Gefen GTV-WHD-1080P-SR-EU
Contents
1. HOM 1080P PROGRESSIVE Wireless for HDMI In Room Solution GTV WHD 1080P SR User Manual gefentv com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM Monday through Friday Pacific Time Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefentv com support gefentv com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice Wireless for HDMI In Room Solution is a trademark of Gefen LLC 2014 Gefen LLC All rights reserved All trademarks are the property of their respective owners Rev A5 CONTENTS 1 Introduction 2 FCC Statement 3 Operation Notes 5 Features 6 Panel Layout 6 Sender Unit 7 Receiver Unit 8 Panel Descriptions 8 Sender Unit 8 Receiver Unit 9 IR Remote Control Unit 9 Layout and Descriptions 10 Connecting the Wireless for HDMI 10 Wiring Diagram 11 Operating the Wireless for HDMI 11 The Linking Process 12 Using Multiple Sender Units 12 Adding a New Video Source 15 Renaming Sources 18 Switching between Sources 20 Deleting Sources 24 Disconnecting the Wireless Link 25 Recomnecting the Wireless Link 26 Power Down Mode 27 Powering Up after a Power Down 28 Specifications 29 Warranty INTRODUCTION Congratulations on your purchase of th2. be displayed Connected to Sender TIP Use the INPUT DEVICES buttons see page 9 on the IR Remote Control to bypass the Select Video Source menu and directly switch to another Sender unit 19 OPERATING THE WIRELESS FOR HDMI Deleting Sources If a Sender unit source will no longer be necessary it can be removed from the Wireless for HDMI network 1 Point the IR Remote Control at the Receiver unit and press the MENU button Setup P Add new Video Source gt Remove Video Source gt Modify Video Source Name gt Disconnect Wireless Link 2 Select Remove Video Source from the Setup menu using the cursor buttons on the IR Remote Control Setup gt Add new Video Source gt Remove Video Source amp Modify Video Source Name Disconnect Wireless Link ui 20 OPERATING THE WIRELESS FOR HDMI 3 Click the OK button to confirm the selection 4 The Chose Source to Remote menu will be displayed 5 Select the source to be removed and press the OK button Choose Source to Remove gt STB gt DVR 6 Press the OK button to confirm the removal of the selected device Removing BluRay Press OK to continue or Exit to cancel 7 After a few seconds the screen will go blank 21 OPERATING THE WIRELESS FOR HDMI 8 Press the SOURCE button to display the Select Video Source menu Select Video Source gt DVR gt Setup 9 Select the de
3. B jack can also use powered USB port Power Supply RECEIVE cion 1 SV 2ADC Power Consumption Sender Receiver 3W max 8W max Dimensions W x H x D Sender 1 2 x 0 6 x 3 9 29mm x 14 5mm x 98mm Dimensions W x H x D Receiver 5 83 x 0 8 x 3 8 148mm x 20mm x 96mm Shipping Weight ossessi ads 2 0 Ibs 0 9 kg All features and specifications are subject to change without notice 28 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables a
4. Connecting to message will be displayed Connecting to DVR 2 After a few seconds the wireless link will be restored and the source signal will be displayed 25 OPERATING THE WIRELESS FOR HDMI Power Down Mode The Wireless for HDMI can be powered down when not in use 1 Point the IR Remote Control at the Receiver unit and press the GUEST button 2 After a few seconds the screen Receiver and Sender unit s will power down A status message indicating that the Wireless for HDMI has been powered down will be displayed Powering Down 26 OPERATING THE WIRELESS FOR HDMI 3 After the Wireless for HDMI has been successfully powered down the Wireless Off message will be displayed on the screen Wireless Off Powering Up after a Power Down 1 Point the IR Remote Control at the Receiver unit and press the GUEST button 2 The Connecting to message will be displayed 3 After afew moments the selected source signal will be restored e Connected to DVR 27 SPECIFICATIONS Operating Frequency india aia iad 5 GHz Supported resolutiOnS anime 480p to 1080p Video Input Connector Sende ococonooncccinnoccncnos 1 HDMI Type A 19 pin male Video Output Connector Receiver 1 HDMI Type A 19 pin female USB Connector Sender Receiver 1 Mini B Receiver factory use only Power Supply Sender iun uandspsdmeinannesrinn 1 5V 1A DC with US
5. DMI cable devices O NOTE The Wireless for HDMI In Room Solution does not support DVI Connect the included USB to Mini USB cable from a USB port on the computer to the Mini B connector on the Sender unit If the source does not have a powered USB port connect the included mini USB to USB cable to the Sender and to the included USB power supply Connect this power supply to an available electrical outlet Connect the included 5V DC power supply to the Receiver unit and connect the power supply to an available electrical outlet The Link and Video LED indicators on both the Sender and Receiver unit will glow bright blue to indicate a successful connection between the Sender and Receiver unit Ordinarily no pairing is required out of the box However the Sender and Receiver can also be paired manually if needed Wiring Diagram for the Wireless for HDMI In Room Solution Gefen HDMI CABLE USB POWER Ml 10 OPERATING THE WIRELESS FOR HDMI The Linking Process After all the connections have made see page 10 to the Wireless for HDMI the Receiver unit will attempt to negotiate with the Sender unit Status Message Provides information on the current status of the Wireless for HDMI Connecting to Sender After a few moments the source signal will appear on the display The status message will disappear after a few seconds Connected to Sender 11 OPERATING THE WIRELESS FOR HDMI Using Mult
6. e GefenTV Wireless for HDMI Your complete satis faction is very important to us About Gefen We specialize in total integration for your home theater while also focusing on going above and beyond customer expectations to ensure you get the most from your hardware We invite you to explore our distinct product line Please visit http www gefen com for the latest offerings in High Definition signal solutions or call us between the hours of 8 00 am and 5 00 pm Monday Friday Pacific Standard Time for assistance with your A V needs We ll be happy to assist you The GefenTV Wireless for HDMI In Room Solution The GefenTV Wireless for HDMI In Room Solution sends high definition audio and video to any HDTV display up to 80 feet 25 meters It extends HDMI A V content from computers using HDMI set top boxes Blu ray players and other A V sources to remote HDMI compliant display s This wireless product is comprised of a small Sender unit and one table top Receiver unit It supports HD resolutions up to 1080p Full HD along with support for up to 7 1 channels of LPCM and up to 5 1 channels of Dolby TrueHD and DTS HD Master Audio The Wireless for HDMI In Room Solution transmits within the room and does not require line of sight placement of transceivers for good reception Thanks to its small form factor and easy to plug in Sender unit this product is ideal for high definition A V extension within a conference room or home theater installati
7. e below The first character first row first column is a space and can be used anywhere in the name The maximum length of the Source name cannot exceed nine characters including any spaces Figure 2 Available characters for source naming Rename Video Source Name lender Use the lt and cursor keys to select the character in the name to be changed 16 OPERATING THE WIRELESS FOR HDMI 4 After the video source has been renamed press the OK button to save the changes Select Video Source gt Sender gt Setup 17 OPERATING THE WIRELESS FOR HDMI Switching between Sources Once two or more Sender units have been connected to a Receiver unit use the IR Remote Control unit to switch between each source 1 Point the IR Remote Control at the Receiver unit and press the Source button The Select Video Source menu will be displayed Select Video Source gt STB gt BluRay 2 Use the Cursor buttons on the IR Remote Control to select the desired source Select Video Source gt STB gt Setup 18 OPERATING THE WIRELESS FOR HDMI 3 Once the desired source has been selected press the OK button Select Video Source 4 The screen will go blank momentarily and the Connecting to status message will be displayed indicating that the Receiver unit is switching to the selected Sender unit source 5 After a few moments the selected source signal will
8. ent from that to which the Receiver unit is connected e Consult the dealer or an experienced radio TV technician for help In order to maintain compliance with FCC regulations shielded cables must be used with this equipment Operation with non approved equipment or unshielded cables is likely to result in interference to radio and TV reception The user is cautioned that changes and modifications made to the equipment without the approval of the manufacturer could void the user s authority to operate this equipment OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE GEFENTV WIRELESS FOR HDMI IN ROOM SOLUTION Maximum extension distance is 80 feet 25 meters with a clear line of sight Supported resolutions 1080p60 1080p50 1080p24 1080i60 1080i50 720p60 720p50 576p50 576150 480p60 480i60 VESA 1600x1200 1366x768 1280x1024 1024x768 800x600 640x480 Obstructions such as walls and furniture may reduce performance and reception distance DVI D Support Gefen recommends placing both units into the provided stands with the Gefen logo pointing down to help maintain the strongest possible transmission signal Interference caused by other RF products may reduce performance and reception distance Use with multiple Sender units Can be used with a single Receiver unit to provide source switching capability Up to 8 Senders are supported Local RF interference can limit the n
9. ional Limitations Regarding US and EU models note that all RF devices are designed by compliance regulation to accept interference from all other devices Operation of wireless products is therefore dependent on the environment they are in Other RF products even ones that seemingly might not be in the frequency range do create harmonics and other artifacts that could interfere with the operation of the Wireless for HDMI FEATURES HDMI Features Supported e Resolutions up to 1080p Full HD e 12 bit Deep Color e Linear PCM digital audio up to 7 1 channels Dolby TrueHD Dolby Digital Plus and DTS HD Master Audio up to 5 1 channels e SDTV pass through e HDCP pass through e Lip Sync pass through Features e Wireless extension of HDMI up to 80 feet 25 meters Uncompressed High Definition A V from source to display No latency Included IR remote allows sequential switching between up to 8 sources Sender units It also features three direct access buttons for your most frequently used sources WHDI 1 0 FCC Part 15 and ETSI compliant Package Includes 1 Wireless for HDMI In Room Solution Sender unit 1 Wireless for HDMI In Room Solution Receiver unit 1 5 ft HDMI cables M M 1 USB to Mini USB cable 1 IR Remote Control 1 Cradle for Receiver unit 1 5V 1A DC Power Supply Sender 1 5V 2A DC Power Suppy Receiver 1 Quick Start Guide All features and specificati
10. iple Sender Units The Wireless for HDMI can be used with multiple Sender units to provide switching capability between up to eight Sender units Figure 1 Receiver unit shown with multiple Sender units Adding a new Video Source Before adding a secondary Sender unit to the Wireless for HDMI network make sure that a single Sender Receiver pair function correctly 1 2 Connect the Sender unit to a Hi Def source using an HDMI cable Connect the power supply to the Sender unit Point the IR Remote Control at the Receiver unit and press the MENU button The Setup menu will be displayed Setup gt Remove Video Source gt Modify Video Source Name gt Disconnect Wireless Link 12 OPERATING THE WIRELESS FOR HDMI 4 Use the cursor buttons on the IR Remote Control to select Add new Video Source from the Setup menu 5 Press the OK button The following message will be displayed Press and hold the Link button on Sender until Link LED stops blinking 6 Press and hold down the Pairing button see pages 6 8 on the Sender unit for about 5 seconds Adding Sender Press OK to continue or Exit to cancel 7 Press the OK button to continue adding the Sender unit NOTE When pairing multiple Senders it is recommended that you rename the ones already linked to avoid confusion 13 OPERATING THE WIRELESS FOR HDMI As the Sender unit is added to the Wireless for HDMI ne
11. on that requires the quick addition of portable devices such as a presentation laptop computer or a video camera to an existing A V system Additional features allow multiple Sender units where each display can access up to eight sources using the included handheld remote control How It Works Plug the Sender unit directly into the HDMI output of the source Connect the included HDMI cable from the Receiver unit to the HDTV display When using a PC as the source connect the supplied USB to mini USB cable from the PC to the Sender unit When using sources that do not have an available powered USB port you will need to use the provided USB power supply Connect the other power supply to the DC jack on the back of the Receiver unit Connect the power supplies to available electrical outlets Power up the source and the display Within approximately one minute the Video indicators on both units should now glow solid blue to indicate a successful connection between the Sender and Receiver unit If the Sender and Receiver units do not pair automatically the LEDs on the Sender will continue to blink Navigate through the on screen menu and have the Receiver unit look for a Sender unit If the remote is not available you can press and hold the recessed pairing button on the Receiver with a paper clip until its Link LED stops blink ing and goes dark Press and hold the pairing button on the Sender unit until the Link LED stops blinking and goes da
12. ons are subject to change without notice 5 PANEL LAYOUT Sender unit 3 pom AAA EA AAA AAA AAA AAA AAA AAA AAA apis Gefen f Link A o 0 Video Wireless for HDMI S dop PANEL LAYOUT Receiver unit 1988 6 00 0000000 u0 u 600 0 00U0 0 0XuweOOCO LOG 6 O aCq C OO OG da do0SsoL OHM ALOD v Ea yuol4 1 PANEL DESCRIPTIONS Sender Unit Video This LED indicator will glow bright blue once a video link is established between the Sender unit and the Receiver unit Pairing button Press and hold this button for 3 seconds to pair the Sender unit with the Receiver unit Link This LED indicator will glow bright blue once a link is established between the Sender unit and the Receiver unit USB Connect the included USB to Mini USB cable from the computer to this Mini B port HDMI Connector Connect the Sender unit to a Hi Def source using this HDMI connector Receiver Unit Pairing button Press and hold this recessed button using a paper clip for approximately 3 seconds to pair the Sender unit with the Receiver unit IR Sensor Receives IR commands from the included IR Remote Control unit and the IR remote of the source unit to be controlled Link This LED indicator will glow bright blue once a link is established between the Receiver unit and the Sender unit Video This LED indicator will glow bright blue once a video link is establi
13. re limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no responsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information refer to the Warranty and Return Policy under the Support section of the Gefen Web site at www gefen com PRODUCT REGISTRATION Please register your product online by visiting the Register Product page under the Support section of the Gefen Web site 29 Rev A5 080P SRx xMA GTV WHD 1 20600 Nordhoff St Chatsworth CA 91311 1 800 545 6900 818 772 9100 fax 818 772 9120 www gefentv com supportegefentv com Qu O KH ce amp This product uses UL or CE listed power supplies We
14. rk If navigating the menu using the remote press the OK button on the IR remote A message indicating that the Sender and the Receiver units have been paired will appear on the display FCC STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation INSTRUCTION TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and Receiver unit e Connect the equipment into an outlet on a circuit differ
15. shed between the Receiver unit and the Sender unit USB Mini USB service port for factory use only HDMI Out Connect the included HDMI cable from this connector to an HD display Power Connect the included 5V DC power supply to this receptacle IR REMOTE CONTROL UNIT Layout and Descriptions MENU EXIT SOURCE 1 Gero 9 AN 8 Gs 2D 3 f V Z INPUT DEVICES E3 Menu Press this button to display the Setup menu Cursor buttons Used to control Left Up Right and Down cursor motion within a menu system OK Press this button to accept the current operation or menu selection Delete When using multiple Sender units press this button to delete a Sender unit from the wireless network Input Devices When using multiple Sender units use these buttons to select any of the first three linked Sender units Use the Source button to select Senders 4 8 Guest Powers down the wireless system Add When using multiple Sender units press this button to add a Sender unit source Exit Press this button to cancel an operation or exit any menu system Source When using multiple Sender units sources press this button to select a different Sender unit 9 CONNECTING THE WIRELESS FOR HDMI How to Connect the Wireless for HDMI In Room Solution Connect the Sender unit directly to the HDMI port of the Hi Def source Connect an HD display or projector to the Receiver unit using the included H
16. sired source using the cursor buttons Then press the OK button to confirm the selection Select Video Source gt STB gt DVR Setup TIP Use the DELETE button on the IR Remote Control to jump directly to the Select Video Source menu when deleting sources 22 OPERATING THE WIRELESS FOR HDMI 10 The Connecting to status message will be displayed Connecting to DVR 11 After a few moments the selected source signal will be displayed Connected to DVR NOTE The video source will always need to be selected even if the source currently being viewed is not deleted 23 OPERATING THE WIRELESS FOR HDMI Disconnecting the Wireless Link The Wireless for HDMI network can be completely disconnected if necessary This can be used in order to restrict the source from being viewed 1 Point the IR Remote Control at the Receiver unit and press the MENU button 2 Select Disconnect Wireless Link and press the OK button Setup gt Add new Video Source gt Remove Video Source gt Modify Video Source Name gt Disconnect Wireless Link 3 After a few seconds the screen will go blank A status message indicating that the wireless has been turned off will be displayed The Wireless for HDMI network is now in standby mode Wireless Off 24 OPERATING THE WIRELESS FOR HDMI Reconnecting the Wireless Link 1 Press the Source button on the IR Remote Control The
17. twork a progress bar will be displayed Adding Sender I After a few moments the source signal connected to the additional Sender unit will be displayed Connected to Sender 8 If desired repeat steps 1 7 to add another Sender unit to the Wireless for HDMI network TIP Use the ADD button see page 9 on the IR Remote Control to bypass the Setup menu and jump directly to registering the Sender unit 14 OPERATING THE WIRELESS FOR HDMI Renaming Sources By default each Sender unit is assigned the name Sender This can be confusing when multiple Sender unit are used However this identifier can be changed to reflect for example the source to which each Sender unit is connected 1 Point the IR Remote Control at the Receiver unit press the MENU button select Modify Video Source Name then press the OK button Setup gt Add new Video Source gt Remove Video Source gt Modify Video Source Name 2 Select the source to rename from the menu by using the cursor keys Choose Source to Rename gt Sender gt Sender OPERATING THE WIRELESS FOR HDMI The Rename Video Source Name menu will be displayed along with the selected Source Use the A and Y cursor keys to change the highlighted character The A key moves forward within the list of available characters and the Y key moves backward through the list The list of available characters is listed in the tabl
18. umber of Sender units that can be used Each Sender unit needs to be placed at least 1 meter apart for optimum performance US Models Up to 4 pairs of Sender and Receiver units can be operated in the same environment Local RF interference can limit the number of units that can be used Each Sender unit needs to be placed at least 1 meter apart for optimum performance If additional Sender Receiver pairs are to be used each set of units must be placed beyond the reception range 80 feet 25 meters of the other in order to prevent interference Continued on next page OPERATION NOTES Continued from previous page EU Models Up to 2 pairs of Sender and Receiver units can be operated in the same environment Local RF interference can limit the number of units that can be used Each Sender unit needs to be placed at least 1 meter apart for optimum performance If additional Sender Receiver pairs are to be used each set of units must be placed beyond the reception range 80 feet 25 meters of each other in order to prevent interference IR back channel compatibility Only products with 38 kHz IR carrier frequency are compatible If in doubt please check with the equipment manufacturer Due to complexity in some manufacturers IR codes not all 38kHz IR devices may be compatible with the IR Back Channel of the Wireless for HDMI The following brands have been tested by Gefen Panasonic Sony and Samsung Operat
Download Pdf Manuals
Related Search