Blade 700 X Pro
Contents
1. The motor is not connected to the ESC or the motor Connect the motor wires to the ESC and check motor wires for dam wires are damaged age Flight battery charge is too low Replace or recharge flight battery Throttle channel is reversed Reverse the throttle channel on the transmitter Flight battery has low voltage Fully charge the flight battery Helicopter power is lacking Flight battery is old or damaged Replace the flight battery Fully charge the flight battery allowing the charger time to balance the cells Transmitter settings are not correct Check throttle and pitch curve settings and pitch control direction Flight battery has low voltage Fully charge the flight battery Install the main rotor blades with the thicker side as the leading edge Flight battery cells are unbalanced Helicopter will not lift off Main rotor blades are installed backwards Make sure the rudder control and the rudder sensor are operating in Rudder control and or sensor direction reversed gan the correct direction Tail servo is damaged Check the rudder servo for damage and replace if necessary The helicopter tail spins out of Tail drive gears are damaged Replace damaged gears control Check the rudder control arm for adequate travel and adjust if nec In ate control arm throw adequ essary Ensure the tail boom and tail gear box are fully seated Confirm tail Torque tube is not fully engaged in tail gears pushr2. O Brass Spacer x2 e The stepped sides of the washers should face the radial bearings e Do not over tighten The follower arms should move freely Og TO We Head Assembly cont d Step H6 parts H6 M3 X 50 Control Rod x2 M3 Ball Link S Pushrod lengths 67mm tte 50 Swash to blade grip link x2 QNO WM S 2 707 _ SS ii 9 NP 4 Anti Rotation Pin WIL Control Ball x7 Frame Assembly F NOTICE Before assembly plan your wire routing for the servos At any point where the servo wire is going to pass through or cross the frame plates use sandpaper to round the edge of the frame plate to prevent the wire from chafing M3 X 8 Cap Head Bolt x20 Washer M3 x4 e At this stage of the assembly do not tighten the bearing block screws e f desired the swash servos may be installed at this step before the bearing blocks are installed into the frame Please see step F6 for servo installation parts and procedure Step F2 parts bag F3 MS M3 X 14 Cap Head Bolt x4 Washer M3 x4 Frame Assembly cont d Step F3 parts bag F4 One Way Sleeve Ei SST M3 X 6 Button Head Bolts x6 ses z ID e Slide the mainshaft into position then tighten all the frame screws e A 5mm or 1mm shim may be added above the collar if needed al Step F4 Step F4 parts ba
3. SPEKTRUM DSMX CONTROL FLYBARLESS TECHNOLOGY Instruction Manual gt amp Bedienungsanleitung puts Manuel d utilisation Manuale di Istruzioni NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product The purpose of safety symbols is to atttract your attention to possible dangers The safety symbols and their explanations deserve your careful attention and understanding The safety warnings do not by themselves eliminate any danger The instructions or warnings they give are not substitutes for proper accident prevention measures NOTICE Procedures which if not properly followed create a possibility of physical property damage AND a little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage serious injury or death OR create a high probability of superficial injury Safety Alert Indicates warning or caution Attention is required in order to
4. Repeat Steps 1 through 3 until both blades are moving in the same plane Adjusting the Rudder Gyro Gain e f the tail wags or oscillates lower the gain on the gyro e f the tail is drifting while hovering increase the gain on the gyro On your transmitter s gyro menu decrease the gyro gain values a small amount On your transmitter increase the gyro gain values a small amount at a time until at a time until the helicopter is stable within a particular flight mode the tail starts to wag oscillate Afterwards reduce the gain until the tail stops wagging oscillating within a particular flight mode Post Flight Inspection and Maintenance Checklist M Make sure the plastic ball link holds the control ball but Make sure there is no damage to rotor blades and other Ball Links is not tight binding on the ball When a link is too loose parts which move at high speed Damage to these parts on the ball it can separate from the ball during flight and includes cracks burrs chips or scratches Replace dam cause a crash Replace worn ball links before they fail aged parts before flying Make sure the battery is not connected before cleaning Remove dust and debris with a soft brush a dry lint free Make sure the AR7200BX is securely attached to the frame Replace the double sided tape when necessary The NS helicopter will crash if the AR7200BX separates from the Bearings Replace bearings when they become notchy sticky in helicopter
5. i elcome to the world of Blade Pro Series helicopter performance Over two decades of flying and design experience has gone into the development of the B ade 700 X Every part down to the nuts and bolts has been chosen or designed with one goal in mind giving you a 700 size 3D machine that is second to none Before you tear into the contents of this box however you must review this manual It s been written and designed to make assembling the Blade 700 X one of the most enjoyable hassle free building experiences you ll ever have Every step is clearly illustrated and shows what parts are needed to complete it Table of Contents Tools Needed to Complete akut egen 4 Required NEMS cits wasinceaeoscecnenmsawendnmiaceieandannwabesasisanmedaceadaniedtianadansnenedadsuransedsaneaccs 4 O a an 4 Assembly Guide sese 4 Head Assembly dn EE 5 ice yy JA PR 8 Tail Assembly 1 eee 14 ESC and Battery Tray Assembly 18 Main Rotor Installation 20 Programming Your Transmittler a tasses stores 20 Throttle le E 20 AR7200BX Parameter Menu Tips I asas 20 Motor Direction TES LLL LIL A aa aga aa ak a lu MU DU EPIS 21 Low Voltage KEE 21 lf this is your first helicopter building experience there are a few things you might want to get before you start unpacking parts Many builders prefer to lay out a towel
6. 1 1 2009 EN55022 2010 AC 2011 EN55024 2010 C Signed for and on behalf of Robert Peak Horizon Hobby Inc Chief Financial Officer Champaign IL USA Horizon Hobby Inc July 21 2013 Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equip ment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the en vironment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product Exploded View Battery Tray Explosionszeichnung Akkuhalter Vue clat e Platine de fixation de batterie Vista esplosa Supporto batteria 98 Exploded View Head Tailcase Explosionszeichnung Rotorkopf Heckrotorgeh use Vue clat e T te et Anticouple Vista esplosa Testa Scatola di coda Exploded View Frame Assembly Explosionszeichnung Chassis Vue clat e Assemblage du chassis Vista esplosa Gruppo telaio Exploded View Tailboom Assembly Expl
7. 14 Button Head Bolt x2 eg OR M3 X 14 Cap Head Bolt x2 Canopy Spacer x2 C Rubber Canopy Standoff x2 e The battery tray has forward and rear mounting locations to accommodate your equipment selection Most of the equipment we ve used has worked best with the rear mounting location to achieve the correct center of gravity Install both battery support posts in either the front or rear location The front support post uses a button head screw for the forward position and a cap head screw for the rear location to best fit the canopy Battery Tray parts bag B1 M3 X 8 Counter Sunk Screw x8 Lo M4 X 12 Cap Head Bolt x2 M2 8 Cap Head Screw x2 O Spacer 4 X 5 X 3 x2 ESC and Battery Tray Assembly cont d Loop material Hook material Hook and loop straps Main Rotor Installation Main Rotor parts bag H3 M5 X 28 Cap Head x2 Shoulder Bolt M5 Lock Nut x2 Q e EE ch e The rotor blades should be tight enough to hold their position if you hold the helicopter sideways but loose enough to swing freely if you move the helicopter and stop abruptly b c Programming Your Transmitter Refer to your FBL controller and transmitter manuals for proper setup Programming instructions for the E flite 100 Amp HV brushless ESC EFLA2100 included with the combo kit can be found online at www horizonhobby com The EFLA2100 is preprogrammed at the f
8. Light Viscosity Lube CE Loosely Tighten Apply NO Threadlock CA Apply Synthetic Grease Fully Tighten Bd Apply MEDIUM CA Repeat Multiple Times pa _ y Head Assembly H Smaller inner diameter I D Larger inner diameter I D WARNING Any time you loosen the spin dle bolts completely clean the bolts with denatured alcohol and ensure you have removed any residual oil When putting bolts back on apply medium strength threadlock to the bolts and allow time for the threadlock about 4 to 6 hours to dry before attempting to fly your helicopter Step H1 parts bags H1 and H2 M4 X 25 Cap Head Shoulder Bolt x2 M4 Locknut X2 Step H2 parts bags H1 and H2 Spindle Sleeve Damper X2 e Clean the threads in the spindle thoroughly with alcohol before installation Step H3 parts bag H3 M4 X 12 Cap Head Bolt x2 M4 X 10 X 2 Washer x2 Thrust Bearing 8 X 16 X 5 x2 Washer 8 X 12 5 X 5 x2 Radial Bearing 8 X 16 X 5 x2 Stepped Washer 8 X 16 X 1 x2 e The stepped sides of the washers should face the radial bearings EN Head Assembly cont d Step H4 parts bag H4 X 14 Button Head Bolt x2 RR M3 X 12 Button Head Bott x2 daa CM Control Ball x2 e Loosely install bolts A and B before tightening Step H5 parts bag H5 M3x12 Head Bolt x2 O Washer 3 X 4 X 5 x4 Radial Bearing 3 X 6 X 2 5 x4
9. and objects Your first flights should be outdoors in low wind conditions Always stay at least 45 feet 13 meters away from the helicopter when it is flying Do not attempt to fly the Blade 700 X indoors CAUTION The Blade 700 X is intended for pilots with experience flying aerobatic collective pitch helicopters The Blade 700 X is more responsive than other Blade helicopters If you are not an experienced 3D or collective pitch helicopter pilot do not attempt to fly this product Takeoff Gradually increase the throttle allowing the rotors time to come up to speed CAUTION Do not give any aileron elevator or rudder commands before the helicopter lifts off Any control inputs prior to liftoff could cause a crash The helicopter will lift off the ground when the rotor head reaches a suitable speed and you apply collective pitch Once airborne establish a low level hover to verify everything is functioning properly DO NOT use trim to assist in holding the Blade 700X in a desired position The AR7200BX Flybarless Stabilization System renders trim unnecessary by working to keep the helicopter in whatever attitude you command with the control sticks Flying This aircraft is extremely sensitive to control inputs We recommend you fly at low rate settings for the first few flights until you are familiar with its response For pilots new to collective pitch helicopters familiarize yourself with your Blade 700 X in normal mode and at low
10. cont d Step F9 parts bag F7 Step F10 parts bag F8 Hexagonal Posts x6 Jack Shaft Radial Bearing 5 X 10 X 4 x2 x2 M3 X 4 Set Screw 12 EN Frame Assembly ont d d amm s a x4 M3 X 8 Cap Head Bolt x12 M3 X 8 Cap Head Bolt Step F11 parts bag F8 Step F12 parts bag F9 AR7200BX Alignment A A DR ATEN AL r 4 NE 380 ii eem a oo amas PE 2 2 NS IAN J gs Lo Y ZA 2 SK nV di AS XS DI E 9 a SA S sw Je di DYN ZUN RD 27 v ZA gt N Double sided EN 13 Tail Assembly T Step T1 parts bag T1 LU M3 X 6 Button Head Bolt x2 Step T2 parts bag T2 M3 X 4 Set Screw Gear Pin Step T3 parts bag T3 Small inner diameter race M3 X 8 Cap Head Bot Ga 4 Bearing cage m g cag Control Ball x2 e 2 Lp P Large inner diameter race ily M4 X 3 Set Screw tj A Washer M3 1 X 7 X 5 x2 B Washer M5 X 8 X 5 x2 C C Washer M8 X 10 X 5 x2 IL Il Radial Bearing 5 X 10 X 4 4 Thrust Bearing 5 X 10 X 4 x2 Tail assembly cont d Step T4 parts bag T4 X 6 Button Head Bott x2 IR Bell Crank Bolt x2 Contro Bal Flanged Bearing M3 X 6 X 2 5 x2 Washer M3 X 4 X 5 x2 Al CT Lee A Step T5 parts bag T3 M3 X 16 Ca
11. from many sources outside your control Interference can cause momentary loss of control e Always ensure you fully understand the controls on your transmitter and how they affect the movement of the helicopter e Always operate your model outdoors in large open spaces away from full size vehicles traffic and people to avoid collisions or injury e Always carefully follow the manufacturer s directions and warnings for any related equipment i e chargers rechargeable battery packs etc e Always keep the product related chemicals small parts and electrical components out of the reach of children e Always keep children out of the vicinity of this product at all times e Always store this product well out of the reach of children e Always keep hair secured above your shoulders so it cannot get caught in the blades e Always avoid water exposure to all equipment not specifically designed and protected for this purpose Moisture causes damage to electronics e Never maintain and operate this product at night in rain or in inclement weather e Always ensure all fasteners are secure before use e Always store product in a dry temperate secure location e Do not touch the motor as it can become extremely hot during use e Do not fly this helicopter indoors e Always ensure the failsafe is properly set before flying Do not exclusively rely on the safety mechanisms built into your transmitter and receiver e Always ensure you understand the product and how
12. rate 3 Connect the Li Po battery to the ESC 4 Turn TH HOLD OFF Slowly increase the throttle until the drive train begins to turn The main blades spin clockwise when viewing the helicopter from the top The tail rotor blades spin counterclockwise when viewing the helicopter from the right hand side NOTICE If the drive train does not turn with the motor or spins counterclockwise turn TH HOLD ON Disconnect the battery from the helicopter and reverse any two motor wire connections to the ESC and repeat the motor control test Crash damage and battery damage are not covered under warranty Always disconnect and remove the Li Po battery from the aircraft after each flight Charge your Li Po battery to about half capacity before storage During storage make sure battery charge does not fall below 3V per cell A connected battery will result in trickle discharge e Always keep moving parts clean e Always keep parts dry e Always let parts cool after use before touching e Always remove batteries after use e Always have a first aid kit with you e Always have an appropriate fire extinguisher with you e Never operate aircraft with damaged wiring e Never touch moving parts CAUTION Always fly the helicopter with your back to the sun and wind to prevent loss of flight control Landing Establish a low level hover Deliberately lower the throttle until the helicopter lands Make only small control corrections during this ti
13. 00 X BLH5748 Tail Pushrod Set 2 700 X Blade 700 X Gest nge a X Set de commande d anticouple set comandi coda 700 X D BLH5749 Tail Pushrod Guide Set 700 X Blade 700 X Gestangefuhrung Heck UR de commande Set guida comandi coda 700 X 49 BLH5750 Horizontal Fin Mount 700 X Blade 700 X Halter f Heckfinne 700 X Support de stabilisateur Supporto impennaggio orizzontale 700 X NL 102 Part English Deutsch Francais Italiano BLH5751 Fin Set 700 X Blade 700 X Finnenset 700 X Set d empennages Set impennaggio 700 X BLH5752 Tail Rotor Pitch Lever Set 700 X Blade 700 X Heckrotorpitchhebelset 700 X Levier de pas d anticouple Set leve passo rotore coda 700 X 52 BLH5753 i pitch Control Slider Set Blade 700 X Schiebeh lse Heckrotor Set 700 X Coulisseau d anticouple Set cursore controllo passo coda 700 X BLH5760 Battery Tray Mounting Posts 700 X Blade 700 X Stutzen Akkuhalter fee Supports de platine porte d montaggio supporto batteria eo BLH5761 SEN Tray Locking Mount Blade 700 X Akkuverschluss s Support de verrouillage de la Aggancio supporto batteria 700 X 64 BLH5765 Pinion 157 700X Blade700XRize 157 700 157 Pigmnef T700X 66 BLH5767 12x24x6mm Radial Bearing Blade 700 X 12x24x6mm Radiallager Roulement 12x24x6mm 224x6mm Cuscinetto radiale _68 BLH5769 5x10x4mm Thrust Bearing Blade 700 X 5x10x4mm Druckager But e billes 5x10x4mm 5
14. Chassis 1 Links o Rechts ea rane de chassis en carbone CE Telaio principale 1 L o R 700 X BLH5723 Upper Bearing Block 700 X Blade 700 X Lagerblock oben 700 X Palier sup rieur Cuscinetto superiore blocco 700 X BLH5724 Bottom Servo Mount 700 X Blade 700 X Servohalter unten 700 X Support inf rieur de servo Supporto inferiore servo 700 X BLH5726 Lower Bearing Block 700 X Blade 700 X Lagerblock unten 700 X Palier inf rieur Cuscinetto inferiore blocco 700 X BLH5727 Servo Screw Set 700 X Blade 700 X Servoschraubenset 700 X Set de vis de servo Set viti servo 700 X BLH5728 ESC Mounting Tray 700 X Blade 700 X Halter f Regler 700 X Platine de fixation de contr leur Supporto ESC 700 X BLH5729 Landing Gear Mounts 700 X Blade 700 X Kufenhalter 700 X Fixations de train d atterrissage Supporti carrello 700 X BLH5730 Landing Gear Set 700 X Blade 700 X Kufengestell 700 X Train d atterrissage set carrello 700 X BLH5731 Ball Link Set 700 X Blade 700 X Kugelkopfset 700 X Set de rotules Set sfere comandi 700 X BLH5732 Anti Rotation Bracket 700 X Blade 700 X Taumelscheibenf hrung 700 X Guide anti rotation Staffa anti rotazione 700 X BLH5733 Motor Mount 700 X Blade 700 X Motorhalter 700 X Support moteur Supporto motore 700 X BLH5734 Pinion Support 700 X Blade 700 X Ritzelhalter 700 X Support de pignon Supporto pignone 700 X BLH5735 FBL Unit Mount 700 X Blade 700 X FBL Einheit Halter Aybar oe de mode de cont
15. ODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be that Horizon will at its option either i service or il replace any Product determined by Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement decisions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Pr
16. actory Please use the throttle curves given below for the factory default programming Throttle Curve NORM 0 25 25 25 25 ST 1 15 15 15 15 15 ST 2 100 100 100 100 100 Throttle Hold When you move the throttle hold switch to the ON position the helicopter motor You should also turn throttle hold ON to minimize damage if the helicopter is out turns off You will still have control of the helicopter cyclic and rudder commands of control or in danger of crashing The blades spin if throttle hold is OFF For safety turn throttle hold ON any time See your transmitter manual for more information on programming throttle hold you need to touch the helicopter or check the direction controls E flite 100 Amp ESC Throttle Hold Settings Throttle off Throttle off no bailout with bailout 2 Throttle on Throttle Hold Setting AR7200BX Parameter Menu Tips Refer to the Spektrum AR7200BX manual to fine tune the Blade 700 X to your If you would like to have the cyclic behavior to feel more linear OR more like flying and control style via the AR7200BX parameter menu a flybarred helicopter increase the cyclic response by adjusting parameter G If you would like to change the control behavior of the flybarless system to a default is normal pre defined behavior in the AR7200BX adjust parameter B default behavior is Refer to the Spektrum AR7200BX manual for specific details on each transmitter parameter w
17. avoid serious personal injury WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product for advanced helicopter pilots with previous experience in the operation of CCPM helicopters Cyclic Collective Pitch Mixing or Collective Pitch Helicopter such as the Blade SR Blade mCP X or Blade 300 X and previous kit building experience such as the Blade 550 X or Blade 600 X It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation For advanced fliers ages 14 and above This is not a toy General Safety Precautions and Warnings This model is controlled by a radio signal subject to interference
18. e d Motor Direction Test Place the helicopter outdoors on a clean flat and level surface concrete or asphalt free of obstructions Always stay clear of moving rotor blades 1 Power on the transmitter Make sure TH HOLD is ON and the flight mode switch is in the normal position WARNING The motor will spin when throttle is increased and TH HOLD is OFF 2 Lower the throttle completely WARNING Stay at least 45 feet 13 meters away from the helicopter when the motor is running Low Voltage Cutoff LVC Low voltage cutoff LVC protects the Li Po battery from overdischarge in flight and activates when the battery reaches 3V per cell under load Set your transmitter timer for 4 minutes and land when the timer expires Repeatedly flying to LVC will damage the flight battery and require you to replace the battery Flight Guidelines and Warnings e Always keep aircraft in sight and under control e Always keep people and pets at least 45 feet 13 meters away when the battery is connected e Keep children out of the vicinity of this product at all times e Always turn on throttle hold at rotor strike e Always use fullly charged batteries e Always keep transmitter powered on while aircraft is powered e Always remove batteries before disassembly Flying Your 700 A Consult local laws and ordinances before choosing a location to fly your aircraft Select a large open area away from people
19. e at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon for service you are agreeing to Horizon s Terms and Conditions found on our website http www horizonhobby com content service center render service center ATTENTION Horizon service is limited to Product compliant in the country of use and ownership If received a non compliant Product will not be serviced Further the sender will be responsible for arranging return shipment of the un serviced Product through a carrier of the sender s choice and at the sender s expense Horizon will hold non compliant Product for a period of 60 days from notification after which it will be discarded 24 Warranty and Service Contact Information Country of Purchase Horizon Hobby Contact Information Add
20. frame places when turning or draggy Make sure wiring does not block moving parts Replace Make sure the gears are all in good condition Watch for damaged wiring and loose connectors chipped teeth or excessive wear White dust around gears is an indication of excess wear Replace damaged gears Make sure there are no loose screws other fasteners or before flying connectors Do not over tighten metal screws in plastic parts Tighten screw so parts are mated together then turn screw only 1 8th of a turn more AR7200BX Fine tuning and Adjustment Observed Behavior Suggested Adjustment Cyclic response is too slow or too fast Adjust end points to fit your flying style Refer to your transmitter instruction manual for more information Adjust the control behavior parameter in the AR7200BX to fit your flying style Control inputs feel delayed Increase Dial 2 on the AR7200BX The helicopter seems to overshoot control input and then return Decrease Dial 2 on the AR7200BX The helicopter tail stops too abruptly Decrease Dial 3 on the AR7200BX The helicopter tail does not stop precisely Increase the rudder gain in your transmitter Increase Dial 3 on the AR7200BX Adjust the rudder heading lock gain parameter in the AR7200BX M M Blade 700 X Troubleshooting Guide Problem Possible Cause Solution The helicopter was moved during initialization Lay the helicopter on its side during initialization if windy AR7200BX will not initial
21. g F4 Frame side Sr M4 X 27 Cap Head Shoulder Bolt clarity Push down on the main cen gear and up on the collar while tightening the collar WI M3 X 6 Low Cap Head Bolt x4 bolts R p M SS er maa na a oO O U U ami N Come Frame Assembly ont d Step F5 parts bag F5 Step F5 Head assembly M4 X 40 Cap Head Shoulder Bolt x3 removed for clarity WEN 75 C b M3 Washer 4 UD M4 X 4 Set Screw x2 N Le NS Pinion Helical Mod 1 13T 6mm Step F6 parts bag F6 M3 X 8 Cap Head Bolt x3 s q o Y B M3 X 10 Cap Head Bolt x12 eg M3 Washer x12 NIN S3 Ap S aS LEA G _ Ve Ng A A SIONI N AUS 2793 Na KG c wo ll _ NM M2 X 12 Button Head Bolt x3 I M2 Nut x3 Servo Control Ball X3 Servo Horn X3 M3 X 55 Control Rod x3 Frame Assembly ont d Step F6 contd Elevator servo MU E pi D 9 TR A d o N Step F7 parts bag F6 N WY gt LS Z 4 AN Pos MMM 113 X 16 Cap Head Bolt x4 H M3 Washer x4 Servo Spacer x2 Tail Servo Nut x2 N N N M QOO N M M M N N L AB n M3 X 8 Cap Head Bolt x4 Frame Assembly
22. ize The transmitter is powered off Power on the transmitter Center elevator aileron and rudder controls Make sure the throttle is at idle Power off transmitter move transmitter a larger distance from air Transmitter is too near aircraft during binding process craft disconnect and reconnect flight battery to aircraft and follow LED on receiver flashes rapidly and binding instructions during binding was powered on ject wireless source or another transmitter again transmitter and connecting flight battery to aircraft aircraft LED on receiver flashes rapidly and Mode lMatch radios only connect flight battery to aircraft aircraft will not respond to transmit Flight battery transmitter battery charge is too low Replace recharge batteries ter after binding Transmitter may have been bound to a different model l or with a different DSM Protocol Select the right transmitter or bind to the new one Aircraft or transmitter is too close to large metal ob Move aircraft and transmitter to another location and attempt con ject wireless source or another transmitter necting again Throttle not at idle and or throttle trim is too high Lower the throttle stick and lower the throttle trim The transmitter is not in normal mode or throttle hold is on Controls are not centered Make sure the transmitter is in normal mode and throttle hold is off Helicopter will not respond to the throttle but responds to other con trols
23. me to avoid rotor blade strikes or other damage When the helicopter is in stunt mode e The rotor head speed is constant e The main rotor will increase negative pitch as the throttle collective stick is moved from the middle stick position to the low stick position Negative pitch allows the helicopter to fly upside down and perform aerobatics Change between stunt and normal modes in a hover with the throttle near the hovering stick position The helicopter may go up or down when you change between modes due to the difference in the throttle and pitch curves NOTICE To minimize damage always activate throttle hold in preparation for or during a crash WARNING Only use Blade 700 X approved carbon fiber main blades Do not use wooden main blades with the Blade 700 X Using wooden main blades may cause injury or property damage As you become more familiar with the helicopter s response adjust the rates expo pitch and throttle curves to suit your flying style C eeng Blade Tracking WARNING Always maintain a safe distance of at least 13 meters 2 Watch the movement at the blade tips Both blades should travel in the 45 feet when checking the main rotor blade tracking same plane 3 If one blade tip appears to be higher than the other land the helicopter To check the blade tracking disconnect the flight battery and adjust the blade linkages 1 Put the helicopter in a hover at an altitude near eye height 4
24. ng Hub w Sprague 700 X Moyeu de roue libre avec roue Mozzo cuscinetto unidirezionale con ruota BLH57185 bearing 700 X Blade 700 X Freilauf libre cames libera 700 X BLH5775 3 Blade Head Conversion 700 X Blade 700X 3 Blatt Rotorkopfumbau 700 x Conversion tripale Conversione testa a 3 pale 700 X d 700 X Axes de pieds de pales pour BLH5776 3 Blade Head Spindle 3 700 X Blade 700X 3 Blattlagerwelle conversion tripale 3 Alberino testa 3 pale 700 X BLH5777 3 Blade Head Block 700 X Blade 700X 3 Blattrotorkopf Ge Moyeu de t te pour conversion Bloccaggio testa 3 pale 700 X BLH5735A Metal FBL Unit Mount 700 X Blade 700X Metallhalter FBL Einheit DO X Support en m tal de module d Supporto metallo per unit FBL 700 X BLH5732A Metal Anti Rotation Bracket 700 X Sch Metall Taumelscheiben 700 X Guide anti rotation en m tal Staffa in metallo anti rotazione 700 X Metal Tail Rotor Pitch Lever Set Blade 700 X Metall Heckrotorpitch EE A Set leve in metallo per passo rototre BLH5752A 700 X 700 X Levier d anticouple metal 700 X RVOB071050 710mm FBL 3D Carbon Main Revolution 710mm FBL 3D Carbon Pales principales FBL 3D en carbone 710mm Pale principali in carbonio per Blades Hauptrotorblatt 710mm 3D e FBL SPMSH6200 H6200 HV Digital High Speed Heli Spektrum H6200 HV Digital Hi Speed Servo H6200 HV digital haute vitesse H6200 HV Servo digitale MG alta velocit Cyclic MG Servo Heli Taumel
25. od length and tail settings on AR7200BX are correct after mak ing any changes Cyclic gain is too high Decrease Dial 1 on the AR7200BX The helicopter wobbles in flight Headspeed is too low Increase the helicopter s head speed via your transmitter settings and or using a freshly charged flight pack Dampers are worn Replace the main rotor head dampers Limited Warranty What this Warranty Covers Horizon Hobby Inc Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in materials and workmanship at the date of purchase What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Horizon Hobby authorized service center v Product not purchased from an authorized Horizon dealer or vi Product not compliant with applicable technical regulations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PR
26. oduct purchaser is advised to return the Product immediately in new and unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of purchase cannot provide warranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative poa _ Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes ma
27. or a rubber mat to prevent screws from bounc ing off the worktable It s also a good idea to use small containers to keep parts organized after you take them out of the bags Most importantly take your time Review every assembly step and make sure you understand how the parts fit before you start bolting things to gether When you re done you ll have a capable smooth flying helicopter that flies exactly as it was designed to Flight Guidelines and Warnings eene 21 Flying Your 700X de PN 21 DEI Le Ar PR 22 Adjusting the Rudder Gain 22 Post Flight Inspection and Maintenance Checklist 22 AR7200BX Fine Tuning and Adjustment 22 Troubleshooting Guide I nnns 29 Limited VC CIE 24 Warranty and Service Contact Information 25 Compliance Information for the European Umon 25 Exploded II 98 101 Parts List Ersatzteile Pieces de rechange Pezzi di ricambio 102 103 Optional Parts Optionale Bauteile Pi ces optionnelles Pezzi opzionali 103 Blade 700 X Specifications Length Component Kit Combo Revolution 690mm FBL 3D Carbon Main Blades Main Rotor Blades ES 53 3 in 1350mm oe 155 in 95 mm tin mm Component Combo Kit DSM2 DSMX compatible AR7200BX 7CH DSMX Flybarless Control System To register
28. osionszeichnung Heckausleger Vue clat e Assemblage de la poutre Vista esplosa Gruppo tubo coda zs 22 Ly SAN Parts List Ersatzteile Pi ces de rechange Pezzi di ricambio Part English Deutsch Fran ais Italiano BLH5701 Main Rotor Grip Set 700 X Blade 700 X Rotorblatthalterset 700 X Pieds de pales principales Set portapale rotore principale 700 X BLH5702 Main Grip Arms 700 X Blade 700 X Rotorblatthalterarmset de pieds de pales Braccetti portapale 700 X BLH5703 Spindle Set 2 700 X Blade 700 X Blatthalterwelle 2 700 X Axe de pieds de pales 2 Set alberino 700 X D BLH5704 Main Rotor Blade Bolt Set 2 700 X Blade 700 X Rotorblattbolzen 2 ade fixations de pales Set viti pala rotore principale 700 X BLH5705 Dampers 4 700 X Blade 700 X D mpfer 4 700 X Amortisseurs 4 Smorzatori 700 X 6 BLH5706 Head Block 700 X Blade 700 X Rotorblockkopf 700 X Moyeu de t te Blocco testa 700 X 7 BLH5707 Main Rotor Head Link Set 700 X Blade 700 X Anlenkungen Hauptrotorkopf 700 X Set de tringleries de t te rotor testa rotore principale 8 BLH5708 Follower Arms 700 X Blade 700 X Taumelscheibenmitnehmer 700 X Bras flybarless Bracci inseguitore 700 X 9 BLH5709 Radius Arms 700 X Blade 700 X Pitchkompensator 700 X Bras radiaux Braccetti testa 700 X BLH5710 Servo Control Arm Set 700 X Blade 700 X Servoarm Set 700 X Set de bras de
29. p Head Shoulder Bolt x2 M3 Lock Nut x2 Tail assembly cont d e Glue the torque tube bearings in place by placing a thin bead of CA on the torque tube at the given loca tions 278mm 300mm then slide the bearings onto the CA Do not allow CA to get into the bearings Step T7 parts bags T5 and T6 umm M3 X 12 Button Head Self Tapping Screw x3 Tail assembly cont d Tail Servo Neutral Position Head Bolt M2 X 12 Button Head Bolt M2 Nut Servo Control Ball Step T8 parts T7 T8 and T9 C M3 X 6 Button Head Bolt x2 wu D M3 X 25 Cap Head A ehoulder Bolt x4 E M3X28 Cap MM Head Shoulder Bolt M3 Lock Nut x4 e he tail servo horn and pushrod linkage must be assembled before mounting the servo horn Thread the ball link onto pushrod insert the control ball into the link and then thread the 2 X 12mm machine screw through the servo horn and control ball Set the tail servo for the neutral position then install the servo horn onto the servo splines so the servo horn is 90 to the pushrod at neutral Step T9 parts bag T10 Hexagonal Post A M3X 22 Cap Head Shoulder Bolt WOH B M3 X 16 Cap Head Bolt x2 M3 Washer x4 Frame Insert Spacer x2 ESC and Battery Tray Assembly Step ESC parts bag F10 Hexagonal Post x2 Battery Tray Post x2 M3 X 8 Cap Head Bolt x6 M2 5 X 6 Counter Sunk Bolt x2 M3 X
30. ress Horizon Service Center Repairs and Repair Requests servicecenter horizonhobby com RequestForm www quickbase com db Horizon Product Support bghj7ey8c a GenNewRecord 4105 Fieldstone Rd Product Technical Assistance RE wa 888 959 2304 Champaign Illinois 61822 USA sales horizonhobby com Sales 888 959 2304 United States of America TT Service Parts Sales sales horizonhobby co uk Units 1 4 Ployters Rd Staple Tye 9 Horizon Hobby Limited 44 0 1279 641 097 Harlow Essex CM18 7NS United Kingdom Horizon Technischer Service service horizonhobby de Christian Junge StraBe 1 Sales Horizon Hobby GmbH 49 0 4121 2655 100 25337 Elmshorn Germany France Service Parts Sales infofrance horizonhobby com 11 Rue Georges Charpak Horizon Hobby SAS 33 0 1 60 18 34 90 77127 Lieusaint France China Service Parts Sales info horizonhobby com cn Room 506 No 97 Changshou Rd Horizon Hobby China 86 021 5180 9868 Shanghai China 200060 Germany Compliance Information for the European Union Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2013072101 Product s Blade 700 X Pro Series Combo Item Number s BLH5725C The object of declaration described above is in conformity with the requirements of the specifications listed below following the provisions of the European R amp TTE Directive 1999 5 EC and European EMC Directive 2004 108 EC EN 301 489 1 V1 9 2 2012 EN301 489 17 V2
31. role Supporto unit FBL 700 X BLH5736 Fr Tail Boom Case 700 X Blade 700 X Heckrotorgeh use vorne 700 X Support de poutre de queue Scatola coda 700 X BLH5737 Canopy Posts 700 X Blade 700 X Kabinenhaubenstreben 700 X Supports de bulle Appoggi capottina 700 X BLH5738 Tail Pinion Gear 27T 700 X Blade 700 X Heckrotorritzel 700 X Pignon d anticouple 27T Pignone coda 700 X BLH5739 Bevel Gear 25T 700 X Blade 700 X Kegelrad 25T 700 X Pignon conique 25T Ingranaggio conico 25T 700 X BLH5740 Bevel Gear 24T 700 X Blade 700 X Kegelrad 24T 700 X Pignon conique 24T Ingranaggio conico 24T 700 X D BLH5741 Tail Shaft Bevel Gear 24T 700 X Blade 700 X Kegelrad Heckrotorwelle Ee conique d axe d anti ingranaggio conico albero coda 700 X BLH5742 Tail Shaft 700 X Blade 700 X Heckrotorblattwelle 700 X Axe d anticouple Albero coda 700 X BLH5743 Tail Pinion Shaft 700 X Blade 700 X Welle f Heckrotorritzel Ge Axe d entrainement d anti Pignone albero coda 700 X BLH5744 Boom Support Set 700 X Blade 700 X Halter Heckausleger 700 X Renforts de poutre de queue Set supporto tubo coda 700 X 44 BLH5745 Boom 2 700 X Blade 700 X Heckausleger 2 700 X Poutre de queue 2 Tubo coda 700 X 45 BLH5746 Torque Tube Assembly 700 X Blade 700 X Heckwelle RE de transmission Gruppo barra di torsione 700 X D BLH5747 Torque Tube Holder 700 X Blade 700 X Halter f Heckwelle 00 X Support d arbre de transmis Supporto barra di torsione 7
32. scheibenservo MG pignons m tal pour le cyclique per ciclico heli SPMSH6210 H6210 HV Digital Ultra Speed Heli Spektrum H6210 HV Digital Ultra Servo H6210 HV digital haute vitesse H6210 Servo digitale MG super alta Tail MG Servo Speed Heli Heckservo MG pignons m tal pour l anticouple velocit per coda heli 103 LLL BLH5778 Metal Tail Servo Bracket 700X Blade 700X Metall Heckservohalter d LA de servo d anticouple Staffa in metallo servo coda 700X 2013 Horizon Hobby Inc Blade E flite Dynamite Revolution EC5 Celectra DSM DSM2 DSMX AirWare ModelMatch and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby Inc The Spektrum trademark is used with permission of Bachmann Industries Inc BeastX is a registered trademark of Markus Schaack and is used with permission The Spektrum AR7200BX employs technology exclusively licensed to Horizon Hobby Inc from freakware GmbH Created 5 13 39874
33. servo Set bracci controllo servo 700 X BLH5711 Servo Control Link Set Blade 700 X Servonanlenkungen Set 700 X Set de tringleries de servo Set comandi servo 700 X BLH5712 Aluminum Swashplate 700 X Blade 700 X Aluminium Taumelscheibe 700 X Plateau cyclique en aluminium Piatto oscillante alluminio 700 X BLH5713 Swashplate Ball Set 700 X 700 X Kugelk pfe Taumelscheibe Set de rotules de plateau Set sfere piatto 700 X BLH5714 Main Shaft 2 700 X Blade 700 X Hauptrotorwelle 700 X Axe principal 2 Albero principale 700 X BLH5715 Main Shaft Retaining Collar 700 X Blade 700 X Stellring f Hauptrotorwelle equus de retenue de l axe Collare albero principale 700 X BLH5716 Main Gear 2 700 X Blade 700 X Hauptzahnrad 2 700 X Couronne principale 2 Ingranaggio principale 700 X BLH5717 Autorotation Gear 2 700 X Blade 700 X Autorotationsfreilauf 2 700 X Couronne d autorotation 2 Ingranaggio autorotazione 700 X One Way Bearing Hub w One way EDS 700 X Moyeu de roue libre avec Cuscinetto unidirezionale c supporto uerg One Way Bea Blade 700 X Freilauftager m BLH5719 One Way Bearing Sleeve 700 X Blade 700 X Freilaufbuchse 700 X Axe de roue libre E BLH5720 Stock Canopy 700 X Blade 700 X Kabinenhaube 700 X Bulle d origine Capottina di serie 700 X BLH5721 Canopy Grommets 700 X Blade 700 X Kabinenhaubenhalter TA Caoutchoucs de fixation de Gommini capottina 700 X BLH5722 CF Main Frame 1 L or R 700 X Blade 700 X
34. to operate it e Only use Horizon approved replacement parts and accessories for this product e Never place any portion of the model in your mouth as it could cause serious injury e Never operate your transmitter or helicopter with low transmitter batteries e Never connect the battery unless using or testing the product Do not perform maintenance with the battery installed e Never operate this product if you are tired ill taking any medications that impair judgment or are under the influence of alcohol or drugs e Never spray glass cleaner or any other liquid on this product e Always keep hair and dangling or loose items well away from the blades when the battery is connected NOTICE Modification with non Horizon approved components may result in refusal of service by Horizon WARNING This is a large model helicopter with carbon fiber blades that spin at very high RPM Always use extreme caution and common sense when maintaining and operating this product If you are unsure about ANY function or procedure described in this manual DO NOT operate Contact Horizon Product Support for assistance AN WARNING Always ensure you are operating the helicopter a safe distance 45 feet 13 meters away from yourself and others EU 471 III lt PA pet LES JW a Ell ds
35. x10x4mm Cuscinetto radiale 69 BLH5561 12x18x4mm Radial Bearing Blade 700 X 12x18x4mm Radiallager Roulement 12x18x4mm 12x18x4mm Cuscinetto radiale 115mm Carbon Fiber 3D Tail Rotor Revolution 115mm Carbon Fiber 3D Pales d anticouple 3D en carbone I RVOT011500 Blades Heckrotorbl tter ion 115mm Pale coda in carbonio per 3D Revolution 690mm FBL 3D Carbon Pales principales FBL 3D en carbone 690mm Pale principali in carbonio per RVOB069050 690mm FBL 3D Carbon Main Blades Hauptrotorblatt 690mm 3D e FBL BLH5771 Helicopter Main Blade Holder 700 X Blade700X Blathalter 700X Supportdespalesprincipales Supporto pala principale heli 700 X 77 EFLM60700B Heli 700 Brushless Outrunner Motor E flite Heli 700 Brushless AussenlauferMo Moteur brushless 700 H li cage Heli 700 motore a cassa rotante 520Kv tor 520Kv tournante 520kv brushless 520Kv EFLA2100 100 Amp HV Brushless ESC E flite 100 Amp HV Brushless ESC Regler Contr leur brushless 100A HV 100 Amp Regolatore ESC brushless I EFLA108 HV Speed Control Programmer HV Speed Control Programmierkarte Programmateur de contr leur HV HV Programmatore x regolatore velocit Optional Parts Optionale Bauteile Pi ces optionnelles Pezzi opzionali Part English Deutsch Francais Italiano BLH5730B Black Landing Gear 700 X Blade 700 X Kufengestell schwarz 700 X Train d atterrissage noir Carrello atterraggio nero 700 X One Way Beari
36. y be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content service center render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions ar
37. your product online visit www bladehelis com Tools Needed To Complete e 1 5mm 2mm 2 5mm 3mm and 4mm hex drivers Pitch gauge e Ball link pliers e Metric calipers e Needle nose pliers e Petroleum based light viscosity lube e Phillips screwdriver e Medium cyanoacrylate CA e Wire cutter Required Items e Receiver Flybarless control unit AR7200BX SPMAR7200BX included with combo BLH5725C e 2X 5000mAh 68 22 2V 30C Li Po 10AWG with EC5 M connector EFLB50006S30 e E flite EC5 Battery Series Harness 10 AWG EFLAEC508 e E flite EC5 Device Charge Lead with 6 Wire amp Jacks e 3 Servos 3 H6200 servos SPMSH6200 included with combo BLH5725C 12 AWG and 5 connector EFLAEC512 e 1 Tail servo e E flite 200W charger EFLC3020 1 H6210 servo SPMSH6210 included with combo BLH5725C e Celectra 15VDC 250W Power Supply EFLC4010 e DSM2 DSMX compatible DX6i 6 channel transmitter or higher Optional Items e Dynamite Li Po Charge Protection Bag Large DYN1405 e Control Rod Set Up Tool RVO1004 A Ss e Revolution Low Bounce Rubber Work Mat RVO1020 Wa e Revolution Hex Driver EE Set 1 5 2 0 2 5 3 0mm RV02000 EL e Revolution Ball Link Tool RVO1009 e Revolution 2 5mm Op e Revolution Deluxe Ball tion Extended Hex Tip Link Pliers RVO1005 RVO2012 Assembly Guide Legend d Apply Petroleum Based lt Apply BLUE Threadlock
Download Pdf Manuals
Related Search