Siig JU-SA0812-S3
Contents
1. years from the date of purchase of the product SIIG will at our discretion repair or replace with an identical product or product having similar features and functionality the product if defective in materials or workmanship This warranty gives you specific legal rights and you may also have other rights which vary from state to state Please see our web site for more warranty details If youencounter any problems with this product please follow the procedures below A If it is within the store s return policy period please return the product to the store where you purchased it B If your purchase has passed the store s return policy period please follow these steps to have the product repaired or replaced Step 1 Submit your RMA request Go to www siig com click Support then Request A Product Replacement to submit a request to SIG RMA or fax a request to 510 657 5962 Your RMA request will be processed if the product is determined to be defective an RMA number will be issued Step 2 After obtaining an RMA number ship the product e Properly pack the product for shipping All software cable s and any other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package SIIG will refuse to accept any shipping package and will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton e You are2. NAME USB 3 0 to SATA 6Gb s Adapter FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCESTATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA Phone 510 657 8688 USB 3 0 to SATA 6Gb s Adapter is a trademark of SIG Inc SIIG and the SIG logo are registered trademarks of SIG Inc Microsoft and Windowsare registered trademarks of Microsoft Corporation All other names used in this publication are for identification only and may be trademarks of their respective owners April 2013 Copyright 2013 by SIG Inc All rights reserved
3. responsible for the cost of shipping to SIIG Ship the product to the following address SIIG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA e SIG will ship the repaired or replaced product via Ground in the U S and International Economy outside of the U S at no cost to the customer About SIIG Inc Founded in 1985 SIIG Inc is a leading manufacturer of IT connectivity solutions including Serial ATA and Ultra ATA Controllers FireWire USB and legacy I O adapters that bridge the connection between Desktop Notebook systems and external peripherals SIIG continues to grow by adding A V and Digital Signage connectivity solutions to our extensive portfolio All centered around the distribution and switching of A V signals over CAT5 6 these products include matrix switches distribution amplifiers extenders converters splitters cabling and more SIIG is the premier one stop source of upgrades and is committed to providing high quality products while keeping economical and competitive prices High quality control standards are evident by one of the lowest defective return rates in the industry Our products offer comprehensive user manuals user friendly features and most products are backed by a lifetime warranty SIIG products can be found in many computer retail stores mail order catalogs and e commerce sites in the Americas as well as through major distributors system integrators and VARs PRODUCT
4. USB 3 0 to SATA 6Gb s P Adapter Quick Installation Guide Introduction The USB 3 0 to SATA 6Gb s Adapter quickly adds SATA hard disk or SATA DVD CD ROM to your system through USB 3 0 interface Features and Benefits Ultra portable design makes it perfect for travel and use with notebook laptop computers 10X faster than USB 2 0 USB 3 0 with data transfer rate up to 5Gb s Supports Serial ATA bus bandwidth up to 6Gb s Quickly access data on your SATA hard disks or DVD CD ROM drives Ultra fast for backup and copying large files Backwards compatible to USB 2 0 and USB 1 1 Plug and play and no additional drivers needed Note This device does not support port multipliers System Requirements Desktop or notebook PC with an available USB port USB 3 0 recommended Windows 8 32 64 bit 7 32 64 bit Vista 32 64 bit XP 32 64 bit Server 2003 amp 2008 32 64 bit Server 2008 R2 04 0640C 1 Package Contents e USB 3 0 to SATA 6Gb s Adapter e Switching power adapter e Quick installation guide Layout Power jack Power Activity LED Serial ATA gt connector ar USB Type A connector SATA power connector Figure 1 Layout Note The Power Activity LED illuminates whena SATA hard disk drive or SATA DVD CD ROM is connected and powered up The LED flashes during data transfer or accessing the DVD CD ROM drive Hardware Installation Static Electricity D
5. ischarge may permanently damage your system Discharge any static electricity build up in your body by touching your computer case for a few seconds Avoid any contact with internal parts and handle cards only by their external edges 1 Connect the USB 3 0 to SATA 6Gb s Adapter to a USB port USB 3 0 recommended of your system 2 Connect your SATA hard disk or SATA DVD CD ROM to the SATA connector of the USB 3 0 to SATA 6Gb s Adapter 3 Plug the switching power adapter into the power jack of the USB 3 0 to SATA 6Gb s Adapter 4 Plug in the AC adapter to an available AC power outlet to power on the USB 3 0 to SATA 6Gb s Adapter Driver Installation Windows will automatically detect and install the correct drivers for the USB 3 0 to SATA 6Gb s Adapter No additional driver installation is needed Note In order to get USB 3 0 performance make sure your USB3 0controllershave the correct drivers installed To Verify Windows Installation 1 Check Device Manger to verify installation For Windows 8 7 Right click Computer click Manage click Device Manager For Windows Vista Right click Computer click Manage click Continue click Device Manager For Windows XP Server 2003 Right click My Computer click Manage click Device Manager For Windows Server 2008 Server 2008 R2 Right click My Computer click Manage double click Diagnostics click Device Manager 2 For SATA drive Double clic
6. k Disk Drives Name and or model number of HDD USB Device should be displayed For SATA DVD CD ROM Double click DVD CD ROM Drives Name and or model number of DVD CD ROM should be displayed 3 Double click Universal Serial Bus controllers USB Mass Storage Device should be displayed Using the USB 3 0 to SATA 6Gb s Adapter Accessing SATA Drive or SATA DVD CD ROM Drive An additional drive icon will appear in Computer or My Computer when the USB 3 0 to SATA 6Gb s Adapter is plugged into a USB port The drive acts just like a conventional hard disk or SATA DVD CD ROM in your system Note For DVD and CD ROM drives the drive icon may not be displayed when no media is inserted Simply insert your media into the drive and wait a few moments for the drive icon to appear Disconnecting the USB 3 0 to SATA 6Gb s Adapter Use the Safely Remove Hardware icon to stop the USB 3 0 to SATA 6Gb s Adapter before disconnecting it from the computer Not following these instructions may result in data corruption data loss or damage to your SATA drive Follow the steps below for your Windows version Windows 8 7 Server 2008 R2 1 Verify that the LED is not flashing before proceeding 2 Click Show hidden icons click the Safely Remove Hardware and Eject Media icon located in the system tray by the system clock 3 Clickeither Eject USB Mass Storage Device or Eject DVD CD Drive 4 You can now unplug the USB 3 0
7. to SATA 6Gb s Adapter from the computer Windows Vista Server 2008 1 Verify that the LED is not flashing before proceeding 2 Click the Safely Remove Hardware icon located in the system tray by the system clock 3 Click Safely remove USB Mass Storage Device then click OK 4 You can now unplug the USB 3 0 to SATA 6Gb s Adapter from the computer Windows XP Server 2003 1 Verify that the LED is not flashing before proceeding 2 Double click the Safely Remove Hardware icon located in the system tray by the system clock 3 Highlight USB Mass Storage Device click Stop OK OK then click Close 4 You can now unplug the USB 3 0 to SATA 6Gb s Adapter from the computer Disconnecting SATA Hard Disk or DVD CD ROM Use the Safely Remove Hardware icon to stop the USB 3 0 to SATA 6Gb s Adapter first before disconnecting a SATA hard disk or SATA DVD CD ROM Technical Support and Warranty QUESTIONS SIIG s Online Support has answers Simply visit our web site at www siig com and click Support Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analyst will promptly respond SIIG offers a 2 year manufacturer warranty with this product This warranty covers the original purchaser and guarantees the product to be free of any defects in materials or workmanship for two 2
Download Pdf Manuals
Related Search