Powerplus POW30540 rotary hammer
Contents
1. product Electric hammer drill 3 in 1 trade mark POWERplus model POW30540 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives as they relate to European harmonized standards Any unauthorized modification of the apparatus voids this declaration European Directives including if applicable their amendments 2004 108 EC 2006 42 EC 2000 14 EC Annex V LwA 101 dB A 104 dB A European harmonized standards including if applicable their amendments EN60745 1 2009 EN60745 2 6 2010 EN55014 1 2006 EN55014 2 1997 EN61000 3 2 2006 EN61000 3 3 2008 The undersigned acts on behalf of the company management E o MTN Pi _ Philippe Vankerkhove Certification Manager 11 07 2012 Copyright 2013 VARO Page 8 www varo com2. reverse switch to the left To make the drill rotate counter clockwise for removing screws push the forward reverse switch to the right Never change the position of the forward reverse switch while chuck is turning The trigger switch will NOT function with the forward reverse switch in the middle position 8 2 Trigger switch lock on button The trigger switch lock on feature allows the trigger switch to be locked in the ON position at full soeed when continuous operation for extended periods of time is required Fig 2 To lock the trigger switch in the ON position pull the trigger switch back fully to operate the drill at full speed While holding the trigger fully back push the lock on button 3 into the drill handle The drill will continue to run To release the lock on button pull the trigger switch back and then release the trigger 8 3 Drill hammer control The drill nammer control changes the drilling mode between conventional drilling and hammer for drilling concrete Fig 3 To change from drilling mode to hammer mode push the end of the drill hammer control knob inward and rotate the knob 180 to the hammer mode Reverse the procedure to change from hammer mode to drilling mode When the drill hammer control knob reaches the desired position release the end of the drill hammer control knob and move the knob back and forth slightly You will hear the knob lock into position AN Change the operati
3. following the instructions given in the manual inexpert assembly lightning strike erroneous net voltage This list is not exhaustive Acceptance of claims under warranty can never lead to the prolongation of the warranty period nor commencement of a new warranty period in case of a device replacement Devices or parts which are replaced under the warranty therefore remain the property of Varo NV Copyright 2013 VARO Page 7 www varo com POWERPLUS eth A POW30540 EN We reserve the right to reject a claim whenever the purchase cannot be verified or when it is clear that the product has not been properly maintained Clean ventilation slots carbon brushes serviced regularly etc Your purchase receipt must be kept as proof of date of purchase Your appliance must be returned undismantled to your dealer in an acceptably clean state in its original blow moulded case if applicable to the unit accompanied by proof of purchase 15 ENVIRONMENT p Should your appliance need replacement after extended use do not discard it Te with the household rubbish but dispose of it in an environmentally safe way Waste produced by electrical machine items should not be handled like normal household rubbish Please recycle where recycle facilities exist Check with your Local Authority or retailer for recycling advice 16 DECLARATION OF CONFORMITY VARO N V Joseph Van Instraat 9 BE2500 Lier BELGIUM declares that
4. DESIGNED AND MARKETED BY VARO P OW30 5 4 0 E N ELECTRIC HAMMER DRILL 31N 1 POW30540 1 APPLICATION The machine is intended for hammer drilling in concrete brick and stone It is also suitable for drilling without impact in wood metal ceramic and plastic Machines with electronic control and right left rotation are also suitable for screw driving It is not designed for commercial use instructions carefully before using the appliance Your power tool should WARNING For your own safety read this manual and general safety only be passed on together with these instructions DESCRIPTION FIG A SDS plus chuck Hammer function selector Air vents Forward reverse knob On Off switch Lock button PACKAGE CONTENT LIST Remove all packaging materials Remove remaining packing and package inserts if included Check that the package contents are complete Check the appliance the power cord the power plug and all accessories for transportation damage Keep the packing materials as long as possible till the end of the warranty period Dispose it into your local waste disposal system afterwards s a ss t Oo bOhi A Pp WARNING Packaging materials are not toys Children must not play with plastic bags Danger of suffocation Electric hammer drill 3 in 1 O If any parts are missing or damaged please contact your dealer 4 SYMBOLS In this manual and or on the machine the following symbols are used Wear noise pro
5. POWERPLUS E ul POW30540 EN 1 APPLICATION WEE 2 2 DESCRIPTION FIG A 2 3 PACKAGE CONTENT LIST wsisicessccvsistecscticswesucenscseneensusszwecsunartnneensses 2 4 Seege 2 5 GENERAL POWER TOOL SAFETY WARNINGS cssseseeeeees 3 5 1 WoOrki g QU CG seseriai E E E R ERS 3 5 2 Eeer 3 5 3 Personal E 3 5 4 Pow r 100 use and Cale siete ene anne ieee nena 4 5 5 ENEE d 6 MACHINE SPECIFIC SAFETY WARNINGS cccccssssseeeseeeeneees 4 7 eege 4 7 1 IO VICSS CHUCK scssi 4 8 OPERA TION WE 5 8 1 Forward reverse selector right left rotation selector Fig 2 c scccsnseccsnsecennnesennnes 5 8 2 Trigger switch lock on DURON siorse a 5 8 3 Di hammer e de EE 5 8 4 Selling Deeg eege eege AEREE AR 6 8 5 Inserting SDS Plus Drilling Tools Fig 4 ssssccccccennnenccceeeennnnsceseeeennnssesseeeenannnnees 6 8 6 Removing SDS Plus Drilling Tools Fig 4 1 0ssscccccceennnesecseeeennnssesseeeennessnsseeeenaaes 6 H CLEANING AND MAINTENANCE cccccccsessseeesseesseeesseeeeneees 6 9 1 Clean Osses E E A E E E 6 Ur TECHNICAL DATA assesses tase aaa aia 6 11 NORSE a ceca unwconcauetcesesseeneseuncesceiaeewsencuuueesseccerwenecsceuveceuseses 7 12 SERVICE a an LE KR 7 MO E cca cette ces tenes dee sete E ee sten uae ceseueuixweecuseereeeerees 7 14 WARRANTY EE 7 0 2 AT ei Ode WEE 8 16 DECLARATION OF CONFORMITY ccccccssssssseeesesessseeeseoeess 8 Copyright 2013 VARO Page 1 www varo com POWERPLUS
6. arthed Do not expose power tools to rain or wet conditions If water gets inside a power tool it will increase the risk of an electric shock Do not damage the cord Never use the cord for carrying pulling or unplugging the power tool Keep the cord away from heat oil sharp edges or moving parts Damaged or entangled cords increase the risk of an electric shock When operating a power tool outdoors use an extension cable suitable for outdoor use Using a cord suitable for outdoor use reduces the risk of an electric shock If operating a power tool in a damp location is unavoidable use a power supply protected by a residual current device RCD Using an RCD reduces the risk of an electric shock Personal safety Stay alert watch what you are doing and use common sense when operating a power tool Do not use a power tool when you are tired or under the influence of drugs alcohol or medication A moment of inattention when operating a power tool may result in serious personal injury Use safety equipment Always wear eye protection Using safety equipment such as a dust mask non skid safety shoes a hard hat or hearing protection whenever it is needed will reduce the risk of personal injury Avoid accidental starts Ensure the switch is in the off position before inserting the plug Carrying power tools with your finger on the switch or plugging in power tools when the switch is in the on position makes accidents more likely Remove any adjustin
7. etrol alcohol ammonia water etc These solvents may damage the plastic parts 10 TECHNICAL DATA Rated voltage 220 240 V Rated frequency 50 Hz Rated power 400 W Rotation speed 0 1100 min Protection class II Drill capacity concrete 10 mm Drill capacity steel 8 mm Drill capacity wood 16 mm Impact rate 0 4800 min Cable length 2m VDE plug Chuck type 10mm SDS type chuck Copyright 2013 VARO Page 6 www varo com POWERPLUS DESIGNED AND MARKETED BY VARO P OW30 5 4 0 E N 11 NOISE Noise values measured according to relevant standard K 3 Acoustic pressure level LpA 93 dB A Acoustic power level LwA 104 dB A ATTENTION The sound power level may exceed 85 dB A in this case individual hearing protection shall be worn aw Vibration 11 9 m s K 1 5 m s ue SERVICE DEPARTMENT Damaged switches must be replaced by our after sales service department If the connecting cable or mains plug is damaged it must be replaced by a special connecting cable which is available from our service department Replacement of the connecting cable should only be carried out by our service department see last page or by a specialist qualified electrician 13 STORAGE Thoroughly clean the whole tool and its accessories Store it out of the reach of children in a stable and secure position in a cool and dry place avoid too high and too low temperatures Protect it from exposure to direct sunlight Keep i
8. g keys or spanners before turning on the power tool A spanner or key left attached to a rotating part of the power tool may result in personal injury Do not reach out too far Keep your feet firmly on the ground at all times This will enable you retain control over the power tool in unexpected situations Dress properly Do not wear loose clothing or jewellery Keep your hair clothing and gloves away from the power tool Loose clothes jewellery or long hair can become entangled in the moving parts If there are devices for connecting dust extraction and collection facilities please ensure that they are attached and used correctly Using such devices can reduce dust related hazards Copyright 2013 VARO Page 3 www varo com POWERPLUS eth tA a POW30540 EN 5 4 Power tool use and care Do not expect the power tool to do more than it can Use the correct power tool for what you want to do A power tool will achieve better results and be safer if used in the context for which it was designed Do not use the power tool if the switch cannot turn it on and off A power tool with a broken switch is dangerous and must be repaired Disconnect the plug from the power source before making adjustments changing accessories or storing power tools Such preventive safety measures reduce the risk of starting the power tool accidentally Store power tools when not in use out of the reach of children and do not allow people who are not famil
9. iar with the power tool or these instructions to operate it Power tools are potentially dangerous in the hands of untrained users Maintain power tools Check for misalignment or jammed moving parts breakages or any other feature that might affect the operation of the power tool If it is damaged the power tool must be repaired Many accidents are caused by using poorly maintained power tools Keep cutting tools sharp and clean Properly maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control Use the power tool accessories and cutting tools etc in accordance with these instructions and in the manner intended for the particular type of power tool taking into account the working conditions and the work which needs to be done Using a power tool in ways for which it was not intended can lead to potentially hazardous situations 5 5 Service Your power tool should be serviced by a qualified specialist using only standard spare parts This will ensure that it meets the required safety standards 6 MACHINE SPECIFIC SAFETY WARNINGS Use appropriate detectors to determine if utility lines are hidden in the work area or call the local utility company for assistance Switch off the power tool immediately when the tool insert jams Be prepared for high reaction torque that can cause kickback Hold power tool by the insulated gripping surfaces when performing an operation where the cutting
10. ng mode only when the machine is switched off Otherwise the machine can be damaged Copyright 2013 VARO Page 5 www varo com POWERPLUS DESIGNED AND MARKETED BY VARO P OW30 5 40 E N 8 4 Setting the Speed Impact rate The speed impact rate of the switched on power tool can be variably adjusted depending on how far the On Off switch is pressed Light pressure on the On Off switch results in low speed impact rate Further pressure on the switch increases the speed impact rate AN Drilling at a slow drilling speed for an extended period of time may cause the drill motor to overheat If the drill gets hot stop drilling and allow it to cool for at least 15 minutes 8 5 Inserting SDS Plus Drilling Tools Fig 4 Clean and lightly grease the shank end of the tool Insert the tool in a twisting manner into the tool holder until it latches itself Check the latching by pulling the tool 8 6 Removing SDS Plus Drilling Tools Fig 4 Push back the locking sleeve 1 and remove the tool 9 CLEANING AND MAINTENANCE AN Attention Before performing any work on the equipment pull the power plug Keep the ventilation slots of the tool clean to prevent overheating of the engine Regularly clean the tool housing with a soft cloth preferably after each use Keep the ventilation slots free from dust and dirt If the dirt does not come off use a soft cloth moistened with soapy water 9 1 Cleaning Never use solvents such as p
11. t in the dark if possible Don t keep it in plastic bags to avoid humidity build up ba WARRANTY This product is warranted as provided by law for a 24 month period effective from the date of purchase by the first user This warranty covers all material or production flaws excluding batteries chargers defective parts subject to normal wear amp tear such as bearings brushes cables and plugs or accessories such as drills drill bits saw blades etc damage or defects resulting from maltreatment accidents or alterations nor the cost of transportation Damage and or defects resulting from inappropriate use also do not fall under the warranty provisions We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool Repairs may only be carried out by an authorised customer service centre for Powerplus tools You can always obtain more information at the number 00 32 3 292 92 90 Any transportation costs shall always be borne by the customer unless agreed otherwise In writing At the same time no claim can be made on the warranty if the damage of the device is the result of negligent maintenance or overload Definitely excluded from the warranty is damage resulting from fluid permeation excessive dust penetration intentional damage on purpose or by gross carelessness inappropriate usage use for purposes for which the device is not suitable incompetent usage e g not
12. tection In accordance with essential requirements of the European directive s Copyright 2013 VARO Page 2 www varo com POWERPLUS DESIGNED AND MARKETED BY VARO POW30540 EN 5 GENERAL POWER TOOL SAFETY WARNINGS Read all safety warnings and instructions Failure to heed warnings and follow instructions may result in electric shock fire and or serious injury Keep safety warnings and instructions for future reference The term power tool in the safety warnings refers to your mains operated corded power tool or battery operated cordless power tool 5 1 Working area Keep working area clean and well lit Untidy and dark areas can lead to accidents Do not operate power tools in potentially explosive surroundings for example in the presence of inflammable liquids gases or dust Power tools create sparks which may ignite the dust or fumes Keep children and bystanders at a distance when operating a power tool Distractions can cause you to lose control of it Electrical safety Always check that the power supply corresponds to the voltage on the rating plate Power tool plugs must match the outlet Never modify the plug in any way Do not use adapter plugs with earthed power tools Unmodified plugs and matching outlets will reduce the risk of an electric shock Avoid body contact with earthed surfaces such as pipes radiators kitchen ranges and refrigerators There is an increased risk of an electric shock if your body is e
13. tool may run into hidden wiring When working with the machine always hold it firmly with both hands and provide for a secure stance Secure the work piece Keep your workplace clean Always wait until the machine has come to a complete stop before placing it down Before any work on the machine e g maintenance tool change etc as well as during transport and storage set the rotational direction switch to the centre position 7 FEATURES 7 1 Keyless chuck Your drill has a keyless chuck that allows you to hand tighten or release drill bit in the chuck jaws SDS plus The SDS Plus tool holder allows for simple and convenient changing of ae drilling tools without the use of additional tools Copyright 2013 VARO Page 4 www varo com POWERPLUS DESIGNED AND MARKETED BY VARO P OW30 5 40 EN Due to their working principle SDS Plus drilling tools move freely This results in radial run out at no load However this has no effect on the accuracy of the drill hole as the drill bit centres itself during drilling The SDS Plus tool holder can also accommodate different drill bit types with hexagon shank Use only bit with SDS Plus Other bits can be used with a keyless chuck with SDS Plus 8 OPERATION 8 1 Forward reverse selector right left rotation selector Fig 2 The drill has a forward reverse selector located above the switch trigger To make the drill rotate clockwise for drilling or driving screws push the forward
Download Pdf Manuals
Related Search