Remington 43162.560.100
Contents
1. the head must be cut over the top of a flat comb Use a closer guide comb to taper the hair down to the neckline as desired lt gt CARE FOR YOUR HAIRCLIPPER Your clipper is fitted with high quality blades To ensure long lasting performance of your clipper clean the blades and unit regularly Always keep the attachment guide comb on the trimmer blade Ak AFTER EACH USE Ensure the clipper is switched off and disconnected from the mains before cleaning Brush the accumulated hair from the blades Do not submerge the clipper in water To clean unit wipe with damp cloth and dry immediately EVERY SIX MONTHS At regular intervals the blade set should be removed and cleaned Remove the 2 screws retaining the fixed blade with a screwdriver Do not remove blade set Brush out hairs from between the blades with soft cleaning brush Do not remove the lubricating grease from the blades It is not necessary to remove the small moving blade from the unit If the moving blade has been removed this can be re fitted by slotting the coated blade holder over the pin in the centre of the interior product head The groove on the coated blade just below the teeth rests on a metal plate at the opposite side to the screw holes The fixed blade is fitted with the raised profile pointing outwards and fixed with the 2 screws Note that if the blades are not correctly aligned then cutting efficiency will be impaired Place a few drops of cutter or sewing machi2. Po PV NEON PRO POWER 000000 W Wi Y Y D Y Y Y Y b Y Y Y Y Y Y Y Y W W Y Y W W Wi ho 6 y 0600 y Y 0000 O0 0 0 0 0 6 666000 00000000 DO 0000008008008 bo O O0 000000 O0 000 x J J eee 60 0000 v O 00060660 AXXXXXXXXXXXXY 00000 0000000 0000000000000 e 0 O h h N BV NEON Thank you for choosing Remington Our products are designed to meet the highest standard of quality functionality and design We hope you enjoy using your new Remington product Please read the instructions for use carefully and keep in a safe place for future reference Claim your extra 1 year warranty by registering your product online Simply go to www productregister co uk remington IMPORTANT SAFEGUARDS 1 WARNING TO REDUCE THE RISK OF BURNS ELECTROCUTION FIRE OR INJURY TO PERSONS 2 Use this appliance only for its intended use as described in this manual Do not use attachments not recommended by Remington 3 Do not use this product if it is not working correctly if it has been dropped or damaged or dropped in water An appliance should never be left unattended when plugged in to a power outlet except when charging Keep the power plug and cord away from heated surfaces Make sure the power plug and cord do not get wet Do not plug or unplug the appliance with wet hands Do not use the product with a damaged cord A replacement can be obtained via our I
3. by replacement or repair at our option provided the product is used and maintained in accordance with the instructions Defects from repair by an unauthorized dealer are not covered Consumables are excluded Your statutory rights are not affected If you call the Service Centre please have the Model No to hand as we won t be able to help you without it The Model No can be found on the rating plate of the appliance Replacement parts and accessories are available to buy at www remington co uk parts accessories BV NEON SERVICE CENTRE United Kingdom ZA Tel 0800 212 438 free call mainland UK A 44 161 947 3111 call outside the UK Spectrum Brands UK Ltd Fir Street Failsworth Manchester M35 OHS UK www remington co uk Ireland Tel 142 951 40 Remington Consumer Products Unit B12 Ballymount Corporate Park Ballymount Dublin 12 www remington co uk gt REGISTER ONLINE FOR 10 000 prize draw EXTRA year guarantee FREE rewards gallery Visit www productregister co uk remington You must register within 28 days of purchase Model No HC5200 13 UK HC5200 1T22 0001001 Version 01 13 Remington is a Registered Trade Mark of Spectrum Brands Inc or one of its subsidiaries Spectrum Brands UK Ltd Fir Street Failsworth Manchester M35 OHS www remington co uk 2013 SBI
4. ds and outwards through the hair trimming just a little at a time 3 STEP 2 Back of the head With the comb set at 12mm or 18mm cut the hair at the back of the head 3 STEP 3 Side of the head Set the comb to 3mm or 6mm trim sideburns Then change the setting to 9mm and continue to cut the top of the head STEP 4 Top of the head Use the longer length comb attachment and set it to 24mm or 27mm then cut hair on top of the head against the direction in which the hair normally grows For longer hair on top use the longer length comb attachment 24 42mm to achieve the desired style Always work from the back of the head X STEP 5 The finishing touches Use the clipper without an attachment comb for close trimming around the base and sides of the neck To produce a clean straight line at the sideburns reverse the hair clipper Place the reversed clipper at right angles to the head tips of the blades lightly touching the skin and then work downwards PV NEION ka SHORT TAPERED STYLES FLAT TOPS amp SHORT CUTS Starting with the longest guide comb attached 24 42mm cut from the back of the neck to the crown Hold the guide comb flat against the head and slowly move the clipper through the hair Use the same procedure from the lower side to the upper side of the head Then cut the hair against the direction in which it grows and level with the sides To give a flat top look the hair on top of
5. fety isolating adaptors PA 3215E for EU version or PA 3215U for UK version with the output capacity of 3 2V dc 1500mA 3 CORDED USE Connect the charging adaptor to the product then to the mains CAUTION Extended mains only use will result in the reduction of the battery life Keep the appliance dry 3 CORDLESS USE When the unit is switched on and fully charged the product can be used in cordless mode for up to 40 minutes lt gt HOW TO USE ka BEFORE STARTING THE CUT Inspect the clipper making sure that it is free from hair and dirt Seat the person so that their head is approximately at your eye level Before cutting always comb the hair so it is tangle free and dry Em om 3 TO ATTACH A COMB Hold the comb with its teeth upward Slide it onto and along the clipper blade until the front of the comb firmly sits against the clipper blade 3 TO REMOVE THE COMB Holding the clipper with the blades facing away from you firmly push the comb upward and away from the blades XE INSTRUCTIONS FOR HAIR CUTTING Note For even cutting allow the comb attachment blade to cut its way through the hair Do not force it through quickly If you are cutting for the first time start with the maximum comb attachment os STEP 1 Nape of the neck Set the comb to 3mm or 6mm Hold the clipper with the blade teeth pointing upwards Begin starting at the centre of the head at the base of the neck Slowly lift the clipper working upwar
6. ne oil onto the blades Wipe off excess oil XE CLEANING CAUTIONS Only the attachment guide combs and trimmer blade may be removed from the product for cleaning Cleaning should be done with a soft brush such as the brush supplied with the product Do not rinse under water Do not use harsh or corrosive cleaners on the units or their blades Ensure the appliance is switched off and unplug from the main outlet before cleaning amp ENVIRONMENTAL PROTECTION To avoid environmental and health problems due to hazardous substances in electrical i and electronic goods appliances marked with this symbol must not be disposed of with unsorted municipal waste but recovered reused or recycled BATTERY REMOVAL The battery must be removed from the appliance before it is scrapped The appliance must be disconnected from the supply mains when removing the battery Ensure that the clipper is discharged of all power and disconnected from the mains Remove the screw cover from back housing Using a small screwdriver remove 1 screw from the bottom of the clipper Pry the front panel from the front housing and expose the PCB and batteries Pry the PCB assembly from the housing Cut or break the wire stamps on the both end of the batteries and remove the batteries The battery is to be disposed of safely m SERVICE AND GUARANTEE Defects affecting product functionality appearing within the guarantee period will be corrected
7. nternational Service Centres 9 Do not twist or kink the cable and don t wrap it around the appliance 10 Store the product at a temperature between 15 C and 35 C 11 Only use the parts supplied with the appliance 12 The appliance including its cord must not be used played with cleaned or maintained by persons under eight years old and should at all times be kept out of their reach 13 Use cleaning or maintenance of the appliance by children over eight or by anyone with a lack of knowledge experience or with reduced physical sensory or mental capabilities should only be undertaken after receiving appropriate instruction and under the adequate supervision of a responsible adult to ensure that they do so safely and that the hazards involved are understood and avoided WARNING Keep the appliance dry AK CON O U KEY FEATURES On Off Switch Blade set 2 attachment guide combs 3 21mm and 24 42mm 3mm adjustment Charging indicator light Power Port Adaptor O U RUN gt V NEON GETTING STARTED CHARGING YOUR HAIRCLIPPER Ensure the product is switched off Connect the charging adaptor to the product and then to the mains If the product is not going to be used for an extended period time 2 3 months unplug it from the mains and store Fully recharge your product when you would like to use it again Allow 16 20 hours for a full charge This appliance should be charged by approved sa
Download Pdf Manuals
Related Search