PureLink PT-E-HD10
Contents
1. may not work www purelink de ba 1 7 Installation Connect a HDMI or DVI source such as a Blu ray Disc player to the transmitting unit PT E HD10 TX Connect a HDMI or DVI display such as a LCD TV to the receiving unit PT E HD10 RX Connect IR Blaster Receiver to both TX and RX units Connect a Cat 5 5e 6 cable between the transmitting and receiving units Make sure this Cat 5 5e 6 cable is tightly connected and not loose Plug in 5V DC power supply unit to the power jack of the receiving unit PT E HD10 RX Plug in 5V DC power supply unit to the power jack of the transmitting unit PT E HD10 TX mn en Re If you see flickering or blinking image on the display please adjust the rotary control switch to improve the cable skew MAX stands for the strongest HDMI signal level for longest possible transmission length while MIN stands for the weakest HDMI signal level for short transmission length Please adjust the signal level from 7 to O and stop turning the rotary switch whenever the audio video is playing normally Inappropriate signal level setting may cause overpowering issue that would shorten the product life significantly 1 8 EDID Learning 1 Turn on to the transmitting unit TX of PT E HD10 2 Set the MODE rotary switch on the transmitting unit to 7 3 Use a HDMI cable to connect the transmitting unit TX of PT E HD10 and the display The LED on the RJ 45 port of the transmitting unit TX of PT E HD10 will dim and light ag2. signal level from MIN to MAX and stop turning the rotary switch whenever the audio video is playing normally Inappropriate signal level setting may cause overpowering issue that would shorten the product life significantly IR Receiver Infrared 3 5mm socket for plugging in the extension cable of IR receiver IR Blaster Infrared 3 5mm socket for plugging in the extension cable of IR blaster REAR PANEL PT E HD10 receiving unit RX SIGNAL IN 5V DC Connect to 5V DC power supply HDMI SIGNAL IN Plug in a Cat X cable and link to the RJ 45 port of the PT E HD10 transmitting unit TX www purelink de 6 1 6 IR Pass through IR Extenders IR Blaster IR Receiver IR Sockets IR Blaster Plug in the IR blaster here to emit all IR command signals received from the IR receiver to control the HDMI source devices IR Receiver Plug in the IR receiver here to receive all IR command signals from the IR remote controls of the HDMI source devices Wrongly insert IR blaster and IR receiver to wrong 3 5mm infrared sockets may result in the failure of the IR extenders Please check carefully before plugging in the IR extender to the respective IR sockets Definition of IR Earphone Jack IR Blaster IR Receiver You can buy any IR extension cables in the market that are compatible to the definition of the IR sockets for the matrix if necessary for replacement use However IR cables longer than 2m 6 ft
3. PureLink HDMI CAT Extender Extends 1 HDMI Signal over Single CAT with Bi directional IR pass through User s Guide Model no PT E HD10 Designed in Germany Made in Taiwan 2010 PureLink GmbH All rights reserved www purelink de ne Table of Contents Section GOS S ARE a E ee een bone due ee en a 3 sl STAR NO ae ee 3 L2 MEO UCT ON een de a ae 3 L3 Package COS ae da a ae Dee ee non 4 1 4 Belore SANTO a LIEEeEe 4 LS Prel DE OS sean cneancostaanconeranssamncesnantaeasnsareiseasarane 5 TG MR PASS UO WM a ane cas dede een E een ne ee nn 7 17 ASTON OR een een 8 1 8 EDD EE ee EA 8 Section 2 SDECIICSLION Sn em se ee an nee ae an eos 9 SECEION gt NO O ea an a onesasevese N 10 Section 4 Performance Guide 222s020200020000nannonannonnnnnnnannnnnnnnnnnnnnnansnnnnnnnsannnnanennsnennnn 11 www purelink de rs Section 1 Getting Started 1 1 Safety and Notice Please read all of these instructions carefully before you use the device Save this manual for future reference The PT E HD10 HDMI CAT Extender Extends 1 HDMI Signal over Single CAT with Bi directional IR pass through has been tested for conformance to safety regulations and requirements and has been certified for international use However like all electronic equipments the PT E HD10 should be used with care Please read and follow the safety instructions to protect yourself from possible injury and to minimize the risk of d
4. T PANEL PT E HD10 transmitting unit TX EDID SELECT HDMI IN IR RX IR TX MODE 0 EDID Full HD 1080p 60 24bit 2D video amp 7 1ch audio 1 EDID Full HD 1080p 60 24bit 2D video amp 2ch audio 2 EDID Full HD 1080p 60 36bit 2D video amp 7 1ch audio 3 EDID Full HD 1080p 60 36bit 2D video amp 2ch audio 4 EDID HD 1080p 30 1080i 60 720p 60 24bit 2D video amp 7 1ch audio 5 EDID HD 1080p 30 1080i 60 720p 60 24bit 2D video amp 2ch audio 6 EDID Full HD 1080p 60 36bit 3D video amp 2ch audio 7 EDID learning mode HDMI IN Connects to a HDMI source with a HDMI male male cable IR Receiver Infrared 3 5mm socket for plugging in the extension cable of IR receiver IR Blaster Infrared 3 5mm socket for plugging in the extension cable of IR blaster REAR PANEL PT E HD10 transmitting unit TX SIGNAL OUT 5V DC Connect to 5V DC power supply unit HDMI SIGNAL OUT Plug in a Cat X cable and link to the RJ 45 port of the PT E HD10 receiving unit RX www purelink de E3 FRONT PANEL PT E HD10 receiving unit RX SIGNAL LEVEL HDMI OUT IR RX IR TX HDMI OUT Connect to a HDMI display with a HDMI male male cable here SIGNAL LEVEL Adjust the equalization control to the received HDMI signals The HDMI signal level varies from MAX strongest to MIN weakest for respective transmission length from longest possible range to short distance Please adjust the
5. ain which indicates the EDID learning process is finished 4 Unplug everything and resume the steps in Installation www purelink de el Section 2 Specifications mem o ooo S Unis TransmitingunitofPT EHDIO Receiving unit of PT EHDIO Resolution and Distance Full HD 1080p 40meter 130feet CAT5e 50meter 165feet CAT6 8 bit HD 720p 1080i SOmeter 165feet CAT5e 60meter 200feet CAT6 Equatzation none Bevel Digtal Conol Human body model 19kV air gap discharge amp 12kV contact discharge Core chipset 8kV 1 x HDMI 1 x RJ45 1x 3 5mm 1x 3 5mm 1 x RJ45 1 x HDMI 1x 3 5mm 1x 3 5mm HDMI Connector Type A 19 pin female RJ45 Connector WE SS 8P8C with 2 LED indicators Conte IR blaster IR blaster IR receiver IR receiver Rotary Switch None Signal level equalization Dimensions 75 x 90 x 25mm LxWxH Power Supply 5V 2A DC 3 Watt max Environmental Operating Temperature 32 104 F 0 to 40 C Storage Temperature 4 140 F 20 60 C ESD Protection Relative Humidity 20 90 RH no condensation www purelink de ER Section 3 Notice 1 When adjusting the signal level on the receiver unit please dial the rotary control switch from MIN to MAX and stop turning the rotary switch whenever the audio video is playing normally Inappropriate signal level setting may cause overpowering issue that would shorten the product life significantly 2 If the DVI or HDMI devic
6. amage to the unit e Follow all instructions and warnings marked on this unit e Do not attempt to service this unit yourself except where explained in this manual e Provide proper ventilation and air circulation and do not use near water e Keep objects that might damage the device and assure that the placement of this unit is on a stable surface e Use only the power adapter and power cords and connection cables designed for this unit e Do not use liquid or aerosol cleaners to clean this unit Always unplug the power to the device before cleaning 1 2 Introduction The PT E HD10 HDMI CAT Extender Extends 1 HDMI Signal over Single CAT with Bi directional IR pass through boosts up your video audio transmission distance up to 60m 200ft in HDTV 1080i format and 40m 130ft in HDTV 1080p format PT E HD10 also supports the most advanced 3D video format complaint with HDMI specification and therefore guarantees the highest 3D video compatibility on the market With only one cost effective Cat X cable users can readily extend HDTV sources from DVD players Blu ray Disc player PS3 PC and any other kinds of sources compliant with TMDS to distant display monitors including HDMI or DVI enabled TV sets or LCD PC monitors With the advanced design for the latest HDMI technology deep color video DTS HD or Dolby TrueHD audio and HDCP supports and compatibility are all further insured This flexibility makes HDCP compliant DVD players or PS3
7. ant Minimize the cable skew by adjustable 8 level equalization control Pure unaltered uncompressed 7 1ch digital HDMI over Cat X cable transmission DTS HD and Dolby True HD high bit rate audio support Support full frequency IR signal from 20KHz to 60KHz Bi directional IR path Allows cascading Wall mounting housing design for easy and robust installation Perfectly integrated with other HDMI over Cat X series products The length depends on the characteristics and quality of the cables Higher resolutions and longer transmission distances require low skew cables lt 25ns 100m for best performance Unshielded CAT6 with metal RJ 45 connectors is recommended 1 3 Package Contents Before you start the installation of the switch please check the package contents PT E HD10 TX amp RX x1 Power supply unit 5VDC 2A x2 User s Guide x1 IR Blaster x1 IR Receiver x1 1 4 Before Installation e Put the product in an even and stable location If the product falls down or drops it may cause an injury or malfunction e Don t place the product in too high temperature over 50 C too low temperature under 0 C or high humidity e Use the DC power supply unit with correct specifications If inappropriate power supply is used then it may cause a fire e Do not twist or pull by force ends of the cable It can cause malfunction www purelink de Ea 1 5 Panel Descriptions FRON
8. e requires the EDID information please use EDID Reader Writer to retrieve and provide DVI or HDMI display EDID information 3 All HDMI over CATS transmission distances are measured using Belden 1583A CAT5e 125MHz UTP cable and ASTRODESIGN Video Signal Generator VG 859C 4 The transmission length is largely affected by the type of Cat 5 5e 6 cables the type of HDMI sources and the type of HDMI display The testing result shows solid UTP cables usually in the form of 300m 1 000ft bulk cables can transmit a lot longer signals than stranded UTP cables usually in the form of fixed length patch cords Shielded STP cables are better suited than unshielded UTP cables A solid UTP Cat 5e cable shows longer transmission range than stranded STP Cat 6 cable For long extension applications solid UTP STP cables are the only viable choice 5 EIA TIA 568 B termination T568B for Cat 5 5e 6 cables is recommended for better performance 6 To reduce the interference among the unshielded twisted pairs of wires in Cat 5 5e 6 cable one can use shielded STP cables to improve EMI problems which is worsen in long transmission 7 Because the quality of the CAT5 6 cables has the major effect on how long the transmission limit can achieve and how good is the received picture quality the actual transmission range is subject to one s choice of Cat 5 5e 6 cables For desired resolutions greater than 1080i or 1280x1024 a Cat 6 cable is recommended 8 If y
9. our HDMI display has multiple HDMI inputs it is found that the first HDMI input HDMI input 1 generally can produce better transmission performance among all HDMI inputs www purelink de ER Section 4 Performance Guide Performance rating Type of CAT5 6 cable Shielding CAT5 CAT5e CAT6 www purelink de Ra PureLink
10. transmit utmost high quality video and audio with a greater distance at the minimal cost when integrating several components apart In addition PT E HD10 is also equipped with bi directional IR pass through path This bonus feature allows users to boost IR control distance up to 100m 330 ft and makes IR control possible through only single Cat X cable including HDMI signals The PT E HD10 includes two units transmitting unit PT E HD10 TX and receiving unit PT E HD10 RX The transmitting unit is used to capture the input HDMI DVI signals with IR control packets and carry the signals via one cost effective Cat X cable The receiving unit is responsible for equalizing the transmitted HDMI signal and reconstructing IR signals The transmission distance between the sending and receiving units can be up to 60m 200ft at HD 720p or 1080i or 40m 130ft at Full HD 1080p With an 8 level equalization rotary control on the receiving unit users can adjust the equalization strength to the received www purelink de Ea HDMI signals accordingly and therefore optimize the transmission distance between source and destination Support HDMI Deep Color amp full 3D Extend the transmission up to 60m 200ft from the HDMI source at HD 1080i or 720p 24 bit Extend the transmission up to 40m 130ft from the HDMI source at Full HD 1080p 24 bit Extend the transmission up to 20m 65ft from the HDMI source at Full HD 1080p 36 bit HDCP 1 1 compli
Download Pdf Manuals
Related Search