Mobotix MX-PTMOUNT-OPT-PW
Contents
1. address bar of the browser Step 3 Adjust PTMount According to Live Image e Adjust the sensor module by watching the live image of the camera Firmly tighten all screws of the PTMount Exchanging a Sensor Module C FC 2014 Declaration of Conformity www mobotix com gt Support gt Media Library gt Certificates Make sure the power supply to the camera is disconnected before e Use the Allen wrench or a small screw installing or replacing a sensor module driver to lift the sensor module out of the insert as shown Take care not to damage the sealing of the sensor module housing e Ifthe small bar on the insert is not point ing towards the hole of the grub screw add a mark at the present position Remove the two fastening screws and rotate the insert so that the small bar points to the hole of the grub screw Tighten the two fastening screws e Remove the bayonet catch and the sensor cable from the old module Attach the sensor cable to the new sensor module connect the sensor cable apply bayonet catch and lock by turning to the right e Loosen the grub screw that locks the sensor module within the insert Insert the sensor module as described in Section Installation of PTMount and Sensor Module f required rotate the insert to its original position and check the camera s live image as described in Section Initial Op eration S15D with PTMount Tighten all screws you loosened before E2. MX PTMount OPT O 2 Q O z S S PTMount MOBOTIX S15D with 2 sensor modules each in PTMount S15D Modular PoE network camera with max two sensor modules for con cealed installation not included All components weatherproof S15D IP65 sensor modules IP66 30 to 60 C 22 to 140 F Day and Night sensor modules can be freely combined Sensor module connection cables max 2 m each e g for indoors outdoors Quick Install JA A Security Vision Systems MOBOTIX PTMount for MOBOTIX S15D Sensor Modules 6 P6 genna We C1 22 t0 140 F 30 to 60 Manually adjustable dome mount for one MOBOTIX sensor module housing S15D S14D not included freely turning along three axes for wall ceiling and upright installations 31 988 _EN_V1_07 2014 Standard Delivery Item Count Part Name 11 1 Sphere with freely rotating insert installed 1 2 1 Foot installed L3 1 Base plate installed 1 4 1 Swivel ring installed 1 5 1 Sealing 1 6 4 Washer 4 3 mm stainless steel 1 7 4 Wood screw 4x40 mm stainless steel 1 8 4 Screw anchor S6 1 9 1 Allen wrench 2 5 mm Adjustable Along Three Axes Flexible Installation Panning Rotating Mounting to a Ceiling Mounting to a Wall Mounting upright Preparatory Steps e Using the supplied Allen wrench re move the two screws that hold the foot onto the swivel ring e Remove the
3. cept has made high resolution video systems cost efficient MOBOTIX AG Security Vision Systems D 67722 Langmeil e Phone 49 6302 9816 103 Fax 49 6302 9816 190 sales mobotix com PTMount Quick Install JA A Security Vision Systems MOBOTIX Initial Operation S15D with PTMount Step 1 Establish Network Connection and Power Supply Optional Exchange the Sensor Modules in the Dual Image e Connect the network port of the camera to a router or switch see e In the camera s browser interface click on the Admin Menu button 15 Camera Manual Section Network and Power Connection Ad and in the Hardware Configuration section open the Image Sensor ditional Cables Configuration dialog e f you do not use a PoE switch establish the power supply of the e You can use the Left Sensor Right Sensor dropdown fields to select camera using a PoE Power Adapter MX NPA Box the sensor module External sensor Cam External sensor Cam2 that e Configure the camera for your network see 75 Camera Manual will be shown at the left or at the right in the dual image Section Manual and Automatic Operation e Close the dialog and save the configuration of the camera Step 2 Open User Interface in Browser e Monitor the camera LEDs and make sure that the S15D is ready green LED is on red LED flashes slowly see S15 Camera Manual Section Camera Startup Sequence e Enter the IP address of the camera you determined in Step 7 in the
4. gy and its decentralized concept has made high resolution video systems cost efficient O 2 Q e z S S MOBOTIX AG Security Vision Systems D 67722 Langmeil e Phone 49 6302 9816 103 Fax 49 6302 9816 190 sales mobotix com
5. ing screws of the insert 1 then rotate the insert so that the small bar opposite of the TOP OBEN label points to the hole of the grub screw 2 Secure the insert against rotating by tightening the two fastening screws Innovations Made in Germany Attach the sensor module cable to the sensor module turn blue bayonet catch to the left and remove pull out the plug connect the sensor cable apply bayonet catch and lock by turn ing to the right Push the sensor module into the PTMount so that the MOBOTIX let tering is turned 90 degrees to the left vs the TOP OBEN lettering Using the module wrench red or black A0P f OBc ERS poB lock the sensor module by turning it e 90 degrees to the right Secure the sensor module by tighten ing the grub screw using the supplied Allen wrench The grub screw locks the sensor module within the insert and prevents inadvertent unlocking of the sensor module Adjust the sensor module temporarily by pointing it into the desired viewing direction Make sure that the TOP OBEN label on the insert is pointing upwards If this is not the case loosen the two fastening screws and rotate the insert Lightly tighten the two fastening screws Continue to bring the camera into service as described in Section Initial Operation S15D with PTMount The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its decentralized con
6. swivel ring and the base plate Make sure that there is enough space 104 mm for installing the PTMount and that you can access it from the rear later 2 R on The surface should be even and smooth so that the sealing lies flat properly Drill the holes for the base plate drilling template see Section Dimensions Drilling Template In the center of the drilling template drill another hole into the wall or faceplate for the sensor cable Since you will lt push the hinged ferrite through this ka lt a so hole later on the hole should have gt s ey el a diameter between 15 and 35 mm CE oon j Insert the screw anchors into the holes if required SS ee Installation of PTMount and Sensor Module e Hold the sealing the swivel ring and the base plate as shown in the figure e Attach the base plate using the sup plied wood screws and washers When tightening the screws make sure that you can still rotate the swivel ring by hand Carefully guide the sensor cable through the sealing the swivel ring and the base plate then attach the hinged ferrite to the cable Push the sensor cable into the wall ceiling so as to completely hide the ferrite Guide the sensor cable from the back into the foot and the sphere e Use the two screws to affix the foot and sphere assembly to the swivel ring and make sure that the foot can still be rotated e Loosen the two fasten
7. xample for wall installation e Using the module wrench red or j black unlock the sensor module by turning it 90 degrees to the left Dimensions Drilling Template 104 mm 4 09 in 94 mm 3 70 in L12 86 mm 3 39 in L25 L160 92 mm 3 62 in 104 mm 4 09 in Base plate mounted to wall ceiling Hole for cable Swivel ring can be rotated Sealing 104 mm 4 09 in Notes e This product must not be used in locations exposed to the dangers e Only install this product in or on suitable solid materials that provide of explosion for a sturdy installation of the fixing elements used e Make sure that you install the S15D and this product as outlined in the e The PTMount dome mount is only to be used in combination with the installation instructions in this document and in Chapter 2 Installation MOBOTIX S15D and MOBOTIX sensor module housing of the 75 Camera Manual www mobotix com gt Support gt Manuals e Make sure that the operating temperature of 30 to 60 C 22 to 140 F e When installing this product make sure that you are only using genuine is not exceeded MOBOTIX parts and MOBOTIX connection cables The MOBOTIX YouTube Channel www youtube com MOBOTIXAG Your Copyright MOBOTIX AG 2014 Made in Germany Technical information subject to change without notice Innovations Made in Germany The German company MOBOTIX AG is known as the leading pioneer in network camera technolo
Download Pdf Manuals
Related Search