Hikvision Digital Technology DS-2CE1582P-VFIR3 surveillance camera
Contents
1. HIKVISION Bullet Camera User Manual UD 6L0201D1104A01 www hikvision com Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact the dealer This manual applies to Type Model DS 2CE1512P N IR DS 2CE1582P N IR l DS 2CE15A2P N IR DS 2CE15C2P N IR DS 2CE1582P N IRP DS 2CE15A2P N IRP DS 2CE1682P N IT1 DS 2CE16A2P N IT1 Il DS 2CE16C2P N IT1 DS 2CE1682P N IT3 DS 2CE16A2P N IT3 DS 2CE16C2P N IT3 DS 2CE1682P N IT5 DS 2CE16A2P N ITS mM DS 2CE16C2P N ITS DS 2CE1582P N VFIR3 DS 2CE15A2P N VFIR3 v DS 2CE15C2P N VFIR3 This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual 0200001030603 Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio commu2. ction properly please contact your dealer or the nearest service center Donot disassemble the camera for repair or maintenance by yourself Please make sure that the ceiling or the wall is strong enough to withstand 3 times the weight of the camera 2 1 Ceiling Mounting for Type Camera Steps 1 Drill the screw holes and the cable hole inthe ceiling according to the supplied drill template 2 Hammer the supplied plastic expansion bolt into the screw holes i SerewHiolel ss Figure 2 1 Drill Template 3 Route the cables to the cable hole and connect the corresponding power cable and video cable 4 Fix the camera to the ceiling with the supplied screws RA A YX Figure 2 2 Fix the Camera to the Ceiling 5 Adjust the surveillance angle 1 Loosen No 3 adjusting screw to adjust the panning position 0 360 2 Tighten No 3 adjusting screw 3 Loosen the No 2 adjusting screw to adjust the tilting position 0 90 4 Tighten No 2 adjusting screw 5 Loosen No 1 adjusting screw to adjust the azimuth angle of the image 0 360 6 Tighten No 1 adjusting screw Figure 2 3 3 axis Adjustment 2 2 Wall Mounting for Type II III Camera Steps 1 Drill the screw holes and the cable hole inthe ceiling according to the drill template 2 Hammer the supplied plastic expansion bolt into the screw holes 2 Ceiling Mounting 4 2 No 1 Screw Hole No 2 Screw Ho
3. he azimuth angle of the image 0 360 6 Tighten No 1 adjusting screw Figure 2 9 3 axis Adjustment 6 Adjust the zoom and the focus 1 Output the image to the monitor 2 Push forward to remove the adjusting sheet located on the bottom of the camera See figure below 3 Insert the removed adjusting sheet to zoom slot and focus slot to adjust the zoom and the focus 4 Put the adjusting sheet back after the adjustment is done Adjusting Sheet Figure 2 10 Focus and Zoom Adjustment 2 4 Power Supply a Figure 2 11 The Powe Cable amp the Video Cable Note Please make sure that the power adapter is compatible with the camera and the standard power supply is 12V DC Please refer to the technical specification for more information
4. le for Bracket for Mounting Base 1 K 2 Figure 2 4 Drill Template 3 Route the cables to the cable hole and connect the corresponding power cable and video cable 4 Fix the camera to the wall with the supplied screws A Figure 2 5 Fix the Camera to the Wall 5 Adjust the surveillance angle 1 Loosen No 3 adjusting screw to adjust the pan position 0 360 2 Tighten No 3 adjusting screw 3 Loosen No 2 adjusting screw to adjust the tilting position 0 90 4 Tighten No 2 adjusting screw 5 Loosen No 1 adjusting screw to adjust the rotation position 0 360 6 Tighten No 1 adjusting screw Figure 2 6 3 axis Adjustment 2 3 Ceiling Mounting for Type IV Camera Steps 1 Drill the screws holes and the cable hole on the ceiling according to the supplied drill template 2 Hammer the supplied plastic expansion bolt into the screw holes Figure 2 7 Drill Template 3 Route the cables to the cable hole and connect the corresponding cables 4 Fix the camera to the ceiling with the supplied screws Figure 2 8 Fix the Camera to the Ceiling 5 Adjust the surveillance angle 1 Loosen No 3 adjusting screw to adjust the panning position 0 360 2 Tighten No 3 adjusting screw 3 Loosen No 2 adjusting screw to adjust the tilting position 0 90 4 Tighten No 2 adjusting screw 5 Loosen No 1 adjusting screw to adjust t
5. nications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU 2012 19 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European a mign For proper recycling bsesb this product to your local supplier upon the purchase of equivalent new equipment or dispose of it at designated collection points For more information see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or merc
6. ury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info 1 Introduction 1 1 Product Features This series of camera adopts new generation sensor with high sensitivity and advanced circuit design technology It features high resolution low image distortion and low noise features etc which makes it suitable for surveillance system and image processing system High performance sensor and high resolution bring high quality image R LED enables the day night surveillance IR cut filter auto switch ATW brings high color rendition Ingress protection IP66 1 2 Overview Video Cable A Mounting Base CSS 3 OEE N Sun Shield Power Cable Figure 1 1 Overview of Type I Camera Sun Shield Adjustable Screw Power Cable Video Cable IR LED Figure 1 2 Overview of Type Il Camera Adjustable Screw Sun Shield Power Cable Video Cable IR LED Figure 1 3 Overview of Type Ill Camera Video Cable Power Cable Sun Shield Figure 1 4 Overview of Type IV Camera 2 Installation Before you start Make sure that all the related equipment is power off during the installation Check the specification of the products for the installation environment Check whether the power supply is matched with your AC outlet to avoid damage eif the product does not fun
Download Pdf Manuals
Related Search