E-flite Inverza 280 BNF
Contents
1. 20 35 20 Adjusting Center of Gravity CG The CG location is 77mm from the trailing edge of the wing tip The battery compartment is oversized to allow for Center of Gravity adjustment Start by centering the battery in the battery compartment Adjust as needed by sliding the battery forward or back Removing the Landing Gear 1 Remove the 4 screws A fairings B and covers C from the fuselage 2 Push the landing gear struts together and pull away from the fuselage to remove the landing gear Assemble in reverse order 11 Flying Tips and Repairs Consult local laws and ordinances before choosing a location to fly your aircraft We recommend flying your aircraft outside in no greater than moderate winds Always avoid flying near houses trees wires and buildings You should also be careful to avoid flying in areas where there are many people such as busy parks schoolyards or soccer fields Takeoff Place the aircraft in position for takeoff facing into the wind Set dual rates to LOW POSITION and gradually increase the throttle to to full and steer with the rudder Pull back gently on the elevator and climb to check trim Once the trim is adjusted begin exploring the flight envelope of the aircraft Flying This aircraft is extremely responsive to control2. input Fly at low rate settings until you are familiar with its response Fly your first attempts at high rate settings at high altitude and slow speeds Landing Make sure to land into the wind Fly the aircraft to approximately 36 inches 90 cm or less above the runway using a small amount of throttle for the VA entire descent Keep the throttle on until the aircraft 1 Disconnect flight battery from ESC is ready to flare During flare keep the wings level Required for safety and battery life and the aircraft pointed into the wind Gently lower the throttle while pulling back on the elevator to 2 Power off transmitter bring the aircraft down on its wheels 3 Remove flight battery from aircraft NOTICE If a crash is imminent reduce the throttle DS 4 Recharge flight battery and trim fully Failure to do so could result in extra damage to the airframe as well as damage to the 5 Store flight battery apart from aircraft ESC and motor and monitor the battery charge Post Flight Checklist NOTICE Crash damage is not covered under 6 Make note of flight conditions and warranty flight plan results planning for future i flights Repairs Repair this aircraft using foam compatible CA cyanoacrylate adhesive glue or clear tape Only use foam compatible CA glue as other types of glue can damage the foam When parts are not repairable see the Replacement Parts List for ordering by item number For a listing of
3. BNF BASIC INVERZA 280 Instruction Manual Bedienungsanleitung Manuel d utilisation Manuale di Istruzioni Elite ADVANCING ELECTRIC FLIGHT NOTICE All instructions warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby Inc For up to date product literature visit www horizonhobby com and click on the support tab for this product Meaning of Special Language The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product NOTICE Procedures which if not properly followed create a possibility of physical property damage AND little or no possibility of injury CAUTION Procedures which if not properly followed create the probability of physical property damage AND a possibility of serious injury WARNING Procedures which if not properly followed create the probability of property damage collateral damage and serious injury OR create a high probability of superficial injury A WARNING Read the ENTIRE instruction manual to become familiar with the features of the product before operating Failure to operate the product correctly can result in damage to the product personal property and cause serious injury This is a sophisticated hobby product It must be operated with caution and common sense and requires some basic mechanical ability Failure to operate this product in a safe and responsible m
4. all replacement and optional parts refer to the list at the back of this manual NOTICE Use of foam compatible CA accelerant on your aircraft can damage paint DO NOT handle the aircraft until accelerant fully dries NOTICE When you are finished flying never keep the aircraft in the sun Do not store the aircraft in a hot enclosed area such as a car Doing so can ee the foam Service of Power Components Disassembly A CAUTION Always disconnect the battery before handling or adjusting the propeller or motor Failure to do so could result in personal injury Propeller 1 Remove the 2 screws A from the spinner B Carefully separate the spinner from the back plate C 2 Remove the lock nut D from the propeller shaft E then remove the propeller F and back plate Motor and Firewall 1 Carefully remove the cowling G from the fuselage Paint may hold the cowling on the fuselage 2 Loosen the set screws H and remove the washer I before removing the propeller shaft from the motor J 3 Remove the 4 screws K and motor mount L from the fuselage 4 Disconnect the motor wires from the ESC 5 Loosen the set screws M and remove the motor from the motor mount Assemble in reverse order Assembly Tips e Correctly align and connect the motor wire colors with the ESC wires e The propeller size numbers 6 8 x 3 5 must face out from the motor for correct propeller operation e Ensure th
5. controller 10A EFLA7300 E AR6310 DSMX Nanolite 6Ch Rx Air SPMAR6310 3 3 5 g Digital Servo EFLR7100 Needed to Complete Recommended Battery 450mAh 35 CETO 11 1V 50C Li Po 18AWG JST EFLB4503SJ50 7 Recommended Battery Charger I 26in 660mm H mm Celectra 80W AC DC Multi Chemistry Battery Charger EFLC3025 k 26 in 660mm _ VW 3111 Recommended Transmitter Full Range 8 302 Lee DSM2 DSMX technology with adjustable 235 9 Dual rate and exponential DX61 and up To register your product online go to www e fliterc com 3 Low Voltage Cutoff LVC When a Li Po battery is discharged below 3V per cell it will not hold a charge The aircraft s ESC protects the flight battery from over discharge using Low Voltage Cutoff LVC Once the battery discharges to 3V per cell the LVC will reduce the power to the motor in order to leave adequate power to the receiver and servos to land the airplane When the motor power decreases land the aircraft immediately and replace or recharge the flight battery Always disconnect and remove the Li Po battery from the aircraft after each flight Charge your Li Po battery to about half capacity before storage Make sure the battery charge does not fall below 3V per cell Failure to unplug a connected battery will result in trickle discharge For your first flights set your transmitter timer or a stopwatch to 5 minutes Adju
6. es Recapiti dei distributori Country of Purchase Horizon Hobby Address Phone Number Email Address 4105 Fieldstone Rd 800 338 4639 United States Champaign Illinois 61822 USA sales horizonhobby com Units 1 4 Ployters Rd Staple Tye 44 0 1279 641 097 Harlow Essex sales horizonhobby co uk CM18 7NS United Kingdom United Kingdom Horizon Hobby Limited Christian Junge StraBe 1 49 0 4121 2655 100 REESEN 25337 Elmshorn Germany RIA de 11 Rue Georges Charpak 33 0 1 60 18 34 90 Horizon Hobby SAS 77127 Lieusaint France ii com Room 506 No 97 Changshou Rd 86 021 5180 9868 Horizon Hobby China Shanghai China 200060 ui com cn 63 2013 Horizon Hobby Inc E flite Celectra DSM DSM2 DSMX ModelMatch Bind N Fly and the Bind N Fly logo are trademarks or registered trademarks of Horizon Hobby Inc The Spektrum trademark is used with permission of Bachmann Industries Inc Inverza and its design are trademarks of Kevin Kimball used under license to Horizon Hobby Inc Elite ADVANCING ELECTRIC FLIGHT The trim scheme of the Inverza was designed by Mirco Pecorari of Aircraft Studio Design Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan Patents pending www e fliterc com EFL6350 Created 03 13 36771
7. liability is asserted As Horizon has no control over use setup final assembly modification or misuse no liability shall be assumed nor accepted for any resulting damage or injury By the act of use setup or assembly the user accepts all resulting liability If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product purchaser is advised to return the Product immediately in new and unused condition to the place of purchase Law These terms are governed by Illinois law without regard to conflict of law principals This warranty gives you specific legal rights and you may also have other rights which vary from state to state Horizon reserves the right to change or modify this warranty at any time without notice WARRANTY SERVICES Questions Assistance and Services Your local hobby store and or place of purchase cannot provide warranty support or service Once assembly setup or use of the Product has been started you must contact your local distributor or Horizon directly This will enable Horizon to better answer your questions and service you in the event that you may need any assistance For questions or assistance please visit our website at www horizonhobby com submit a Product Support Inquiry or call 877 504 0233 toll free to speak to a Product Support representative Inspection or Services H this Product needs to be inspected or serviced and is compliant in
8. rotante 1800Kv 1800Kv EFL635010 Decal Set Inverza E flite Inverza 280 Planche de d coration Set decals Inverza 280 BNF BNF Dekorbogen Inverza 280 BNF 280 BNF EFL635011 Servo Extension set E flite Edge 540 QQ Set de rallonges pour Set prolunghe Micro Micro Dekorbogen Servo EFLP6835E 6 8x3 5 Electric E flite 6 8x3 5 Elektro E lectrique 6 8 6 8x3 5 Elica per Propeller Propeller motore elettrico AR6310 DSMX Spektrum 6 Kanal elo AG 0 AR6310 DSMX Ricevi SPMAR6310 Nanolite 6 Channel SE Empfanger DSMX Nanolite 6 voies tore Nanolite a 6 canali Receiver EFL635012 Motor Shaft Inverza E flite Inverza 280 Axe moteur Inverza ay motore Inverza 280 BNF BNF Motorwelle 280 BNF 280 BNF EFLR710001 Gear Set EFLR7100 E flite Getriebe Set Jeu de pignons Set ingranaggi EFLR7100 EFLR7100 EFLR7100 EFLR710002 Servo Arm Set E flite Servo Arm Set Set de bras de servo Set squadrette servi EFLR7100 EFLR7100 EFLR7100 EFLR7100 EFLR710003 Servo Arm Set Eflite EFLR7100 Set de bras de servos Set squadrette servi long EFLR7100 Servo Arm Set lang longs EFLR7100 lunghe EFLR7100 62 Optional Parts and Accessories Optionale Bauteile und Zubehorteile Pi ces optionnelles et accessoires Parti opzionali e accessori Part e Nummer ee BARA T Num ro Codice Description Beschreibung Description Descrizione EFLA230 Charger Lead with E flite Ladekabel m Cable de charge avec Cav
9. Product Support office Warranty Requirements For Warranty consideration you must include your original sales receipt verifying the proof of purchase date Provided warranty conditions have been met your Product will be serviced or replaced free of charge Service or replacement decisions are at the sole discretion of Horizon Non Warranty Service Should your service not be covered by warranty service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50 of the retail purchase cost By submitting the item for service you are agreeing to payment of the service without notification Service estimates are available upon request You must include this request with your item submitted for service Non warranty service estimates will be billed a minimum of hour of labor In addition you will be billed for return freight Horizon accepts money orders and cashier s checks as well as Visa MasterCard American Express and Discover cards By submitting any item to Horizon 15 for service you are agreeing to Horizon s Terms and serviced Further the sender will be responsible for Conditions found on our website http www horizonhobby arranging return shipment of the un serviced Product com content _service center_render service center through a carrier of the sender s choice and at the sender s expense Horizon will hold non compliant Product for a per
10. a 280 BNF BNF Ruder Wing Set Inverza E flite Inverza 280 Paire d ailes Inverza Set ala Inverza 280 EFL63502 280 BNF BNF Tragflachen 280 BNF BNF EFL63503 Hatch Set Inverza E flite Inverza 280 Set de trappes Set portello Inverza 639 280 BNF BNF Haube Inverza 280 BNF 280 BNF EFL 4 Cowling Inverza E flite Inverza 280 Capot Inverza 280 Capottina motore 6350 280 BNF BNF Motorhaube BNF Inverza 280 BNF EFL6350 Stab Set Inverza E flite Inverza 280 Set de stabilisateur Set stabilizzatore 905 280 BNF BNF H henruder Set Inverza 280 BNF Inverza 280 BNF Landing Gear Wheel E flite Inverza 280 Train avec roues Set carrello Carenature EFL63506 Pants set Inverza BNF Fahrwerk Inverza 280 BNF ruote Inverza 280 BNF 280 BNF Radschuhe Set Wing Tube Inverza E flite Inverza 280 Cle d aile Inverza Gu ala Inverza 280 EFL63507 280 BNF BNF Tragfl chen 280 BNF verbinder Pushrod amp Control E flite Inverza 280 Tringleries et guignols Set comandi e squad EFL63509 Horn Set Inverza BNF Gestange und Inverza 280 BNF rette Inverza 280 BNF 280 BNF Ruderhorn Set EFLA7300 Ubs om Brushless E flite 10 Amp eee brushless Regolatore ESC Brushless ESC brushless 10A EFLR7100 3 5 g Digital Sub E flite 3 5g Digital Sub micro servo Servo digitale submicro Micro Servo Servo digital 3 5g da 3 5g BL 280 Outrunner E flite BL 280 Moteur BL 280 cage BL 280 motore a cassa EFLM7010 Motor 1800Kv AuBenlaufer Motor tournante 1800Kv
11. aircraft disconnect and binding to trans reconnect flight battery to aircraft and follow mitter binding instructions Bind switch or button not held long enough during Power off transmitter and repeat bind process bind process Hold transmitter bind button or switch until receiver is bound Flight battery Transmitter battery charge is too low Replace recharge batteries Bind pins on receiver are not correctly Connect receiver bind pins as instructed and connected bind transmitter to receiver Aircraft or transmitter is too close to large metal Move aircraft and transmitter to another object wireless source or another transmitter location and attempt binding again Aircraft will not Transmitter too close to aircraft during connecting Power off transmitter move transmitter a connet after process larger distance from aircraft disconnect and binding to trans reconnect flight battery to aircraft mitter Flight battery Transmitter battery charge is too low Replace recharge batteries Aircraft bound to different model memory Select correct model memory on transmitter ModelMatch radios only Transmitter may have been bound using different Bind aircraft to transmitter DSM protocol Bind pins on receiver are connected nsure bind pins on receiver are not connected Aircraft or transmitter is too close to large metal Move aircraft and transmitter to another loca object wireless source or another transmitter tion and attempt connecti
12. anner could result in injury or damage to the product or other property This product is not intended for use by children without direct adult supervision Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby Inc This manual contains instructions for safety operation and maintenance It is essential to read and follow all the instructions and warnings in the manual prior to assembly setup or use in order to operate correctly and avoid damage or serious injury Age Recommendation Not for children under 14 years This is not a toy Safety Precautions and Warnings e Always keep a safe distance in all directions around your model to avoid collisions or injury This model is controlled by a radio signal subject to interference from many sources outside your control Interference can cause momentary loss of control e Always operate your model in open spaces away from full size vehicles traffic and people e Always carefully follow the directions and warnings for this and any optional support equip ment chargers rechargeable battery packs etc e Always keep all chemicals small parts and anything electrical out of the reach of children e Always avoid water exposure to all equipment not specifically designed and protected for this purpose Moisture causes damage to electronics e Never place any portion of the model in your mouth as it could caus
13. d mode Refer to your transmit ter s manual for binding button or switch instructions 8 After 5 to 10 seconds the receiver status LED will become solid indicating that the receiver is bound to the transmitter If the LED does not turn solid refer to the Troubleshooting Guide at the back of the manual Preflight Checklist C ZZ 1 Charge flight battery 2 Install flight battery in aircraft once it has been fully charged b s 3 Bind aircraft to transmitter 4 Make sure linkages move freely 5 Perform Control Direction Test with transmitter i 6 Adjust center of gravity 7 Perform a radio system Range Check i 8 Find a safe and open area 9 Plan flight for flying field conditions A CAUTION When using a Futaba transmitter with a Spektrum DSM module you must reverse the throttle channel and rebind Refer to your Spektrum module manual for binding and failsafe instructions Refer to your Futaba transmitter manual for instructions on reversing the throttle channel WU cme set DND ECENER oer LITER NAN Gz GG Weg Installing the Flight Battery L Remove the battery hatch from the nose of the aircraft 2 Apply the included strip of hook and loop tape in the center on the bottom of your battery 3 For the recommended CG install the battery centered in the compartment then press the battery onto the hook and loop strip A See the Adjusting the Center of Gravity instruct
14. e serious injury or even death e Never operate your model with low transmitter batteries e Always keep aircraft in sight and under control e Always use fully charged batteries e Always keep the transmitter powered on while aircraft is powered e Always remove batteries before disassembly e Always keep moving parts clean e Always keep parts dry e Always let parts cool after use before touching e Always remove batteries after use e Always ensure failsafe is properly set before flying e Never operate aircraft with damaged wiring e Never touch moving parts he E flite Inverza 280 Bind N Fly Basic aircraft designed by world champion Quique Somenzini has been specifically built to provide exceptional precision scale and 3D aerobatic performance so that you can fly from practically anywhere such as a park or small field Everything you love about flying larger performance aerobatic airplanes has been packed into the Inverza 280 Beyond its advanced composite reinforced foam construction you ll appreciate how its expert approved digital control and custom tuned power system components are installed which make it possible for you to get flying fast Along with your favorite DSM2 DSMX compatible transmitter you can further assure the value of this performance model is maintained by considering a quality 11 1V Li Po flight battery such as the E flite 450mAh 3S 11 1V 50C Li Po 18AWG JST EFLB4503SJ50 and a re
15. e spinner is fully connected to the spinner back plate for safe operation 13 Troubleshooting Guide Problem Possible Cause Solution Aircraft will ESC did not arm because throttle stick and or Lower throttle stick and throttle trim to lowest not respond to throttle trim too high setting throttle but re sponds to other Throttle channel is reversed Reverse throttle channel on transmitter controls Motor disconnected from ESC Make sure motor is connected to the ESC Servo travel set up is less than 100 Adjust servo travel to 100 or slightly greater Extra propeller Damaged propeller spinner or motor Replace damaged parts noise or extra sten Prop nut is too loose Tighten the prop nut Prop is out of balance Remove and balance propeller or replace with a balanced propeller Spinner is not tight or fully seated in place Tighten the spinner or remove the spinner and turn it 180 degrees Reduced flight Flight battery charge is low Completely recharge flight battery lime or aircratt gt Speller installed backward install propell Flight battery damaged Replace flight battery and follow flight battery instructions Flight battery is too cold Make sure battery is warm before use Battery capacity too low for flight conditions Replace battery or use a larger capacity battery Aircraft will not Transmitter too near aircraft during binding process Power off transmitter move transmitter a Bind during larger distance from
16. egulations OTHER THAN THE EXPRESS WARRANTY ABOVE HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF NON INFRINGEMENT MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER S INTENDED USE Purchaser s Remedy Horizon s sole obligation and purchaser s sole and exclusive remedy shall be that Horizon will at its option either i service or ii replace any Product determined by Horizon to be defective Horizon reserves the right to inspect any and all Product s involved in a warranty claim Service or replacement decisions are at the sole discretion of Horizon Proof of purchase is required for all warranty claims SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER S SOLE AND EXCLUSIVE REMEDY Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT WARRANTY TORT NEGLIGENCE STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Further in no event shall the liability of Horizon exceed the individual price of the Product on which
17. hatch and install the flight battery to the hook and loop strip then connect the battery to the ESC noting proper polarity mf Series of tones Y Continuous LED Installing the Wing 1 Slide the wing tube into the right wing 2 Insert the right wing with the wing tube A into the round hole in the wing slot of the fuselage while connecting the right aileron control NOTICE When disconnecting the servo connectors do not pull on the servo wires Use a screwdriver or pliers to break the friction fit of the servo connectors Failure to do so could result in damage to the servo wiring 3 Install the left wing B by sliding it over the wing tube to the fuselage while connecting the left aileron control 4 Invert the fuselage so the landing gear is facing up Secure the left and right wing to the fuselage using the included screws C 5 Remove the receiver cover D from the bottom of the fuselage 6 Connect the aileron servos in the wings to the Y harness connectors in the fuselage The left and right aileron servos can be connected to either side of the Y harness Tip If you are using dual aileron flaperon transmitter programming connect the aileron servo connectors to the AILE and AUX1 ports on the receiver instead of using the included Y harness After connecting the servos to the separate ports program your transmitter for dual aileron flaperon and differential to benefit from the high performa
18. iod of 60 days from notification after which it will be discarded ATTENTION Horizon service is limited to Product compliant in the country of use and ownership If received a non compliant Product will not be Warranty and Service Information Country of Purchase Horizon Hobby Address Phone Number Email Address 4105 Fieldstone Rd 877 504 0233 Champaign Illinois Online Repair Request visit 61822 USA www horizonhobby com service 4105 Fieldstone Rd Champaign Illinois 877 504 0233 61822 USA Units 1 4 Ployters Rd Staple Tye 44 0 1279 641 097 Harlow Essex sales horizonhobby co uk CM18 7NS United Kingdom Horizon Technischer Christian Junge StraBe 1 49 0 4121 2655 100 Service 25337 Elmshorn Germany service horizonhobby de 11 Rue Georges Charpak 33 0 1 60 18 34 90 France Horizon Hobby SAS 77127 Lieusaint France infofrance horizonhobby com Room 506 No 97 Changshou Rd 86 021 5180 9868 Compliance Information for the European Union Declaration of Conformity in accordance with ISO IEC 17050 1 No HH2013032601U1 Product s Inverza 280 BNF Basic C Item Number s EFL6350 Equipment class 1 Horizon Service Center United States Electronics and engines of America Horizon Product Support All other products United Kingdom Horizon Hobby Limited Germany The object of declaration described above is in conformity with the requirements of the specifications listed below following the pro
19. ions for more information 4 Connect a fully charged flight battery to the ESC See the Arming the ESC instructions for correct connection of the battery to the ESC 5 Reinstall the battery hatch A CAUTION Always disconnect the Li Po battery from the ESC when not flying to eliminate power supplied to the motor The ESC does not have an arming switch and will respond to any transmitter input when a signal is present A CAUTION Always disconnect the Li Po battery from the ESC when not flying to avoid over discharging the battery Batteries discharged to a voltage lower than the lowest approved voltage may become damaged resulting in loss of performance and potential fire when batteries are charged Arming the ESC Arming the ESC also occurs after binding as previously described but subsequent connection of a flight battery requires the steps to the right Tip If the ESC sounds a continuous double beep after the flight battery is connected recharge or replace the battery If you accidentally connect the battery while the throttle is fully opened a musical tone will sound after 5 seconds and the ESC will enter programming mode Disconnect the battery immediately A CAUTION Always keep hands away from the Lower throttle and throttle trim to lowest propeller When armed the motor will turn the settings propeller in response to any throttle movement Power on the Transmitter Remove the magnetic battery
20. liable charger such as the E flite Celectra 80W AC DC Multi Chemistry Battery Charger EFLC3025 Please be sure to read through this manual carefully so that you can successfully enjoy all the benefits this outstanding E flite model has to offer Box Contents Table of Contents Low Voltage Cutoff LVC cccsssssessessesserees 4 Removing the Landing Gear 11 Transmitter and Receiver Binding eeeennen 4 Flying Tips and ReEpalFS i 12 Preflight Lhecklet i 4 Post Flight Checklist 12 Installing the Flight Battery eenn 5 Serviceof Power Components ccccreen 13 Arming the EL 6 TroubleshootingGuide 14 Installing the Wing EEN 7 Limited Warranyy scasacesietesreecnieroueseecvetesnrestvanacnndes 15 Control Direction Test 8 Warranty and Service Information 16 Control Centering seserinis 8 Compliance Information for the European Union 16 Settings for Servo Am 8 Replacement Parts rino 62 Dual Rates and EXpOS eeneeeeeereerrerrrernenn 9 Optional Replacement and Accessories 63 Adjusting Center of Gravity CG 10 Parts ContactInformation 63 Specifications Installed Motor BL 280 Outrunner Motor AC 1800Kv EFLM7010 SEE o
21. med position Ailerons Elevator Rudder IMPORTANT The factory setting for the elevator servo arm is one tooth forward from a 90 angle to allow equal elevator deflection up and down All other control surface servo arms should be set to 90 Dual Rates and Expos We recommend using a DSM radio capable of dual rates and expo The settings to the right are recommended starting settings for intermediate pilots Adjust according to individual preferences after the initial flight Tip For the first flight fly the model at LOW RATE or For more information videos and advanced settings for expert pilots including Quique explaining how to fly the EFL Inverza aircraft visit www E fliteRC com Inverza Also available for download are Quique s DX8 DX7s and DX18 programs for this aircraft This programming is at an expert level and includes some mixing and differential Measuring Control Throws Below are the locations on this aircraft to measure the recommended low and high rate control throws distance in both directions Rudder From the center line A deflect the leading edge of the rudder B Elevator From the center line C deflect the trailing edge of the elevator D Ailerons From the center line guide E deflect the trailing edge of the aileron F High Rate 25mm A V Low Rate 12mm A V 35mm A V 7mm A V 20mm lt gt 10mm lt gt 40 30 60
22. nce characteristics of this aircraft E T N ict na SS C Control Direction Test You should bind your aircraft and transmitter before doing these tests Move the controls on the transmitter to make sure the aircraft control surfaces move correctly and in the proper direction Control Centering Before the first flights or in the event of an ac cident make sure the flight control surfaces are centered Adjust the linkages mechanically if the control surfaces are not centered 1 Make sure the control surfaces are neutral when the transmitter controls and trims are centered The transmitter sub trim must always be set to zero 2 When needed use a pair of pliers to carefully bend the metal linkage see illustration 3 Make the U shape narrower to make the connector shorter Make the U shape wider to make the linkage longer Settings for Servo Arms This illustration shows the factory settings for linkages on servo arms After flying you may choose to adjust the linkage positions for the desired control response This illustration shows the factory setting for the Elevator servo arm on the servo Make sure the tail linkages move freely and that paint or decals are not adhered to them Centering Controls After First Flights H the model requires excessive transmitter trim return the transmitter trim to zero and adjust the linkages mechanically so that the control surfaces are in the flight trim
23. ng again Control surface Control surface control horn linkage or Replace or repair damaged parts and adjust does not move servo damage controls Wire damaged or connections loose Do a check of wires and connections connect or replace as needed Flight battery charge is low Fully recharge flight battery Control linkage does not move freely Make sure control linkage moves freely Controls reversed Transmitter settings reversed Adjust controls on transmitter appropriately Motor power Battery voltage is down to the point of receiver ESC Recharge flight battery or replace battery that quickly decreas Low Voltage Cutoff LVC is no longer performing es and increases then motor loses power 14 Limited Warranty What this Warranty Covers Horizon Hobby Inc Horizon warrants to the original purchaser that the product purchased the Product will be free from defects in materials and workmanship at the date of purchase What is Not Covered This warranty is not transferable and does not cover i cosmetic damage ii damage due to acts of God accident misuse abuse negligence commercial use or due to improper use installation operation or maintenance iii modification of or to any part of the Product iv attempted service by anyone other than a Horizon Hobby authorized service center v Product not purchased from an authorized Horizon dealer or vi Product not compliant with applicable technical r
24. o di carica con JST Female JST Buchse prise JST femelle femmina JST EFLA250 Park Flyer Tool Assort Park Flyer Werkzeug Assortiment d outils Park Flyer assorti ment 5 pc sortiment 5 teilig park flyer 5pc mento attrezzi 5 pc 450mAh 3S 11 1V 450mAh 3S 11 1V Li Po 11 1V 3S 450mAh 3S 11 1V EFLB4503SJ50 50C LiPo 18AWG JST 50C LiPo Akku JST 450mA 50C prise JST 50C LiPo 18AWG JST RECOMMENDED EMPFOHLEN RECOMMANDEE CONSIGLIATA 450mAh 3S 11 1V 450mAh 3S 11 1V Batterie Li Po 11 1V Batteria Li Po EFLB4503SJ30 30C Li Po 18AWG 30C Li Po 18AWG 3S 450mA 30C 450mAh 3S 11 1V JST JST Akku 18AWG JST 30C 18AWG JST Celectra 80W AC E flite 80W AC Chargeur de batterie Celectra 80W AC EFLC3025 DC Multi Chemistry DC Multi Akku Celectra 80W AC DC DC Caricabatterie Battery Charger Ladegerat EU multiplo DX6i DSMX 6 Channel DX6i DSMX 6 Kanal Emetteur DX6i DSMX DX6i DSMX Trasmet Transmitter Sender 6 voies titore 6 canali DX7s DSMX Spektrum DX7s Emetteur DX7s DSMX DX7s DSMX 7 Channel Transmitter 7 Kanal Sender 7 voies Trasmettitore 7 canali K DSMX Transmitter Spektrum DX8 nur Emetteur DX8 DSMX DX8 DSMX trasmet Sender 8 voies titore 8 canali P 8 DX18QQ Spektrum DX18 Emetteur DX18 DX18 DSMX DX18QQ Transmitter DX18QQ nur Sender Ge SH DSMX 18 trasmettitore 18 canali Parts Contact Information Kontaktinformationen fur Ersatzteile Coordonn es pour obtenir de pieces d tach
25. st your timer for longer or shorter flights once you have flown the model Flights of 7 minutes are achievable if using proper throttle management NOTICE Repeated flying to LVC will damage the battery Transmitter and Receiver Binding Binding is the process of programming the receiver to recognize the GUID Globally Unique Identifier code of a single specific transmitter You need to bind your chosen Spektrum DSM2 DSMX technology equipped aircraft transmitter to the receiver for proper operation Any full range Spektrum DSM2 DSMX transmitter can bind to the DSM2 DSMX receiver Please visit www bindnfly com for a complete list of compatible transmitters v Binding Procedure 1 Refer to your transmitter s unique instructions for binding to a receiver location of transmitter s Bind control 2 Make sure the flight battery is disconnected from the aircraft 3 Power off the transmitter 4 Bind the AR6310 receiver to a DSM2 DSMX transmitter by shorting the bind pins A with tweezers a hemostat or small needle nose pliers Metal to metal contact is needed to com plete the circuit Do not bend the bind pins 5 Connect the flight battery to the aircraft Short the pins until the receiver LED begins to flash rapidly typically after 5 seconds 6 Ensure that control surface trims are centered and the throttle and throttle trims are in the low position to correctly set the failsafe 7 Put your transmitter into bin
26. the country you live and use the Product in please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization RMA number Pack the Product securely using a shipping carton Please note that original boxes may be included but are not designed to withstand the rigors of shipping without additional protection Ship via a carrier that provides tracking and insurance for lost or damaged parcels as Horizon is not responsible for merchandise until it arrives and is accepted at our facility An Online Service Request is available at http www horizonhobby com content _ service center_render service center If you do not have internet access please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service When calling Horizon you will be asked to provide your complete name street address email address and phone number where you can be reached during business hours When sending product into Horizon please include your RMA number a list of the included items and a brief summary of the problem A copy of your original sales receipt must be included for warranty consideration Be sure your name address and RMA number are clearly written on the outside of the shipping carton NOTICE Do not ship LiPo batteries to Horizon If you have any issue with a LiPo battery please contact the appropriate Horizon
27. visions of the European R amp TTE directive 1999 5 EC and EMC Directive 2004 108 EC EN301 489 1 V1 9 2 2012 EN301 489 17 V2 1 1 2009 Ze e e PAL EN55022 2010 AC 2011 EN55024 2010 Steven A Hall Signed for and on behalf of Executive VP Chief Operating Officer Horizon Hobby Inc International Operations and Risk Management Champaign IL USA Horizon Hobby Inc Mar 26 2013 Instructions for disposal of WEEE by users in the European Union This product must not be disposed of with other waste Instead it is the user s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural Ms resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local city office your household waste disposal service or where you purchased the product 16 Replacement Parts Ersatzteile Pieces de rechange Recapiti per i ricambi Part e Nummer en e es Num ro e Codice Description Beschreibung Description Descrizione Fuselage with E flite Inverza 280 Fuselage avec d rive Fusoliera con timone EFL63501 rudder Inverza 280 BNF Rumpf mit Inverza 280 BNF Inverz
Download Pdf Manuals
Related Search