Spektrum SPMAR610
Contents
1. 4105 Fieldstone Rd Support All Champaign Illinois 61822 877 504 0233 other products USA Units 1 4 Ployters Rd United Horizon Hobby Staple Tye Harlow Essex 44 0 1279 641 097 Kingdom Limited CM18 7NS sales horizonhobby co uk United Kingdom Horizon Christian Junge StraBe 1 Germany Technischer 25337 Elmshorn 49 0 4121 2655 100 service horizonhobby de Service Germany France Horizon Hobby 11 Rue Georges Charpak 33 0 1 60 18 34 90 SAS 77127 Lieusaint France infofrance horizonhobby com TS Room 506 Wa 097 ChangstouRa anon com cn Shanghai China 200060 yom Customer Service Information County of Horizon Hobby Address Phone Number Email Address Purchase S bso Sd Champaign nas 0003984839 America 61822 USA y Units 1 4 Ployters Rd United Horizon Hobby Staple Tye Harlow Essex 44 0 1279 641 097 Kingdom Limited CM18 7NS sales horizonhobby co uk United Kingdom z Christian Junge Stra e 1 Horizon Hobby 49 0 4121 2655 100 Germany GmbH 25337 service horizonhobby de Germany France Horizon Hobby Rue Georges Charpak 33 0 1 60 18 34 90 SAS 77127 Lieusaint France infofrance horizonhobby com Room 506 oie gs E a Shanghai China 200060 RIT 15 FCC Information This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause2. system Following are the operational differences Brownout Detection Not Available on DSMX Receivers 05 2 receivers feature Brownout Detection that flashes the receivers LED if a power interruption occurs While DSMX receivers have QuickConnect technology and recover instantly from a power interruption the architecture of DSMX prevents Brownout Detection when operating in DSMX mode Flight Log Recording Fades Higher than DSM2 Note that DSMX moves through the band while DSM2 finds two quiet channels and remains on those channels Consequently because DSMX operates on uiet and noisy channels it s common to have more Antenna Fades than when sing DSM2 when used in busy 2 4GHz environments When taking flight log ata readings the Frames and Hold Data are important and should be used 5 a reference while Fades are insignificant due to the nature of frequency hifting A 10 minute flight will typically result in less than 50 Frame Losses nd no Holds Just How Good is DSMX In multiple tests 100 DSMX systems were operated simultaneously for extended periods of time During these tests each of the 100 systems was monitored in flight and on the ground In every test not a single case of RF link loss latency increase or control degradation was experienced or recorded 9 M QcQ Is DSMX Compatible with DSM2 Yes DSMX is fully compatible with all DSM2 hardware In fact many pilots may find the DSM2 equipment they have now
3. Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement decisions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting iability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you
4. harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation A CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2 400GHz to 2 4835GHz frequency range Compliance Information for the European Union Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2012110405 Product s SPM AR610 6 Channel Sport Aircraft Receiver Item Number s SPMAR610 Equipment class 1 The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European R amp TTE directive 1999 5 EC EN301 489 1 V1 7 1 2006 EN301 489 17 V1 3 2 2008 Signed for and on behalf of D WLL Horizon Hobby Inc Steven A Hall uae 5 U Executive Vice President and Chief Operating Officer International Operations and Risk Management Horizon Hobby Inc Instructions for Disposal of WEEE by Users the European Union 5 product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a desig
5. or the Spektrum Flight Log SPM9540 work well for this test Connect the voltmeter to an open channel port in the receiver and with the System on load the control surfaces apply pressure with your hand while monitoring the voltage at the receiver The voltage should remain above 4 8 volts even when all servos are heavily loaded CAUTION When charging Ni MH batteries make sure the battery fully charges Ni MH batteries charged with peak detection fast chargers have a tendency to false peak i e not fully charge which could lead to a crash QuickConnect Technology with Brownout Detection DSM2 Only Your AR610 features QuickConnect technology with Brownout Detection Should an interruption of power occur brownout the system will reconnect immediately when power is restored QuickConnect e The LED on the receiver will flash slowly indicating a power interruption brownout has occurred Brownouts can be caused by an inadequate power supply weak battery or regulator a loose connector bad switch inadequate BEC when using an electronic speed controller etc Brownouts occur when the receiver voltage drops below 3 5 volts This interrupts control as the servos and receiver require a minimum of 3 5 volts to operate How QuickConnect With Brownout Detection Works When the receiver voltage drops below 3 5 volts the system drops out ceases to operate e When power is restored the receiver immediately
6. 44 in x 1 05 in x 0 50 in Weight 9 g Input Voltage Range 3 5 9 6 Resolution 2048 Compatibility All DSM2 DSMX Aircraft Transmitters and Module Systems Receiver Installation For optimum RF link performance mount the antennas for best possible signal reception for the aircraft in all possible attitudes and positions Orient the antennas perpendicular to each other one vertical and one horizontal Mount the long antenna at least 2 inches away from and perpendicular to the short antenna using tape Do not use amplified Y harnesses or servo extensions with Spektrum equipment Use only standard non amplified Y harnesses or servo extensions When converting an existing model to Spektrum replace all amplfied Y harnesses and or servo extensions with conventional non amplified versions Connect the servo leads into the appropriate servo ports in the receiver noting the polarity of the servo connector Connecting the Leads 11004 2 PA miziim X 6CH SPORT RECEIVER ED 1 D L BIND DATA AUX1 Auxilary 1 port Bind Data port GEAR Gear port THRO Throttle port RUDD Rudder port AILE Aileron port ELEV Elevator port Binding Binding is the process of programming the receiver to recognize the GUID Globally Unique Identifier code of a single specific transmitter You must bind the AR610 receiver to your transmitter before it will operate 1
7. AR610 User Guide AR610 Bedienungsanleitung Guide de l utilisateur AR610 AR610 Guida dell utente NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND a little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury A WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this Product in a safe and respon
8. To bind an AR610 to a 05 2 05 transmitter insert the bind plug in the BATT BIND port on the receiver To bind an aircraft with an electronic speed controller that powers the receiver through the throttle channel ESC BEC insert the bind plug into the BATT BIND port in the receiver and the throttle lead into the THRO port 2 Power on the receiver The LED on the receiver will flash indicating the receiver is ready to be bound to the transmitter Shown using a separate receiver pack The battery can be connected to any open port except the Bind port Once the bind process is complete you can remove the bind plug and connect the battery to the Bind port Shown using an ESC BEC and flight pack 6 Follow the procedures of your specific transmitter to enter Bind Mode The system will connect within a few seconds Once connected the LED on the receiver will turn solid indicating the system is connected Remove the bind plug to prevent the system from entering bind mode the next time the power is turned on After you ve set up your model rebind the system to reset the failsafe AR610 Failsafe Prevents unintentional electric motor response on start up Establishes low throttle failsafe if the RF signal is lost Removes servo output pulses to all channels except the throttle channel during failsafe Failsafe position is stored via the throttle stick position on th
9. attempts to reconnect to the last two frequencies it was connected to f the two frequencies are present the transmitter was left on the system reconnects typically in about 4 100 of a second QuickConnect with Brownout Detection is designed to allow you to fly safely through most short duration power interruptions However you must correct the cause of these interruptions before your next flight to prevent a crash CAUTION If a brownout occurs in flight determine the cause of the brownout and correct it before attempting to fly again Flight Log SPM9540 Optional The Flight Log is compatible with the AR610 The Flight Log displays overall RF link performance as well as the individual internal and external receiver link data Additionally it also displays receiver voltage 10 Using the Flight Log After a flight and before turning off the receiver or transmitter connect the Flight Log to the Data port on the AR610 The screen will automatically display voltage e g 6v2 6 2 volts When the voltage reaches 4 8 volts or less the screen will flash indicating low voltage Press the button to display the following information A Antenna fades on the internal antenna R Not used B Not used F Frame loss L Antenna fades on the external antenna H Holds Antenna fades represents the loss of a bit of information on that specific antenna Typically it s normal to have as many as 50 to 100 antenna fades during a flig
10. both transmitter and receiver are DSMX enabled NOTICE DSMX upgraded DX5e and DX6i transmitters are compatible with all DSMX receivers except the high speed DSM2 receivers like the AR7600 AR9000 etc When using a high speed DSM2 receiver with the DX5e or DX6i it s necessary to manually put these transmitters into DSM2 mode See the Spektrum website for details on DX5e DX6i DSM2 mode for details Transmitter Receiver Compatibility Transmitter ZWSG 01 XL 195 R500 R600 R6100 R6110 e R6200 R6255 R6300 R6400 ALL R7000 2 AR400 AR600 AR610 AR6115 e AR6210 AR6255 AR6310 AR6410 ALL AR7010 AR7110 R AR7200BX AR7610 R7100 R R7600 R8000 R9000 R9100 R9200 R9300 R12000 R12100 AR8000 AR9010 AR9020 AR9110 AR9210 AR9310 AR10000 AR12010 AR12020 AR12110 AR12120 19119994 AR610 User Guide The AR610 features DSM2 DSMX technology and is compatible with all Spektrum and JR aircraft radios that support D5M2 DSMX technology NOTICE The AR610 receiver is not compatible with the DX6 parkflyer radio system Features e Full Range e QuickConnect with Brownout Detection Brownout Detection only in DSM2 mode Resolution 2048 e Flight Log and Telemetry Compatible Specifications Type Full Range Sport Receiver Channels 6 Modulation 05 2 05 Dimension LxWxH 36 6mm x 26 7mm x 12 7mm 1
11. ce nearest you Contact information is listed in the Warranty section some aircraft when the model is placed on the ground the antenna s can be within inches of the ground Close proximity of the antenna s to the ground can reduce the effectiveness of the range check This is called pulling If you experience issues during the range check restrain the model on a non conductive stand or table up to 2ft 60cm above the ground then range check the system again Receiver Power System Requirements Inadequate power systems that do not provide the necessary minimum voltage to the receiver during flight have become the number one cause of in flight failures Some of the power system components that affect the ability to properly deliver adequate power include Receiver battery pack number of cells capacity cell type state of charge The ESC s capability to deliver current to the receiver in electric aircraft e The switch harness battery leads servo leads regulators etc The AR610 has a minimum operational voltage of 3 5 volts it is high recommended the power system be tested per the guidelines below Recommended Power System Test Guidelines If you are using a questionable power system e g a small or old battery an ESC that may not have a BEC that will support high current draw etc perform the following test with a voltmeter The Hangar 9 Digital Servo amp Rx Current Meter HAN172
12. e transmitter during binding HOW AR610 FAILSAFE WORKS Receiver Power Only When the receiver only is turned on no transmitter signal is present the throttle channel has no output This prevents arming of the electronic speed control Some analog servos may coast slightly even though no signal is present This is normal All other channels will have no signal output After Connection When the transmitter is turned on and after the receiver connects to the transmitter normal control of all channels return f a signal loss occurs the AR610 failsafe drives the throttle servo to its preset failsafe position low throttle that was set during binding e other channels receive no output pulses commands and are not active during failsafe Range Testing Before each flying session and especially with a new model it is important to perform a range check All Spektrum aircraft transmitters incorporate a range testing system which when activated reduces the output power 5 ra M TUR 30 paces 90 feet 28 meters HI 1 With the model restrained on the ground stand 30 paces approx 90 feet 28 meters away from the model 2 Face the model with the transmitter in your normal flying position and place your transmitter into range check mode 3 You should have total control of the model at 30 paces 90 feet 28 meters 4 If control issues exist call a Horizon Product Support offi
13. have come to embrace 2 4 as the way to fly Spektrum leads the way yet again with DSMX the world s first wideband frequency agile 2 4GHz signal protocol How Does DSMX Work It s a crowded 2 4GHz world out there and every 2 4GHz system faces the same challenges DSMX better equips you for these challenges by combining the superior data capacity and interference resistance of a wideband signal like that used in DSM2 with the agility of frequency shifts Compared to the wideband signal of DSMX the narrow band signal of other frequency hopping 2 4 transmitters is more likely to suffer data loss in the event of on channel interference Think of it as a river vs a stream It takes more interference to dam a river than it does a stream As more and more 2 4 transmitters vie for the same number of available channels there is more interference and more of a risk for data loss By adding the agility of frequency shifts to the superior interference resistance of a wideband signal DSMKX is far less likely to suffer significant data loss from on channel interference The result is quicker connection times and superior response in even the most crowded 2 4GHz environment DSMX Operational Differences DSMX transmitters and receivers function nearly identically to Spektrum DSM2 systems Binding setting the failsafe recording flight log data as well as general use of the system is no different than using any current Spektrum
14. ht If any single antenna experiences over 500 fades in a single flight the antenna should be repositioned in the aircraft to optimize the RF link Frame loss represents simultaneous antenna fades on all attached receivers If the RF link is performing optimally frame losses per flight should be less than 20 A hold occurs when 45 consecutive frame losses occur This takes about one second If a hold occurs during a flight it s important to evaluate the system move the antennas to different locations and or check to ensure the transmitter and receivers are all working correctly A servo extension can be used to allow the Flight Log to be connected more conveniently On some models the Flight Log can be connected attached and left on the model using double sided tape Mounting the Flight Log conveniently to the side frame is common with helicopters ModelMatch Some Spektrum and JR transmitters have ModelMatch technology which prevents the possibility of operating a model using the wrong model memory potentially preventing a crash With ModelMatch each model memory has its own unique code GUID and during the binding process the code is programmed into the receiver Later when the system is turned on the receiver will only connect to the transmitter if the corresponding model memory is programmed onscreen If at any time you turn on the system and it fails to connect check to be sure the correct m
15. ing the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of gt hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and Conditions found on our website http www horizonhobby com content _service center_render service center ATTENTION Horizon service is limited to Product compliant in the country of use and ownership If received a non compliant Product will not be serviced Further the sender will be responsible for arranging return shipment of the un serviced Product through a carrier of the sender s choice and at the sender s expense Horizon will hold non compliant Product for a period of 60 days from notification after which it will be discarded 14 Warranty and Service Contact Information EXT Horizon Hobby Address Phone Number Email Address Purchase ORA 4105 Fieldstone Rd 877 504 0233 Service Center Electronics and Champaign Illinois 61822 Online Repair Request United USA visit www horizonhobby com service States of engines America Horizon Product
16. is all they will ever need Even if a new DSMX transmitter eventually comes along that they really want all the DSM2 receivers they have now will work with it It is important to note however that while DSMX is compatible with DSM2 the only way to experience the full benefits of DSMX in a busy 2 4 environment is by pairing a DSMX transmitter with a DSMX receiver Are DSM2 Transmitters Eligible for a DSMX Add on Yes DX8 owners can simply download Spektrum AirWare software from spektrumrc com and update the firmware using their SD card All DSM2 transmitters except the DX5e are eligible for the add on by going to https community spektrumrc com for details DSM2 receivers and transmitter modules are not eligible for the DSMX add on Does DSMX have ModelMatch and ServoSync Technology Yes DSMX will provide you with these and other exclusive Spektrum advantages you already enjoy with DSM2 Want to know more about DSMX Visit spektrumrc com for complete details on this as well as the many other reasons Spektrum is the leader in 2 4 NOTICE DSMX receivers are not compatible with DSM2 remote receivers and DSM2 receivers are not compatible with DSMX remote receivers DSMX transmitters are compatible with all DSM2 and DSMX receivers and will operate in the mode noted below e DSM transmitters are compatible with all DSM2 and DSMX receivers and will operate in the mode noted below e DSMX technology is active only when
17. istance from metal objects and the receiver itself be power up and try again Ore you 3 Q Is it true that DSM systems are less tolerant of low voltage A All DSM receivers require at least 3 5V to operate normal cease to operate below 3 8V Using multiple high voltage inadequate power supply can allow voltage to momentari ly Mos Servos y drop Servos with an below 3 5V This will cause the receiver to brown out and reconnect See the QuickConnect with Brownout Detection section for more i nforma 4 Q Sometimes when power on my DSM system I notice the receiver won t connect and it needs to be rebound transmitter Can this happen in flight to the ion A No A DSM receiver cannot be unbound from its transmitter without specific action by the user 5 Q How important is it that test my system using a Spektrum Flight Log A All 2 4GHz signals not just DSM are affected by proximity to conductive materials such as carbon fiber or metal Few RTF and ARF sport airplanes or helicopters use enough of these kinds of materials for it to be an issue If however you re flying a sophisticated model that uses a lot of conductive materials in its construction a Flight Log can be helpful The information it collects when you fly will help you determine the optimum location for your receiver s so you can minimize the effects of these materials on your signal performance For more details
18. izonhobby com content _service center_render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitt
19. may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of purchase cannot provide warranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry or call 877 504 0233 toll free to speak to a Product Support representative 13 Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www hor
20. nated collection point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product 16 SPERTRUNTI 37275 Created 3 13 2013 Horizon Hobby Inc DSM DSM2 DSMX ModelMatch QuickConnect SmartSafe ServoSync JR E flite and Hangar 9 are trademarks or registered trademarks of Horizon Hobby Inc The Spektrum trade mark is used with permission of Bachmann Industries Inc Patents Pending
21. odel memory is selected in the transmitter Please note that the Spektrum Aircraft Modules do not have ModelMatch technology Frequently Asked Questions on Spektrum 2 4GHz 1 Q After I ve bound the receiver to my transmitter which do turn on first when want to fly A Either one Every DSM 2 4GHz transmitter has a GUID Globally Unique Identifier code imbedded in its signal When you bind a DSM receiver to your transmitter this GUID code is stored in the receiver If you turn the receiver on before the transmitter you don t have to worry about it responding to another transmitter The receiver will go into failsafe mode while it waits for a signal from the transmitter with the same GUID code 11 it has stored See the Receiver Power Only section for more information If a DSM transmitter is turned on first you can expect it to connect within 6 seconds of powering on the receiver 2 Q Sometimes the system takes longer to connect or doesn t connect at all Why A In order for a DSM system to connect the receiver must receive a large number of uninterrupted signal packets from the transmitter This process takes just a few seconds but if the transmitter is too close to the receiver within 4 feet or near reflective material metal objects carbon fiber material etc it may detect its own reflected 2 4GHz energy as noise This can delay or prevent connection If this happens make sure you are a sufficient d
22. on the Flight Log and how it works visit SpektrumRC com 1 Year Limited Warranty What this Warranty Covers Horizon Hobby Inc Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in materials and workmanship for a period of 1 years from the date of purchase What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Horizon Hobby authorized service center v Product not purchased from an authorized Horizon dealer or vi Product not compliant with applicable technical regulations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL MPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be hat Horizon will at its option either i service or ii replace any Product determined by
23. sible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not attempt disassembly use with incompatible components or augment product in any way without the approval of Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy A WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon Hobby Inc authorized dealer to ensure authentic high quality Spektrum product Horizon Hobby Inc disclaims all support and warranty with regards but not limited to compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum NOTICE This product is only intended for use with unmanned hobby grade remote controlled vehicles and aircraft Horizon Hobby disclaims all liability outside of the intended purpose and will not provide warranty service related thereto WARRANTY REGISTRATION Visit www spektrumrc com registration today to register your product 2 EM DSMX Spektrum launched the 2 4GHz RC revolution with its DSM2 technology Since then millions of hobbyists the world over
Download Pdf Manuals
Related Search