Ctek MXS 7.0
Contents
1. 2011 10 11 07 58 03 CONNECT AND DISCONNECT THE CHARGER TO A BATTERY Comfort Connect Comfort Connect 2 6 EN 20015462E MXS 7 0 Manual EU Print file 002 indd 6 INFO If the battery clamps are incor rectly connected the reverse polarity protection will ensure that the battery and charger are not damaged For batteries mounted inside a vehicle 1 Connect the red clamp to the bat tery s positive pole 2 Connect the black clamp to the vehicle chassis remote from the fuel pipe and the battery 3 Connect the charger to the wall socket 4 Disconnect the charger from the wall socket before disconnecting the battery 5 Disconnect the black clamp before the red clamp Some vehicles may have posi tively earthed batteries 1 Connect the black clamp to the bat tery s negative pole 2 Connect the red clamp to the vehicle chassis remote from the fuel pipe and the battery 3 Connect the charger to the wall socket 4 Disconnect the charger from the wall socket before disconnecting the battery 5 Disconnect the red clamp before the black clamp TECHNICAL SPECIFICATIONS Charger model Model number Rated Voltage AC Charging voltage Start voltage Charging current Current mains Back current drain Ripple Ambient temperature Charger type Battery types Battery capacity Dimensions Insulation class Weight MXS 7 0 1053 220 240VAC 50 60Hz NORMAL 14 4V AGM So 14 7V RECOND2. 15 8V SUPPLY 13 6V 2 0V 7 2A max 1 2A rms at full charging current lt 1Ah month lt 4 20 C to 50 C output power is reduced automatically at high temperatures 8 step fully automatic charging cycle All types of 12V lead acid batteries WET MF Ca Ca AGM and GEL 14 150Ah up to 225Ah for maintenance 191 x 89 x 48mm L x W x H IP65 0 8kg Back current drain is the current that drains the battery if the charger is not connected to the mains CTEK chargers has a very low back current The quality of the charging voltage and charging current is very important A high current ripple heats up the battery which has an aging effect on the positive electrode High voltage ripple could harm other equipment that is connected to the battery CTEK battery chargers produce very clean voltage and current with low ripple 2011 10 11 07 58 04 SAFETY The charger is designed for charging 12V lead acid batteries Do not use the charger for any other purpose Check the charger cables prior to use Ensure that no cracks have occurred in the cables or in the bend protection A charger with damaged cables must not be used A damage cable must be replaced by a CTEK representative Never charge a damaged battery Never charge a frozen battery Never place the charger on top of the battery when charging Always provide for proper ventilation during charging Avoid covering the charger A battery being charged could
3. 0 Manual EU Print file 002 indd 3 2011 10 11 07 58 00 CHARGING PROGRAMS ERROR LAMP Settings are made by pressing the MODE button After about two seconds the charger IF the error lamp is lit check the following activates the selected program The selected program will be restarted next time the charger is connected 1 Is the chargers positive lead connected to the batterys positive pole The table explains the different Charging Programs 2 Is the charger connected to a 12V battery Battery Program size Ah Explanation 3 The clamps are short circuited Temp range 4 Has charging been interrupted in L or ili Restart the charger by pressing the MODE button If charging is still being interrupted the battery DI is seriosly sulphated and may need to be replaced can not accept charge and may need to be replaced Normal battery program 5 C 50 C NORMAL 14 225Ah 14 4V 7A Use for WET batteries 41 F 122 F Ca Ca MF and for most GEL batteries AGM battery program 14 7V 7A 20 C 5 C E 14 225Ah Use for AGM batteries 4 F 41 F Ml cannot keep charge and may need to be replaced Recond program 15 8V 1 5A 20 C 50 C Use to return energy to the empty 4 F 122 F WET and Ca Ca batteries Recond your battery once per year and after deep dischare to maximise lifetime and capacity The Recond program adds the 14 225Ah Recond step to the normal battery prog
4. CONGRATULATIONS CHARGING to the purchase of your new professional switch mode battery charger This charger is included in a series of professional chargers from CTEK SWEDEN AB and represents the latest technology in battery charging 2 Connect the charger to the wall socket The power lamp will indicate that the mains cable is connected to the wall socket The error lamp will indicate if the battery clamps are incorrectly connected The reverse polarity protection will ensure that the battery or charger will not be damaged iz 1 Connect the charger to the battery 3 Press the MODE button to select charging program SUPPLY PLUG MAINS CABLE 4 Follow the indication lamps through the charging process P4 The battery is ready to start the engine when gg is lit Y The battery is fully charged when jg is lit 5 Stop charging at any time by disconnecting the mains cable from the wall socket CTEK COMFORT CONNECT ABSORPTION READY TO USE ANALYSE AN a PP Du m CHARGE CABLE TI N amp wd IC SOFI START BULK PULSE MAINTENANCE CHARGING DESULPHATION FLOAT FULLY CHARGED ERROR LAMP SUPPLY RECOND MODE BUTTON CTEK COMFORT CONNECT eyelet M8 CTEK COMFORT CONNECT clamp POWER i i LAMP Supply plugs may differ to suit your wall socket SUPPLY RECOND NORMAL 7 BATTERY AGM SUPPLY RECOND PROGRAM BATTERY PROGRAM PROGRAM PROGRAM EN 3 20015462E MXS 7
5. ance with the national regulations for electrical installations 20015462E MXS 7 0 Manual EU Print file 002 indd 7 LIMITED WARRANTY CTEK SWEDEN AB issues this limited warranty to the original purchaser of this product This limited warranty is not transferable The warranty applies to manufacturing faults and material defects for 5 years from the date of purchase The customer must return the product together with the receipt of purchase to the point of purchase This warranty is void if the battery charger has been opened handled carelessly or repaired by anyone other than CTEK SWEDEN AB or its authorised representatives One of the screw holes in the bottom of the charger is sealed Removing or damaging the seal will void the warranty CTEK SWEDEN AB makes no warranty other than this limited warranty and is not liable for any costs other than those mentioned above i e no consequential damages Moreover CTEK SWEDEN AB is not obligated to any warranty other than this warranty SUPPORT CTEK offers a professional customer support www ctek com For latest revised user manual see www ctek com By e mail info ctek se by telephone 46 0 225 351 80 by fax 46 0 225 351 95 By mail CTEK SWEDEN AB Rostugnsv gen 3 SE 776 70 VIKMANSHYTTAN SWEDEN VIKMANSHYTTAN SWEDEN 2011 09 01 AAA sa Bengt Hagander President CTEK SWEDEN AB EN 7 2011 10 11 07 58 05 CTEK PRODUCTS ARE PROTECTED BY Patents EP10156636 2 pen
6. ding US12 780968 pending EP1618643 US7541778 EP1744432 EP1483817 pending SE524203 US7005832B2 EP1716626 pending SE52663 US7638974B2 EP1903658 pending EP09180286 8 pending US12 646405 pending EP1483818 SE1483818 US7629774B2 09170640 8 pending US12 564360 pending SE528232 SE525604 m 8 EN 2011 09 19 Designs Trade marks RCD 509617 CTM 669987 US D575225 CTM 844303 US D580853 CTM 372715 US D581356 CTM 3151800 US D571179 CTM 1461716 pending RCD 321216 CTM 1025831 RCD 000911839 CTM 405811 RCD 081418 CTM 830545751 pending RCD 001119911 0001 CTM 1475420 pending RCD 00111991 1 0002 CTM 1935061 pending RCD 081244 V28573IP00 RCD 321198 CTM 1082141 pending RCD 321197 CTM 20100041 18 pending ZL 200830120184 0 CTM 4 2010 500516 pending ZL 200830120183 6 CTM 410713 RCD 001505138 0001 CTM 2010 05152 pending RCD 000835541 0001 CTM1042686 RCD 000835541 0002 CTM 766840 pending D596126 D596125 RCD 001705138 pending US D29 378528 pending RCD 201030618223 7 pending US RE42303 US RE42230 20015462E MXS 7 0 Manual EU Print file 002 indd 8 20015462E 2011 10 11 07 58 05
7. emit explosive gasses Prevent sparks close to the battery When batteries are reaching the end of their lifecycle internal sparks may occur All batteries fail sooner or later A battery that fails during charging is normally taken care of by the chargers advanced control but some rare errors in the battery could still exist Don t leave any battery during charging unattended for a longer period of time Ensure that the cabling does not jam or comes into contact with hot surfaces or sharp edges Battery acid is corrosive Rinse immediately with water if acid comes into contact with skin or eyes seek immediate medical advice e Always check that the charger has switched to gill before leaving the charger unattended and connected for long periods If the charger has not switched to N within 45 hours this is an indication of an error Manually disconnect the charger e Batteries consume water during use and charging For batteries where water can be added the water level should be checked regularly If the water level is low add distilled water This appliance is not designed for use by young children or people who cannot read or understand the manual unless they are under the supervision of a responsible person to ensure that they can use the battery charger safely Store and use the battery charger out of the reach of children and ensure that children cannot play with the charger Connection to the mains supply must be in accord
8. ram Freguent use of the Recond program may cause water loss in the batteries and reduce service life of electronics Contact your vehicle and battery supplier for advice READY TO USE The table shows the estimated time for empty battery to 8096 charge SL Aia e Lu RECOND Supply program 13 6V 7A 20 C 50 C SUPPLY Use as 12V power supply or use for 4 F 122 F PANAI 14 225Ah float maintenance charging when 100 BATTERY SIZE Ah TIME TO 80 CHARGED capacity of the battery is required 20Ah 2h Supply program activates Float step without time or voltage limitation 50Ah 6h 100Ah 12h 150Ah 17h WARNING The spark protection on the battery charger is disabled during SUPPLY program 4 EN 20015462E MXS 7 0 Manual EU Print file 002 indd 4 2011 10 11 07 58 02 CHARGING PROGRAM DESULPHATION VOLTAGE V CURRENT A SOFT START BULK BRERA TEENI P 7A until 12 6V Increasing voltage 14 4V 25 C Checks Checker voltage voltage NORMAL to 14 4V 25 C Declining current drops to 12V 7A 14 7V ZA until 12 6V Increasing voltage 14 7V 25 C Checks if voltage AGM to 14 7V 25 C Declining current drops to 12V 7A 14 4V 7A until 12 6V Increasing voltage 14 4V 25 C Checks if voltage RECOND to 14 4V 25 C Declining current drops to 12V STEP 1 DESULPHATION Detects sulphated batteries Pulsing current and voltage remove
9. s sulphate from the lead plates of the battery restoring the battery capacity STEP 2 SOFT START Tests if the battery can accept charge This step prevents that charging proceeds with a defect battery STEP 3 BULK Charging with maximum current until approximately 80 battery capacity STEP 4 ABSORPTION Charging with declining current to maximize up to 100 battery capacity 20015462E MXS 7 0 Manual EU Print file 002 indd 5 STEP 5 ANALYSE STEP 6 RECOND Choose the Recond program to add the Recond step to the charging process During the Recond step 30 min or 4h depending on battery voltage back energy to the battery STEP 7 FLOAT Maintaining the battery voltage at maximum level by providing a constant voltage charge STEP 8 PULSE Maintaining the battery at 95 100 capacity The charger monitors the battery voltage and gives a pulse when necessary to keep the battery fully charged Max 15 8V 1 5A Pen PULSE O 12 9V 14 4V 7A 7 2A 13 6V 12 9V 14 7V 7A 7 2A 13 6V 12 9V 14 4V 7A 7 2A Max 13 6V 7A 10 days Charge cycle restarts if voltage drops Charge cycle restarts if voltage drops Supply program is not time or voltage limited Tests if the battery can hold charge Batteries that can not hold charge may need to be replaced voltage increases to create controlled gasing in the battery Gasing mixes the battery acid and gives EN 5
Download Pdf Manuals
Related Search