Liebherr CNPESF 4013
Contents
1. Press the setting button refrigerator compartment Fig 3 3 the number of times needed until the required temperature shines in the LED display Note gt Long pressing of the setting button sets a slightly colder value within a small temperature range e g between 5 C and 7 C The LED of the next lower temperature range then shines in the temperature display 5 3 3 Fan With the fan you can rapidly cool large quantities of fresh food or achieve a relatively even distribution of temperature across all the storage levels The forced air cooling is to be recommended athigh room temperature above33 C at high humidity The forced air cooling uses slightly more energy To save energy the fan switches off automatically when the door is open Switching on the fan gt Briefly press the fan button Fig 3 2 gt The fan button shines gt The fan is active In some appliances the fan is only acti vated when the compressor is running To switch off the fan gt Briefly press the fan button Fig 3 2 gt The fan button goes out gt The fan is switched off 5 3 4 Shelves Moving or removing shelves The shelves have stops preventing them from being uninten tionally pulled out Control Three small boxes are available through the customer service as optional equipment instead of one wide and one small box Either one or both the boxes can be used If particularly tall bottles are to2. Operating instructions Combined fridge freezer 20514 7085682 01 CN es esf sl 3 Appliance at a glance Contents 1 Appliance at a glance uuursnnunennnnnnonnnnennnnnennnnnenn 2 1 1 Description of appliance and equipmert 2 1 2 Range of appliance use uusnsnneneenenenneenennnne nennen 2 1 TEONOnm ee ee 3 1 4 External dimensions of the appliance 3 1 5 Saving energy uunnnessesennnnnennnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnn 3 2 General safety information uuuusennnunnnennnn 3 3 Controls and displays uuuuuunuaneennnnannnnnnnnnnnnnnnnnn 4 3 1 Operating and control elements 4 3 2 Temperature display ccccccccssccesseesssesesseeeeseees 5 4 Putting into operation uununesennnnnennnnnennnnnnnnnnnenn 5 4 1 Transporting the Appliance cccccceesseeeeeseeeeeeeees 5 4 2 Installing the ADPlIANCE ce ecceeeeeeeeeeeeeeeeeeeeeens 5 4 3 Changing over the door hinges 444 44 gt 6 4 4 Insertion into a row of kitchen units 8 4 5 Disposing of packagQing ecceeeeeeeeeeeeeeeeeeeeeees 8 4 6 Connecting the appliance ccccceesseeeeeesseeeeeees 8 4 7 Switching on the appliance ccccsseeeeeeseeeeeeeeees 8 5 COMI E A ERDE EEE ERER SER RUE EEEENEEENERSSERSERSEEERS 9 5 1 DOOF AA eepe 9 5 2 Temperature alarm cccccccc
3. Plug in the power plug 4 7 Switching on the appliance Note To switch on the entire appliance it is necessary only to switch on the freezer compartment In so doing the refriger ator compartment is automatically switched on as well Put the appliance into operation about 2 hours before first loading food to be frozen 4 7 1 Switching on the freezer compartment PressOn Off button freezer compartment Fig 3 9 gt The appliance is switched on The refrigerator compartment temperature display indicates the set temperature The freezer compartment temperature display and the alarm button flash until the temperature is sufficiently low gt If all LEDs in the display light up demo mode is activated Please contact the after sales service 4 7 2 Switching on the refrigerator compart ment Note When the refrigerator compartment is switched on the freezer compartment is automatically switched on as well Press On Off button refrigerator compartment Fig 3 7 gt The interior light is on when the door is open gt The temperature display shines Refrigerator compartment and freezer compartment are switched on Depending on model and options 5 Control 5 1 Door alarm For refrigerator and freezer compartment If the door is open for longer than 60 seconds the audible warning will sound The audible alarm is automatically silenced when the door is closed 5 1 1 Muting the door alarm Th
4. 5 4 9 Cold storage accumulators The cold storage accumulators prevent the temperature from rising too fast in the event of power failure Using cold storage accumulators Place the cold storage accumula tors in the top freezer compart ment to save space Place the frozen cold storage accumulators on the frozen food in the upper front area of the freezer compartment 5 4 10 IceMaker The IceMaker produces ice cubes using the water container located in the refrigerator compartment The water container can also be used to provide chilled drinking water The IceMaker is in the top drawer of the freezer compartment The drawer is marked IceMaker Make certain that the following conditions are met The appliance is level The appliance is connected The freezer compartment is switched on The water tank was cleaned with water and is filled Switching on the IceMaker Fig 14 Pull out the drawer Press the On Off button Fig 74 7 so that the LED Fig 14 2 shines Push in the drawer Note gt The IceMaker produces ice cubes only if the drawer is fully closed Producing ice cubes The production capacity depends on the freezer temperature The lower the temperature the more ice cubes can be produced in a specific period The ice cubes drop from the IceMaker into the drawer When a certain filling level has been reached no further ice cubes are produced The IceMaker d
5. The defrost water evaporates due to the compressor heat Drops of water on the rear wall are perfectly normal Regularly clean the drain opening to allow the water to flow away see 6 2 Freezer compartment The moisture condenses on the evaporator is periodically defrosted and evaporates gt The appliance does not have to be manually defrosted 6 2 Cleaning the appliance A WARNING Risk of injury and damage as a result of hot steam Hot steam can lead to burns and can damage the surfaces gt Do not use any steam cleaners NOTICE Incorrect cleaning damages the appliance gt Do not use cleaning agents in concentrated form Do not use any scouring or abrasive sponges or steel wool gt Please do not use any aggressive scouring sand chloride chemical or acid based cleaning agents gt Do not use chemical solvents gt Do not damage or remove the type plate on the inside of the appliance It is important for the customer service Do not pull off bend or damage cables or other compo nents gt Do not allow any cleaning water to enter the drain channel ventilation grille or electrical parts Please use soft cleaning cloths and a universal pH neutral cleaning agent Please use cleaning and care products suitable for contact with foodstuffs in the appliance interior Empty appliance gt Pull out the power plug Clean plastic outer and inner surfaces with lukewarm water and a lit
6. is saved This is normal in energy saving models SuperFrost is activated 14 gt The compressor runs for longer in order to rapidly cool the food This is normal A LED on the bottom rear of the appliance at the compressor flashes regularly every 15 seconds The inverter is equipped with a diagnostic LED The flashing is normal Excessive noise gt Due to the various speed steps speed regulated compressors can generate different running noises gt The sound is normal A bubbling and gurgling noise gt This noise comes from the refrigerant flowing in the refriger ation circuit gt The sound is normal A quiet clicking noise The noise is produced whenever the refrigeration unit motor automatically switches on or off p The sound is normal A hum It is briefly a little louder when the refrigeration unit the motor switches on The refrigeration increases automatically when the Super Frost function is activated fresh food has just been placed in the appliance or the door has been left open for a while gt The sound is normal The ambient temperature is too high Solution see 1 2 A low hum The sound is produced by air flow noise of the fan gt The sound is normal Vibratory noise gt The appliance is not fixed to the ground The running of the cooling unit therefore makes objects and adjacent furniture vibrate Adjust applian
7. it gt C lose the lower door stands firmly and on a evel DY Draw the middle bearing pin Fig 5 77 out of the turn hinge applying the zen ard oner oo spanner to the adjustable ae height feet A and using a gt Remove the plastic cap Fig 5 70 spirit level Te A CAUTION Then support the door Extend the adjustable foot at the turn hinge B until it rests on the floor and then make a further 90 turn Risk of injury if the door tips Take good hold of the door gt Set down the door carefully gt Open the lower door gt Unscrew the middle turn hinge 2x Torx 25 Fig 5 13 Note Lift up the door and set it aside gt Clean the appliance see 6 2 4 3 3 Transferring the middle bearing elements If the appliance is installed in a very damp environment condensate may form on the outside of the appliance Always see to good ventilation at the installation site 4 3 Changing over the door hinges You can change over the door hinges if necessary pe Me Eia Ensure that the following tools are to hand o 92 a r O Torx 25 a e Q Torx 15 Pi Q Screwdriver Ir U Cordless screwdriver if necessary DA SESS Q Second person for fitting work if needed Nas y k i Fig 5 TO RAC Ung KAUPPA BER gt Carefully detach the cover panel Fig 5 72 Note Turn the middle turn hinge Fig 5 73 with the washer gt Remove any food from the door racks before removing the Fig 5 14 th
8. it clicks into place K ye wir K w wir Fig 8 Lift the stopper Fig 8 30 out of the door bearing bush and transfer it Depending on model and options Putting into operation Detach door handle Fig 8 32 stopper Fig 8 33 and pres sure plates Fig 8 34 and transfer to the opposite side When fitting the pressure plates on the opposite side make sure they snap properly into place 4 3 6 Fitting the lower door Place the lower door from above onto the lower bearing pin Fig 6 22 gt Close the door Place the plastic cap Fig 5 70 back onto the middle turn hinge Fig 5 73 Place the middle bearing pin Fig 5 77 in the lower door on the new hinge side through the middle turn hinge Fig 5 13 4 3 7 Fitting the upper door Place the upper door on the middle bearing pin Fig 5 77 Insert the upper turn hinge Fig 4 3 in the door on the new hinge side gt Screw the upper turn hinge firmly into place with 4 Nm 2x Torx 25 Fig 4 4 Possibly make preliminary holes with a bradawl or use a cordless screwdriver Apply the cover Fig 4 7 and cover Fig 4 2 to the oppo site side from the outside and snap them into place 4 3 8 Aligning the doors If necessary align the doors to the appliance housing by way of the two oblong holes in the bottom turn hinge Fig 6 25 and middle turn hinge Fig 5 73 To do so unscrew the middle screw in th
9. soft drinks fruit juices or similar Note The use of filtered de carbonated water ensures the supply of drinking water with top quality flavour for problem free ice cube production You can achieve this water quality by using a table top water filter available from specialist shops Use only filtered de carbonated water to fill the water tank The IceMaker is supplied with water from a water tank in the refrigerator compartment see Appliance at a glance Before initial operation clean the water tank thoroughly with water to remove any dust etc Fig 15 Pull the water tank forwards gt Remove cover and fill tank with water Replace the lid put the filled water tank back into the holder and push it right to the back Note The water reservoir has to be slid all the way into the bracket provided for the purpose in the refrigerator compartment Depending on model and options Switching off the IceMaker If no ice cubes are needed the IceMaker can be switched off independently of the freezer compartment When the IceMaker is switched off the IceMaker drawer can also be used for freezing and storing food Press the On Off button for about 1 second until the LED goes out gt Clean the IceMaker gt This ensures that no water or ice remains in the IceMaker 6 Maintenance 6 1 Defrosting with NoFrost The NoFrost system automatically defrosts the appliance Refrigerator compartment
10. Note Place food inside the appliance as shown in the diagram This allows the appliance to save energy during operation gt Shelves drawers and baskets are arranged for optimum energy efficiency on delivery Fig 7 1 Transport grips atback 12 Coldest zone 2 Operating and control 13 Vegetable bin elements 3 Butter and cheese 14 Type plate compartment 4 Fan 15 Cold storage accumula tors 5 Door rack 16 VarioSpace 6 Interior light 7 Shelf sectioned 8 Bottle holder 9 Bottle shelf 10 Shelf relocatable 17 Freezer drawer 18 Ice cube tray 19 IceMaker 20 Information system 21 Adjustable feet transport grips at front transport castors at back 11 Drain hole 22 Water tank 1 2 Range of appliance use Intended use The appliance is suitable solely for cooling food in a domestic environment or similar This includes use in for example in staff kitchenettes bed and breakfast estab lishments by guests in country cottages hotels motels and other accommodation for catering and similar services in the whole sale trade Use the appliance solely in a domestic type of environment All other applications are inadmis sible Depending on model and options Foreseeable misuse The following applications are expressly prohibited Storage and cooling of medicines blood plasma laboratory compounds or similar materials and products s
11. appli ance NOTICE The stainless steel doors are finished with a high quality surface coating and must not be treated with the enclosed care product as otherwise the surface coating will be damaged 227 Please only use a soft clean cloth to wipe the coated door surfaces Only use a stainless steel care product on the stainless steel side walls applying it evenly in the direction of polishing Subsequent cleaning will then be easier Use only a soft clean cloth to wipe side walls and door surfaces with a paint finish gt Remove the protective film from the decorative trims and drawer fronts gt Remove all transit supports The spacers supplied with some appliances must be used to achieve the stated energy consumption These will extend the depth of the appliance by approx 35 mm The appliance is fully functional if the spacers are not used but does have a slightly higher energy consumption Putting into operation In the case of an appliance with enclosed wall spacers mount the wall spacers on the back of the appliance at the top left and right A CAUTION Risk of injury if the door tips Take good hold of the door gt Set down the door carefully gt Unscrew the upper turn hinge Fig 4 32x Torx 25 Fig 4 4 and lift it off Lift up the upper door and set it aside gt Dispose of packaging material see 4 5 4 3 2 Detaching the lower door Align the appliance so that
12. be stored hang only a single box above the bottle rack Re positioning the boxes Lift them for removal and re position them as p required Fig 10 Lift the shelf slightly and pull forward a little Adjust the height of the shelf To do so push the cut outs along the supports In order to remove the shelf fully place it at a slant and pull out towards the front Insert shelf with the raised edge pointing upwards at the back gt The food does not freeze onto the rear wall Dismantling shelves gt The shelves can be disman tled for cleaning Fig 11 gt The glass shelf with stop face 2 has to be at the back 5 3 6 Door racks Moving the storage rack The door racks can be dismantled for cleaning 5 3 7 Removing the bottle holder Always take hold of the bottle holder _ Remove storage rack according to on the plastic part illustration 5 4 Freezer compartment You can store frozen food make ice cubes and freeze fresh food in the freezer compartment The boxes can be removed and placed on the table as a single unit 10 Depending on model and options 5 4 1 Freezing food The rating plate indicates the maximum quantity of fresh food you can freeze within 24 hours see Appliance at a glance under Freezing capacity kg 24h The maximum load of frozen food for the drawers is 25 kg each and for the shelves 35 kg each A CAUTION Risk of
13. ce via the height adjustable feet Move bottles and containers apart Hum of the water tank pump When water is pumped out of the water reservoir a brief hum of the pump can be heard gt The sound is normal The SuperFrost button flashes together with the tempera ture display gt There is a fault Please contact the after sales service see Maintenance All LEDs are illuminated in the refrigerator compartment temperature display Demo mode is activated Please contact the after sales service see Maintenance The outer surfaces of the appliance are warm The heat of the refrigeration circuit is used to prevent condensate from forming This is normal The IceMaker cannot be switched on gt The appliance and therefore the connected Connect the appliance to the mains see Putting into opera tion The IceMaker does not make any ice cubes The IceMaker is not switched on Switch on the IceMaker The drawer of the IceMaker is not properly closed Close the drawer properly The water tank is not correctly inserted Insert the water tank There is not enough water in the water tank Fill the water tank IceMaker are not Vivivivi Depending on model and options The LED of the IceMaker flashes There is not enough water in the water tank p gt Fill the water tank Ifthe LED flashes and the water tank is full the IceMaker is defective Please co
14. ces supplied with wall spacers the measurement increases by 35 mm see 4 2 1 5 Saving energy Always ensure good ventilation Do not cover ventilation openings or grille Always keep fan louvres clear Donot place appliance in areas of direct sunlight or next to a stove heater or similar object The energy consumption depends on the installation condi tions e g the ambient temperature see 1 2 Keep the time the appliance is open to a minimum The lower the temperature setting the higher the power consumption Store food logically see Appliance at a glance Ensure that all food is well packed and covered for storage This will prevent frost from forming Remove food as needed in order that it does not warm too much First cool warm food to room temperature before storing it Defrost frozen food in the refrigerator Empty and switch off refrigerating unit for longer vacation periods Accumulated dust increases the energy consumption Once a year dust the refrigerating unit together with the metal grille of the heat exchanger at the back of the appliance 2 General safety information Danger for the user This appliance can be used by children of 8 years old and over and also by persons with Controls and displays restricted physical sensory or mental capacity or lack of experience and knowl edge if they are supervised or have been instructed on safe use of the a
15. e A WARNING Blocked ventilation openings pose a risk of fire and damage Always keep the ventilation openings clear Always ensure that the appliance is properly ventilated NOTICE Risk of damage due to condensate Do not install the appliance directly alongside a further refrigerator freezer L In the event that the appliance is damaged contact the supplier immediately before connecting to the mains U The floor at the site must be flat and level Q Do not install the appliance in a location where it is exposed to direct radiation of the sun next to a cooker heater and similar Q Always stand the appliance backed directly to the wall using the enclosed wall spacers see below Q The appliance may be moved only when it is empty Q Do not install the appliance without assistance Q The more R 600a refrigerant there is in the appliance the larger the room in which the appliance is standing needs to be In rooms that are too small a flammable mix of gas and air may be created if there is a leak According to the EN 378 standard every 11 g of R 600a refrigerant requires at least 1 m space in the room for the appliance The amount of refrigerant in your appliance is on the type plate inside the appliance gt Detach the connecting cable from the rear of the appliance removing the cable holder at the same time because other wise there will be vibratory noise Remove the protective film from the outside of the
16. e immediate proximity This can cause injury to the eyes vivy 8 Decommissioning 8 1 Switching off the appliance Note To switch on the entire appliance it is necessary only to switch off the freezer compartment In so doing the refriger ator compartment is automatically switched off as well 8 1 1 Switching off the freezer compartment Press ON OFF button freezer compartment Fig 3 9 for at least 3 seconds gt The temperature displays are dark The entire appliance is switched off Depending on model and options Decommissioning 8 1 2 Switching off the refrigerator compart ment Press ON OFF button refrigerator compartment Fig 3 7 for at least 3 seconds gt The interior light is off gt The temperature display of the refrigerator compartment is dark Note If only the refrigerator compartment is to be switched off e g during holidays then always pay attention the freezer compartment temperature display has to shine 8 2 Taking the appliance out of service Empty the appliance Put the IceMaker in the cleaning position see Mainte nance Pull out the power plug Clean the appliance see 6 2 gt Leave the door open to prevent odour 9 Disposing of the appliance The appliance contains some reusable materials and should be disposed of properly not simply with unsorted household refuse Appliances which are no longer needed must be disposed of in a pr
17. e audible alarm can be muted when the door is open The sound switch off function is active as long as the door is left open Press alarm button Fig 3 8 gt The door alarm is silenced 5 2 Temperature alarm The audible alarm sounds if the freezer temperature is not cold enough The alarm button flashes at the same time The cause of the temperature being too high may be warm fresh food was placed inside too much warm ambient air flowed in when rearranging and removing food power failure for some time the appliance is faulty The audible alarm is automatically silenced the alarm button Fig 3 8 goes out and the temperature display stops flashing when the temperature is sufficiently cold again If the alarm status persists see Malfunction Note Food may be spoilt if the temperature is not cold enough Check the quality of the food Do not consume spoiled food 5 2 1 Muting the temperature alarm The audible alarm can be muted When the temperature is sufficiently cold again the alarm function is active again Press alarm button Fig 3 8 gt The audible alarm is silenced 5 3 Refrigerator compartment The natural circulation of air in the refrigerator compartment results in zones differing in temperature It is coldest directly above the vegetable drawers and at the rear wall It is warmest at the top front of the compartment and in the door 5 3 1 Food refrigeration Note The ener
18. e bottom turn hinge Fig 6 25 A WARNING Risk of injury due to the door dropping out If the bearing parts are not screwed into place firmly enough the door may drop out This may lead to severe injuries What is more the door may not close and therefore the appliance may fail to cool properly Screw the turn hinges firmly into place with 4 Nm Check all of the screws and retighten if necessary Putting into operation 4 4 Insertion into a row of kitchen units IH P ca 40 Fig 9 1 Stack cabinet 3 Kitchen cabinet 2 Appliance 4 Wall For appliances supplied with wall spacers the measurement increases by 35 mm see 4 2 The appliance can be inserted into a row of kitchen units To match the appliance Fig 9 2 to the height of the row of units a suitable stack cabinet Fig 9 7 can be fitted above the appli ance When installing with kitchen units max depth 580 mm the appliance can be positioned directly next to the kitchen cabinet Fig 9 3 The appliance will project by 34 mm at the sides and 50 mm in the centre of the appliance in relation to the kitchen cabinet front Ventilation requirements At the back of the stack cabinet there has to be a ventilation duct of at least 50 mm depth throughout the width of the stack cabinet The ventilation space under the ceiling has to be at least 300 cm the larger the ventilation space the more energy saving the applianc
19. e is in operation If the appliance is installed with the hinges next to a wall Fig 9 4 the distance between appliance and wall has to be at least 40 mm This corresponds to the projection of the handle when the door is open 4 5 Disposing of packaging A WARNING Danger of suffocation due to packing material and plastic film gt Do not allow children to play with packing material The packaging is made of recyclable materials corrugated board cardboard expanded polystyrene parts polythene bags and sheets polypropylene straps nailed wooden frame with polyethylene panel Take the packaging material to an official collecting point oN 4 6 Connecting the appliance NOTICE Risk of damage to the electronic control system gt Do not use stand alone inverters conversion of d c to a c three phase or energy saving plugs A WARNING Fire and overheating hazard Do not use extension cables or multiple socket outlets The type of current alternating current and voltage at the installation site have to conform with the data on the type plate see Appliance at a glance The socket must be properly earthed and fused The tripping current for the fuse must be between 10 A and 16A The socket must be easily accessible so that the appliance can be quickly disconnected from the supply in an emergency It must be outside the area of the rear of the appliance Check the electrical connection
20. gy consumption increases and the cooling perform ance decreases if the ventilation is inadequate Always keep the air slits of the fan free Store perishable food such as ready to serve dishes meat products and sausages in the coldest zone Place butter and preserves in the upper area and in the door see Appli ance ata glance gt Use recyclable plastic metal aluminium and glass containers and cling film for wrapping Depending on model and options Control gt Use the front area of the refrigerator compartment floor only for briefly putting down cooled products e g when rear ranging and sorting However do not leave cooled products there otherwise they may be pushed back or tipped over when the door is closed Do not store food too close together to enable good air circulation To safeguard bottles from tipping over move the bottle holder 5 3 2 Setting the temperature The temperature depends on the following factors the door opening frequency the room temperature at the site where the appliance is installed the type temperature and quantity of frozen food Temperature setting to be recommended 5 C The temperature can be changed continuously Once the 1 C setting is reached it starts again with 9 C To access temperature adjustment press the setting button refrigerator compartment Fig 3 3 once gt The LED of the current temperature flashes in the tempera ture display
21. he interior e g steam cleaners heaters ice cream maker etc If refrigerant escapes remove any naked flames or sources of ignition from the leakage area Ventilate the room well Notify the after sales service Do not store explosives or sprays using combustible propellants such as butane propane pentane etc in the appliance To identify these spray cans look for the list of contents printed on the can or a flame symbol Gases possibly escaping may ignite due to electrical components Keep burning candles lamps and other items with naked flames away from the appliance so that they do not set the appliance on fire Please be sure to store alcoholic drinks or other packaging containing alcohol in tightly closed containers Any alcohol that leaks out may be ignited by electrical components Danger of tipping and falling Do not misuse the plinth drawers doors etc as a step or for support This applies particu larly to children Danger of food poisoning Do not consume food which has been stored too long Danger of frostbite numbness and pain Avoid lasting skin contact with cold surfaces or refrigerated frozen food or take protective steps e g wear gloves Do not consume ice cream water ice or ice cubes immediately and do not consume them too cold Danger of injury and damage Hot steam can lead to injury Do not use elec trical heating or steam cleaning equipment open flames or defro
22. injury due to broken glass Bottles and cans containing drinks may burst when being frozen This applies particularly to sparkling drinks gt Do not freeze bottles and cans containing drinks In order that the food is rapidly frozen through to the core do not exceed the following quantities per pack Fruit vegetables up to 1 kg Meat up to 2 5 kg Pack the food in portions in freezer bags reusable plastic metal or aluminium containers 5 4 2 Thawing food inthe refrigerator compartment inamicrowave oven in a conventional or fan oven at room temperature Food once thawed should be re frozen only in exceptional cases 5 4 3 Setting the temperature Temperature setting to be recommended 18 C The temperature can be changed continuously Once the 32 C setting is reached it starts again with 15 C To access temperature adjustment press setting button freezer compartment Fig 3 6 once gt The LED of the current temperature flashes in the tempera ture display of the freezer compartment Press the setting button freezer compartment Fig 3 6 the number of times needed until the required temperature shines in the LED display Note gt Long pressing of the setting button sets a slightly colder value within a small temperature range e g between 15 C and 18 C The LED of the next lower temperature range then shines in the temperature display 5 4 4 SuperFrost With thi
23. ntact the after sales service see Maintenance The temperature is not cold enough The door of the appliance is not properly closed Close the door of the appliance Insufficient ventilation Clear ventilation grilles The ambient temperature is too high Solution see 1 2 The appliance was opened too frequently or for too long Wait to see whether the appliance reaches the required temperature by itself If not please contact the after sales service see Maintenance Too much fresh food was placed inside without SuperFrost Solution see 5 4 4 gt The appliance is too close to a source of heat stove heater etc gt ie the position of the appliance or the source of heat Vivivivi The interior light is not on The appliance is not switched on Switch on the appliance The door was open longer than 15 min The interior light automatically switches off if the door has been open for about 15 min gt The LED illumination is defective or the cover is damaged A WARNING Risk of injury due to electric shock Live parts are located under the cover Have the LED interior light changed or repaired only by the customer service or by specialized personnel trained for the purpose A WARNING Danger of injury by LED lamp The light intensity of the LED illumination corresponds to laser class 1 1M If the cover is defective gt Do not look into the illumination with optical lenses from th
24. oes not fill the drawer right up to the brim 12 If large quantities of ice cubes are needed the complete IceMaker drawer can be exchanged for the adjacent drawer When the drawer is closed the IceMaker automatically re commences production Once the IceMaker has been switched on for the first time it may take up to 24 hours until the first ice cubes are produced Note When the appliance is used for the first time and if it has been out of use for a long time particles may collect in the IceMaker and or water conduit gt Therefore do not use or consume the ice cubes made in the first 24 hours Filling the water tank A WARNING Risk of poisoning The water quality must comply with the drinking water regu lations of the respective country in which the appliance is operating e g 98 83 EC NSF 61 Only fill with drinking water The IceMaker is solely intended to produce ice cubes in quantities customary for household use and must be oper ated using water appropriate for this purpose If the lceMaker is switched off or not used for a longer period of time empty the water tank NOTICE Risk of damage to the IceMaker Liquids containing sugar such as soft drinks fruit juices or similar gum up the pump and therefore lead to total pump failure and as a consequence to damage to the IceMaker Fill the water tank with cold drinking water only Do not use liquids containing sugar such as
25. ofessional and appropriate way in accordance with the current local regulations and laws When disposing of the appliance ensure that the refrigeration circuit is not damaged to prevent uncontrolled escape of the refrigerant it contains data on type plate and oil Disable the appliance Pull out the plug Cut through the connecting cable 15 Liebherr Hausger te Ochsenhausen GmbH Memminger Strasse 77 79 D 88416 Ochsenhausen www liebherr com
26. ood back inside 6 3 Cleaning the IceMaker Fig 16 The IceMaker has to be switched on Pull out the drawer and remove the ice cubes Clean the drawer with warm water and mild washing up liquid gt When the drawer is pulled out hold down the On Off button about 10 seconds gt After about 1 s the LED goes out the IceMaker is switched off gt After about 10 s the LED flashes for about 60 s Slide in the drawer while the LED is flashing gt The ice cube tray of the IceMaker turns to a skew position 13 Malfunction gt Remove the drawer Clean the ice cube tray with warm water If necessary use mild washing up liquid Then rinse Switch the IceMaker on again gt Press the ON OFF button until the LED shines then slide in the drawer gt The IceMaker starts producing ice cubes If washing up liquid was used throw away the first three loads of ice cubes to get rid of any remaining washing up liquid 6 4 Customer service First check whether you can correct the fault yourself by refer ence to the list see Malfunction If this is not the case please contact the customer service whose address is given in the enclosed customer service list A WARNING Risk of injury if repair work is not carried out professionally Have any repairs and action not expressly specified on the appliance and mains cable carried out by service personnel only see Maintenance Read the ap
27. pliance designation IB IQ 00 Fig 17 T service imm mm mas tt a No Fig 17 2 and serial No Fig 17 3 oO off the type plate seme aee cece ee cee Sateen Sete located inside the a appliance on the left hand side Fig 17 gt Notify the customer service specifying the fault appliance designation Fig 77 7 service No Fig 17 2 and serial No Fig 17 3 gt This will help us to provide you with a faster and more accu rate service Keep the appliance closed until the customer service arrives gt The food will stay cool longer Pull out the mains plug not by pulling the connecting cable or switch off the fuse 7 Malfunction Your appliance is designed and manufactured for a long life span and reliable operation If a malfunction nonetheless occurs during operation check whether it is due to a handling error In this case you will have to be charged for the costs incurred even during the warranty period You may be able to rectify the following faults yourself Appliance does not work gt The appliance is not switched on Switch on the appliance The power plug is not properly inserted in the wall socket Check power plug gt The fuse of the wall socket is not in order p Check fuse The compressor runs for a long time The compressor switches to a low speed when little cold is needed Although the running time is increased as a result energy
28. ppliance and understand the resulting risks Children must not be allowed to play with the appliance Cleaning and user maintenance must not be carried out by children without supervision When disconnecting the appliance from the supply always take hold of the plug Do not pull the cable In the event of a fault pull out the mains plug or deactivate the fuse Do not damage the mains power cable Do not operate the appliance with a defective mains power cable Have any repairs to or intervention in the appliance and any change of the mains power cable carried out by the customer service only or by other specialised personnel trained for the purpose Only assemble connect and dispose of the appliance according to the instructions Please keep these instructions in a safe place and pass them on to any subsequent owners All repairs to and intervention in the IceMaker may be carried out only by service personnel or by other skilled personnel trained for the purpose Special purpose lamps incandescent lamps LEDs fluorescent tubes in the appliance serve to illuminate the appliance interior and are not suited for room illumination Fire hazard The refrigerant R 600a is environmentally friendly but flammable Escaping refrigerant may ignite Do not damage the refrigerant circuit pipes e Do not allow naked flames or ignition sources to enter the appliance e Do not use any electrical appliances in t
29. rost is automatically deactivated after about 65 h gt The SuperFrost button extinguishes once freezing is completed Place produce in the drawers and push the latter back in again gt The appliance continues to operate in the energy saving normal mode 5 4 5 Drawers Note The energy consumption increases and the cooling perform ance decreases if there is insufficient ventilation For appliances with NoFrost gt Leave the bottom drawer in the appliance Always keep the air slits of the fan free at the rear wall To store frozen food directly on the shelves pull the drawer forwards and lift it out 5 4 6 Shelves To remove the shelf lift up at the front and pull out To put the shelf back simply push in as far as it will go 5 4 7 VarioSpace Apart from being able to remove the drawers you can also remove the shelves creating space for large items of frozen food Poultry meat large pieces of game and high bakery prod ucts can be frozen in one piece and prepared gt The maximum load of frozen food for the drawers is 25 kg each and for the shelves 35 kg each 11 Control 5 4 8 Information system Fig 13 1 Ready made meals ice 4 Sausages bread cream 2 Pork fish 5 Game mushrooms 3 Fruit vegetables 6 Poultry beef veal The figures indicate the storage time in months for several types of frozen food in each case Storage times given are guide times
30. rough 180 and screw it firmly into place on the door so that no food falls out new hinge side with 4 Nm Turn the cover panel Fig 5 72 through 180 and snap it into place again on the new handle side a E Fig 4 Close the upper door Pull off the cover Fig 4 1 forwards and upwards Lift off the cover Fig 4 2 6 Depending on model and options 4 3 4 Transferring the lower bearing elements Fig 6 Lift out the bearing pin Fig 6 22 together with washer Fig 6 23 and foot Fig 6 24 Lift off the stopper Fig 6 27 gt Unscrew Fig 6 26 the turn hinge Fig 6 25 gt Unscrew Fig 6 29 the bearing element Fig 6 28 transfer it to the opposite location hole of the turn hinge and screw it firmly into place gt Carefully lift off the cover on the handle side Fig 6 27 and transfer it to the opposite side gt Screw the turn hinge Fig 6 25 firmly into place on the new hinge side possibly using a cordless screwdriver with 4 Nm gt Re insert the stopper Fig 6 27 into the other hole gt Re insert the bearing pin Fig 6 22 together with washer and foot In so doing pay attention that the locating lug points backwards 4 3 5 Transferring the handles On both the upper and lower door Transfer the spring clamp Fig 7 31 Depress the latch nose and pull the spring clamp off over it Slide the spring clamp into place on the new hinge side until
31. s function you can freeze fresh food quickly through to the core The appliance operates with maximum refrigeration The noise of the refrigeration unit may be temporarily louder as a result The maximum amount of fresh food which can be frozen in 24 h is indicated on the type plate under freezing capacity kg 24h This amount varies according to the model and climate rating You have to activate SuperFrost in good time depending on how much fresh food is to be frozen about 6 hours before placing the food inside in case of small amounts and about 24 hours in advance in case of the maximum amount of food to be frozen Wrap produce and spread it out as far as possible Do not allow produce to be frozen to touch produce that is already frozen to prevent the latter thawing You do not have to activate SuperFrost in the following cases when placing frozen food in the freezer Depending on model and options Control Freezing with SuperFrost Briefly press the SuperFrost button Fig 3 7 gt The SuperFrost button shines gt The freezer temperature drops the appliance operates with the maximum refrigerating capacity In case of a small amount of food to be frozen wait approx 6 h Place wrapped produce in the top drawers In case of the maximum amount of food to be frozen see type plate gt wait about 24 h gt Remove top drawers and place produce directly on the top shelves gt SuperF
32. scccccsececsseeesseeeeeeeessees 9 5 3 Refrigerator compartMent ccceceeeeeeeeeeeeeeeeeees 9 5 4 Freezer compartment uusssssseenenenenennnenennen nennen 10 6 Namlenance un eiieieheneisneneineee nieder 13 6 1 Defrosting with NoFrost 44u4s0044s nennen 13 6 2 Cleaning the appliance cccccssseeeeeeseeeeeeeseeeees 13 6 3 Cleaning the IceMaker u neeennnnennnnenn 13 6 4 Customer service annsesnsssnnesnnennennnnnnnnnennnne nennen 14 7 Mahne OM sisececsieis coccaviecescsadevecsvaxwtnieusueetessenuenstieetes 14 8 DecommissioniNd uu n n ee 15 8 1 Switching off the appliance 4440ne nen 15 8 2 Taking the appliance out Of service nunneenneeneneen 15 9 Disposing of the appliance uuusnnnnnnennnnnnnnnnnnn 15 The manufacturer works constantly on the further development of all the types and models Therefore please understand that we have to reserve the right to make design equipment and technical modifications To get to know all the benefits of your new appliance please read the information contained in these instructions carefully The instructions apply to several models Differences may occur Text relating only to specific appliances is marked with an asterisk Instructions for action are marked with a the results of action are marked with a gt 1 Appliance at a glance 1 1 Description of appliance and equip ment
33. several degrees 4 Putting into operation 4 1 Transporting the appliance A CAUTION Risk of injury and danger of damage as a result of incorrect transport Transport the appliance in a packed condition Transport the appliance upright gt Do not transport the appliance without assistance 4 2 Installing the appliance A WARNING Fire hazard due to dampness If live parts or the mains lead become damp this may cause short circuits The appliance is designed for use in enclosed areas Do not Operate the appliance outdoors or in areas where it is exposed to splash water or damp conditions A WARNING Risk of fire due to short circuit If the mains cable connector of the appliance or of another appliance touch the rear of the appliance the mains cable connector may be damaged by the appliance vibrations leading to a short circuit Stand the appliance so that it is not touched by connectors or main cables gt Do not plug the appliance or any others into sockets located near the rear of the appliance A WARNING Fire hazard due to refrigerant The refrigerant R 600a is environmentally friendly but flam mable Escaping refrigerant may ignite gt Do not damage the piping of the refrigeration circuit Depending on model and options Putting into operation A WARNING Fire hazard and danger of damage Do not place appliances emitting heat e g microwaves toasters etc on the applianc
34. sting sprays to defrost Do not use sharp implements to remove the ice Please observe the specific information in the other sections DANGER identifies a situation involving direct danger which if not obviated may result in death or severe bodily injury WARNING _ identifies a dangerous situation which if not obviated may result in death or severe bodily injury CAUTION identifies a dangerous situation which if not obviated may result in minor or medium bodily injury NOTICE identifies a dangerous situation which if not obviated may result in damage to property Note identifies useful information and tips 3 Controls and displays 3 1 Operating and control elements fo lie el Fig 3 6 Setting button freezer compartment 1 On Off button refriger ator compartment Depending on model and options 2 Fan button 3 Setting button refriger ator compartment 4 Refrigerator compart ment temperature display 5 Freezer compartment temperature display 7 SuperFrost buttont 8 Alarm button 9 On Off button freezer compartment 3 2 Temperature display The following are displayed in normal operation the set freezing temperature the set cooling temperature The freezer compartment temperature display flashes the temperature setting is being changed after switch on the temperature is not yet cold enough the temperature has risen
35. tle washing up liquid Depending on model and options Maintenance NOTICE The stainless steel doors are finished with a high quality surface coating and must not be treated with the enclosed care product as otherwise the surface coating will be damaged 227 Please only use a soft clean cloth to wipe the coated door surfaces In the case of heavy soiling use a little water or neutral cleaning agent A micro fibre cloth can be used optionally When soiled clean stainless steel side walls with a commercially available stainless steel cleaning agent Then apply the enclosed stainless steel care product evenly in the direction of polishing Use only a soft clean cloth to wipe side walls and door surfaces with a paint finish In the case of heavy soiling use a little water or neutral cleaning agent A micro fibre cloth can be used optionally Clean drain hole Remove deposits with a narrow instrument e g a cotton bud gt Most of the parts can be dismantled for cleaning see the relevant chapter Clean items of equipment by hand with lukewarm water and a little washing up liquid Empty water collect tray remove water tank Carefully unlatch tray at front and then remove from below After cleaning gt Wipe dry the appliance and items of equipment Connect the appliance and switch it on again Switch on SuperFrost see 5 4 4 When the temperature is sufficiently cold Put the f
36. ubject to the Medical Devices Directive 2007 47 EC Use in potentially explosive areas Improper use of the appliance can lead to damage to or spoilage of the stored goods Climate rating definitions The appliance is set to operate within specific ambient temperature limits according to its climate rating The correct climate rating for your appliance is indicated on the type plate Note Compliance with the ambient temperatures indicated is required otherwise the cooling performance is reduced Climate for ambient temperatures of rating SN 10 C to 32 C N 16 C to 32 C ST 16 C to 38 C T 16 C to 43 C 1 3 Conformity The refrigerant circuit is tested for leakage The appliance complies with the relevant safety regulations and EC Directives 2006 95 EC 2004 108 EC 2009 125 EC and 2010 30 EU Note for test institutions Tests are to be carried out according to the applicable standards and guidelines Preparation and testing of the appliances must be carried out taking the manufacturer s loading plans and the notes in the operating manual into account Depending on model and options General safety information 1 4 External dimensions of the appli ance ii r ae Imm fe QS Fig 2 Height of appliance H Model mm CN es sl 35 CNP esf sl 35 1817 CN 39 CNP esf 39 2011 CN es esf sl 40 2011 CNP esf 40 For applian
Download Pdf Manuals
Related Search