only oe SS mg Copyright 2012 VARO NV Page 6 www varo com POWERPLUS XQ POWXQ5234 EN 8 FEATURES 8 1 Keyless chuck 1 Your drill has a keyless chuck that allows you to hand tighten or release drill bit in the chuck jaws 8 2 Torque adjustment ring 2 The drill has a torque adjustment ring It allows you to select the desired torque depending on the task you have to perform drill different types of screws into different materials The proper setting depends on the type of material and the size of screw you are using 8 3 Forward reverse selector right left rotation selector 7 The drill has a forward reverse selector located above the switch trigger Press selector F orward R everse on left side of machine to the right side drill turns left reverse loosen screws Press selector F orward R everse on right side to the left side drill turns right forward fasten screws CAUTION To prevent damage to the gearbox always allow the chuck to come to a complete stop before changing the direction of rotation or selecting another speed HI LO To stop release the trigger switch 8 4 Variable speed 4 Your cordless drill has a variable speed switch The rotational speed a
20. to open for any reason 2 Do not store in locations where the temperature may exceed 40 C 3 Charge only at ambient temperatures between 10 C and 40 C 4 Charge only using the charger provided with the tool 5 When disposing of batteries follow the instructions given in the section Protecting the environment Do not cause short circuits If connection is made between the positive and A negative terminal directly or via accidental contact with metallic objects the D battery is short circuited and an intense current will flow causing heat generation which may lead to casing rupture or fire 7 Donot heat If batteries are heated to above 100 C sealing and insulating separators and other polymer components may be damaged resulting in electrolyte leakage and or internal short circuiting leading to heat generation causing rupture or file Moreover do not dispose of the batteries in fire explosion and or intense burning may result 8 Under extreme conditions battery leakage may occur When you notice liquid on the battery proceed as follows Carefully wipe the liquid off using a cloth Avoid skin contact In case of skin or eye contact follow the instructions below i Immediately rinse with water Neutralize with a mild acid such as lemon juice or vinegar ll In case of eye contact rinse abundantly with clean water for at least 10 minutes Consult a physician Chargers Use the charger provided with
Download Pdf Manuals
Related Search